Add Altera Nios-II boards EP1C20, EP1S10 and EP1S40

Patch from Scott McNutt, 11 Aug 2005

3 files changed, 585 insertions, 0 deletions

diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h
new file mode 100644
index 0000000000..5507f352b9
--- /dev/null
+++ b/include/configs/EP1C20.h
@@ -0,0 +1,199 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*------------------------------------------------------------------------
+ * BOARD/CPU
+ *----------------------------------------------------------------------*/
+#define CONFIG_EP1C20		1		/* EP1C20 board		*/
+#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
+
+#define CFG_RESET_ADDR		0x00000000	/* Hard-reset address	*/
+#define CFG_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
+#define CFG_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* enable early board-spec. init*/
+
+/*------------------------------------------------------------------------
+ * CACHE -- the following will support II/s and II/f. The II/s does not
+ * have dcache, so the cache instructions will behave as NOPs.
+ *----------------------------------------------------------------------*/
+#define CFG_ICACHE_SIZE		4096		/* 4 KByte total	*/
+#define CFG_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
+#define CFG_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
+#define CFG_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
+
+/*------------------------------------------------------------------------
+ * MEMORY BASE ADDRESSES
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_BASE		0x00000000	/* FLASH base addr	*/
+#define CFG_FLASH_SIZE		0x00800000	/* 8 MByte		*/
+#define CFG_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
+#define CFG_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
+#define CFG_SRAM_BASE		0x02000000	/* SRAM base addr	*/
+#define CFG_SRAM_SIZE		0x00100000	/* 1 MB (only 1M mapped)*/
+
+/*------------------------------------------------------------------------
+ * MEMORY ORGANIZATION
+ *	-Monitor at top.
+ *	-The heap is placed below the monitor.
+ *	-Global data is placed below the heap.
+ *	-The stack is placed below global data (&grows down).
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 128k		*/
+#define CFG_GBL_DATA_SIZE	128		/* Global data size rsvd*/
+#define CFG_MALLOC_LEN		(CFG_ENV_SIZE + 128*1024)
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_OFFSET	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP		CFG_GBL_DATA_OFFSET
+
+/*------------------------------------------------------------------------
+ * FLASH (AM29LV065D)
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_SECT	128		/* Max # sects per bank */
+#define CFG_MAX_FLASH_BANKS	1		/* Max # of flash banks */
+#define CFG_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
+#define CFG_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
+#define CFG_FLASH_WORD_SIZE	unsigned char	/* flash word size	*/
+
+/*------------------------------------------------------------------------
+ * ENVIRONMENT -- Put environment in sector CFG_MONITOR_LEN above
+ * CFG_RESET_ADDR, since we assume the monitor is stored at the
+ * reset address, no? This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH	1		/* Environment in flash */
+#define CFG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
+#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
+#define CFG_ENV_ADDR	(CFG_RESET_ADDR + CFG_MONITOR_LEN)
+
+/*------------------------------------------------------------------------
+ * CONSOLE
+ *----------------------------------------------------------------------*/
+#if defined(CONFIG_CONSOLE_JTAG)
+#define CFG_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
+#else
+#define CFG_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
+#endif
+
+#define CFG_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
+#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
+#define CFG_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
+
+#define CFG_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
+
+/*------------------------------------------------------------------------
+ * EPCS Device -- wne CFG_NIOS_EPCSBASE is defined code/commands for
+ * epcs device access is enabled. The base address is the epcs
+ * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
+ * The register base is currently at offset 0x600 from the memory base.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_EPCSBASE	0x02100200	/* EPCS register base	*/
+
+/*------------------------------------------------------------------------
+ * DEBUG
+ *----------------------------------------------------------------------*/
+#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
+
+/*------------------------------------------------------------------------
+ * TIMEBASE --
+ *
+ * The high res timer defaults to 1 msec. Since it includes the period
+ * registers, we can slow it down to 10 msec using TMRCNT. If the default
+ * period is acceptable, TMRCNT can be left undefined.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
+#define CFG_NIOS_TMRIRQ		3		/* Timer IRQ num	*/
+#define CFG_NIOS_TMRMS		10		/* 10 msec per tick	*/
+#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
+#define CFG_HZ		(CONFIG_SYS_CLK_FREQ/(CFG_NIOS_TMRCNT + 1))
+
+/*------------------------------------------------------------------------
+ * STATUS LED -- Provides a simple blinking led. For Nios2 each board
+ * must implement its own led routines -- leds are, after all,
+ * board-specific, no?
