arm: socfpga: Clean up SoCFPGA configuration

Reorganize and cleanup the configuration file for SoCFPGA. There
is no functional change after this cleanup. This was necessary,
since the file was a wild mess and it was impossible to make sense
of it's content, let alone change something without breaking some
other thing. This patch puts the contents on par with regular U-Boot
standards.

Also remove unused preprocessor symbols CONFIG_SINGLE_BOOTOADER
and CONFIG_USE_IRQ, which is undefined by default. Finally, do
logical reordering of the defines in the file so it's much more
readable. The reordering was also necessary for the splitting
as the initial one was messy.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

1 files changed, 187 insertions, 218 deletions

diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h
index ac08e7ac8c..5349a359f6 100644
--- a/include/configs/socfpga_cyclone5.h
+++ b/include/configs/socfpga_cyclone5.h
@@ -1,319 +1,288 @@
 /*
- *  Copyright (C) 2012 Altera Corporation <www.altera.com>
+ * Copyright (C) 2012 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
-#ifndef __CONFIG_H
-#define __CONFIG_H
+#ifndef __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__
+#define __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__
 
 #include <asm/arch/socfpga_base_addrs.h>
 #include "../../board/altera/socfpga/pinmux_config.h"
 #include "../../board/altera/socfpga/iocsr_config.h"
 #include "../../board/altera/socfpga/pll_config.h"
 
-/*
- * High level configuration
- */
+#define CONFIG_SYS_GENERIC_BOARD
+
 /* Virtual target or real hardware */
 #undef CONFIG_SOCFPGA_VIRTUAL_TARGET
 
 #define CONFIG_ARMV7
-#undef CONFIG_USE_IRQ
+#define CONFIG_SYS_THUMB_BUILD
 
-#define CONFIG_MISC_INIT_R
-#define CONFIG_SINGLE_BOOTLOADER
 #define CONFIG_SOCFPGA
-#define CONFIG_CLOCKS
 
-#define CONFIG_SYS_ARM_CACHE_WRITEALLOC
-#define CONFIG_SYS_CACHELINE_SIZE	32
-#define CONFIG_SYS_L2_PL310
-#define CONFIG_SYS_PL310_BASE		SOCFPGA_MPUL2_ADDRESS
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+#define CONFIG_HW_WATCHDOG
 
-/* base address for .text section */
-#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_SYS_TEXT_BASE		0x08000040
-#else
-#define CONFIG_SYS_TEXT_BASE		0x01000040
-#endif
-#define CONFIG_SYS_LOAD_ADDR		0x7fc0
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
 
-/* Console I/O Buffer Size */
-#define CONFIG_SYS_CBSIZE		256
-/* Monitor Command Prompt */
-#define CONFIG_SYS_PROMPT		"SOCFPGA_CYCLONE5 # "
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_REGEX			/* Enable regular expression support */
 
 /*
- * Display CPU and Board Info
+ * High level configuration
  */
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
-
-/*
- * Enable early stage initialization at C environment
- */
 #define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MISC_INIT_R
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_CLOCKS
 
-/* flat device tree */
+#define CONFIG_FIT
 #define CONFIG_OF_LIBFDT
-/* skip updating the FDT blob */
-#define CONFIG_FDT_BLOB_SKIP_UPDATE
-/* Initial Memory map size for Linux, minus 4k alignment for DFT blob */
-#define CONFIG_SYS_BOOTMAPSZ		((256*1024*1024) - (4*1024))
+#define CONFIG_SYS_BOOTMAPSZ		(64 * 1024 * 1024)
 
-#define CONFIG_SPL_RAM_DEVICE
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start))
-#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start)
+#define CONFIG_TIMESTAMP		/* Print image info with timestamp */
 
 /*
- * Memory allocation (MALLOC)
+ * Memory configurations
  */
-/* Room required on the stack for the environment data */
-#define CONFIG_ENV_SIZE			1024
-/* Size of DRAM reserved for malloc() use */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 128*1024)
+#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on SoCDK */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM_1			0x0
+#define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1_SIZE
 
-/* SP location before relocation, must use scratch RAM */
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFFFF0000
-/* Reserving 0x100 space at back of scratch RAM for debug info */
 #define CONFIG_SYS_INIT_RAM_SIZE	(0x10000 - 0x100)
-/* Stack pointer prior relocation, must situated at on-chip RAM */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
-					 CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_SYS_NO_FLASH
-#include <config_cmd_default.h>
-/* FAT file system support */
-#define CONFIG_CMD_FAT
-/* bootz command support */
-#define CONFIG_CMD_BOOTZ
+#define CONFIG_SYS_INIT_SP_ADDR					\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE -	\
+	GENERATED_GBL_DATA_SIZE)
 
