Merge branch 'master' of git://git.denx.de/u-boot-arm

10 files changed, 213 insertions, 5 deletions

diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h
index 70dd47ecb5..80a5797493 100644
--- a/include/configs/ap325rxa.h
+++ b/include/configs/ap325rxa.h
@@ -138,6 +138,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x200	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x200	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x210	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /* if you use all NOR Flash , you change dip-switch. Please see Manual. */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 055931cda6..57dd1651f3 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -60,7 +60,7 @@
 
 #define ORION5X_MPP0_7		0x00000003
 #define ORION5X_MPP8_15		0x55550000
-#define ORION5X_MPP16_23	0x00000000
+#define ORION5X_MPP16_23	0x00005555
 
 /*
  * Board-specific values for Orion5x GPIO low level init:
@@ -131,6 +131,7 @@
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
 
 /*
  * Network
@@ -150,6 +151,37 @@
 #endif
 
 /*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
  *  Environment variables configurations
  */
 #define CONFIG_ENV_IS_IN_FLASH		1
diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h
index ba0a3f8043..0ea3527e30 100644
--- a/include/configs/ms7720se.h
+++ b/include/configs/ms7720se.h
@@ -122,5 +122,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0		/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0		/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x200		/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 #endif	/* __MS7720SE_H */
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index b1e40a38f6..a0d27a437d 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -35,6 +35,7 @@
 #define CONFIG_OMAP44XX		1	/* which is a 44XX */
 #define CONFIG_OMAP4430		1	/* which is in a 4430 */
 #define CONFIG_PANDA		1	/* working with Panda */
+#define CONFIG_ARCH_CPU_INIT
 
 /* Get CPU defs */
 #include <asm/arch/cpu.h>
@@ -102,12 +103,29 @@
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 #define CONFIG_I2C_MULTI_BUS		1
 
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER		1
+
 /* MMC */
 #define CONFIG_MMC			1
 #define CONFIG_OMAP3_MMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"OMAP4 Panda"
+
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
 
@@ -135,16 +153,21 @@
  * Environment setup
  */
 
+#define CONFIG_BOOTDELAY	3
+
 /* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
+	"usbtty=cdc_acm\0" \
+	"vram=16M\0" \
 	"mmcdev=1\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
+		"vram=${vram} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
 	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -162,7 +185,6 @@
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
-			"else run nandboot; " \
 			"fi; " \
 		"fi; " \
 	"fi"
@@ -195,7 +217,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x80000000
 
 /* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE		GPT1_BASE
+#define CONFIG_SYS_TIMERBASE		GPT2_BASE
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000
 
diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h
index 8121554448..d5439f988a 100644
--- a/include/configs/omap4_sdp4430.h
+++ b/include/configs/omap4_sdp4430.h
@@ -36,6 +36,7 @@
 #define CONFIG_OMAP44XX		1	/* which is a 44XX */
 #define CONFIG_OMAP4430		1	/* which is in a 4430 */
 #define CONFIG_4430SDP		1	/* working with SDP */
+#define CONFIG_ARCH_CPU_INIT
 
 /* Get CPU defs */
 #include <asm/arch/cpu.h>
@@ -103,12 +104,29 @@
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 #define CONFIG_I2C_MULTI_BUS		1
 
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER		1
+
 /* MMC */
 #define CONFIG_MMC			1
 #define CONFIG_OMAP3_MMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"SDP4430"
+
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
 
@@ -136,16 +154,21 @@
  * Environment setup
  */
 
+#define CONFIG_BOOTDELAY	3
+
 /* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
+	"usbtty=cdc_acm\0" \
+	"vram=16M\0" \
 	"mmcdev=1\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
+		"vram=${vram} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
 	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -163,7 +186,6 @@
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
-			"else run nandboot; " \
 			"fi; " \
 		"fi; " \
 	"fi"
@@ -196,7 +218,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x80000000
 
 /* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE		GPT1_BASE
+#define CONFIG_SYS_TIMERBASE		GPT2_BASE
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000
 
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
index 52fa73def9..846dfcd484 100644
--- a/include/configs/openrd_base.h
+++ b/include/configs/openrd_base.h
@@ -103,6 +103,7 @@
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
 
 /*
  * NAND configuration
@@ -205,6 +206,36 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
+ * IDe Support on SATA port0
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	KW_SATA_BASE
+/* ATA bus 0 is Kirkwood port 0 on openrd */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	KW_SATA_PORT0_OFFSET
+/* ATA bus 1 is Kirkwood port 1 on openrd */
+#define CONFIG_SYS_ATA_IDE1_OFFSET	KW_SATA_PORT1_OFFSET
+#endif /* CONFIG_CMD_IDE */
+
+/*
  * File system
  */
 #define CONFIG_CMD_FAT
diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h
index 8931b974aa..955f3ff57f 100644
--- a/include/configs/r2dplus.h
+++ b/include/configs/r2dplus.h
@@ -96,6 +96,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x1000	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x1000	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x800	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /*
  * SuperH PCI Bridge Configration
diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h
index 71c570eee9..3afe93a671 100644
--- a/include/configs/r7780mp.h
+++ b/include/configs/r7780mp.h
@@ -171,6 +171,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET     0x1000          /* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET      0x1000          /* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET      0x800           /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 #endif /* CONFIG_CMD_IDE */
 