+ *----------------------------------------------------------------------*/
+#define CFG_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
+#define CONFIG_STATUS_LED			/* Enable status driver */
+
+#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
+#define STATUS_LED_STATE	1		/* Blinking		*/
+#define STATUS_LED_PERIOD	(500/CFG_NIOS_TMRMS) /* Every 500 msec	*/
+
+/*------------------------------------------------------------------------
+ * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
+ * and really doesn't need any additional clutter. So I choose the lazy
+ * way out to avoid changes there -- define the base address to ensure
+ * cache bypass so there's no need to monkey with inx/outx macros.
+ *----------------------------------------------------------------------*/
+#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
+#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
+#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
+
+#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_IPADDR		192.168.2.21
+#define CONFIG_SERVERIP		192.168.2.16
+
+/*------------------------------------------------------------------------
+ * COMMANDS
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS		(CFG_CMD_BDI	| \
+				 CFG_CMD_DHCP	| \
+				 CFG_CMD_ECHO	| \
+				 CFG_CMD_ENV	| \
+				 CFG_CMD_FLASH	| \
+				 CFG_CMD_IMI	| \
+				 CFG_CMD_IRQ	| \
+				 CFG_CMD_LOADS	| \
+				 CFG_CMD_LOADB	| \
+				 CFG_CMD_MEMORY | \
+				 CFG_CMD_MISC	| \
+				 CFG_CMD_NET	| \
+				 CFG_CMD_PING	| \
+				 CFG_CMD_RUN	| \
+				 CFG_CMD_SAVES	)
+#include <cmd_confdefs.h>
+
+/*------------------------------------------------------------------------
+ * MISC
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP				/* Provide extended help*/
+#define CFG_PROMPT		"==> "		/* Command prompt	*/
+#define CFG_CBSIZE		256		/* Console I/O buf size */
+#define CFG_MAXARGS		16		/* Max command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot arg buf size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buf size */
+#define CFG_LOAD_ADDR		CFG_SDRAM_BASE	/* Default load address */
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE	/* Start addr for test	*/
+#define CFG_MEMTEST_END		CFG_INIT_SP - 0x00020000
+
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/EP1S10.h b/include/configs/EP1S10.h
new file mode 100644
index 0000000000..6eca9f23dc
--- /dev/null
+++ b/include/configs/EP1S10.h
@@ -0,0 +1,193 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*------------------------------------------------------------------------
+ * BOARD/CPU
+ *----------------------------------------------------------------------*/
+#define CONFIG_EP1S10		1		/* EP1S10 board		*/
+#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
+
+#define CFG_RESET_ADDR		0x00000000	/* Hard-reset address	*/
+#define CFG_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
+#define CFG_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
+
+/*------------------------------------------------------------------------
+ * CACHE -- the following will support II/s and II/f. The II/s does not
+ * have dcache, so the cache instructions will behave as NOPs.
+ *----------------------------------------------------------------------*/
+#define CFG_ICACHE_SIZE		4096		/* 4 KByte total	*/
+#define CFG_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
+#define CFG_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
+#define CFG_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
+
+/*------------------------------------------------------------------------
+ * MEMORY BASE ADDRESSES
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_BASE		0x00000000	/* FLASH base addr	*/
+#define CFG_FLASH_SIZE		0x00800000	/* 8 MByte		*/
+#define CFG_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
+#define CFG_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
+#define CFG_SRAM_BASE		0x02000000	/* SRAM base addr	*/
+#define CFG_SRAM_SIZE		0x00100000	/* 1 MB			*/
+
+/*------------------------------------------------------------------------
+ * MEMORY ORGANIZATION
+ *	-Monitor at top.
+ *	-The heap is placed below the monitor.
+ *	-Global data is placed below the heap.
+ *	-The stack is placed below global data (&grows down).
