mpc83xx: add support for the MPC8323E RDB

MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial.  Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.

Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

1 files changed, 583 insertions, 0 deletions

diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
new file mode 100644
index 0000000000..376973b94d
--- /dev/null
+++ b/include/configs/MPC8323ERDB.h
@@ -0,0 +1,583 @@
+/*
+ * Copyright (C) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 family */
+#define CONFIG_QE		1	/* Has QE */
+#define CONFIG_MPC83XX		1	/* MPC83xx family */
+#define CONFIG_MPC832X		1	/* MPC832x CPU specific */
+
+#define CONFIG_PCI		1
+#define CONFIG_83XX_GENERIC_PCI	1
+
+/*
+ * System Clock Setup
+ */
+#define CONFIG_83XX_CLKIN	66666667	/* in Hz */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
+#endif
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CFG_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
+	HRCWL_DDR_TO_SCB_CLK_2X1 |\
+	HRCWL_VCO_1X2 |\
+	HRCWL_CSB_TO_CLKIN_2X1 |\
+	HRCWL_CORE_TO_CSB_2_5X1 |\
+	HRCWL_CE_PLL_VCO_DIV_2 |\
+	HRCWL_CE_PLL_DIV_1X1 |\
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CFG_HRCW_HIGH (\
+	HRCWH_PCI_HOST |\
+	HRCWH_PCI1_ARBITER_ENABLE |\
+	HRCWH_CORE_ENABLE |\
+	HRCWH_FROM_0X00000100 |\
+	HRCWH_BOOTSEQ_DISABLE |\
+	HRCWH_SW_WATCHDOG_DISABLE |\
+	HRCWH_ROM_LOC_LOCAL_16BIT |\
+	HRCWH_BIG_ENDIAN |\
+	HRCWH_LALE_NORMAL)
+
+/*
+ * System IO Config
+ */
+#define CFG_SICRL		0x00000000
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
+
+/*
+ * IMMR new address
+ */
+#define CFG_IMMR		0xE0000000
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_BASE		0x00000000	/* DDR is system memory */
+#define CFG_SDRAM_BASE		CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
+#define CFG_DDRCDR		0x73000002	/* DDR II voltage is 1.8V */
+
+#undef CONFIG_SPD_EEPROM
+#if defined(CONFIG_SPD_EEPROM)
+/* Determine DDR configuration from I2C interface
+ */
+#define SPD_EEPROM_ADDRESS	0x51	/* DDR SODIMM */
+#else
+/* Manually set up DDR parameters
+ */
+#define CFG_DDR_SIZE		64	/* MB */
+#define CFG_DDR_CS0_CONFIG	0x80840101
+#define CFG_DDR_TIMING_0	0x00220802
+#define CFG_DDR_TIMING_1	0x3935d322
+#define CFG_DDR_TIMING_2	0x0f9048ca
+#define CFG_DDR_TIMING_3	0x00000000
+#define CFG_DDR_CLK_CNTL	0x02000000
+#define CFG_DDR_MODE		0x44400232
+#define CFG_DDR_MODE2		0x8000c000
+#define CFG_DDR_INTERVAL	0x03200064
+#define CFG_DDR_CS0_BNDS	0x00000003
+#define CFG_DDR_SDRAM_CFG	0x43080000
+#define CFG_DDR_SDRAM_CFG2	0x00401000
+#endif
+
+/*
+ * Memory test
+ */
+#undef CFG_DRAM_TEST		/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00030000	/* memtest region */
+#define CFG_MEMTEST_END		0x03f00000
+
+/*
+ * The reserved memory
+ */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef  CFG_RAMBOOT
+#endif
+
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+
+/*
+ * Initial RAM Base Address Setup
+ */
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xE6000000	/* Initial RAM address */
+#define CFG_INIT_RAM_END	0x1000		/* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE	0x100		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_2)
+#define CFG_LBC_LBCR		0x00000000
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CFG_FLASH_CFI		/* use the Common Flash Interface */
+#define CFG_FLASH_CFI_DRIVER	/* use the CFI driver */
+#define CFG_FLASH_BASE		0xFE000000	/* FLASH base address */
+#define CFG_FLASH_SIZE		16	/* FLASH size is 16M */
+
+#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE	/* Window base at flash base */
+#define CFG_LBLAWAR0_PRELIM	0x80000018	/* 32MB window size */
+
+#define CFG_BR0_PRELIM	(CFG_FLASH_BASE |	/* Flash Base address */ \
+			(2 << BR_PS_SHIFT) |	/* 16 bit port size */ \
+			BR_V)			/* valid */
+#define CFG_OR0_PRELIM		0xfe006ff7	/* 16MB Flash size */
+
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
+#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+
+/*
+ * SDRAM on the Local Bus
+ */
+#undef CFG_LB_SDRAM		/* The board has not SRDAM on local bus */