-
-/*
- * Misc
- */
-#define CONFIG_DOS_PARTITION            1
-
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_PARTITIONS
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
+#define CONFIG_SYS_TEXT_BASE		0x08000040
+#else
+#define CONFIG_SYS_TEXT_BASE		0x01000040
 #endif
 
-/*
- * Environment setup
- */
-
-/* Delay before automatically booting the default image */
-#define CONFIG_BOOTDELAY		3
-/* Enable auto completion of commands using TAB */
-#define CONFIG_AUTO_COMPLETE
-/* use "hush" command parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#define CONFIG_CMD_RUN
-
+/* Booting Linux */
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_BOOTFILE		"zImage"
+#define CONFIG_BOOTARGS		"console=ttyS0" __stringify(CONFIG_BAUDRATE)
 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTCOMMAND	"run ramboot"
 #else
-#define CONFIG_BOOTCOMMAND "run mmcload; run mmcboot"
+#define CONFIG_BOOTCOMMAND	"run mmcload; run mmcboot"
 #endif
+#define CONFIG_LOADADDR		0x8000
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
 
 /*
- * arguments passed to the bootm command. The value of
- * CONFIG_BOOTARGS goes into the environment value "bootargs".
- * Do note the value will overide also the chosen node in FDT blob.
+ * U-Boot general configurations
  */
-#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"verify=n\0" \
-	"loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
-	"ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
-		"bootm ${loadaddr} - ${fdt_addr}\0" \
-	"bootimage=zImage\0" \
-	"fdt_addr=100\0" \
-	"fdtimage=socfpga.dtb\0" \
-		"fsloadcmd=ext2load\0" \
-	"bootm ${loadaddr} - ${fdt_addr}\0" \
-	"mmcroot=/dev/mmcblk0p2\0" \
-	"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
-		" root=${mmcroot} rw rootwait;" \
-		"bootz ${loadaddr} - ${fdt_addr}\0" \
-	"mmcload=mmc rescan;" \
-		"fatload mmc 0:1 ${loadaddr} ${bootimage};" \
-		"fatload mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
-	"qspiroot=/dev/mtdblock0\0" \
-	"qspirootfstype=jffs2\0" \
-	"qspiboot=setenv bootargs " CONFIG_BOOTARGS \
-		" root=${qspiroot} rw rootfstype=${qspirootfstype};"\
-		"bootm ${loadaddr} - ${fdt_addr}\0"
-
-/* using environment setting for stdin, stdout, stderr */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-/* Enable the call to overwrite_console() */
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-/* Enable overwrite of previous console environment settings */
-#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
-
-/* max number of command args	 */
-#define CONFIG_SYS_MAXARGS		16
-
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
+#define CONFIG_SYS_PBSIZE	\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+						/* Print buffer size */
+#define CONFIG_SYS_MAXARGS	32		/* Max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+						/* Boot argument buffer size */
+#define CONFIG_VERSION_VARIABLE			/* U-BOOT version */
+#define CONFIG_AUTO_COMPLETE			/* Command auto complete */
+#define CONFIG_CMDLINE_EDITING			/* Command history etc */
+#define CONFIG_SYS_HUSH_PARSER
 
 /*
- * Hardware drivers
+ * Cache
  */
+#define CONFIG_SYS_ARM_CACHE_WRITEALLOC
+#define CONFIG_SYS_CACHELINE_SIZE 32
+#define CONFIG_SYS_L2_PL310
+#define CONFIG_SYS_PL310_BASE		SOCFPGA_MPUL2_ADDRESS
 
 /*
- * SDRAM Memory Map
+ * Ethernet on SoC (EMAC)
  */
-/* We have 1 bank of DRAM */
-#define CONFIG_NR_DRAM_BANKS		1
-/* SDRAM Bank #1 */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-/* SDRAM memory size */
-#define PHYS_SDRAM_1_SIZE		0x40000000
+#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET)
+#define CONFIG_DESIGNWARE_ETH
+#define CONFIG_NET_MULTI
+#define CONFIG_DW_ALTDESCRIPTOR
+#define CONFIG_MII
+#define CONFIG_AUTONEG_TIMEOUT		(15 * CONFIG_SYS_HZ)
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_GIGE
 
