ppx4xx: remove APC405 board

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

1 files changed, 0 insertions, 424 deletions

diff --git a/include/configs/APC405.h b/include/configs/APC405.h
deleted file mode 100644
index 2678f50bbb..0000000000
--- a/include/configs/APC405.h
+++ /dev/null
@@ -1,424 +0,0 @@
-/*
- * (C) Copyright 2005-2008
- * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
- *
- * (C) Copyright 2001-2004
- * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_APCG405		1	/* ...on a APC405 board		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF80000
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
-#define CONFIG_BOARD_EARLY_INIT_R 1
-#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
-
-#define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_BOOTDELAY	1	/* autoboot after 3 seconds	*/
-#define CONFIG_BOOTCOUNT_LIMIT	1
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_SYS_USB_LOAD_COMMAND	"fatload usb 0 200000 pImage;"		\
-				"fatload usb 0 300000 pImage.initrd"
-#define CONFIG_SYS_USB_SELF_COMMAND	"usb start;run usb_load;usb stop;"	\
-				"run ramargs addip addcon usbargs;"	\
-				"bootm 200000 300000"
-#define CONFIG_SYS_USB_ARGS		"setenv bootargs $(bootargs) usbboot=1"
-#define CONFIG_SYS_BOOTLIMIT		"3"
-#define CONFIG_SYS_ALT_BOOTCOMMAND	"run usb_self;reset"
-
-#define CONFIG_EXTRA_ENV_SETTINGS                                       \
-	"hostname=abg405\0"                                             \
-	"bd_type=abg405\0"                                              \
-	"serial#=AA0000\0"                                              \
-	"kernel_addr=fe000000\0"                                        \
-	"ramdisk_addr=fe100000\0"                                       \
-	"ramargs=setenv bootargs root=/dev/ram rw\0"                    \
-	"nfsargs=setenv bootargs root=/dev/nfs rw "                     \
-	"nfsroot=$(serverip):$(rootpath)\0"				\
-	"addip=setenv bootargs $(bootargs) "                            \
-		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
-		":$(hostname)::off panic=1\0"				\
-	"addcon=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)"  \
-		" $(optargs)\0"                                         \
-	"flash_self=run ramargs addip addcon;"                          \
-		"bootm $(kernel_addr) $(ramdisk_addr)\0"                \
-	"net_nfs=tftp 200000 $(img);run nfsargs addip addcon;"          \
-		"bootm\0"                                               \
-	"rootpath=/tftpboot/abg405/target_root\0"                       \
-	"img=/tftpboot/abg405/pImage\0"                                 \
-	"load=tftp 100000 /tftpboot/abg405/u-boot.bin\0"		\
-	"update=protect off fff80000 ffffffff;era fff80000 ffffffff;"   \
-		"cp.b 100000 fff80000 80000\0"                          \
-	"ipaddr=10.0.111.111\0"                                         \
-	"netmask=255.255.0.0\0"                                         \
-	"serverip=10.0.0.190\0"						\
-	"splashimage=ffe80000\0"                                        \
-	"usb_load="CONFIG_SYS_USB_LOAD_COMMAND"\0"				\
-	"usb_self="CONFIG_SYS_USB_SELF_COMMAND"\0"				\
-	"usbargs="CONFIG_SYS_USB_ARGS"\0"					\
-	"bootlimit="CONFIG_SYS_BOOTLIMIT"\0"					\
-	"altbootcmd="CONFIG_SYS_ALT_BOOTCOMMAND"\0"				\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self;reset"
-
-#define CONFIG_ETHADDR		00:02:27:8e:00:00
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#undef  CONFIG_HAS_ETH1
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_LXT971_NO_SLEEP	1
-#define CONFIG_RESET_PHY_R	1	/* use reset_phy() */
-
-#define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SOURCE
-#define CONFIG_CMD_USB
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SUPPORT_VFAT
-
-#define CONFIG_AUTO_UPDATE	1	/* autoupdate via CF or USB */
-
-#undef  CONFIG_WATCHDOG			/* watchdog disabled */
-
-#define CONFIG_RTC_MC146818		/* DS1685 is MC146818 compatible*/
-#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
-
-#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory */
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_CONS_INDEX	1	/* Use UART0			*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-#define CONFIG_SYS_EXT_SERIAL_CLOCK    14745600 /* use external serial clock   */