+
+#ifdef CFG_LB_SDRAM
+#define CFG_LBC_SDRAM_BASE	0xF0000000	/* SDRAM base address */
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+
+#define CFG_LBLAWBAR2_PRELIM	CFG_LBC_SDRAM_BASE
+#define CFG_LBLAWAR2_PRELIM	0x80000019	/* 64MB */
+
+/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ *    port size = 32-bits = BR2[19:20] = 11
+ *    no parity checking = BR2[21:22] = 00
+ *    SDRAM for MSEL = BR2[24:26] = 011
+ *    Valid = BR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM	0xf0001861	/*Port size=32bit, MSEL=SDRAM */
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ *    64MB mask for AM, OR2[0:7] = 1111 1100
+ *                 XAM, OR2[17:18] = 11
+ *    9 columns OR2[19-21] = 010
+ *    13 rows   OR2[23-25] = 100
+ *    EAD set for extra time OR[31] = 1
+ *
+ * 0    4    8    12   16   20   24   28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
+#define CFG_OR2_PRELIM	0xfc006901
+
+#define CFG_LBC_LSRT	0x32000000	/* LB sdram refresh timer, about 6us */
+#define CFG_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON	0x0063b723
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_NORMAL)
+
+#endif
+
+/*
+ * Windows to access PIB via local bus
+ */
+#define CFG_LBLAWBAR3_PRELIM	0xf8008000	/* windows base 0xf8008000 */
+#define CFG_LBLAWAR3_PRELIM	0x8000000f	/* windows size 64KB */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX	1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2	(CFG_IMMR+0x4600)
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+#define OF_CPU			"PowerPC,8323@0"
+#define OF_SOC			"soc8323@e0000000"
+#define OF_QE			"qe@e0100000"
+#define OF_TBCLK		(bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH		"/soc8323@e0000000/serial@4500"
+
+/* I2C */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE	0x7F
+#define CFG_I2C_NOPROBES	{0x51}	/* Don't probe these addrs */
+#define CFG_I2C_OFFSET	0x3000
+
+/*
+ * Config on-board RTC
+ */
+#define CONFIG_RTC_DS1374		/* use ds1374 rtc via i2c */
+#define CFG_I2C_RTC_ADDR	0x68	/* at address 0x68 */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_MMIO_BASE	0x90000000
+#define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
+#define CFG_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CFG_PCI1_IO_BASE		0xd0000000
+#define CFG_PCI1_IO_PHYS		CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE		0x04000000	/* 64M */
+
+#ifdef CONFIG_PCI
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME		"Freescale GETH"
+
+#define CONFIG_UEC_ETH1		/* ETH3 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM	2	/* UCC3 */
+#define CFG_UEC1_RX_CLK		QE_CLK9
+#define CFG_UEC1_TX_CLK		QE_CLK10
+#define CFG_UEC1_ETH_TYPE	FAST_ETH
+#define CFG_UEC1_PHY_ADDR	4
+#define CFG_UEC1_INTERFACE_MODE	ENET_100_MII
+#endif
+
+#define CONFIG_UEC_ETH2		/* ETH4 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM	1	/* UCC2 */
+#define CFG_UEC2_RX_CLK		QE_CLK16
+#define CFG_UEC2_TX_CLK		QE_CLK3
+#define CFG_UEC2_ETH_TYPE	FAST_ETH
+#define CFG_UEC2_PHY_ADDR	0
+#define CFG_UEC2_INTERFACE_MODE	ENET_100_MII
+#endif
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+	#define CFG_ENV_IS_IN_FLASH	1
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x40000)
+	#define CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+	#define CFG_ENV_SIZE		0x2000
+#else
+	#define CFG_NO_FLASH		1	/* Flash is not usable now */
+	#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+	#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ASKENV
+
+#if defined(CONFIG_PCI)
+	#define CONFIG_CMD_PCI
+#endif
+#if defined(CFG_RAMBOOT)
+	#undef CONFIG_CMD_ENV
+	#undef CONFIG_CMD_LOADS
+#endif
+
+#undef CONFIG_WATCHDOG		/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP		/* undef to save memory */
+#define CFG_LOAD_ADDR		0x2000000	/* default load address */
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt */
+
+#if (CONFIG_CMD_KGDB)
+	#define CFG_CBSIZE	1024	/* Console I/O Buffer Size */
+#else
+	#define CFG_CBSIZE	256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*
