powerpc: mpc8xx: remove GEN860T, GEN806T_SC board support

These boards have been orphaned for a while and old enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

3 files changed, 0 insertions, 757 deletions

diff --git a/include/commproc.h b/include/commproc.h
index 7605713d47..76a62deba0 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -556,27 +556,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00002600)
 #endif	/* CONFIG_FPS850L, CONFIG_FPS860L */
 
-/*** GEN860T **********************************************************/
-#if defined(CONFIG_GEN860T)
-#undef	SCC_ENET
-#define	FEC_ENET
-
-#define PD_MII_TXD1	((ushort)0x1000)	/* PD  3	*/
-#define PD_MII_TXD2	((ushort)0x0800)	/* PD  4	*/
-#define PD_MII_TXD3	((ushort)0x0400)	/* PD  5	*/
-#define PD_MII_RX_DV	((ushort)0x0200)	/* PD  6	*/
-#define PD_MII_RX_ERR	((ushort)0x0100)	/* PD  7	*/
-#define PD_MII_RX_CLK	((ushort)0x0080)	/* PD  8	*/
-#define PD_MII_TXD0	((ushort)0x0040)	/* PD  9	*/
-#define PD_MII_RXD0	((ushort)0x0020)	/* PD 10	*/
-#define PD_MII_TX_ERR	((ushort)0x0010)	/* PD 11	*/
-#define PD_MII_MDC	((ushort)0x0008)	/* PD 12	*/
-#define PD_MII_RXD1	((ushort)0x0004)	/* PD 13	*/
-#define PD_MII_RXD2	((ushort)0x0002)	/* PD 14	*/
-#define PD_MII_RXD3	((ushort)0x0001)	/* PD 15	*/
-#define PD_MII_MASK	((ushort)0x1FFF)	/* PD 3-15	*/
-#endif	/* CONFIG_GEN860T */
-
 /*** HERMES-PRO ******************************************************/
 
 /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
deleted file mode 100644
index fd6c9763d8..0000000000
--- a/include/configs/GEN860T.h
+++ /dev/null
@@ -1,712 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Keith Outwater, keith_outwater@mvis.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config_GEN860T.h - board specific configuration options
- */
-
-#ifndef __CONFIG_GEN860T_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_MPC860
-#define CONFIG_GEN860T
-
-#define	CONFIG_SYS_TEXT_BASE		0x40000000
-
-/*
- * Identify the board
- */
-#if !defined(CONFIG_SC)
-#define CONFIG_IDENT_STRING		" B2"
-#else
-#define CONFIG_IDENT_STRING		" SC"
-#endif
-
-/*
- * Don't depend on the RTC clock to determine clock frequency -
- * the 860's internal rtc uses a 32.768 KHz clock which is
- * generated by the DS1337 - and the DS1337 clock can be turned off.
- */
-#if !defined(CONFIG_SC)
-#define	CONFIG_8xx_GCLK_FREQ		66600000
-#else
-#define	CONFIG_8xx_GCLK_FREQ		48000000
-#endif
-
-/*
- * The RS-232 console port is on SMC1
- */
-#define	CONFIG_8xx_CONS_SMC1
-#define CONFIG_BAUDRATE			38400
-
-/*
- * Print console information
- */
-#undef	 CONFIG_SYS_CONSOLE_INFO_QUIET
-
-/*
- * Set the autoboot delay in seconds.  A delay of -1 disables autoboot
- */
-#define CONFIG_BOOTDELAY				5
-
-/*
- * Pass the clock frequency to the Linux kernel in units of MHz
- */
-#define	CONFIG_CLOCKS_IN_MHZ
-
-#define CONFIG_PREBOOT		\
-	"echo;echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND	\
-	"bootp;" \
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
-	"bootm"
-
-/*
- * Turn off echo for serial download by default.  Allow baud rate to be changed
- * for downloads
- */
-#undef	CONFIG_LOADS_ECHO
-#define	CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/*
- * Turn off the watchdog timer
- */
-#undef	CONFIG_WATCHDOG
-
-/*
- * Do not reboot if a panic occurs
- */
-#define CONFIG_PANIC_HANG
-
-/*
- * Enable the status LED
- */
-#define	CONFIG_STATUS_LED
-
-/*
- * Reset address. We pick an address such that when an instruction
- * is executed at that address, a machine check exception occurs
- */
-#define CONFIG_SYS_RESET_ADDRESS				((ulong) -1)
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * The GEN860T network interface uses the on-chip 10/100 FEC with
- * an Intel LXT971A PHY connected to the 860T's MII. The PHY's
- * MII address is hardwired on the board to zero.