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE      \
-	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
-	 57600, 115200, 230400, 460800, 921600 }
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO	1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-
-/* Only interrupt boot if space is pressed */
-/* If a long serial cable is connected but */
-/* other end is dead, garbage will be read */
-#define CONFIG_AUTOBOOT_KEYED	1
-#define CONFIG_AUTOBOOT_PROMPT	\
-	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
-#undef CONFIG_AUTOBOOT_DELAY_STR
-#define CONFIG_AUTOBOOT_STOP_STR " "
-
-#define CONFIG_VERSION_VARIABLE	1	/* include version env variable */
-
-#define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
-
-/*
- * PCI stuff
- */
-#define PCI_HOST_ADAPTER	0	/* configure as pci adapter     */
-#define PCI_HOST_FORCE		1	/* configure as pci host        */
-#define PCI_HOST_AUTO		2	/* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support          */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup  */
-#define CONFIG_PCI_SKIP_HOST_BRIDGE 1
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CONFIG_SYS_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
-
-/*
- * IDE/ATA stuff
- */
-#undef  CONFIG_IDE_8xx_DIRECT		/* no pcmcia interface required */
-#undef  CONFIG_IDE_LED			/* no led for ide supported */
-#define CONFIG_IDE_RESET	1	/* reset for ide supported */
-
-#define CONFIG_SYS_IDE_MAXBUS		1		/* max. 1 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS) /* max. 1 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR	0xF0100000
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MONITOR_BASE	0xFFF80000
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(2*1024*1024)	/* Reserve 2MB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Init. Memory map for Linux */
-
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2
-#define CONFIG_SYS_FLASH_QUIET_TEST	1
-#define CONFIG_SYS_FLASH_INCREMENT	0x01000000
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware protection */
-#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { \
-				{0xfe000000, 0x500000}, \
-				{0xffe80000, 0x180000} \
-				}
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster) */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ \
-				CONFIG_SYS_FLASH_BASE, \
-				CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT \
-				}
-#define CONFIG_SYS_FLASH_EMPTY_INFO	/* print 'E' for empty sector on flinfo */
-
-/*
- * Environment Variable setup
- */
-#define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CONFIG_ENV_OFFSET		0x000	/* environment starts at the */
-					/* beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
-#define CONFIG_ENV_OVERWRITE	1	/* allow overwriting vendor vars */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xF0000500	/* NVRAM base address */
-#define CONFIG_SYS_NVRAM_SIZE		242		/* NVRAM size */
-
-/*
- * I2C EEPROM (CAT24WC16) for environment
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address */
-/* mask of address bits that overflow into the "EEPROM chip address" */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has */
-					/* 16 byte page write mode using*/
-					/* last	4 bits of the address */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10 /* and takes up to 10 msec */
-
-/*
- * External Bus Controller (EBC) Setup
- */
-#define FLASH0_BA       (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_INCREMENT) /* FLASH 0 BA */
-#define FLASH1_BA       CONFIG_SYS_FLASH_BASE      /* FLASH 1 Base Address          */
-#define CAN_BA          0xF0000000          /* CAN Base Address              */
-#define DUART0_BA       0xF0000400          /* DUART Base Address            */
-#define DUART1_BA       0xF0000408          /* DUART Base Address            */
-#define RTC_BA          0xF0000500          /* RTC Base Address              */
-#define PS2_BA          0xF0000600          /* PS/2 Base Address             */
-#define CF_BA           0xF0100000          /* CompactFlash Base Address     */
-#define FPGA_BA         0xF0100100          /* FPGA internal Base Address    */
-#define FUJI_BA         0xF0100200          /* Fuji internal Base Address    */
-#define PCMCIA1_BA      0x20000000          /* PCMCIA Slot 1 Base Address    */
