include/configs: Use new CONFIG_CMD_* in various o* named board config files.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

8 files changed, 111 insertions, 67 deletions

diff --git a/include/configs/o2dnt.h b/include/configs/o2dnt.h
index 63d0da7d09..9ed1ed856c 100644
--- a/include/configs/o2dnt.h
+++ b/include/configs/o2dnt.h
@@ -37,11 +37,6 @@
 #define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH  */
 #define BOOTFLAG_WARM		0x02	/* Software reboot	     */
 
-#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
 /*
  * Serial console configuration
  */
@@ -82,20 +77,20 @@
 
 #define CONFIG_TIMESTAMP	/* Print image info with timestamp */
 
+
 /*
- * Supported commands
+ * Command line configuration.
  */
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_PING	| \
-				ADD_PCI_CMD	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_PCI_CMD
+
 
 #if (TEXT_BASE == 0xFF000000)		/* Boot low with 16 MB Flash */
 #   define CFG_LOWBOOT		1
@@ -246,7 +241,7 @@
 #define CFG_LONGHELP			/* undef to save memory	    */
 #define CFG_PROMPT		"=> "	/* Monitor Command Prompt   */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CFG_CBSIZE		256	/* Console I/O Buffer Size  */
@@ -262,6 +257,11 @@
 
 #define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
+#define CFG_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
 /*
  * Various low-level settings
  */
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index 68e8cec251..fd45c1d970 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -232,26 +232,29 @@
 
 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO	| \
-				CFG_CMD_SDRAM	| \
-				CFG_CMD_SNTP	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -260,7 +263,7 @@
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -310,7 +313,7 @@
  */
 #define CFG_DCACHE_SIZE		32768	/* For AMCC 440 CPUs			*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 
@@ -322,7 +325,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h
index 016d3d8bd0..11fdb47101 100644
--- a/include/configs/omap1510inn.h
+++ b/include/configs/omap1510inn.h
@@ -86,11 +86,19 @@
 #define CONFIG_BAUDRATE		115200
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | CFG_CMD_DHCP)
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
 #define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 #include <configs/omap1510.h>
 
 #define CONFIG_BOOTDELAY	3
@@ -98,7 +106,7 @@
 #define CONFIG_BOOTCOMMAND	"bootp;tftp;bootm"
 #define CFG_AUTOLOAD		"n"		/* No autoload */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200		/* speed to run kgdb serial port */
 /* what's this ? it's not used anywhere */
 #define CONFIG_KGDB_SER_INDEX	1		/* which serial port to use */
diff --git a/include/configs/omap1610h2.h b/include/configs/omap1610h2.h
index c6ca689a5f..d78f79f121 100644
--- a/include/configs/omap1610h2.h
+++ b/include/configs/omap1610h2.h
@@ -81,11 +81,17 @@
 #define CONFIG_BAUDRATE	115200
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
 #define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 #include <configs/omap1510.h>
 
 #define CONFIG_BOOTDELAY	3
@@ -93,7 +99,7 @@
 #define CONFIG_BOOTCOMMAND      "bootp;tftp;bootm"
 #define CFG_AUTOLOAD            "n"             /* No autoload */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
diff --git a/include/configs/omap1610inn.h b/include/configs/omap1610inn.h
index f28ede0967..7d0658fd7d 100644
--- a/include/configs/omap1610inn.h
+++ b/include/configs/omap1610inn.h
@@ -82,11 +82,17 @@
 #define CONFIG_BAUDRATE	115200
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
 #define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 #include <configs/omap1510.h>
 
 #define CONFIG_BOOTDELAY	3
@@ -98,7 +104,7 @@
 #define CONFIG_SERVERIP	156.117.97.139	/* current IP of my dev pc */
 #define CONFIG_BOOTFILE	"uImage"	/* file to load */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
diff --git a/include/configs/omap2420h4.h b/include/configs/omap2420h4.h
index 58374616a1..46e0dcc478 100644
--- a/include/configs/omap2420h4.h
+++ b/include/configs/omap2420h4.h
@@ -119,15 +119,27 @@
 #define CONFIG_BAUDRATE          115200
 #define CFG_BAUDRATE_TABLE       {9600, 19200, 38400, 57600, 115200}
 
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
 #ifdef CFG_NAND_BOOT
-#define CONFIG_COMMANDS          (CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_NAND | CFG_CMD_JFFS2)
+    #define CONFIG_CMD_DHCP
+    #define CONFIG_CMD_I2C
+    #define CONFIG_CMD_NAND
+    #define CONFIG_CMD_JFFS2
 #else
-#define CONFIG_COMMANDS          ((CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_JFFS2) & ~CFG_CMD_AUTOSCRIPT)
+    #define CONFIG_CMD_DHCP
+    #define CONFIG_CMD_I2C
+    #define CONFIG_CMD_JFFS2
+
+    #undef CONFIG_CMD_AUTOSCRIPT
 #endif
-#define CONFIG_BOOTP_MASK        CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTP_MASK        CONFIG_BOOTP_DEFAULT
 
 /*
  *  Board NAND Info.
diff --git a/include/configs/omap5912osk.h b/include/configs/omap5912osk.h
index 5db4f52beb..296b6bc980 100644
--- a/include/configs/omap5912osk.h
+++ b/include/configs/omap5912osk.h
@@ -86,11 +86,17 @@
 #define CONFIG_BAUDRATE	115200
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
 #define CONFIG_BOOTP_MASK	CONFIG_BOOTP_DEFAULT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 #include <configs/omap1510.h>
 
 #define CONFIG_BOOTDELAY	3
@@ -102,7 +108,7 @@
 #define CONFIG_SERVERIP	156.117.97.139	/* current IP of my dev pc */
 #define CONFIG_BOOTFILE	"uImage"	/* file to load */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	1	/* which serial port to use */
 #endif
diff --git a/include/configs/omap730p2.h b/include/configs/omap730p2.h
index fda55cf06f..af9877f24a 100644
--- a/include/configs/omap730p2.h
+++ b/include/configs/omap730p2.h
@@ -90,14 +90,17 @@
 #define CONFIG_BAUDRATE		   115200
 #define CFG_BAUDRATE_TABLE	   { 9600, 19200, 38400, 57600, 115200 }
 
-#define CONFIG_COMMANDS		   (CONFIG_CMD_DFL | CFG_CMD_DHCP)
-#define CONFIG_BOOTP_MASK	   CONFIG_BOOTP_DEFAULT
 
 /*
- * This must be included AFTER the definition of CONFIG_COMMANDS (if any)
+ * Command line configuration.
  */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
+#define CONFIG_BOOTP_MASK	   CONFIG_BOOTP_DEFAULT
 
-#include <cmd_confdefs.h>
 #include <configs/omap730.h>
 #include <configs/h2_p2_dbg_board.h>
 
@@ -112,7 +115,7 @@
 #define CONFIG_SERVERIP		   192.150.0.100
 #define CONFIG_BOOTFILE		   "uImage"  /* File to load */
 
-#if defined (CONFIG_COMMANDS) && defined (CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	   115200    /* Speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	   1	     /* Which serial port to use */
 #endif