- */
-#define CONFIG_FEC_ENET
-#define CONFIG_SYS_DISCOVER_PHY
-#define CONFIG_MII
-#define CONFIG_MII_INIT			1
-#define CONFIG_PHY_ADDR			0
-
-/*
- * Set default IP stuff just to get bootstrap entries into the
- * environment so that we can source the full default environment.
- */
-#define CONFIG_ETHADDR					9a:52:63:15:85:25
-#define CONFIG_SERVERIP					10.0.4.201
-#define CONFIG_IPADDR					10.0.4.111
-
-/*
- * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to
- * the MPC860T I2C interface.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR				0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS		6		/* 64 byte pages		*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	12		/* 10 mS w/ 20% margin	*/
-#define	CONFIG_SYS_I2C_EEPROM_ADDR_LEN			2		/* need 16 bit address	*/
-#define CONFIG_ENV_EEPROM_SIZE				(32 * 1024)
-
-/*
- * Enable I2C and select the hardware/software driver
- */
-#define CONFIG_HARD_I2C		1		/* CPM based I2C */
-#undef	CONFIG_SYS_I2C_SOFT			/* Bit-banged I2C */
-
-#ifdef CONFIG_HARD_I2C
-#define	CONFIG_SYS_I2C_SPEED		100000	/* clock speed in Hz */
-#define CONFIG_SYS_I2C_SLAVE		0xFE	/* I2C slave address */
-#endif
-
-#ifdef CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-#define PB_SCL		0x00000020		/* PB 26 */
-#define PB_SDA		0x00000010		/* PB 27 */
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(5) /* 1/4 I2C clock duration */
-#endif
-
-/*
- * Allow environment overwrites by anyone
- */
-#define CONFIG_ENV_OVERWRITE
-
-#if !defined(CONFIG_SC)
-/*
- * The MPC860's internal RTC is horribly broken in rev D masks. Three
- * internal MPC860T circuit nodes were inadvertently left floating; this
- * causes KAPWR current in power down mode to be three orders of magnitude
- * higher than specified in the datasheet (from 10 uA to 10 mA).  No
- * reasonable battery can keep that kind RTC running during powerdown for any
- * length of time, so we use an external RTC on the I2C bus instead.
- */
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR				0x68
-
-#else
-/*
- * No external RTC on SC variant, so we're stuck with the internal one.
- */
-#define	CONFIG_RTC_MPC8xx
-#endif
-
-/*
- * Power On Self Test support
- */
-#define CONFIG_POST			  ( CONFIG_SYS_POST_CACHE		| \
-								CONFIG_SYS_POST_MEMORY		| \
-								CONFIG_SYS_POST_CPU		| \
-								CONFIG_SYS_POST_UART		| \
-								CONFIG_SYS_POST_SPR )
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_FPGA
-#define CONFIG_CMD_FPGA_LOADMK
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_BEDBUG
-
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-/*
- * There is no IDE/PCMCIA hardware support on the board.
- */
-#undef  CONFIG_IDE_PCMCIA
-#undef  CONFIG_IDE_LED
-#undef  CONFIG_IDE_RESET
-
-/*
- * Enable the call to misc_init_r() for miscellaneous platform
- * dependent initialization.
- */
-#define CONFIG_MISC_INIT_R
-
-/*
- * Enable call to last_stage_init() so we can twiddle some LEDS :)
- */
-#define CONFIG_LAST_STAGE_INIT
-
-/*
- * Virtex2 FPGA configuration support
- */
-#define CONFIG_FPGA_COUNT		1
-#define CONFIG_FPGA
-#define CONFIG_FPGA_XILINX
-#define CONFIG_FPGA_VIRTEX2
-#define CONFIG_SYS_FPGA_PROG_FEEDBACK
-
-/*
- * Verbose help from command monitor.
