powerpc: mpc85xx: remove P2020DS board support

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

1 files changed, 0 insertions, 751 deletions

diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
deleted file mode 100644
index 820b6332a6..0000000000
--- a/include/configs/P2020DS.h
+++ /dev/null
@@ -1,751 +0,0 @@
-/*
- * Copyright 2007-2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * p2020ds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include "../board/freescale/common/ics307_clk.h"
-
-#ifdef CONFIG_36BIT
-#define CONFIG_PHYS_64BIT
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE		0xf8f40000
-#define CONFIG_RESET_VECTOR_ADDRESS	0xf8fffffc
-#endif
-
-#ifdef CONFIG_SPIFLASH
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE		0xf8f40000
-#define CONFIG_RESET_VECTOR_ADDRESS	0xf8fffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE		1	/* BOOKE */
-#define CONFIG_E500		1	/* BOOKE e500 family */
-#define CONFIG_P2020		1
-#define CONFIG_P2020DS		1
-#define CONFIG_MP		1	/* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-#define CONFIG_SYS_SRIO
-#define CONFIG_SRIO1			/* SRIO port 1 */
-#define CONFIG_SRIO2			/* SRIO port 2 */
-
-#define CONFIG_FSL_ELBC		1	/* Has Enhanced localbus controller */
-#define CONFIG_PCI		1	/* Enable PCI/PCIE */
-#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
-#define CONFIG_PCIE3		1	/* PCIE controler 3 (ULI bridge) */
-#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
-#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
-#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-
-#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
-#define CONFIG_E1000		1	/* Defind e1000 pci Ethernet card*/
-
-#define CONFIG_TSEC_ENET		/* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk() /* sysclk for MPC85xx */
-#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk() /* ddrclk for MPC85xx */
-#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-
-#define CONFIG_BOARD_EARLY_INIT_F	/* Call board_pre_init */
-
-#define CONFIG_ENABLE_36BIT_PHYS	1
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP			1
-#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
-#endif
-
-#define CONFIG_POST CONFIG_SYS_POST_MEMORY	/* test POST memory test */
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-#define CONFIG_PANIC_HANG	/* do not reset board on panic */
-
-/*
- * Config the L2 Cache
- */
-#define CONFIG_SYS_INIT_L2_ADDR		0xf8f80000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS	0xff8f80000ull
-#else
-#define CONFIG_SYS_INIT_L2_ADDR_PHYS	CONFIG_SYS_INIT_L2_ADDR
-#endif
-#define CONFIG_SYS_L2_SIZE		(512 << 10)
-#define CONFIG_SYS_INIT_L2_END	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
-
-#define CONFIG_SYS_CCSRBAR		0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_VERY_BIG_RAM
-#ifdef CONFIG_DDR2
-#define CONFIG_SYS_FSL_DDR2
-#else
-#define CONFIG_SYS_FSL_DDR3		1
-#endif
-
-/* ECC will be enabled based on perf_mode environment variable */
-/* #define	CONFIG_DDR_ECC */
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS	1
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	2
-
-/* I2C addresses of SPD EEPROMs */
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_SPD_BUS_NUM		0	/* SPD EEPROM located on I2C bus 0 */
-#define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
-
-/* These are used when DDR doesn't use SPD.  */
-#define CONFIG_SYS_SDRAM_SIZE		1024		/* DDR is 1GB */
-
-/* Default settings for "stable" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003F
-#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
-#define CONFIG_SYS_DDR_CS1_CONFIG	0x00000000
-#define CONFIG_SYS_DDR_TIMING_3		0x00020000
-#define CONFIG_SYS_DDR_TIMING_0		0x00330804
-#define CONFIG_SYS_DDR_TIMING_1		0x6f6b4846
-#define CONFIG_SYS_DDR_TIMING_2		0x0fa890d4
-#define CONFIG_SYS_DDR_MODE_1		0x00421422
-#define CONFIG_SYS_DDR_MODE_2		0x00000000
-#define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
-#define CONFIG_SYS_DDR_INTERVAL		0x61800100
-#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL		0x02000000
-#define CONFIG_SYS_DDR_TIMING_4		0x00220001
-#define CONFIG_SYS_DDR_TIMING_5		0x03402400
-#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8655A608
-#define CONFIG_SYS_DDR_CONTROL		0xE7000000 /* Type = DDR3: ECC enabled, No Interleaving */
-#define CONFIG_SYS_DDR_CONTROL2		0x24400011
-#define CONFIG_SYS_DDR_CDR1		0x00040000
-#define CONFIG_SYS_DDR_CDR2		0x00000000
-
-#define CONFIG_SYS_DDR_ERR_INT_EN	0x0000000d
-#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
-#define CONFIG_SYS_DDR_SBE		0x00010000
-
-/* Settings that differ for "performance" mode */
-#define CONFIG_SYS_DDR_CS0_BNDS_PERF		0x0000007F /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_BNDS_PERF		0x00000000 /* Interleaving Enabled */
-#define CONFIG_SYS_DDR_CS1_CONFIG_PERF	0x80014202
-#define CONFIG_SYS_DDR_TIMING_1_PERF		0x5d5b4543
-#define CONFIG_SYS_DDR_TIMING_2_PERF		0x0fa890ce
-#define CONFIG_SYS_DDR_CONTROL_PERF		0xC7004000 /* Type = DDR3: ECC disabled, cs0-cs1 interleaving */