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256k		*/
+#define CFG_GBL_DATA_SIZE	128		/* Global data size rsvd*/
+#define CFG_MALLOC_LEN		(CFG_ENV_SIZE + 256*1024) /* 256k heap */
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_OFFSET	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP		CFG_GBL_DATA_OFFSET
+
+/*------------------------------------------------------------------------
+ * FLASH (AM29LV065D)
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_SECT	128		/* Max # sects per bank */
+#define CFG_MAX_FLASH_BANKS	1		/* Max # of flash banks */
+#define CFG_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
+#define CFG_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
+
+/*------------------------------------------------------------------------
+ * ENVIRONMENT -- Put environment in sector CFG_MONITOR_LEN above
+ * CFG_FLASH_BASE, since we assume that u-boot is stored at the bottom
+ * of flash memory. This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH	1		/* Environment in flash */
+#define CFG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
+#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
+#define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_MONITOR_LEN)
+
+/*------------------------------------------------------------------------
+ * CONSOLE
+ *----------------------------------------------------------------------*/
+#if defined(CONFIG_CONSOLE_JTAG)
+#define CFG_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
+#else
+#define CFG_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
+#endif
+
+#define CFG_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
+#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
+#define CFG_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
+
+#define CFG_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
+
+/*------------------------------------------------------------------------
+ * EPCS Device -- None for stratix.
+ *----------------------------------------------------------------------*/
+#undef CFG_NIOS_EPCSBASE
+
+/*------------------------------------------------------------------------
+ * DEBUG
+ *----------------------------------------------------------------------*/
+#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
+
+/*------------------------------------------------------------------------
+ * TIMEBASE --
+ *
+ * The high res timer defaults to 1 msec. Since it includes the period
+ * registers, we can slow it down to 10 msec using TMRCNT. If the default
+ * period is acceptable, TMRCNT can be left undefined.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
+#define CFG_NIOS_TMRIRQ		3		/* Timer IRQ num	*/
+#define CFG_NIOS_TMRMS		10		/* 10 msec per tick	*/
+#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
+#define CFG_HZ		(CONFIG_SYS_CLK_FREQ/(CFG_NIOS_TMRCNT + 1))
+
+/*------------------------------------------------------------------------
+ * STATUS LED -- Provides a simple blinking led. For Nios2 each board
+ * must implement its own led routines -- since leds are board-specific.
+ *----------------------------------------------------------------------*/
+#define CFG_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
+#define CONFIG_STATUS_LED			/* Enable status driver */
+
+#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
+#define STATUS_LED_STATE	1		/* Blinking		*/
+#define STATUS_LED_PERIOD	(500/CFG_NIOS_TMRMS) /* Every 500 msec	*/
+
+/*------------------------------------------------------------------------
+ * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
+ * and really doesn't need any additional clutter. So I choose the lazy
+ * way out to avoid changes there -- define the base address to ensure
+ * cache bypass so there's no need to monkey with inx/outx macros.
+ *----------------------------------------------------------------------*/
+#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
+#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
+#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
+
+#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_IPADDR		192.168.2.21
+#define CONFIG_SERVERIP		192.168.2.16
+
+/*------------------------------------------------------------------------
+ * COMMANDS
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS		(CFG_CMD_BDI	| \
+				 CFG_CMD_DHCP	| \
+				 CFG_CMD_ECHO	| \
+				 CFG_CMD_ENV	| \
+				 CFG_CMD_FLASH	| \
+				 CFG_CMD_IMI	| \
+				 CFG_CMD_IRQ	| \
+				 CFG_CMD_LOADS	| \
+				 CFG_CMD_LOADB	| \
+				 CFG_CMD_MEMORY | \
+				 CFG_CMD_MISC	| \
+				 CFG_CMD_NET	| \
+				 CFG_CMD_PING	| \
+				 CFG_CMD_RUN	| \
+				 CFG_CMD_SAVES	)
+#include <cmd_confdefs.h>
+
+/*------------------------------------------------------------------------
+ * MISC
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP				/* Provide extended help*/
+#define CFG_PROMPT		"==> "		/* Command prompt	*/
+#define CFG_CBSIZE		256		/* Console I/O buf size */
+#define CFG_MAXARGS		16		/* Max command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot arg buf size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buf size */
+#define CFG_LOAD_ADDR		CFG_SDRAM_BASE	/* Default load address */
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE	/* Start addr for test	*/
+#define CFG_MEMTEST_END		CFG_INIT_SP - 0x00020000
+
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/EP1S40.h b/include/configs/EP1S40.h
new file mode 100644
index 0000000000..976e79acb6
--- /dev/null
+++ b/include/configs/EP1S40.h
@@ -0,0 +1,193 @@
+/*
+ * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*------------------------------------------------------------------------
+ * BOARD/CPU
+ *----------------------------------------------------------------------*/
+#define CONFIG_EP1S40		1		/* EP1S40 board		*/
+#define CONFIG_SYS_CLK_FREQ	50000000	/* 50 MHz core clk	*/
+
+#define CFG_RESET_ADDR		0x00000000	/* Hard-reset address	*/
+#define CFG_EXCEPTION_ADDR	0x01000020	/* Exception entry point*/
+#define CFG_NIOS_SYSID_BASE	0x021208b8	/* System id address	*/
+
+/*------------------------------------------------------------------------
+ * CACHE -- the following will support II/s and II/f. The II/s does not
+ * have dcache, so the cache instructions will behave as NOPs.