- */
-#define	CONFIG_SYS_LONGHELP
-#if !defined(CONFIG_SC)
-#define	CONFIG_SYS_PROMPT			"B2> "
-#else
-#define	CONFIG_SYS_PROMPT			"SC> "
-#endif
-
-
-/*
- * Use the "hush" command parser
- */
-#define	CONFIG_SYS_HUSH_PARSER
-
-/*
- * Set buffer size for console I/O
- */
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE			1024
-#else
-#define	CONFIG_SYS_CBSIZE			256
-#endif
-
-/*
- * Print buffer size
- */
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-/*
- * Maximum number of arguments that a command can accept
- */
-#define	CONFIG_SYS_MAXARGS			16
-
-/*
- * Boot argument buffer size
- */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-
-/*
- * Default memory test range
- */
-#define CONFIG_SYS_MEMTEST_START	0x0100000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START  + (128 * 1024))
-
-/*
- * Select the more full-featured memory test
- */
-#define	CONFIG_SYS_ALT_MEMTEST
-
-/*
- * Default load address
- */
-#define	CONFIG_SYS_LOAD_ADDR		0x01000000
-
-/*
- * Device memory map (after SDRAM remap to 0x0):
- *
- * CS		Device				Base Addr	Size
- * ----------------------------------------------------
- * CS0*		Flash				0x40000000	64 M
- * CS1*		SDRAM				0x00000000	16 M
- * CS2*		Disk-On-Chip		0x50000000	32 K
- * CS3*		FPGA				0x60000000	64 M
- * CS4*		SelectMap			0x70000000	32 K
- * CS5*		Mil-Std 1553 I/F	0x80000000	32 K
- * CS6*		Unused
- * CS7*		Unused
- * IMMR		860T Registers		0xfff00000
- */
-
-/*
- * Base addresses and block sizes
- */
-#define CONFIG_SYS_IMMR			0xFF000000
-
-#define SDRAM_BASE			0x00000000
-#define SDRAM_SIZE			(64 * 1024 * 1024)
-
-#define FLASH_BASE			0x40000000
-#define FLASH_SIZE			(16 * 1024 * 1024)
-
-#define DOC_BASE			0x50000000
-#define DOC_SIZE			(32 * 1024)
-
-#define FPGA_BASE			0x60000000
-#define FPGA_SIZE			(64 * 1024 * 1024)
-
-#define SELECTMAP_BASE		0x70000000
-#define SELECTMAP_SIZE		(32 * 1024)
-
-#define M1553_BASE			0x80000000
-#define M1553_SIZE			(64 * 1024)
-
-/*
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR		CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE		0x2F00	/* Size of used area in DPRAM		*/
-#define	CONFIG_SYS_INIT_DATA_SIZE		64	/* # bytes reserved for initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET		(CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET		CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE			SDRAM_BASE
-
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_BASE			FLASH_BASE
-#define CONFIG_SYS_FLASH_SIZE			FLASH_SIZE
-#define CONFIG_SYS_FLASH_SECT_SIZE		(128 * 1024)
-#define CONFIG_SYS_MAX_FLASH_BANKS		1
-#define CONFIG_SYS_MAX_FLASH_SECT		128
-
-/*
- * The timeout values are for an entire chip and are in milliseconds.
- * Yes I know that the write timeout is huge.  Accroding to the
- * datasheet a single byte takes 630 uS (round to 1 ms) max at worst
- * case VCC and temp after 100K programming cycles.  It works out
- * to 280 minutes (might as well be forever).
- */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(CONFIG_SYS_MAX_FLASH_SECT * 5000)
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(CONFIG_SYS_MAX_FLASH_SECT * 128 * 1024 * 1)
-
-/*
- * Allow direct writes to FLASH from tftp transfers (** dangerous **)
- */
-#define	CONFIG_SYS_DIRECT_FLASH_TFTP
-
-/*
- * Reserve memory for U-Boot.