-
-/*
- * The following set of values were tested for DDR2
- * with a DDR3 to DDR2 interposer
- *
-#define CONFIG_SYS_DDR_TIMING_3		0x00000000
-#define CONFIG_SYS_DDR_TIMING_0		0x00260802
-#define CONFIG_SYS_DDR_TIMING_1		0x3935d322
-#define CONFIG_SYS_DDR_TIMING_2		0x14904cc8
-#define CONFIG_SYS_DDR_MODE_1		0x00480432
-#define CONFIG_SYS_DDR_MODE_2		0x00000000
-#define CONFIG_SYS_DDR_INTERVAL		0x06180100
-#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
-#define CONFIG_SYS_DDR_CLK_CTRL		0x03800000
-#define CONFIG_SYS_DDR_OCD_CTRL		0x00000000
-#define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
-#define CONFIG_SYS_DDR_CONTROL		0xC3008000
-#define CONFIG_SYS_DDR_CONTROL2		0x04400010
- *
- */
-
-/*
- * Memory map
- *
- * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
- * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
- * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
- * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
- *
- * Localbus cacheable (TBD)
- * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
- *
- * Localbus non-cacheable
- * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
- * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
- * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
- * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
- * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
- * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_FLASH_BASE		0xe0000000	/* start of FLASH 128M */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
-#else
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-#endif
-
-#define CONFIG_FLASH_BR_PRELIM  \
-	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
-#define CONFIG_FLASH_OR_PRELIM	0xf8000ff7
-
-#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
-#define CONFIG_SYS_OR1_PRELIM	0xf8000ff7
-
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-
-#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
-
-#define CONFIG_HWCONFIG			/* enable hwconfig */
-#define CONFIG_FSL_NGPIXIS		/* use common ngPIXIS code */
-
-#ifdef CONFIG_FSL_NGPIXIS
-#define PIXIS_BASE	0xffdf0000	/* PIXIS registers */
-#ifdef CONFIG_PHYS_64BIT
-#define PIXIS_BASE_PHYS	0xfffdf0000ull
-#else
-#define PIXIS_BASE_PHYS	PIXIS_BASE
-#endif
-
-#define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR3_PRELIM		0xffffeff7	/* 32KB but only 4k mapped */
-
-#define PIXIS_LBMAP_SWITCH	7
-#define PIXIS_LBMAP_MASK	0xf0
-#define PIXIS_LBMAP_SHIFT	4
-#define PIXIS_LBMAP_ALTBANK	0x20
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
-	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
-	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000	/* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
-
-#define CONFIG_SYS_NAND_BASE		0xffa00000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
-#else
-#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
-#endif
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE,\
-				CONFIG_SYS_NAND_BASE + 0x40000, \
-				CONFIG_SYS_NAND_BASE + 0x80000,\
-				CONFIG_SYS_NAND_BASE + 0xC0000}
-#define CONFIG_SYS_MAX_NAND_DEVICE	4
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND			1
-#define CONFIG_NAND_FSL_ELBC		1
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000		/* length 256K */ \
-				| OR_FCM_PGS		/* Large Page*/ \
-				| OR_FCM_CSCT \
-				| OR_FCM_CST \
-				| OR_FCM_CHT \
-				| OR_FCM_SCY_1 \
-				| OR_FCM_TRLX \
-				| OR_FCM_EHTR)
-
-#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM  /* NOR Options */
-#define CONFIG_SYS_BR2_PRELIM  CONFIG_SYS_NAND_BR_PRELIM  /* NAND Base Address */
-#define CONFIG_SYS_OR2_PRELIM  CONFIG_SYS_NAND_OR_PRELIM  /* NAND Options */
-
-#define CONFIG_SYS_BR4_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR4_PRELIM  CONFIG_SYS_NAND_OR_PRELIM	/* NAND Options */
-#define CONFIG_SYS_BR5_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR5_PRELIM  CONFIG_SYS_NAND_OR_PRELIM	/* NAND Options */
-
-#define CONFIG_SYS_BR6_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \
-				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
-				| BR_PS_8		/* Port Size = 8bit */ \
-				| BR_MS_FCM		/* MSEL = FCM */ \
-				| BR_V)			/* valid */
-#define CONFIG_SYS_OR6_PRELIM  CONFIG_SYS_NAND_OR_PRELIM	/* NAND Options */
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-#define CONFIG_OF_STDOUT_VIA_ALIAS	1
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x29} }
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_ID_EEPROM
-#ifdef CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_BUS_NUM	0
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
-
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED		10000000
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 3, Slot 1, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME		"Slot 1"
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc00000000ull
-#else
-#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
-#endif
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xfffc00000ull
-#else
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
-#endif
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"ULI"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
-#else
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
-#endif
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, Slot 2, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc40000000ull
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc20000ull
-#else
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
-#endif
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-#if defined(CONFIG_PCI)
-
-/*PCIE video card used*/
-#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE1_IO_VIRT
-
-/* video */
-#undef CONFIG_VIDEO
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_BIOSEMU
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_ATI_RADEON_FB
-#define CONFIG_VIDEO_LOGO
-/*#define CONFIG_CONSOLE_CURSOR*/
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
-#endif
-
-/* SRIO1 uses the same window as PCIE2 mem window */
-#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
-#else
-#define CONFIG_SYS_SRIO1_MEM_PHYS	0xa0000000
-#endif
-#define CONFIG_SYS_SRIO1_MEM_SIZE	0x20000000	/* 512M */
-
-/* SRIO2 uses the same window as PCIE1 mem window */
-#define CONFIG_SYS_SRIO2_MEM_VIRT	0xc0000000
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc40000000ull
-#else
-#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc0000000
-#endif
-#define CONFIG_SYS_SRIO2_MEM_SIZE	0x20000000	/* 512M */
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SCSI_AHCI
-
-#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
-#define CONFIG_SATA_ULI5288
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
-#define CONFIG_SYS_SCSI_MAX_LUN	1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
-#endif /* SCSI */
-
-#endif	/* CONFIG_PCI */
-
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII		1	/* MII PHY management */
-#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"eTSEC1"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"eTSEC2"
-#define CONFIG_TSEC3	1
-#define CONFIG_TSEC3_NAME	"eTSEC3"
-
-#define CONFIG_FSL_SGMII_RISER	1
-#define SGMII_RISER_PHY_OFFSET	0x1b
-
-#ifdef CONFIG_FSL_SGMII_RISER
-#define CONFIG_SYS_TBIPA_VALUE		0x10 /* avoid conflict with eTSEC4 paddr */
-#endif
-
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC3_PHY_ADDR		2
-
-#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC3_PHYIDX		0
-
-#define CONFIG_ETHPRIME		"eTSEC1"
-
-#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#if defined(CONFIG_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_SYS_MMC_ENV_DEV		0
-#elif defined(CONFIG_SPIFLASH)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-#define CONFIG_ENV_SPI_MAX_HZ		10000000
-#define CONFIG_ENV_SPI_MODE		0
-#define CONFIG_ENV_SIZE			0x2000		/* 8KB */
-#define CONFIG_ENV_OFFSET		0x100000	/* 1MB */
-#define CONFIG_ENV_SECT_SIZE		0x10000
-#else
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SCSI
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#endif
-#endif
-
-/*
- * SDHC/MMC
- */
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH2
-#endif
-
-#define CONFIG_IPADDR		192.168.1.254
-
-#define CONFIG_HOSTNAME		unknown
-#define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
-
-#define CONFIG_SERVERIP		192.168.1.1
-#define CONFIG_GATEWAYIP	192.168.1.1
-#define CONFIG_NETMASK		255.255.255.0
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-
-#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
-
-#define CONFIG_BAUDRATE	115200
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-"perf_mode=performance\0"			\
-	"hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;"	\
-	"usb1:dr_mode=host,phy_type=ulpi\0"			\
-"netdev=eth0\0"						\
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
-"tftpflash=tftpboot $loadaddr $uboot; "			\
-	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
-	"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
-	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
-"satabootcmd=setenv bootargs root=/dev/$bdev rw "	\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"			\
-"consoledev=ttyS0\0"				\
-"ramdiskaddr=2000000\0"			\
-"ramdiskfile=p2020ds/ramdisk.uboot\0"		\
-"fdtaddr=c00000\0"				\
-"othbootargs=cache-sram-size=0x10000\0"	\
-"fdtfile=p2020ds/p2020ds.dtb\0"		\
-"bdev=sda3\0"					\
-"partition=scsi 0:0\0"
-
-#define CONFIG_HDBOOT				\
- "setenv bootargs root=/dev/$bdev rw "		\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "ext2load $partition $loadaddr $bootfile;"	\
- "ext2load $partition $fdtaddr $fdtfile;"	\
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND		\
- "setenv bootargs root=/dev/nfs rw "	\
- "nfsroot=$serverip:$rootpath "		\
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;"	\
- "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND		\
- "setenv bootargs root=/dev/ram rw "	\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "tftp $ramdiskaddr $ramdiskfile;"	\
- "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
-
-#endif	/* __CONFIG_H */