-#define PCMCIA2_BA      0x28000000          /* PCMCIA Slot 2 Base Address    */
-#define VGA_BA          0xF1000000          /* Epson VGA Base Address        */
-
-#define CONFIG_SYS_FPGA_BASE_ADDR      FPGA_BA     /* FPGA internal Base Address    */
-
-/* Memory Bank 0 (Flash Bank 0) initialization                               */
-#define CONFIG_SYS_EBC_PB0AP   0x92015480
-#define CONFIG_SYS_EBC_PB0CR   FLASH0_BA | 0x9A000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=16bit*/
-#define CONFIG_SYS_EBC_PB0AP_HWREV8 CONFIG_SYS_EBC_PB0AP
-#define CONFIG_SYS_EBC_PB0CR_HWREV8 FLASH1_BA | 0xBA000 /* BS=32MB */
-
-/* Memory Bank 1 (Flash Bank 1) initialization                               */
-#define CONFIG_SYS_EBC_PB1AP   0x92015480
-#define CONFIG_SYS_EBC_PB1CR   FLASH1_BA | 0x9A000 /* BAS=0xFE0,BS=16MB,BU=R/W,BW=16bit*/
-
-/* Memory Bank 2 (CAN0, 1, RTC, Duart) initialization                           */
-#define CONFIG_SYS_EBC_PB2AP   0x010053C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB2CR   CAN_BA | 0x18000    /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-
-/* Memory Bank 3 (CompactFlash IDE, FPGA internal) initialization               */
-#define CONFIG_SYS_EBC_PB3AP   0x010059C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB3CR   CF_BA | 0x1A000     /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 4 (PCMCIA Slot 1) initialization                                 */
-#define CONFIG_SYS_EBC_PB4AP   0x050007C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB4CR   PCMCIA1_BA | 0xFA000 /*BAS=0x200,BS=128MB,BU=R/W,BW=16bit*/
-
-/* Memory Bank 5 (Epson VGA) initialization                                     */
-#define CONFIG_SYS_EBC_PB5AP   0x03805380   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
-#define CONFIG_SYS_EBC_PB5CR   VGA_BA | 0x5A000    /* BAS=0xF10,BS=4MB,BU=R/W,BW=16bit */
-
-/* Memory Bank 6 (PCMCIA Slot 2) initialization                                 */
-#define CONFIG_SYS_EBC_PB6AP   0x050007C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CONFIG_SYS_EBC_PB6CR   PCMCIA2_BA | 0xFA000 /*BAS=0x280,BS=128MB,BU=R/W,BW=16bit*/
-
-/*
- * FPGA stuff
- */
-
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_CTRL           0x008
-#define CONFIG_SYS_FPGA_CTRL2          0x00a
-
-/* FPGA Control Reg */
-#define CONFIG_SYS_FPGA_CTRL_CF_RESET  0x0001
-#define CONFIG_SYS_FPGA_CTRL_WDI       0x0002
-#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
-
-#define CONFIG_SYS_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CONFIG_SYS_FPGA_MAX_SIZE       80*1024     /* 80kByte is enough for XC2S50  */
-
-/* FPGA program pin configuration */
-#define CONFIG_SYS_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CONFIG_SYS_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CONFIG_SYS_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CONFIG_SYS_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CONFIG_SYS_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
-
-/*
- * LCD Setup
- */
-#define CONFIG_SYS_LCD_BIG_MEM		(VGA_BA + 0x200000) /* S1D13806 Mem Base */
-#define CONFIG_SYS_LCD_BIG_REG		VGA_BA /* S1D13806 Reg Base */
-
-#define CONFIG_LCD_BIG		2 /* Epson S1D13806 used */
-
-/* Image information... */
-#define CONFIG_LCD_USED		CONFIG_LCD_BIG
-
-#define CONFIG_SYS_LCD_MEM		CONFIG_SYS_LCD_BIG_MEM
-#define CONFIG_SYS_LCD_REG		CONFIG_SYS_LCD_BIG_REG
-
-#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (1 << 20)
-
-/*
- * Definitions for initial stack pointer and data area (in data cache)
- */
-
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CONFIG_SYS_TEMP_STACK_OCM	1
-
-/* On Chip Memory location */
-#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
-
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-/* reserve some memory for BOOT limit info */
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - 16)
-
-#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */
-#define CONFIG_SYS_BOOTCOUNT_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 8)
-#endif
-
-/*
- * PCI OHCI controller
- */
-#define CONFIG_USB_OHCI_NEW	1
-#define CONFIG_PCI_OHCI		1
-#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
-#define CONFIG_USB_STORAGE	1
-#define CONFIG_SYS_USB_OHCI_BOARD_INIT 1
-
-#endif /* __CONFIG_H */