arm: Remove wireless_space board

This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>

1 files changed, 0 insertions, 179 deletions

diff --git a/include/configs/wireless_space.h b/include/configs/wireless_space.h
deleted file mode 100644
index 191ac1b73f..0000000000
--- a/include/configs/wireless_space.h
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
- *
- * Based on the netspace_v2 code which is
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _CONFIG_WIRELESS_SPACE_H
-#define _CONFIG_WIRELESS_SPACE_H
-
-/*
- * Machine number definition
- */
-#define MACH_TYPE_WIRELESS_SPACE	2500 /* is missing in mach-types.h */
-#define CONFIG_MACH_TYPE		MACH_TYPE_WIRELESS_SPACE
-#define CONFIG_IDENT_STRING		" Wireless Space"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131		/* CPU Core subversion */
-/* SoC name */
-#define CONFIG_KW88F6281
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH		/* no NOR or SPI flash */
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_USB
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-#define CONFIG_NR_DRAM_BANKS		1
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_RBTREE
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-#define CONFIG_SYS_IDE_MAXBUS           1
-#define CONFIG_SYS_IDE_MAXDEVICE        1
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable only egiga0... */
-#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
-#define CONFIG_PHY_BASE_ADR 0xa		/* ... through a 'fake' PHY */
-#define CONFIG_MII
-#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_NETCONSOLE
-#define CONFIG_MV88E61XX_SWITCH
-#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
-#define CONFIG_MV88E61XX_CMD
-#define CONFIG_CMD_TFTPPUT
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1 /* 8-bit device address */
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-
-/*
- * File systems support
- */
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Console configuration
- */
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/*
- * Enable device tree support
- */
-#define CONFIG_OF_LIBFDT
-
-/*
- * Environment variables configurations
- */
-
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SECT_SIZE		0x20000	/* 128KB */
-#define CONFIG_ENV_SIZE			0x20000	/* 128KB */
-#define CONFIG_ENV_OFFSET		0x80000	/* env starts here */
-
-/*
- * Board-specific command to make using buttons etc easier
- */
-
-#define CONFIG_WIRELESS_SPACE_CMD
-
-/*
- * Default environment variables
- */
-#define CONFIG_PREBOOT
-
-#define CONFIG_BOOTARGS "console=ttyS0,115200"
-
-#define CONFIG_BOOTCOMMAND					\
-	"if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS				\
-	"stdin=serial\0"					\
-	"stdout=serial\0"					\
-	"stderr=serial\0"					\
-	"bootfile=uImage\0"					\
-	"loadaddr=0x800000\0"					\
-	"autoload=no\0"						\
-	"netconsole="						\
-		"set stdin $stdin,nc; "				\
-		"set stdout $stdout,nc; "			\
-		"set stderr $stderr,nc;\0"			\
-	"diskload=ide reset && "				\
-		"ext2load ide 0:1 $loadaddr /boot/$bootfile\0"	\
-	"usbload=usb start && "					\
-		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"	\
-	"preboot="						\
-		"dhcp && run netconsole\0"
-
-#endif /* _CONFIG_WIRELESS_SPACE_H */