mx53: Add Board support for GE PPD

Create board support for GE PPD, based on mx53loco.

Use mx53ppd_defconfig make target to configure for this board.

Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

1 files changed, 248 insertions, 0 deletions

diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h
new file mode 100644
index 0000000000..92dd845c70
--- /dev/null
+++ b/include/configs/mx53ppd.h
@@ -0,0 +1,248 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * Configuration settings for Freescale MX53 low cost board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+#define CONSOLE_DEV	"ttymxc0"
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_SYS_FSL_CLK
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 8000
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE	UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_ESDHC_NUM	2
+
+#define CONFIG_SUPPORT_RAW_INITRD	/* bootz raw initrd support */
+
+/* Eth Configs */
+#define CONFIG_MII
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE	FEC_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR	0x1F
+
+/* USB Configs */
+#define CONFIG_USB_EHCI_MX5
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_MXC_USB_PORT	1
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+#define CONFIG_SYS_RTC_BUS_NUM		2
+#define CONFIG_SYS_I2C_RTC_ADDR	0x30
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_DIALOG_POWER
+#define CONFIG_POWER_FSL
+#define CONFIG_POWER_FSL_MC13892
+#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR	0x48
+#define CONFIG_SYS_FSL_PMIC_I2C_ADDR	0x8
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_ETHPRIME		"FEC0"
+
+#define CONFIG_LOADADDR		0x72000000	/* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE    0x77800000
+
+#define PPD_CONFIG_NFS \
+	"nfsserver=192.168.252.95\0" \
+	"gatewayip=192.168.252.95\0" \
+	"netmask=255.255.255.0\0" \
+	"ipaddr=192.168.252.99\0" \
+	"kernsize=0x2000\0" \
+	"use_dhcp=0\0" \
+	"nfsroot=/opt/springdale/rd\0" \
+	"bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
+		"${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
+	"choose_ip=if test $use_dhcp = 1; then set kern_ipconf ip=dhcp; " \
+		"set getcmd dhcp; else set kern_ipconf " \
+		"ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; " \
+		"set getcmd tftp; fi\0" \
+	"nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} " \
+		"${nfsserver}:${image}; bootm ${loadaddr}\0" \
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	PPD_CONFIG_NFS \
+	"bootlimit=10\0" \
+	"image=/boot/fitImage\0" \
+	"fdt_high=0xffffffff\0" \
+	"dev=mmc\0" \
+	"devnum=0\0" \
+	"rootdev=mmcblk0p\0" \
+	"quiet=quiet loglevel=0\0" \
+	"console=" CONSOLE_DEV "\0" \
+	"lvds=ldb\0" \
+	"setargs=setenv bootargs ${lvds} jtag=on mem=2G " \
+		"vt.global_cursor_default=0 bootcause=${bootcause} ${quiet} " \
+		"console=${console} ${rtc_status}\0" \
+	"bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} ro " \
+		"rootwait ${bootargs}\0" \
+	"doquiet=if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
+		"then setenv quiet; fi\0" \
+	"hasfirstboot=ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
+		"/boot/bootcause/firstboot\0" \
+	"swappartitions=setexpr partnum 3 - ${partnum}\0" \
+	"failbootcmd=" \
+		"ppd_lcd_enable; " \
+		"msg=\"Monitor failed to start.  " \
+			"Try again, or contact GE Service for support.\"; " \
+		"echo $msg; " \
+		"setenv stdout vga; " \
+		"echo \"\n\n\n\n    \" $msg; " \
+		"setenv stdout serial; " \
+		"mw.b 0x7000A000 0xbc; " \
+		"mw.b 0x7000A001 0x00; " \
+		"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+	"altbootcmd=" \
+		"run doquiet; " \
+		"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+		"run hasfirstboot || setenv partnum 0; " \
+		"if test ${partnum} != 0; then " \
+			"setenv bootcause REVERT; " \
+			"run swappartitions loadimage doboot; " \
+		"fi; " \
+		"run failbootcmd\0" \
+	"loadimage=" \
+		"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
+	"doboot=" \
+		"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+		"run setargs; " \
+		"run bootargs_emmc; " \
+		"bootm ${loadaddr}\0" \
+	"tryboot=" \
+		"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+		"run loadimage || run swappartitions && run loadimage || " \
+			"setenv partnum 0 && echo MISSING IMAGE;" \
+		"run doboot; " \
+		"run failbootcmd\0" \
+	"video-mode=" \
+		"lcd:800x480-24@60,monitor=lcd\0" \
+
+#define CONFIG_MMCBOOTCOMMAND \
+	"if mmc dev ${devnum}; then " \
+		"run doquiet; " \
+		"run tryboot; " \
+	"fi; " \
+
+#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
+
+#define CONFIG_ARP_TIMEOUT	200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
+
+#define CONFIG_SYS_MAXARGS	48	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START       0x70000000
+#define CONFIG_SYS_MEMTEST_END         0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS	2
+#define PHYS_SDRAM_1			CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE		(gd->bd->bi_dram[0].size)
+#define PHYS_SDRAM_2			CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE		(gd->bd->bi_dram[1].size)
+#define PHYS_SDRAM_SIZE			(gd->ram_size)
+
+#define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE        (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_FSL_IIM
+
+#define CONFIG_SYS_I2C_SPEED	100000
+
+/* I2C1 */
+#define CONFIG_SYS_NUM_I2C_BUSES	9
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
+				}
+
+#define CONFIG_BCH
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+/* Backlight Control */
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66666000
+
+/* Framebuffer and LCD */
+#ifdef CONFIG_VIDEO
+	#define CONFIG_VIDEO_IPUV3
+#endif
+
+#endif				/* __CONFIG_H */