mpc8260: remove ep8260 board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Frank Panno <fpanno@delphintech.com>

1 files changed, 0 insertions, 744 deletions

diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
deleted file mode 100644
index 9cd3054a15..0000000000
--- a/include/configs/ep8260.h
+++ /dev/null
@@ -1,744 +0,0 @@
-/*
- * (C) Copyright 2002
- * Frank Panno <fpanno@delphintech.com>, Delphin Technology AG
- *
- * This file is based on similar values for other boards found in other
- * U-Boot config files, and some that I found in the EP8260 manual.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- *
- * "EP8260 H, V.1.1"
- *	- 64M 60x Bus SDRAM
- *	- 32M Local Bus SDRAM
- *	- 16M Flash (4 x AM29DL323DB90WDI)
- *	- 128k NVRAM with RTC
- *
- * "EP8260 H2, V.1.3" (CONFIG_SYS_EP8260_H2)
- *	- 300MHz/133MHz/66MHz
- *	- 64M 60x Bus SDRAM
- *	- 32M Local Bus SDRAM
- *	- 32M Flash
- *	- 128k NVRAM with RTC
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Define this to enable support the EP8260 H2 version */
-#define CONFIG_SYS_EP8260_H2	1
-/* #undef CONFIG_SYS_EP8260_H2  */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN  (66 * 1000 * 1000)
-
-/*-----------------------------------------------------------------------
- * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
- *-----------------------------------------------------------------------
- * What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Here are some example values (all frequencies are in MHz):
- *
- * MODCK_H   MODCK[1-3]	 Osc	CPM    Core
- * -------   ----------	 ---	---    ----
- * 0x2	     0x2	 33	133    133
- * 0x2	     0x3	 33	133    166
- * 0x2	     0x4	 33	133    200
- * 0x2	     0x5	 33	133    233
- * 0x2	     0x6	 33	133    266
- *
- * 0x5	     0x5	 66	133    133
- * 0x5	     0x6	 66	133    166
- * 0x5	     0x7	 66	133    200 *
- * 0x6	     0x0	 66	133    233
- * 0x6	     0x1	 66	133    266
- * 0x6	     0x2	 66	133    300
- */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_SBC_MODCK_H  (HRCW_MODCK_H0110)
-#else
-#define CONFIG_SYS_SBC_MODCK_H  (HRCW_MODCK_H0110)
-#endif
-
-/* Define this if you want to boot from 0x00000100. If you don't define
- * this, you will need to program the bootloader to 0xfff00000, and
- * get the hardware reset config words at 0xfe000000. The simplest
- * way to do that is to program the bootloader at both addresses.
- * It is suggested that you just let U-Boot live at 0x00000000.
- */
-/* #define CONFIG_SYS_SBC_BOOT_LOW 1 */	/* only for HRCW */
-/* #undef CONFIG_SYS_SBC_BOOT_LOW */
-
-/* The reset command will not work as expected if the reset address does
- * not point to the correct address.
- */
-
-#define CONFIG_SYS_RESET_ADDRESS	0xFFF00100
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ep8260/config.mk
- * The main FLASH is whichever is connected to *CS0. U-Boot expects
- * this to be the SIMM.
- */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_FLASH0_BASE 0xFE000000
-#define CONFIG_SYS_FLASH0_SIZE 32
-#else
-#define CONFIG_SYS_FLASH0_BASE 0xFF000000
-#define CONFIG_SYS_FLASH0_SIZE 16
-#endif
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
- * want it enabled, don't define these constants.
- */
-#define CONFIG_SYS_FLASH1_BASE 0
-#define CONFIG_SYS_FLASH1_SIZE 0
-#undef CONFIG_SYS_FLASH1_BASE
-#undef CONFIG_SYS_FLASH1_SIZE
-
-/* What should be the base address of SDRAM DIMM (60x bus) and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/* define CONFIG_SYS_LSDRAM if you want to enable the 32M SDRAM on the
- * local bus (8260 local bus is NOT cacheable!)
-*/
-/* #define CONFIG_SYS_LSDRAM */
-#undef CONFIG_SYS_LSDRAM
-
-#ifdef CONFIG_SYS_LSDRAM
-/* What should be the base address of SDRAM DIMM (local bus) and how big is
- * it (in Mbytes)?
-*/
-  #define CONFIG_SYS_SDRAM1_BASE 0x04000000
-  #define CONFIG_SYS_SDRAM1_SIZE 32
-#else
-  #define CONFIG_SYS_SDRAM1_BASE 0
-  #define CONFIG_SYS_SDRAM1_SIZE 0
-  #undef CONFIG_SYS_SDRAM1_BASE
-  #undef CONFIG_SYS_SDRAM1_SIZE
-#endif /* CONFIG_SYS_LSDRAM */
-
-/* What should be the base address of NVRAM and how big is
- * it (in Bytes)
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR  0xFA080000
-#define CONFIG_SYS_NVRAM_SIZE       (128*1024)-16
-
-/* The RTC is a Dallas DS1556
- */
-#define CONFIG_RTC_DS1556
-
-/* What should be the base address of the LEDs and switch S0?
