mpc83xx: Add support for MPC8349 esd caddy2

The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

changed to use mkconfig -t option instead, plus misc codingstyle fixes.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

1 files changed, 56 insertions, 42 deletions

diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index f9db73b2dc..dbc15b297f 100644
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -35,6 +35,13 @@
 #define __CONFIG_H
 
 /*
+ * Top level Makefile configuration choices
+ */
+#ifdef CONFIG_MK_caddy2
+#define VME_CADDY2
+#endif
+
+/*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
@@ -43,6 +50,8 @@
 #define CONFIG_MPC8349		1	/* MPC8349 specific */
 #define CONFIG_VME8349		1	/* ESD VME8349 board specific */
 
+#define CONFIG_MISC_INIT_R
+
 #define CONFIG_PCI
 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
@@ -75,7 +84,9 @@
  */
 #define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
-#undef CONFIG_SPD_EEPROM		/* dont use SPD EEPROM for DDR setup*/
+#define CONFIG_SPD_EEPROM
+#define SPD_EEPROM_ADDRESS		0x54
+#define CONFIG_SYS_READ_SPD		vme8349_read_spd
 #define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */
 
 /*
@@ -96,54 +107,40 @@
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 					 DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_SIZE		512	/* MB */
-
-#if (CONFIG_SYS_DDR_SIZE == 512)
-#define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10 | \
-					 CSCONFIG_BANK_BIT_3)
-#endif
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_SYS_DDR_TIMING_0	        0x00220802
-#define CONFIG_SYS_DDR_TIMING_1	        0x39377322
-#define CONFIG_SYS_DDR_TIMING_2	        0x2f9848ca	/* P9-45, tuning? */
-#define CONFIG_SYS_DDR_TIMING_3	        0x00000000
-#define CONFIG_SYS_DDR_CONTROL		0xc2000000	/* unbuf,no DYN_PWR */
-#define CONFIG_SYS_DDR_MODE		0x07940242
-#define CONFIG_SYS_DDR_MODE2		0x00000000
-/* autocharge,no open page */
-#define CONFIG_SYS_DDR_INTERVAL	        0x04060100
-#define CONFIG_SYS_DDR_SDRAM_CFG	0x63000000
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x04061000
+#define CONFIG_SYS_DDRCDR		0x80080001
 
 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER			        /* use the CFI driver */
-#define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE           128		/* flash size in MB */
-/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
+#ifdef VME_CADDY2
+#define CONFIG_SYS_FLASH_BASE		0xffc00000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		4		/* flash size in MB */
+#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
+					 (2 << BR_PS_SHIFT) |	/*  32bit */ \
+					 BR_V)			/* valid */
 
+#define CONFIG_SYS_OR0_PRELIM		0xffc06ff7	/*   4 MB flash size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000015	/*   4 MB window size */
+#else
+#define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */
 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | \
 					 (2 << BR_PS_SHIFT) |	/*  32bit */ \
 					 BR_V)			/* valid */
 
-#define CONFIG_SYS_OR0_PRELIM		0xF8006FF7	/* 128 MB flash size */
+#define CONFIG_SYS_OR0_PRELIM		0xf8006ff7	/* 128 MB flash size */
 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000001A	/* 128 MB window size */
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000001a	/* 128 MB window size */
+#endif
+/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
 
 #define CONFIG_SYS_BR1_PRELIM		(0xf0000000 | 0x00001801)
-#define CONFIG_SYS_OR1_PRELIM		(0xffff8000 | 0x00000200)
+#define CONFIG_SYS_OR1_PRELIM		(0xfffc0008 | 0x00000200)
 #define CONFIG_SYS_LBLAWBAR1_PRELIM	0xf0000000
-#define CONFIG_SYS_LBLAWAR1_PRELIM	(0x80000000 | 0x0000000e)
+#define CONFIG_SYS_LBLAWAR1_PRELIM	(0x80000000 | 0x00000011)
 
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/
@@ -157,7 +154,7 @@
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
-#undef  CONFIG_SYS_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
 #endif
 
 #define CONFIG_SYS_INIT_RAM_LOCK	1
@@ -174,11 +171,10 @@
 
 /*
  * Local Bus LCRR and LBCR regs
- *    LCRR:  DLL bypass, Clock divider is 4
+ *    LCRR:  no DLL bypass, Clock divider is 4
  * External Local Bus rate is
  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
  */
-#define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
 #define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
 #define CONFIG_SYS_LBC_LBCR	0x00000000
 
@@ -268,10 +264,10 @@
 #undef PCI_ONE_PCI1
 #endif
 
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
+#ifndef VME_CADDY2
 #define CONFIG_NET_MULTI
+#endif
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
@@ -282,19 +278,26 @@
 	#define PCI_IDSEL_NUMBER	0xFIXME
 #endif
 
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+
 #endif	/* CONFIG_PCI */
 
 /*
  * TSEC configuration
  */
+#ifdef VME_CADDY2
+#define CONFIG_E1000
+#else
 #define CONFIG_TSEC_ENET		/* TSEC ethernet support */
+#endif
 
 #if defined(CONFIG_TSEC_ENET)
 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI
 #endif
 
-#define CONFIG_GMII		       /* MII PHY management */
+#define CONFIG_GMII			/* MII PHY management */
 #define CONFIG_TSEC1
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2
@@ -312,6 +315,12 @@
 
 #endif	/* CONFIG_TSEC_ENET */
 
+#if defined(CONFIG_E1000)
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+#endif
+
 /*
  * Environment
  */
@@ -560,7 +569,7 @@
 #define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS			/* boot command will set bootargs */
 
-#define CONFIG_BAUDRATE	 115200
+#define CONFIG_BAUDRATE	 9600
 
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
@@ -605,4 +614,9 @@
 
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
+#ifndef __ASSEMBLY__
+int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
+		     unsigned char *buffer, int len);
+#endif
+
 #endif	/* __CONFIG_H */