-#define PHYS_SDRAM_1			CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_START	0x00000000
-#define CONFIG_SYS_MEMTEST_END		PHYS_SDRAM_1_SIZE
+#define CONFIG_EMAC_BASE		SOCFPGA_EMAC0_ADDRESS
+#define CONFIG_PHY_INTERFACE_MODE	PHY_INTERFACE_MODE_RGMII
+#define CONFIG_EPHY0_PHY_ADDR		0
+
+/* PHY */
+#define CONFIG_EPHY1_PHY_ADDR		4
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+#define CONFIG_KSZ9021_CLK_SKEW_ENV	"micrel-ksz9021-clk-skew"
+#define CONFIG_KSZ9021_CLK_SKEW_VAL	0xf0f0
+#define CONFIG_KSZ9021_DATA_SKEW_ENV	"micrel-ksz9021-data-skew"
+#define CONFIG_KSZ9021_DATA_SKEW_VAL	0x0
 
-/*
- * NS16550 Configuration
- */
-#define UART0_BASE			SOCFPGA_UART0_ADDRESS
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	-4
-#define CONFIG_SYS_NS16550_CLK          V_NS16550_CLK
-#define CONFIG_CONS_INDEX               1
-#define CONFIG_SYS_NS16550_COM1		UART0_BASE
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200}
-#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define V_NS16550_CLK			1000000
-#else
-#define V_NS16550_CLK			100000000
 #endif
-#define CONFIG_BAUDRATE			115200
 
 /*
- * FLASH
+ * FPGA Driver
  */
-#define CONFIG_SYS_NO_FLASH
+#ifdef CONFIG_CMD_FPGA
+#define CONFIG_FPGA
+#define CONFIG_FPGA_ALTERA
+#define CONFIG_FPGA_SOCFPGA
+#define CONFIG_FPGA_COUNT		1
+#endif
 
 /*
  * L4 OSC1 Timer 0
  */
-/* This timer use eosc1 where the clock frequency is fixed
- * throughout any condition */
+/* This timer uses eosc1, whose clock frequency is fixed at any condition. */
 #define CONFIG_SYS_TIMERBASE		SOCFPGA_OSC1TIMER0_ADDRESS
-/* Timer info */
+#define CONFIG_SYS_TIMER_COUNTS_DOWN
+#define CONFIG_SYS_TIMER_COUNTER	(CONFIG_SYS_TIMERBASE + 0x4)
 #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
 #define CONFIG_SYS_TIMER_RATE		2400000
 #else
 #define CONFIG_SYS_TIMER_RATE		25000000
 #endif
-#define CONFIG_SYS_TIMER_COUNTS_DOWN
-#define CONFIG_SYS_TIMER_COUNTER	(CONFIG_SYS_TIMERBASE + 0x4)
-
-#define CONFIG_ENV_IS_NOWHERE
-
-/*
- * network support
- */
-#ifndef CONFIG_SOCFPGA_VIRTUAL_TARGET
-#define CONFIG_DESIGNWARE_ETH          1
-#endif
-
-#ifdef CONFIG_DESIGNWARE_ETH
-#define CONFIG_EMAC0_BASE              SOCFPGA_EMAC0_ADDRESS
-#define CONFIG_EMAC1_BASE              SOCFPGA_EMAC1_ADDRESS
-/* console support for network */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-/* designware */
-#define CONFIG_NET_MULTI
-#define CONFIG_DW_ALTDESCRIPTOR
-#define CONFIG_MII
-#define CONFIG_PHY_GIGE
-#define CONFIG_DW_AUTONEG
-#define CONFIG_AUTONEG_TIMEOUT         (15 * CONFIG_SYS_HZ)
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_MICREL
-#define CONFIG_PHY_MICREL_KSZ9021
-/* EMAC controller and PHY used */
-#define CONFIG_EMAC_BASE               CONFIG_EMAC1_BASE
-#define CONFIG_EPHY_PHY_ADDR           CONFIG_EPHY1_PHY_ADDR
-#define CONFIG_PHY_INTERFACE_MODE      PHY_INTERFACE_MODE_RGMII
-#endif /* CONFIG_DESIGNWARE_ETH */
 
 /*
  * L4 Watchdog
  */
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_HW_WATCHDOG_TIMEOUT_MS	2000
+#ifdef CONFIG_HW_WATCHDOG
 #define CONFIG_DESIGNWARE_WATCHDOG
 #define CONFIG_DW_WDT_BASE		SOCFPGA_L4WD0_ADDRESS
-/* Clocks source frequency to watchdog timer */
 #define CONFIG_DW_WDT_CLOCK_KHZ		25000
+#define CONFIG_HW_WATCHDOG_TIMEOUT_MS	12000
+#endif
 