- */
-#define CONFIG_SYS_MAX_UBOOT_SECTS		4
-#define	CONFIG_SYS_MONITOR_LEN			(CONFIG_SYS_MAX_UBOOT_SECTS * CONFIG_SYS_FLASH_SECT_SIZE)
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
-
-/*
- * Select environment placement.  NOTE that u-boot.lds must
- * be edited if this is changed!
- */
-#undef	CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_IS_IN_EEPROM
-
-#if defined(CONFIG_ENV_IS_IN_EEPROM)
-#define CONFIG_ENV_SIZE			(2 * 1024)
-#define CONFIG_ENV_OFFSET			(CONFIG_ENV_EEPROM_SIZE - (8 * 1024))
-#else
-#define CONFIG_ENV_SIZE			0x1000
-#define CONFIG_ENV_SECT_SIZE		CONFIG_SYS_FLASH_SECT_SIZE
-
-/*
- * This ultimately gets passed right into the linker script, so we have to
- * use a number :(
- */
-#define CONFIG_ENV_OFFSET			0x060000
-#endif
-
-/*
- * Reserve memory for malloc()
- */
-#define	CONFIG_SYS_MALLOC_LEN		(128 * 1024)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 * 1024 * 1024)
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE		16	/* For all MPC8xx CPUs				*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT		4	/* log base 2 of above value		*/
-#endif
-
-/*------------------------------------------------------------------------
- * SYPCR - System Protection Control							UM 11-9
- * -----------------------------------------------------------------------
- * SYPCR can only be written once after reset!
- *
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	( SYPCR_SWTC	| \
-					  SYPCR_BMT	| \
-					  SYPCR_BME	| \
-					  SYPCR_SWF	| \
-					  SYPCR_SWE	| \
-					  SYPCR_SWRI	| \
-					  SYPCR_SWP		  \
-					)
-#else
-#define CONFIG_SYS_SYPCR	( SYPCR_SWTC	| \
-					  SYPCR_BMT	| \
-					  SYPCR_BME	| \
-					  SYPCR_SWF	| \
-					  SYPCR_SWP		  \
-					)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration							UM 11-6
- *-----------------------------------------------------------------------
- * Set debug pin mux, enable SPKROUT and GPLB5*.
- */
-#define CONFIG_SYS_SIUMCR	( SIUMCR_DBGC11 | \
-					  SIUMCR_DBPC11 | \
-					  SIUMCR_MLRC11	| \
-					  SIUMCR_GB5E	  \
-					)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control							UM 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freeze enabled
- */
-#define CONFIG_SYS_TBSCR	( TBSCR_REFA | \
-					  TBSCR_REFB | \
-					  TBSCR_TBF	   \
-					)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register			UM 11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	( RTCSC_SEC	| \
-					  RTCSC_ALR | \
-					  RTCSC_RTF | \
-					  RTCSC_RTE	  \
-					)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control				UM 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	( PISCR_PS		| \
-					  PISCR_PITF	  \
-					)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register			UM 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit. Set MF for 1:2:1 mode.