+ *----------------------------------------------------------------------*/
+#define CFG_ICACHE_SIZE		4096		/* 4 KByte total	*/
+#define CFG_ICACHELINE_SIZE	32		/* 32 bytes/line	*/
+#define CFG_DCACHE_SIZE		2048		/* 2 KByte (II/f)	*/
+#define CFG_DCACHELINE_SIZE	4		/* 4 bytes/line (II/f)	*/
+
+/*------------------------------------------------------------------------
+ * MEMORY BASE ADDRESSES
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_BASE		0x00000000	/* FLASH base addr	*/
+#define CFG_FLASH_SIZE		0x00800000	/* 8 MByte		*/
+#define CFG_SDRAM_BASE		0x01000000	/* SDRAM base addr	*/
+#define CFG_SDRAM_SIZE		0x01000000	/* 16 MByte		*/
+#define CFG_SRAM_BASE		0x02000000	/* SRAM base addr	*/
+#define CFG_SRAM_SIZE		0x00100000	/* 1 MB			*/
+
+/*------------------------------------------------------------------------
+ * MEMORY ORGANIZATION
+ *	-Monitor at top.
+ *	-The heap is placed below the monitor.
+ *	-Global data is placed below the heap.
+ *	-The stack is placed below global data (&grows down).
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256k		*/
+#define CFG_GBL_DATA_SIZE	128		/* Global data size rsvd*/
+#define CFG_MALLOC_LEN		(CFG_ENV_SIZE + 256*1024) /* 256k heap */
+
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_OFFSET	(CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP		CFG_GBL_DATA_OFFSET
+
+/*------------------------------------------------------------------------
+ * FLASH (AM29LV065D)
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_FLASH_SECT	128		/* Max # sects per bank */
+#define CFG_MAX_FLASH_BANKS	1		/* Max # of flash banks */
+#define CFG_FLASH_ERASE_TOUT	8000		/* Erase timeout (msec) */
+#define CFG_FLASH_WRITE_TOUT	100		/* Write timeout (msec) */
+
+/*------------------------------------------------------------------------
+ * ENVIRONMENT -- Put environment in sector CFG_MONITOR_LEN above
+ * CFG_FLASH_BASE, since we assume that u-boot is stored at the bottom
+ * of flash memory. This will keep the environment in user region
+ * of flash. NOTE: the monitor length must be multiple of sector size
+ * (which is common practice).
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH	1		/* Environment in flash */
+#define CFG_ENV_SIZE		(64 * 1024)	/* 64 KByte (1 sector)	*/
+#define CONFIG_ENV_OVERWRITE			/* Serial change Ok	*/
+#define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_MONITOR_LEN)
+
+/*------------------------------------------------------------------------
+ * CONSOLE
+ *----------------------------------------------------------------------*/
+#if defined(CONFIG_CONSOLE_JTAG)
+#define CFG_NIOS_CONSOLE	0x021208b0	/* JTAG UART base addr	*/
+#else
+#define CFG_NIOS_CONSOLE	0x02120840	/* UART base addr	*/
+#endif
+
+#define CFG_NIOS_FIXEDBAUD	1		/* Baudrate is fixed	*/
+#define CONFIG_BAUDRATE		115200		/* Initial baudrate	*/
+#define CFG_BAUDRATE_TABLE	{115200}	/* It's fixed ;-)	*/
+
+#define CFG_CONSOLE_INFO_QUIET	1		/* Suppress console info*/
+
+/*------------------------------------------------------------------------
+ * EPCS Device -- None for stratix.