 /*
- * MMC support
+ * MMC Driver
  */
+#ifdef CONFIG_CMD_MMC
 #define CONFIG_MMC
-#ifdef CONFIG_MMC
 #define CONFIG_BOUNCE_BUFFER
-#define CONFIG_CMD_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_DWMMC
 #define CONFIG_SOCFPGA_DWMMC
 #define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH	1024
 #define CONFIG_SOCFPGA_DWMMC_DRVSEL	3
 #define CONFIG_SOCFPGA_DWMMC_SMPSEL	0
+/* FIXME */
 /* using smaller max blk cnt to avoid flooding the limited stack we have */
-#define CONFIG_SYS_MMC_MAX_BLK_COUNT     256
-#endif	/* CONFIG_MMC */
+#define CONFIG_SYS_MMC_MAX_BLK_COUNT	256	/* FIXME -- SPL only? */
+#endif
 
 /*
- * SPL "Second Program Loader" aka Initial Software
+ * Serial Driver
  */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	-4
+#define CONFIG_SYS_NS16550_COM1		SOCFPGA_UART0_ADDRESS
+#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
+#define CONFIG_SYS_NS16550_CLK		1000000
+#else
+#define CONFIG_SYS_NS16550_CLK		100000000
+#endif
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
 
-/* Enable building of SPL globally */
-#define CONFIG_SPL_FRAMEWORK
-
-/* TEXT_BASE for linking the SPL binary */
-#define CONFIG_SPL_TEXT_BASE		0xFFFF0000
+/*
+ * USB
+ * Ungate USB:
+ * mw 0xffd05014 0x01bef032
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_DWC2_OTG
+/*#define CONFIG_USB_DWC2_REG_ADDR 0xffb00000*/
+#define CONFIG_USB_DWC2_REG_ADDR 0xffb40000
+#define CONFIG_USB_STORAGE
+#endif
 
-/* Stack size for SPL */
-#define CONFIG_SPL_STACK_SIZE		(4 * 1024)
+/*
+ * U-Boot environment
+ */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE			4096
+#define CONFIG_HOSTNAME			socfpga_cyclone5
 
-/* MALLOC size for SPL */
-#define CONFIG_SPL_MALLOC_SIZE		(5 * 1024)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"verify=n\0" \
+	"loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+	"ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
+		"bootm ${loadaddr} - ${fdt_addr}\0" \
+	"bootimage=zImage\0" \
+	"fdt_addr=100\0" \
+	"fdtimage=socfpga.dtb\0" \
+		"fsloadcmd=ext2load\0" \
+	"bootm ${loadaddr} - ${fdt_addr}\0" \
+	"mmcroot=/dev/mmcblk0p2\0" \
+	"mmcboot=setenv bootargs " CONFIG_BOOTARGS \
+		" root=${mmcroot} rw rootwait;" \
+		"bootz ${loadaddr} - ${fdt_addr}\0" \
+	"mmcload=mmc rescan;" \
+		"fatload mmc 0:1 ${loadaddr} ${bootimage};" \
+		"fatload mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
+	"qspiroot=/dev/mtdblock0\0" \
+	"qspirootfstype=jffs2\0" \
+	"qspiboot=setenv bootargs " CONFIG_BOOTARGS \
+		" root=${qspiroot} rw rootfstype=${qspirootfstype};"\
+		"bootm ${loadaddr} - ${fdt_addr}\0"
 
-#define CONFIG_SPL_SERIAL_SUPPORT
+/*
+ * SPL
+ */
+#define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_RAM_DEVICE
+#define CONFIG_SPL_TEXT_BASE		0xFFFF0000
+#define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
+#define CONFIG_SPL_STACK_SIZE		(4 * 1024)
+#define CONFIG_SPL_MALLOC_SIZE		(5 * 1024)	/* FIXME */
+#define CONFIG_SYS_SPL_MALLOC_START	((unsigned long) (&__malloc_start))
+#define CONFIG_SYS_SPL_MALLOC_SIZE	(&__malloc_end - &__malloc_start)
 
-#define CHUNKSZ_CRC32			(1 * 1024)
-
+#define CHUNKSZ_CRC32			(1 * 1024)	/* FIXME: ewww */
 #define CONFIG_CRC32_VERIFY
 
 /* Linker script for SPL */
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/armv7/socfpga/u-boot-spl.lds"
 
-/* Support for common/libcommon.o in SPL binary */
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
-/* Support for lib/libgeneric.o in SPL binary */
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
-
-/* Support for watchdog */
 #define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_PARTITIONS
+#endif
 
-#endif	/* __CONFIG_H */
+#endif	/* __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ */