configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignment

To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option,
which is deprecated, use the CONFIG_XXXX_BOOT options to
indicate the boot media, and the SoC is selected by the board.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

11 files changed, 59 insertions, 93 deletions

diff --git a/include/configs/at91-sama5_common.h b/include/configs/at91-sama5_common.h
index 435c7dfa8e..dc36c2ae6c 100644
--- a/include/configs/at91-sama5_common.h
+++ b/include/configs/at91-sama5_common.h
@@ -42,7 +42,7 @@
  * Command line configuration.
  */
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 
 #ifdef CONFIG_ENV_IS_IN_MMC
 /* Use raw reserved sectors to save environment */
@@ -63,7 +63,7 @@
 
 #else
 
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
 /* u-boot env in nand flash */
 #define CONFIG_ENV_OFFSET		0xc0000
 #define CONFIG_ENV_OFFSET_REDUND	0x100000
@@ -71,7 +71,7 @@
 #define CONFIG_BOOTCOMMAND		"nand read 0x21000000 0x180000 0x80000;"	\
 					"nand read 0x22000000 0x200000 0x600000;"	\
 					"bootz 0x22000000 - 0x21000000"
-#elif CONFIG_SYS_USE_SERIALFLASH
+#elif CONFIG_SPI_BOOT
 /* u-boot env in serial flash, by default is bus 0 and cs 0 */
 #define CONFIG_ENV_OFFSET		0x6000
 #define CONFIG_ENV_SIZE			0x2000
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index 36acaa5506..2957da9432 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -80,7 +80,7 @@
 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END		0x23e00000
 
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
 /* bootstrap + u-boot + env in nandflash */
 #define CONFIG_ENV_OFFSET		0x120000
 #define CONFIG_ENV_OFFSET_REDUND	0x100000
@@ -89,7 +89,7 @@
 #define CONFIG_BOOTCOMMAND						\
 	"nand read 0x70000000 0x200000 0x300000;"			\
 	"bootm 0x70000000"
-#elif CONFIG_SYS_USE_MMC
+#elif CONFIG_SD_BOOT
 /* bootstrap + u-boot + env + linux in mmc */
 #define CONFIG_ENV_SIZE		0x4000
 
@@ -115,7 +115,7 @@
 
 #define CONFIG_SYS_MONITOR_LEN		0x80000
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 
 #define CONFIG_SPL_BSS_START_ADDR	0x70000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
@@ -125,7 +125,7 @@
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_ECC
diff --git a/include/configs/at91sam9n12ek.h b/include/configs/at91sam9n12ek.h
index c9adcf9754..111a7dce7d 100644
--- a/include/configs/at91sam9n12ek.h
+++ b/include/configs/at91sam9n12ek.h
@@ -108,7 +108,7 @@
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	1
 #endif
 
-#ifdef CONFIG_SYS_USE_SPIFLASH
+#ifdef CONFIG_SPI_BOOT
 
 /* bootstrap + u-boot + env + linux in dataflash on CS0 */
 #define CONFIG_ENV_OFFSET		0x5000
@@ -119,7 +119,7 @@
 	"sf probe 0; sf read 0x22000000 0x100000 0x300000; "		\
 	"bootm 0x22000000"
 
-#elif defined(CONFIG_SYS_USE_NANDFLASH)
+#elif defined(CONFIG_NAND_BOOT)
 
 /* bootstrap + u-boot + env + linux in nandflash */
 #define CONFIG_ENV_OFFSET		0x120000
@@ -131,7 +131,7 @@
 	"nand read 0x22000000 0x200000 0x400000;"			\
 	"bootm 0x22000000 - 0x21000000"
 
-#else /* CONFIG_SYS_USE_MMC */
+#else /* CONFIG_SD_BOOT */
 
 /* bootstrap + u-boot + env + linux in mmc */
 
@@ -180,13 +180,19 @@
 #define CONFIG_SYS_MCKR			0x1301
 #define CONFIG_SYS_MCKR_CSS		0x1302
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
 #elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8400
+
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	0x800
@@ -196,10 +202,4 @@
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
-#elif CONFIG_SYS_USE_SPIFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8400
-
-#endif
-
 #endif
diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h
index eb798442ca..1d4971c59f 100644
--- a/include/configs/at91sam9x5ek.h
+++ b/include/configs/at91sam9x5ek.h
@@ -15,8 +15,6 @@
 #define CONFIG_SYS_AT91_SLOW_CLOCK	32768
 #define CONFIG_SYS_AT91_MAIN_CLOCK	12000000	/* 12 MHz crystal */
 
-#define CONFIG_AT91SAM9X5EK
-
 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
@@ -102,7 +100,7 @@
 #define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
 #define CONFIG_SYS_MEMTEST_END		0x26e00000
 
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
 /* bootstrap + u-boot + env + linux in nandflash */
 #define CONFIG_ENV_OFFSET		0x120000
 #define CONFIG_ENV_OFFSET_REDUND	0x100000
@@ -110,7 +108,7 @@
 #define CONFIG_BOOTCOMMAND	"nand read " \
 				"0x22000000 0x200000 0x300000; " \
 				"bootm 0x22000000"
-#elif defined(CONFIG_SYS_USE_SPIFLASH)
+#elif defined(CONFIG_SPI_BOOT)
 /* bootstrap + u-boot + env + linux in spi flash */
 #define CONFIG_ENV_OFFSET	0x5000
 #define CONFIG_ENV_SIZE		0x3000
@@ -128,7 +126,7 @@
 #define CONFIG_BOOTCOMMAND	"sf probe 0; " \
 				"sf read 0x22000000 0x84000 0x294000; " \
 				"bootm 0x22000000"
-#else /* CONFIG_SYS_USE_MMC */
+#else /* CONFIG_SD_BOOT */
 /* bootstrap + u-boot + env + linux in mmc */
 #define CONFIG_ENV_SIZE		0x4000
 #endif
@@ -160,13 +158,18 @@
 #define CONFIG_SYS_MCKR			0x1301
 #define CONFIG_SYS_MCKR_CSS		0x1302
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8400
+
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	0x800
@@ -176,10 +179,4 @@
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
-#elif CONFIG_SYS_USE_SPIFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8400
-
-#endif
-
 #endif
diff --git a/include/configs/sama5d2_ptc.h b/include/configs/sama5d2_ptc.h
index 75a81f1473..3ae16dfc63 100644
--- a/include/configs/sama5d2_ptc.h
+++ b/include/configs/sama5d2_ptc.h
@@ -72,7 +72,7 @@
 #define CONFIG_NET_RETRY_COUNT		20
 #define CONFIG_MACB_SEARCH_PHY
 