- * If you don't want them enabled, don't define this.
- */
-#define CONFIG_SYS_LED_BASE 0x00000000
-#undef CONFIG_SYS_LED_BASE
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC          /* define if console on SMC */
-#undef  CONFIG_CONS_ON_SCC          /* define if console on SCC */
-#undef  CONFIG_CONS_NONE            /* define if console on neither */
-#define CONFIG_CONS_INDEX    1      /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef  CONFIG_ETHER_ON_SCC           /* define if ethernet on SCC    */
-#define CONFIG_ETHER_ON_FCC           /* define if ethernet on FCC    */
-#undef  CONFIG_ETHER_NONE             /* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX      3     /* which SCC/FCC channel for ethernet */
-
-#if ( CONFIG_ETHER_INDEX == 3 )
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the local Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-
-/*
- * - RAM for BD/Buffers is on the local Bus (see 28-13)
- */
-#ifdef CONFIG_SYS_LSDRAM
-  #define CONFIG_SYS_CPMFCR_RAMTYPE	3
-#else /* CONFIG_SYS_LSDRAM */
-  #define CONFIG_SYS_CPMFCR_RAMTYPE	0
-#endif /* CONFIG_SYS_LSDRAM */
-
-/* - Enable Half Duplex in FSMR */
-/* # define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB) */
-# define CONFIG_SYS_FCC_PSMR		0
-
-#else /* CONFIG_ETHER_INDEX */
-# error "on EP8260 ethernet must be FCC3"
-#endif /* CONFIG_ETHER_INDEX */
-
-/*
- * select i2c support configuration
- *
- * Supported configurations are {none, software, hardware} drivers.
- * If the software driver is chosen, there are some additional
- * configuration items that the driver uses to drive the port pins.
- */
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* This is for HARD, must go */
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#ifdef CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
-#define I2C_READ	((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00010000; \
-			else    iop->pdat &= ~0x00010000
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
-			else    iop->pdat &= ~0x00020000
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SYS_I2C_SOFT */
-
-/* #define CONFIG_RTC_DS174x */
-
-/* Define this to reserve an entire FLASH sector (256 KB) for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* What should the console's baud rate be? */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_BAUDRATE         9600
-#else
-#define CONFIG_BAUDRATE         115200
-#endif
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR          00:10:EC:00:30:8C
-
-#define CONFIG_IPADDR		192.168.254.130
-#define CONFIG_SERVERIP         192.168.254.49
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY        -1
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt       */
-
-/* Define this variable to enable the "hush" shell (from
-   Busybox) as command line interpreter, thus enabling
-   powerful command line syntax like
-   if...then...else...fi conditionals or `&&' and '||'
-   constructs ("shell scripts").
-   If undefined, you get the old, much simpler behaviour
-   with a somewhat smapper memory footprint.
-*/
-#define CONFIG_SYS_HUSH_PARSER
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_CDP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_PORTIO
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-#undef CONFIG_CMD_XIMG
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR               0xF0000000
-#define CONFIG_SYS_DEFAULT_IMMR       0x00010000
-
-/* Where do the on board registers (CS4) live? */
-#define CONFIG_SYS_REGS_BASE          0xFA000000
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_EP8260           11      /* on an Embedded Planet EP8260 Board, Rev. 11 */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
-
-/*
- * Miscellaneous configurable options
- */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CBSIZE              1024       /* Console I/O Buffer Size      */
-#else
-#  define CONFIG_SYS_CBSIZE              256        /* Console I/O Buffer Size      */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE        (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS       8            /* max number of command args   */
-
-#define CONFIG_SYS_BARGSIZE      CONFIG_SYS_CBSIZE   /* Boot Argument Buffer Size    */
-
-#ifdef CONFIG_SYS_LSDRAM
-  #define CONFIG_SYS_MEMTEST_START 0x04000000   /* memtest works on  */
-  #define CONFIG_SYS_MEMTEST_END   0x06000000   /* 64-96 MB in SDRAM */
-#else
-  #define CONFIG_SYS_MEMTEST_START 0x00000000   /* memtest works on  */
-  #define CONFIG_SYS_MEMTEST_END   0x02000000   /* 0-32 MB in SDRAM */
-#endif /* CONFIG_SYS_LSDRAM */
-
-#define	CONFIG_CLOCKS_IN_MHZ	1      /* clocks passsed to Linux in MHz */
-
-#define CONFIG_SYS_LOAD_ADDR     0x00100000   /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE    CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_SDRAM_BASE    CONFIG_SYS_SDRAM0_BASE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
-#else
-#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (0x00000000)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-#ifdef CONFIG_SYS_EP8260_H2
-/* get the HRCW ISB field from CONFIG_SYS_DEFAULT_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_DEFAULT_IMMR & 0x10000000) >> 10) |\
-			    ((CONFIG_SYS_DEFAULT_IMMR & 0x01000000) >> 7)  |\
-			    ((CONFIG_SYS_DEFAULT_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM                |\
-			 HRCW_L2CPC01            |\
-			 CONFIG_SYS_SBC_HRCW_IMMR       |\
-			 HRCW_APPC10             |\
-			 HRCW_CS10PC01           |\
-			 CONFIG_SYS_SBC_MODCK_H	 |\
-			 CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
-#else
-#define CONFIG_SYS_HRCW_MASTER 0x10400245
-#endif
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE        0x4000  /* Size of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE          CONFIG_SYS_TEXT_BASE
-
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#  define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN      (256 << 10)     /* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN       (128 << 10)     /* Reserve 128 kB for malloc()  */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS   1       /* max number of memory banks         */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_MAX_FLASH_SECT    128      /* max number of sectors on one chip  */
-#else
-#define CONFIG_SYS_MAX_FLASH_SECT    71      /* max number of sectors on one chip  */
-#endif
-
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_FLASH_ERASE_TOUT  240000  /* Timeout for Flash Erase (in ms)    */
-#define CONFIG_SYS_FLASH_WRITE_TOUT  500     /* Timeout for Flash Write (in ms)    */
-#else
-#define CONFIG_SYS_FLASH_ERASE_TOUT  8000    /* Timeout for Flash Erase (in ms)    */
-#define CONFIG_SYS_FLASH_WRITE_TOUT  1       /* Timeout for Flash Write (in ms)    */
-#endif
-
-#ifndef CONFIG_SYS_RAMBOOT
-#  define CONFIG_ENV_IS_IN_FLASH  1
-
-#  ifdef CONFIG_ENV_IN_OWN_SECT
-#    define CONFIG_ENV_ADDR       (CONFIG_SYS_MONITOR_BASE + 0x40000)
-#    define CONFIG_ENV_SECT_SIZE  0x40000
-#  else
-#    define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-#    define CONFIG_ENV_SIZE       0x1000  /* Total Size of Environment Sector */
-#    define CONFIG_ENV_SECT_SIZE  0x10000 /* see README - env sect real size */
-#  endif /* CONFIG_ENV_IN_OWN_SECT */
-#else
-#  define CONFIG_ENV_IS_IN_NVRAM  1
-#  define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#  define CONFIG_ENV_SIZE         0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT     5     /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers                    2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT   (HID0_ICE  |\
-			 HID0_DCE  |\
-			 HID0_ICFI |\
-			 HID0_DCI  |\
-			 HID0_IFEM |\
-			 HID0_ABE)
-#ifdef CONFIG_SYS_LSDRAM
-/* 8260 local bus is NOT cacheable */
-#define CONFIG_SYS_HID0_FINAL  (/*HID0_ICE  |*/\
-			 HID0_IFEM |\
-			 HID0_ABE  |\
-			 HID0_EMCP)
-#else /* !CONFIG_SYS_LSDRAM */
-#define CONFIG_SYS_HID0_FINAL  (HID0_ICE  |\
-			 HID0_IFEM |\
-			 HID0_ABE  |\
-			 HID0_EMCP)
-#endif /* CONFIG_SYS_LSDRAM */
-
-#define CONFIG_SYS_HID2        0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR         0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration                                       4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR         (BCR_EBM   |\
-			 BCR_PLDP  |\
-			 BCR_EAV   |\
-			 BCR_NPQM0)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration                             4-31
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR      (SIUMCR_L2CPC01 |\
-			 SIUMCR_APPC10  |\
-			 SIUMCR_CS10PC01)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control                            11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#ifdef CONFIG_SYS_EP8260_H2
-/* TBD: Find out why setting the BMT to 0xff causes the FCC to
- * generate TX buffer underrun errors for large packets under
- * Linux
- */
-#define CONFIG_SYS_SYPCR_BMT	0x00000600
-#else
-#define CONFIG_SYS_SYPCR_BMT	SYPCR_BMT
-#endif
-
-#ifdef CONFIG_SYS_LSDRAM
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC |\
-			 CONFIG_SYS_SYPCR_BMT  |\
-			 SYPCR_PBME |\
-			 SYPCR_LBME |\
-			 SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC |\
-			 CONFIG_SYS_SYPCR_BMT  |\
-			 SYPCR_PBME |\
-			 SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC |\
-			 TMCNTSC_ALR |\
-			 TMCNTSC_TCF |\
-			 TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_PISCR       (PISCR_PS  |\
-			 PISCR_PTF |\
-			 PISCR_PTE)
-#else
-#define CONFIG_SYS_PISCR	0
-#endif
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control                                   9-8
- *-----------------------------------------------------------------------
- */
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_SCCR        (SCCR_DFBRG00)
-#else
-#define CONFIG_SYS_SCCR        (SCCR_DFBRG01)
-#endif
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-/*-----------------------------------------------------------------------
- * MPTPR - Memory Refresh Timer Prescale Register               10-32
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_MPTPR	(0x0A00 & MPTPR_PTP_MSK)
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM    64 bit  FLASH (BGA - 16MB AMD AM29DL323DB90WDI)
- *  1   60x     SDRAM   64 bit  SDRAM (BGA - 64MB Micron 48LC8M16A2TG)
- *  2   Local   SDRAM   32 bit  SDRAM (BGA - 32MB Micron 48LC8M16A2TG)
- *  3   unused
- *  4   60x     GPCM     8 bit  Board Regs, NVRTC
- *  5   unused
- *  6   unused
- *  7   unused
- *  8   PCMCIA
- *  9   unused
- * 10   unused
- * 11   unused
-*/
-
-/*-----------------------------------------------------------------------
- * BRx - Base Register
- *     Ref: Section 10.3.1 on page 10-14
- * ORx - Option Register
- *     Ref: Section 10.3.2 on page 10-18
- *-----------------------------------------------------------------------
- */
-
-/* Bank 0 - FLASH
- *
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64                      |\
-			 BRx_DECC_NONE                  |\
-			 BRx_MS_GPCM_P                  |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE)     |\
-			 ORxG_CSNT                      |\
-			 ORxG_ACS_DIV1                  |\
-			 ORxG_SCY_8_CLK                 |\
-			 ORxG_EHTR)
-
-/* Bank 1 - SDRAM
- * PSDRAM
- */
-#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE)     |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI1_A6             |\
-			 ORxS_NUMR_12)
-
-#ifdef CONFIG_SYS_EP8260_H2
-#define CONFIG_SYS_PSDMR       0xC34E246E
-#else
-#define CONFIG_SYS_PSDMR       0xC34E2462
-#endif
-
-#define CONFIG_SYS_PSRT	0x64
-
-#ifdef CONFIG_SYS_LSDRAM
-/* Bank 2 - SDRAM
- * LSDRAM
- */
-
-  #define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
-			   BRx_PS_32                      |\
-			   BRx_MS_SDRAM_L                 |\
-			   BRx_V)
-
-  #define CONFIG_SYS_OR2_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE)     |\
-			   ORxS_BPD_4                     |\
-			   ORxS_ROWST_PBI0_A9             |\
-			   ORxS_NUMR_12)
-
-  #define CONFIG_SYS_LSDMR      0x416A2562
-  #define CONFIG_SYS_LSRT	0x64
-#else
-  #define CONFIG_SYS_LSRT	0x0
-#endif /* CONFIG_SYS_LSDRAM */
-
-/* Bank 4 - On board registers
- * NVRTC and BCSR
- */
-#define CONFIG_SYS_BR4_PRELIM   ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK)  |\
-			   BRx_PS_8                     |\
-			   BRx_MS_GPCM_P                |\
-			   BRx_V)
-/*
-#define CONFIG_SYS_OR4_PRELIM    (ORxG_AM_MSK                 |\
-			   ORxG_CSNT                   |\
-			   ORxG_ACS_DIV1               |\
-			   ORxG_SCY_10_CLK              |\
-			   ORxG_TRLX)
-*/
-#define CONFIG_SYS_OR4_PRELIM 0xfff00854
-
-#ifdef _NOT_USED_SINCE_NOT_WORKING_
-/* Bank 8 - On board registers
- * PCMCIA (currently not working!)
- */
-#define CONFIG_SYS_BR8_PRELIM   ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK)  |\
-			   BRx_PS_16                     |\
-			   BRx_MS_GPCM_P                |\
-			   BRx_V)
-
-#define CONFIG_SYS_OR8_PRELIM    (ORxG_AM_MSK                 |\
-			   ORxG_CSNT                   |\
-			   ORxG_ACS_DIV1               |\
-			   ORxG_SETA                   |\
-			   ORxG_SCY_10_CLK)
-#endif
-
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition, whole device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		""
-#define MTDPARTS_DEFAULT	""
-*/
-
-#endif  /* __CONFIG_H */