Add support for UEC to 8568

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

1 files changed, 49 insertions, 7 deletions

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 5bc953adc4..dc9cb1ff54 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -28,20 +28,21 @@
 
 /* High Level Configuration Options */
 #define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500			1	/* BOOKE e500 family */
+#define CONFIG_E500		1	/* BOOKE e500 family */
 #define CONFIG_MPC85xx		1	/* MPC8540/60/55/41/48/68 */
 #define CONFIG_MPC8568		1	/* MPC8568 specific */
 #define CONFIG_MPC8568MDS	1	/* MPC8568MDS board specific */
 
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
+#undef CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 /*#define CONFIG_DDR_2T_TIMING		 Sets the 2T timing bit */
 
 /*#define CONFIG_DDR_ECC*/			/* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* 	 DDR controller or DMA? */
+/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/	/* DDR controller or DMA? */
 #define CONFIG_MEM_INIT_VALUE		0xDeadBeef
 
 
@@ -297,6 +298,7 @@ extern unsigned long get_clock_freq(void);
 
 #define OF_CPU			"PowerPC,8568@0"
 #define OF_SOC			"soc8568@e0000000"
+#define OF_QE			"qe@e0080000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
 #define OF_STDOUT_PATH		"/soc8568@e0000000/serial@4600"
 
@@ -311,7 +313,7 @@ extern unsigned long get_clock_freq(void);
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_EEPROM_ADDR	0x52
 #define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES        {0,0x69}	/* Don't probe these addrs */
+#define CFG_I2C_NOPROBES        {{0,0x69}}	/* Don't probe these addrs */
 #define CFG_I2C_OFFSET		0x3000
 #define CFG_I2C2_OFFSET		0x3100
 
@@ -340,6 +342,44 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
 
+#ifdef CONFIG_QE
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#ifndef CONFIG_TSEC_ENET
+#define CONFIG_ETHPRIME         "Freescale GETH"
+#endif
+#define CONFIG_PHY_MODE_NEED_CHANGE
+#define CONFIG_eTSEC_MDIO_BUS
+
+#ifdef CONFIG_eTSEC_MDIO_BUS
+#define CONFIG_MIIM_ADDRESS 	0xE0024520
+#endif
+
+#define CONFIG_UEC_ETH1         /* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM        0       /* UCC1 */
+#define CFG_UEC1_RX_CLK         QE_CLK_NONE
+#define CFG_UEC1_TX_CLK         QE_CLK16
+#define CFG_UEC1_ETH_TYPE       GIGA_ETH
+#define CFG_UEC1_PHY_ADDR       7
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2         /* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM        1       /* UCC2 */
+#define CFG_UEC2_RX_CLK         QE_CLK_NONE
+#define CFG_UEC2_TX_CLK         QE_CLK16
+#define CFG_UEC2_ETH_TYPE       GIGA_ETH
+#define CFG_UEC2_PHY_ADDR       1
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+#endif /* CONFIG_QE */
+
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -348,13 +388,12 @@ extern unsigned long get_clock_freq(void);
 
 #endif	/* CONFIG_PCI */
 
-
-#if defined(CONFIG_TSEC_ENET)
-
 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI 	1
 #endif
 
+#if defined(CONFIG_TSEC_ENET)
+
 #define CONFIG_MII		1	/* MII PHY management */
 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"eTSEC0"
@@ -460,12 +499,15 @@ extern unsigned long get_clock_freq(void);
  */
 
 /* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 #define CONFIG_HAS_ETH2
 #define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
 #define CONFIG_IPADDR    192.168.1.253