+ *----------------------------------------------------------------------*/
+#undef CFG_NIOS_EPCSBASE
+
+/*------------------------------------------------------------------------
+ * DEBUG
+ *----------------------------------------------------------------------*/
+#undef CONFIG_ROM_STUBS				/* Stubs not in ROM	*/
+
+/*------------------------------------------------------------------------
+ * TIMEBASE --
+ *
+ * The high res timer defaults to 1 msec. Since it includes the period
+ * registers, we can slow it down to 10 msec using TMRCNT. If the default
+ * period is acceptable, TMRCNT can be left undefined.
+ *----------------------------------------------------------------------*/
+#define CFG_NIOS_TMRBASE	0x02120820	/* Tick timer base addr */
+#define CFG_NIOS_TMRIRQ		3		/* Timer IRQ num	*/
+#define CFG_NIOS_TMRMS		10		/* 10 msec per tick	*/
+#define CFG_NIOS_TMRCNT (CFG_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
+#define CFG_HZ		(CONFIG_SYS_CLK_FREQ/(CFG_NIOS_TMRCNT + 1))
+
+/*------------------------------------------------------------------------
+ * STATUS LED -- Provides a simple blinking led. For Nios2 each board
+ * must implement its own led routines -- since leds are board-specific.
+ *----------------------------------------------------------------------*/
+#define CFG_LEDPIO_ADDR		0x02120870	/* LED PIO base addr	*/
+#define CONFIG_STATUS_LED			/* Enable status driver */
+
+#define STATUS_LED_BIT		1		/* Bit-0 on PIO		*/
+#define STATUS_LED_STATE	1		/* Blinking		*/
+#define STATUS_LED_PERIOD	(500/CFG_NIOS_TMRMS) /* Every 500 msec	*/
+
+/*------------------------------------------------------------------------
+ * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
+ * and really doesn't need any additional clutter. So I choose the lazy
+ * way out to avoid changes there -- define the base address to ensure
+ * cache bypass so there's no need to monkey with inx/outx macros.
+ *----------------------------------------------------------------------*/
+#define CONFIG_SMC91111_BASE	0x82110300	/* Base addr (bypass)	*/
+#define CONFIG_DRIVER_SMC91111			/* Using SMC91c111	*/
+#undef	CONFIG_SMC91111_EXT_PHY			/* Internal PHY		*/
+#define CONFIG_SMC_USE_32_BIT			/* 32-bit interface	*/
+
+#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_IPADDR		192.168.2.21
+#define CONFIG_SERVERIP		192.168.2.16
+
+/*------------------------------------------------------------------------
+ * COMMANDS
+ *----------------------------------------------------------------------*/
+#define CONFIG_COMMANDS		(CFG_CMD_BDI	| \
+				 CFG_CMD_DHCP	| \
+				 CFG_CMD_ECHO	| \
+				 CFG_CMD_ENV	| \
+				 CFG_CMD_FLASH	| \
+				 CFG_CMD_IMI	| \
+				 CFG_CMD_IRQ	| \
+				 CFG_CMD_LOADS	| \
+				 CFG_CMD_LOADB	| \
+				 CFG_CMD_MEMORY | \
+				 CFG_CMD_MISC	| \
+				 CFG_CMD_NET	| \
+				 CFG_CMD_PING	| \
+				 CFG_CMD_RUN	| \
+				 CFG_CMD_SAVES	)
+#include <cmd_confdefs.h>
+
+/*------------------------------------------------------------------------
+ * MISC
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP				/* Provide extended help*/
+#define CFG_PROMPT		"==> "		/* Command prompt	*/
+#define CFG_CBSIZE		256		/* Console I/O buf size */
+#define CFG_MAXARGS		16		/* Max command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot arg buf size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print buf size */
+#define CFG_LOAD_ADDR		CFG_SDRAM_BASE	/* Default load address */
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE	/* Start addr for test	*/
+#define CFG_MEMTEST_END		CFG_INIT_SP - 0x00020000
+
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+#endif	/* __CONFIG_H */