 #endif /* __R7780RP_H */
diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h
index ff0dbd3c21..c8ea8fda82 100644
--- a/include/configs/s5p_goni.h
+++ b/include/configs/s5p_goni.h
@@ -67,6 +67,11 @@
 #define CONFIG_SERIAL_MULTI		1
 #define CONFIG_BAUDRATE			115200
 
+/* MMC */
+#define CONFIG_GENERIC_MMC		1
+#define CONFIG_MMC			1
+#define CONFIG_S5P_MMC			1
+
 /* It should define before config_cmd_default.h */
 #define CONFIG_SYS_NO_FLASH		1
 
@@ -82,6 +87,7 @@
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_ONENAND
 #define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_MMC
 
 #define CONFIG_BOOTDELAY		1
 #define CONFIG_ZERO_BOOTDELAY_CHECK
diff --git a/include/twl6030.h b/include/twl6030.h
new file mode 100644
index 0000000000..54923ab2e4
--- /dev/null
+++ b/include/twl6030.h
@@ -0,0 +1,91 @@
+/*
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+/* I2C chip addresses */
+#define TWL6030_CHIP_PM		0x48
+
+#define TWL6030_CHIP_USB	0x49
+#define TWL6030_CHIP_ADC	0x49
+#define TWL6030_CHIP_CHARGER	0x49
+#define TWL6030_CHIP_PWM	0x49
+
+/* Battery CHARGER REGISTERS */
+#define CONTROLLER_INT_MASK	0xE0
+#define CONTROLLER_CTRL1	0xE1
+#define CONTROLLER_WDG		0xE2
+#define CONTROLLER_STAT1	0xE3
+#define CHARGERUSB_INT_STATUS	0xE4
+#define CHARGERUSB_INT_MASK	0xE5
+#define CHARGERUSB_STATUS_INT1	0xE6
+#define CHARGERUSB_STATUS_INT2	0xE7
+#define CHARGERUSB_CTRL1	0xE8
+#define CHARGERUSB_CTRL2	0xE9
+#define CHARGERUSB_CTRL3	0xEA
+#define CHARGERUSB_STAT1	0xEB
+#define CHARGERUSB_VOREG	0xEC
+#define CHARGERUSB_VICHRG	0xED
+#define CHARGERUSB_CINLIMIT	0xEE
+#define CHARGERUSB_CTRLLIMIT1	0xEF
+
+/* CHARGERUSB_VICHRG */
+#define CHARGERUSB_VICHRG_500		0x4
+#define CHARGERUSB_VICHRG_1500		0xE
+/* CHARGERUSB_CINLIMIT */
+#define CHARGERUSB_CIN_LIMIT_100	0x1
+#define CHARGERUSB_CIN_LIMIT_300	0x5
+#define CHARGERUSB_CIN_LIMIT_500	0x9
+#define CHARGERUSB_CIN_LIMIT_NONE	0xF
+/* CONTROLLER_INT_MASK */
+#define MVAC_FAULT		(1 << 6)
+#define MAC_EOC			(1 << 5)
+#define MBAT_REMOVED		(1 << 4)
+#define MFAULT_WDG		(1 << 3)
+#define MBAT_TEMP		(1 << 2)
+#define MVBUS_DET		(1 << 1)
+#define MVAC_DET		(1 << 0)
+/* CHARGERUSB_INT_MASK */
+#define MASK_MCURRENT_TERM		(1 << 3)
+#define MASK_MCHARGERUSB_STAT		(1 << 2)
+#define MASK_MCHARGERUSB_THMREG		(1 << 1)
+#define MASK_MCHARGERUSB_FAULT		(1 << 0)
+/* CHARGERUSB_VOREG */
+#define CHARGERUSB_VOREG_3P52		0x01
+#define CHARGERUSB_VOREG_4P0		0x19
+#define CHARGERUSB_VOREG_4P2		0x23
+#define CHARGERUSB_VOREG_4P76		0x3F
+/* CHARGERUSB_CTRL2 */
+#define CHARGERUSB_CTRL2_VITERM_50	(0 << 5)
+#define CHARGERUSB_CTRL2_VITERM_100	(1 << 5)
+#define CHARGERUSB_CTRL2_VITERM_150	(2 << 5)
+/* CONTROLLER_CTRL1 */
+#define CONTROLLER_CTRL1_EN_CHARGER	(1 << 4)
+#define CONTROLLER_CTRL1_SEL_CHARGER	(1 << 3)
+
+#define VUSB_CFG_STATE		0xA2
+#define MISC2			0xE5
+
+void twl6030_init_battery_charging(void);
+void twl6030_usb_device_settings(void);