- */
-#define CONFIG_SYS_PLPRCR	( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK)	| \
-					  PLPRCR_SPLSS	| \
-					  PLPRCR_TEXPS	| \
-					  PLPRCR_TMIST	  \
-					)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register				UM 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK   SCCR_EBDF11
-
-#if !defined(CONFIG_SC)
-#define CONFIG_SYS_SCCR	( SCCR_TBS			|	/* timebase = GCLK/2	*/ \
-					  SCCR_COM00		|	/* full strength CLKOUT	*/ \
-					  SCCR_DFSYNC00	|	/* SYNCLK / 1 (normal)	*/ \
-					  SCCR_DFBRG00		|	/* BRGCLK / 1 (normal)	*/ \
-					  SCCR_DFNL000		| \
-					  SCCR_DFNH000		  \
-					)
-#else
-#define CONFIG_SYS_SCCR	( SCCR_TBS			|	/* timebase = GCLK/2	*/ \
-					  SCCR_COM00		|	/* full strength CLKOUT	*/ \
-					  SCCR_DFSYNC00	|	/* SYNCLK / 1 (normal)	*/ \
-					  SCCR_DFBRG00		|	/* BRGCLK / 1 (normal)	*/ \
-					  SCCR_DFNL000		| \
-					  SCCR_DFNH000		| \
-					  SCCR_RTDIV		| \
-					  SCCR_RTSEL		  \
-					)
-#endif
-
-/*-----------------------------------------------------------------------
- * DER - Debug Enable Register									UM 37-46
- *-----------------------------------------------------------------------
- * Mask all events that can cause entry into debug mode
- */
-#define CONFIG_SYS_DER				0
-
-/*
- * Initialize Memory Controller:
- *
- * BR0 and OR0 (FLASH memory)
- */
-#define FLASH_BASE0_PRELIM	FLASH_BASE
-
-/*
- * Flash address mask
- */
-#define CONFIG_SYS_PRELIM_OR_AM	0xfe000000
-
-/*
- * FLASH timing:
- * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	( OR_CSNT_SAM	| \
-							  OR_ACS_DIV2	| \
-							  OR_BI			| \
-							  OR_SCY_2_CLK	| \
-							  OR_TRLX		| \
-							  OR_EHTR		  \
-							)
-
-#define CONFIG_SYS_OR0_PRELIM	( CONFIG_SYS_PRELIM_OR_AM		| \
-						  CONFIG_SYS_OR_TIMING_FLASH	  \
-						)
-
-#define CONFIG_SYS_BR0_PRELIM	( (FLASH_BASE0_PRELIM & BR_BA_MSK)	| \
-						  BR_MS_GPCM						| \
-						  BR_PS_8							| \
-						  BR_V								  \
-						)
-
-/*
- * SDRAM configuration
- */
-#define CONFIG_SYS_OR1_AM	0xfc000000
-#define CONFIG_SYS_OR1		( (CONFIG_SYS_OR1_AM & OR_AM_MSK)	| \
-					  OR_CSNT_SAM				  \
-					)
-
-#define CONFIG_SYS_BR1		( (SDRAM_BASE & BR_BA_MSK)	| \
-					  BR_MS_UPMA				| \
-					  BR_PS_32					| \
-					  BR_V						  \
-					)
-
-/*
- * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank
- * of 256 MBit SDRAM
- */
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16
-
-/*
- * Periodic timer for refresh @ 33 MHz system clock
- */
-#define CONFIG_SYS_MAMR_PTA	64
-
-/*
- * MAMR settings for SDRAM
- */
-#define CONFIG_SYS_MAMR_8COL	( (CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)	| \
-						  MAMR_PTAE				| \
-						  MAMR_AMA_TYPE_1			| \
-						  MAMR_DSA_1_CYCL			| \
-						  MAMR_G0CLA_A10			| \
-						  MAMR_RLFA_1X				| \
-						  MAMR_WLFA_1X				| \
-						  MAMR_TLFA_4X				  \
-						)
-
-/*
- * CS2* configuration for Disk On Chip:
- * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1,
- * no burst.
- */
-#define CONFIG_SYS_OR2_PRELIM	( (0xffff0000 & OR_AM_MSK)	| \
-						  OR_CSNT_SAM				| \
-						  OR_ACS_DIV2				| \
-						  OR_BI						| \
-						  OR_SCY_2_CLK				| \
-						  OR_TRLX					| \
-						  OR_EHTR					  \
-						)
-
-#define CONFIG_SYS_BR2_PRELIM	( (DOC_BASE & BR_BA_MSK)	| \
-						  BR_PS_8					| \
-						  BR_MS_GPCM				| \
-						  BR_V						  \
-						)
-
-/*
- * CS3* configuration for FPGA:
- * 33 MHz bus with SCY=15, no burst.
- * The FPGA uses TA and TEA to terminate bus cycles, but we
- * clear SETA and set the cycle length to a large number so that
- * the cycle will still complete even if there is a configuration
- * error that prevents TA from asserting on FPGA accesss.
- */
-#define CONFIG_SYS_OR3_PRELIM	( (0xfc000000 & OR_AM_MSK)  | \
-						  OR_SCY_15_CLK				| \
-						  OR_BI					  \
-						)
-
-#define CONFIG_SYS_BR3_PRELIM	( (FPGA_BASE & BR_BA_MSK)	| \
-						  BR_PS_32					| \
-						  BR_MS_GPCM				| \
-						  BR_V						  \
-						)
-/*
- * CS4* configuration for FPGA SelectMap configuration interface.
- * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge
- * of GCLK1_50
- */
-#define CONFIG_SYS_OR4_PRELIM	( (0xffff0000 & OR_AM_MSK)	| \
-						  OR_G5LS						| \
-						  OR_BI							  \
-						)
-
-#define CONFIG_SYS_BR4_PRELIM	( (SELECTMAP_BASE & BR_BA_MSK)	| \
-						  BR_PS_8						| \
-						  BR_MS_UPMB					| \
-						  BR_V							  \
-						)
-
-/*
- * CS5* configuration for Mil-Std 1553 databus interface.
- * 33 MHz bus, GPCM, no burst.
- * The 1553 interface  uses TA and TEA to terminate bus cycles,
- * but we clear SETA and set the cycle length to a large number so that
- * the cycle will still complete even if there is a configuration
- * error that prevents TA from asserting on FPGA accesss.
- */
-#define CONFIG_SYS_OR5_PRELIM	( (0xffff0000 & OR_AM_MSK)  | \
-						  OR_SCY_15_CLK				| \
-						  OR_EHTR					| \
-						  OR_TRLX					| \
-						  OR_CSNT_SAM				| \
-						  OR_BI						  \
-						)
-
-#define CONFIG_SYS_BR5_PRELIM	( (M1553_BASE & BR_BA_MSK)	| \
-						  BR_PS_16					| \
-						  BR_MS_GPCM				| \
-						  BR_V						  \
-						)
-
-/*
- * FEC interrupt assignment
- */
-#define FEC_INTERRUPT   SIU_LEVEL1
-
-/*
- * Sanity checks
- */
-#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
-#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
-#endif
-
-#endif	/* __CONFIG_GEN860T_H */
diff --git a/include/status_led.h b/include/status_led.h
index c9d21d105f..c1d2242b9d 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -56,30 +56,6 @@ void status_led_set  (int led, int state);
 
 # define STATUS_LED_BOOT	0		/* LED 0 used for boot status */
 
-/*****  GEN860T  *********************************************************/
-#elif defined(CONFIG_GEN860T)
-
-# define STATUS_LED_PAR			im_ioport.iop_papar
-# define STATUS_LED_DIR			im_ioport.iop_padir
-# define STATUS_LED_ODR			im_ioport.iop_paodr
-# define STATUS_LED_DAT			im_ioport.iop_padat
-
-# define STATUS_LED_BIT			0x0800	/* Red LED 0 is on PA.4	*/
-# define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE		STATUS_LED_OFF
-# define STATUS_LED_BIT1		0x0400	/* Grn LED 1 is on PA.5	*/
-# define STATUS_LED_PERIOD1		(CONFIG_SYS_HZ / 8)
-# define STATUS_LED_STATE1		STATUS_LED_BLINKING
-# define STATUS_LED_BIT2		0x0080	/* Red LED 2 is on PA.8	*/
-# define STATUS_LED_PERIOD2		(CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE2		STATUS_LED_OFF
-# define STATUS_LED_BIT3		0x0040	/* Grn LED 3 is on PA.9	*/
-# define STATUS_LED_PERIOD3		(CONFIG_SYS_HZ / 4)
-# define STATUS_LED_STATE3		STATUS_LED_OFF
-
-# define STATUS_LED_ACTIVE		1	/* LED on for bit == 1	*/
-# define STATUS_LED_BOOT		1	/* Boot status on LED 1	*/
-
 /*****  IVMS8  **********************************************************/
 #elif defined(CONFIG_IVMS8)