+ * Core HID Setup
+ */
+#define CFG_HID0_INIT		0x000000000
+#define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
+#define CFG_HID2		HID2_HBE
+
+/*
+ * Cache Config
+ */
+#define CFG_DCACHE_SIZE		16384
+#define CFG_CACHELINE_SIZE	32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value */
+#endif
+
+/*
+ * MMU Setup
+ */
+
+/* DDR: cache cacheable */
+#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT0L	CFG_IBAT0L
+#define CFG_DBAT0U	CFG_IBAT0U
+
+/* IMMRBAR & PCI IO: cache-inhibit and guarded */
+#define CFG_IBAT1L	(CFG_IMMR | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT1U	(CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_DBAT1L	CFG_IBAT1L
+#define CFG_DBAT1U	CFG_IBAT1U
+
+/* FLASH: icache cacheable, but dcache-inhibit and guarded */
+#define CFG_IBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT2U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_DBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U	CFG_IBAT2U
+
+#define CFG_IBAT3L	(0)
+#define CFG_IBAT3U	(0)
+#define CFG_DBAT3L	CFG_IBAT3L
+#define CFG_DBAT3U	CFG_IBAT3U
+
+/* Stack in dcache: cacheable, no memory coherence */
+#define CFG_IBAT4L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
+#define CFG_IBAT4U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_DBAT4L	CFG_IBAT4L
+#define CFG_DBAT4U	CFG_IBAT4U
+
+#ifdef CONFIG_PCI
+/* PCI MEM space: cacheable */
+#define CFG_IBAT5L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT5U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+/* PCI MMIO space: cache-inhibit and guarded */
+#define CFG_IBAT6L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
+			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_IBAT6U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#else
+#define CFG_IBAT5L	(0)
+#define CFG_IBAT5U	(0)
+#define CFG_IBAT6L	(0)
+#define CFG_IBAT6U	(0)
+#define CFG_DBAT5L	CFG_IBAT5L
+#define CFG_DBAT5U	CFG_IBAT5U
+#define CFG_DBAT6L	CFG_IBAT6L
+#define CFG_DBAT6U	CFG_IBAT6U
+#endif
+
+/* Nothing in BAT7 */
+#define CFG_IBAT7L	(0)
+#define CFG_IBAT7U	(0)
+#define CFG_DBAT7L	CFG_IBAT7L
+#define CFG_DBAT7U	CFG_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+
+#if (CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ETHADDR	00:04:9f:ef:03:01
+#define CONFIG_HAS_ETH1				/* add support for "eth1addr" */
+#define CONFIG_ETH1ADDR	00:04:9f:ef:03:02
+
+#define CONFIG_IPADDR		10.0.0.2
+#define CONFIG_SERVERIP		10.0.0.1
+#define CONFIG_GATEWAYIP	10.0.0.1
+#define CONFIG_NETMASK		255.0.0.0
+#define CONFIG_NETDEV		eth1
+
+#define CONFIG_HOSTNAME		mpc8323erdb
+#define CONFIG_ROOTPATH		/nfsroot
+#define CONFIG_RAMDISKFILE	rootfs.ext2.gz.uboot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+#define CONFIG_FDTFILE		mpc832x_rdb.dtb
+
+#define CONFIG_LOADADDR		200000	/* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY	-1	/* -1 disables auto-boot */
+#define CONFIG_BAUDRATE		115200
+
+#define XMK_STR(x)	#x
+#define MK_STR(x)	XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" MK_STR(CONFIG_NETDEV) "\0"				\
+	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
+	"tftpflash=tftp $loadaddr $uboot;"				\
+		"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+		"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+		"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+	"fdtaddr=400000\0"						\
+	"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"				\
+	"ramdiskaddr=1000000\0"						\
+	"ramdiskfile=" MK_STR(CONFIG_RAMDISKFILE) "\0"			\
+	"console=ttyS0\0"						\
+	"setbootargs=setenv bootargs "					\
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
+	"setipargs=setenv bootargs nfsroot=$serverip:$rootpath "	\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+		"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setbootargs;"						\
+	"run setipargs;"						\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv rootdev /dev/ram;"					\
+	"run setbootargs;"						\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif	/* __CONFIG_H */