-#ifdef CONFIG_SYS_USE_NANDFLASH
+#ifdef CONFIG_NAND_BOOT
 #undef CONFIG_ENV_OFFSET
 #undef CONFIG_ENV_OFFSET_REDUND
 #undef CONFIG_BOOTCOMMAND
@@ -95,13 +95,14 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_SERIALFLASH
+#ifdef CONFIG_SPI_BOOT
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x8000
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_PMECC_CAP		8
 #define CONFIG_PMECC_SECTOR_SIZE	512
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
@@ -112,6 +113,5 @@
 #define CONFIG_SYS_NAND_BLOCK_SIZE	0x40000
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
-#endif
 
 #endif
diff --git a/include/configs/sama5d2_xplained.h b/include/configs/sama5d2_xplained.h
index 7b75413e8d..4f24a56899 100644
--- a/include/configs/sama5d2_xplained.h
+++ b/include/configs/sama5d2_xplained.h
@@ -47,7 +47,7 @@
 #define CONFIG_ATMEL_LCD_RGB565
 #endif
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 
 /* bootstrap + u-boot + env in sd card */
 #undef CONFIG_BOOTCOMMAND
@@ -69,11 +69,11 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
-#elif CONFIG_SYS_USE_SERIALFLASH
+#elif CONFIG_SPI_BOOT
 #define CONFIG_SPL_SPI_LOAD
 #define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
 
diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h
index 54ea98d454..a6697cdb63 100644
--- a/include/configs/sama5d3_xplained.h
+++ b/include/configs/sama5d3_xplained.h
@@ -69,12 +69,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
 
-#if CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
 /* SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x300000
@@ -86,13 +80,14 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	0x800
@@ -103,5 +98,3 @@
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
 #endif
-
-#endif
diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
index a7223e2cf0..bd93a1e84c 100644
--- a/include/configs/sama5d3xek.h
+++ b/include/configs/sama5d3xek.h
@@ -98,14 +98,6 @@
 
 #define CONFIG_SYS_LOAD_ADDR			0x22000000 /* load address */
 
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env*/
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
 /* SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x300000
@@ -117,13 +109,18 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
+
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_SIZE	0x800
@@ -133,10 +130,4 @@
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
-
-#endif
-
 #endif
diff --git a/include/configs/sama5d4_xplained.h b/include/configs/sama5d4_xplained.h
index f48ef40418..5dc5e7dd0c 100644
--- a/include/configs/sama5d4_xplained.h
+++ b/include/configs/sama5d4_xplained.h
@@ -58,14 +58,6 @@
 #define CONFIG_ATMEL_LCD_RGB565
 #endif
 
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env */
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env */
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
 /* SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x200000
@@ -77,13 +69,19 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
 #elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
+
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_PMECC_CAP		8
 #define CONFIG_PMECC_SECTOR_SIZE	512
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
@@ -95,9 +93,4 @@
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
-
-#endif
 #endif
diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h
index 0410d65ea0..94e8e893c0 100644
--- a/include/configs/sama5d4ek.h
+++ b/include/configs/sama5d4ek.h
@@ -54,14 +54,6 @@
 #define CONFIG_ATMEL_HLCD
 #define CONFIG_ATMEL_LCD_RGB565
 
-#ifdef CONFIG_SYS_USE_SERIALFLASH
-/* override the bootcmd, bootargs and other configuration for spi flash env*/
-#elif CONFIG_SYS_USE_NANDFLASH
-/* override the bootcmd, bootargs and other configuration for nandflash env*/
-#elif CONFIG_SYS_USE_MMC
-/* override the bootcmd, bootargs and other configuration for sd/mmc env */
-#endif
-
 /* SPL */
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x200000
@@ -73,13 +65,18 @@
 
 #define CONFIG_SYS_MONITOR_LEN		(512 << 10)
 
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
 
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_SPI_BOOT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
+
+#elif CONFIG_NAND_BOOT
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_BASE
+#endif
 #define CONFIG_PMECC_CAP		8
 #define CONFIG_PMECC_SECTOR_SIZE	512
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
@@ -91,9 +88,4 @@
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
 
-#elif CONFIG_SYS_USE_SERIALFLASH
-#define CONFIG_SPL_SPI_LOAD
-#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x10000
-
-#endif
 #endif
diff --git a/include/configs/vinco.h b/include/configs/vinco.h
index 0bd8bbbf9f..aaed8150b5 100644
--- a/include/configs/vinco.h
+++ b/include/configs/vinco.h
@@ -78,7 +78,7 @@
 #define CONFIG_NET_RETRY_COUNT		20
 #define CONFIG_MACB_SEARCH_PHY
 
-#ifdef CONFIG_SYS_USE_SERIALFLASH
+#ifdef CONFIG_SPI_BOOT
 /* bootstrap + u-boot + env + linux in serial flash */
 #define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
 #define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS