Merge branch 'master' of git://git.denx.de/u-boot-arm

95 files changed, 2133 insertions, 6782 deletions

diff --git a/include/aes.h b/include/aes.h
index ea06308279..6315c02aa9 100644
--- a/include/aes.h
+++ b/include/aes.h
@@ -8,6 +8,13 @@
 #ifndef _AES_REF_H_
 #define _AES_REF_H_
 
+#ifdef USE_HOSTCC
+/* Define compat stuff for use in fw_* tools. */
+typedef unsigned char u8;
+typedef unsigned int u32;
+#define debug(...) do {} while (0)
+#endif
+
 /*
  * AES encryption library, with small code size, supporting only 128-bit AES
  *
@@ -25,30 +32,63 @@ enum {
 };
 
 /**
+ * aes_expand_key() - Expand the AES key
+ *
  * Expand a key into a key schedule, which is then used for the other
  * operations.
  *
- * \param key		Key, of length AES_KEY_LENGTH bytes
- * \param expkey	Buffer to place expanded key, AES_EXPAND_KEY_LENGTH
+ * @key		Key, of length AES_KEY_LENGTH bytes
+ * @expkey	Buffer to place expanded key, AES_EXPAND_KEY_LENGTH
  */
 void aes_expand_key(u8 *key, u8 *expkey);
 
 /**
- * Encrypt a single block of data
+ * aes_encrypt() - Encrypt single block of data with AES 128
  *
- * in		Input data
- * expkey	Expanded key to use for encryption (from aes_expand_key())
- * out		Output data
+ * @in		Input data
+ * @expkey	Expanded key to use for encryption (from aes_expand_key())
+ * @out		Output data
  */
 void aes_encrypt(u8 *in, u8 *expkey, u8 *out);
 
 /**
- * Decrypt a single block of data
+ * aes_decrypt() - Decrypt single block of data with AES 128
  *
- * in		Input data
- * expkey	Expanded key to use for decryption (from aes_expand_key())
- * out		Output data
+ * @in		Input data
+ * @expkey	Expanded key to use for decryption (from aes_expand_key())
+ * @out		Output data
  */
 void aes_decrypt(u8 *in, u8 *expkey, u8 *out);
 
+/**
+ * Apply chain data to the destination using EOR
+ *
+ * Each array is of length AES_KEY_LENGTH.
+ *
+ * @cbc_chain_data	Chain data
+ * @src			Source data
+ * @dst			Destination data, which is modified here
+ */
+void aes_apply_cbc_chain_data(u8 *cbc_chain_data, u8 *src, u8 *dst);
+
+/**
+ * aes_cbc_encrypt_blocks() - Encrypt multiple blocks of data with AES CBC.
+ *
+ * @key_exp		Expanded key to use
+ * @src			Source data to encrypt
+ * @dst			Destination buffer
+ * @num_aes_blocks	Number of AES blocks to encrypt
+ */
+void aes_cbc_encrypt_blocks(u8 *key_exp, u8 *src, u8 *dst, u32 num_aes_blocks);
+
+/**
+ * Decrypt multiple blocks of data with AES CBC.
+ *
+ * @key_exp		Expanded key to use
+ * @src			Source data to decrypt
+ * @dst			Destination buffer
+ * @num_aes_blocks	Number of AES blocks to decrypt
+ */
+void aes_cbc_decrypt_blocks(u8 *key_exp, u8 *src, u8 *dst, u32 num_aes_blocks);
+
 #endif /* _AES_REF_H_ */
diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h
index 707400e847..e98b661e35 100644
--- a/include/asm-generic/global_data.h
+++ b/include/asm-generic/global_data.h
@@ -80,6 +80,9 @@ typedef struct global_data {
 #if defined(CONFIG_SYS_I2C)
 	int		cur_i2c_bus;	/* current used i2c bus */
 #endif
+#ifdef CONFIG_SYS_I2C_MXC
+	void *srdata[10];
+#endif
 	unsigned long timebase_h;
 	unsigned long timebase_l;
 	struct arch_global_data arch;	/* architecture-specific data */
diff --git a/include/asm-generic/u-boot.h b/include/asm-generic/u-boot.h
index e78196797b..c18e4ca27a 100644
--- a/include/asm-generic/u-boot.h
+++ b/include/asm-generic/u-boot.h
@@ -108,9 +108,6 @@ typedef struct bd_info {
 	unsigned int	bi_opbfreq;		/* OPB clock in Hz */
 	int		bi_iic_fast[2];		/* Use fast i2c mode */
 #endif
-#if defined(CONFIG_NX823)
-	unsigned char	bi_sernum[8];
-#endif
 #if defined(CONFIG_4xx)
 #if defined(CONFIG_440GX) || \
 		defined(CONFIG_460EX) || defined(CONFIG_460GT)
diff --git a/include/common.h b/include/common.h
index cbd3c9e043..5fb0bb2d3d 100644
--- a/include/common.h
+++ b/include/common.h
@@ -505,19 +505,8 @@ extern ssize_t spi_read	 (uchar *, int, uchar *, int);
 extern ssize_t spi_write (uchar *, int, uchar *, int);
 #endif
 
-#ifdef CONFIG_RPXCLASSIC
-void rpxclassic_init (void);
-#endif
-
 void rpxlite_init (void);
 
-#ifdef CONFIG_MBX
-/* $(BOARD)/mbx8xx.c */
-void	mbx_init (void);
-void	board_serial_init (void);
-void	board_ether_init (void);
-#endif
-
 #ifdef CONFIG_HERMES
 /* $(BOARD)/hermes.c */
 void hermes_start_lxt980 (int speed);
@@ -692,9 +681,6 @@ ulong	get_UCLK (void);
 #if defined(CONFIG_LH7A40X)
 ulong	get_PLLCLK (void);
 #endif
-#if defined CONFIG_INCA_IP
-uint	incaip_get_cpuclk (void);
-#endif
 #if defined(CONFIG_IMX)
 ulong get_systemPLLCLK(void);
 ulong get_FCLK(void);
diff --git a/include/common_timing_params.h b/include/common_timing_params.h
index 76338d4e6c..821de21de7 100644
--- a/include/common_timing_params.h
+++ b/include/common_timing_params.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008 Freescale Semiconductor, Inc.
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -14,32 +14,45 @@ typedef struct {
 
 	unsigned int tckmin_x_ps;
 	unsigned int tckmax_ps;
-	unsigned int tckmax_max_ps;
 	unsigned int trcd_ps;
 	unsigned int trp_ps;
 	unsigned int tras_ps;
+#if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4)
+	unsigned int taamin_ps;
+#endif
 
-	unsigned int twr_ps;	/* maximum = 63750 ps */
+#ifdef CONFIG_SYS_FSL_DDR4
+	unsigned int trfc1_ps;
+	unsigned int trfc2_ps;
+	unsigned int trfc4_ps;
+	unsigned int trrds_ps;
+	unsigned int trrdl_ps;
+	unsigned int tccdl_ps;
+#else
 	unsigned int twtr_ps;	/* maximum = 63750 ps */
 	unsigned int trfc_ps;	/* maximum = 255 ns + 256 ns + .75 ns
 					   = 511750 ps */
 
 	unsigned int trrd_ps;	/* maximum = 63750 ps */
+	unsigned int trtp_ps;	/* byte 38, spd->trtp */
+#endif
+	unsigned int twr_ps;	/* maximum = 63750 ps */
 	unsigned int trc_ps;	/* maximum = 254 ns + .75 ns = 254750 ps */
 
 	unsigned int refresh_rate_ps;
 	unsigned int extended_op_srt;
 
+#if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
 	unsigned int tis_ps;	/* byte 32, spd->ca_setup */
 	unsigned int tih_ps;	/* byte 33, spd->ca_hold */
 	unsigned int tds_ps;	/* byte 34, spd->data_setup */
 	unsigned int tdh_ps;	/* byte 35, spd->data_hold */
-	unsigned int trtp_ps;	/* byte 38, spd->trtp */
 	unsigned int tdqsq_max_ps;	/* byte 44, spd->tdqsq */
 	unsigned int tqhs_ps;	/* byte 45, spd->tqhs */
+#endif
 
 	unsigned int ndimms_present;
-	unsigned int lowest_common_SPD_caslat;
+	unsigned int lowest_common_spd_caslat;
 	unsigned int highest_common_derated_caslat;
 	unsigned int additive_latency;
 	unsigned int all_dimms_burst_lengths_bitmask;
diff --git a/include/commproc.h b/include/commproc.h
index c10a79c839..29a3e61e80 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -12,10 +12,6 @@
  * CPM capabilities.  I (or someone else) will add definitions as they
  * are needed.  -- Dan
  *
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
- * or other use.
  */
 #ifndef __CPM_8XX__
 #define __CPM_8XX__
@@ -135,7 +131,6 @@ typedef struct cpm_buf_desc {
 #define PROFF_SMC2	((uint)0x0380)
 
 /* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
  */
 typedef struct smc_uart {
 	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
@@ -434,38 +429,6 @@ typedef struct scc_enet {
  * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
  **********************************************************************/
 
-
-/***  ADS  *************************************************************/
-
-#if defined(CONFIG_MPC860) && defined(CONFIG_ADS)
-/* This ENET stuff is for the MPC860ADS with ethernet on SCC1.
- */
-
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0100)
-#define PA_ENET_RCLK	((ushort)0x0200)
-
-#define PB_ENET_TENA	((uint)0x00001000)
-
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000002c)
-
-/* 68160 PHY control */
-
-#define PC_ENET_ETHLOOP ((ushort)0x0800)
-#define PC_ENET_TPFLDL	((ushort)0x0400)
-#define PC_ENET_TPSQEL  ((ushort)0x0200)
-
-#endif	/* MPC860ADS */
-
 /***  BSEIP  **********************************************************/
 
 #ifdef CONFIG_BSEIP
@@ -568,62 +531,6 @@ typedef struct scc_enet {
 
 #endif
 
-/***  FADS823  ********************************************************/
-
-#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC823FADS with ethernet on SCC2.
- */
-#ifdef CONFIG_SCC2_ENET
-#define	PROFF_ENET	PROFF_SCC2
-#define	CPM_CR_ENET	CPM_CR_CH_SCC2
-#define	SCC_ENET	1
-#define CPMVEC_ENET	CPMVEC_SCC2
-#endif
-
-#ifdef CONFIG_SCC1_ENET
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define CPMVEC_ENET	CPMVEC_SCC1
-#endif
-
-#define PA_ENET_RXD	((ushort)0x0004)
-#define PA_ENET_TXD	((ushort)0x0008)
-#define PA_ENET_TCLK	((ushort)0x0400)
-#define PA_ENET_RCLK	((ushort)0x0200)
-
-#define PB_ENET_TENA	((uint)0x00002000)
-
-#define PC_ENET_CLSN	((ushort)0x0040)
-#define PC_ENET_RENA	((ushort)0x0080)
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002e00)
-
-#endif	/* CONFIG_FADS823FADS */
-
-/***  FADS850SAR  ********************************************************/
-
-#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC850SAR with ethernet on SCC2.  Some of
- * this may be unique to the FADS850SAR configuration.
- * Note TENA is on Port B.
- */
-#define	PROFF_ENET	PROFF_SCC2
-#define	CPM_CR_ENET	CPM_CR_CH_SCC2
-#define	SCC_ENET	1
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0200)	/* PA 6 */
-#define PA_ENET_TCLK	((ushort)0x0800)	/* PA 4 */
-#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC 9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC 8 */
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002f00)	/* RCLK-CLK2, TCLK-CLK4 */
-#endif	/* CONFIG_FADS850SAR */
-
 /***  FADS860T********************************************************/
 
 #if defined(CONFIG_FADS) && defined(CONFIG_MPC86x)
@@ -709,32 +616,6 @@ typedef struct scc_enet {
 #define PD_MII_MASK	((ushort)0x1FFF)	/* PD 3-15	*/
 #endif	/* CONFIG_GEN860T */
 
-/***  GENIETV  ********************************************************/
-
-#if defined(CONFIG_GENIETV)
-/* Ethernet is only on SCC2 */
-
-#define CONFIG_SCC2_ENET
-#define	PROFF_ENET	PROFF_SCC2
-#define	CPM_CR_ENET	CPM_CR_CH_SCC2
-#define	SCC_ENET	1
-#define CPMVEC_ENET	CPMVEC_SCC2
-
-#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
-#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
-#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
-
-#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
-
-#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002e00)
-
-#endif	/* CONFIG_GENIETV */
-
 /*** HERMES-PRO ******************************************************/
 
 /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
@@ -888,60 +769,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00003E00)
 #endif	/* CONFIG_LWMON */
 
-/***  NX823  ***********************************************/
-
-#if defined(CONFIG_NX823)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET	PROFF_SCC2
-#define CPM_CR_ENET	CPM_CR_CH_SCC2
-#define SCC_ENET	1
-#define PA_ENET_RXD	((ushort)0x0004)  /* PA 13 */
-#define PA_ENET_TXD	((ushort)0x0008)  /* PA 12 */
-#define PA_ENET_RCLK	((ushort)0x0200)  /* PA  6 */
-#define PA_ENET_TCLK	((ushort)0x0800)  /* PA  4 */
-
-#define PB_ENET_TENA	((uint)0x00002000)   /* PB 18 */
-
-#define PC_ENET_CLSN	((ushort)0x0040)  /* PC  9 */
-#define PC_ENET_RENA	((ushort)0x0080)  /* PC  8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00002f00)
-
-#endif   /* CONFIG_NX823 */
-
-/***  MBX  ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
- * to the MBX860 board.  Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PC_ENET_TENA	((ushort)0x0001)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif	/* CONFIG_MBX */
-
 /***  KM8XX  *********************************************************/
 
 /* The KM8XX Service Module uses SCC3 for Ethernet */
@@ -1127,41 +954,6 @@ typedef struct scc_enet {
 
 #endif /* CONFIG_QS860T */
 
-/***  RPXCLASSIC  *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-
-#ifdef CONFIG_FEC_ENET
-
-# define FEC_ENET				/* use FEC for EThernet */
-# undef SCC_ENET
-
-#else	/* ! CONFIG_FEC_ENET */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00001000)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-
-#endif	/* CONFIG_FEC_ENET */
-
-#endif	/* CONFIG_RPXCLASSIC */
-
 /***  RPXLITE  ********************************************************/
 
 #ifdef CONFIG_RPXLITE
diff --git a/include/configs/ADS860.h b/include/configs/ADS860.h
deleted file mode 100644
index 82ea172d7a..0000000000
--- a/include/configs/ADS860.h
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860 ADS board.	 Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  *
-  * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
-  *
-  * Values common to all FADS family boards are in board/fads/fads.h
-  */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Board type */
-#define CONFIG_ADS		1	/* Old Motorola MPC821/860ADS */
-
-/* Processor type */
-#define CONFIG_MPC860		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1 */
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-
-#define CONFIG_BAUDRATE		38400	/* Console baudrate */
-
-#if 0
-#define CONFIG_SYS_8XX_FACT		1526	/* 32.768 kHz crystal on XTAL/EXTAL */
-#else
-#define CONFIG_SYS_8XX_FACT		12	/* 4 MHz oscillator on EXTCLK */
-#endif
-
-#define CONFIG_SYS_PLPRCR  (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) |	\
-		PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-#define CONFIG_DRAM_50MHZ		1
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_PING
-
-/* This is picked up again in fads.h */
-#define FADS_COMMANDS_ALREADY_DEFINED
-
-#include "../../board/fads/fads.h"
-
-#define CONFIG_SYS_PC_IDE_RESET	((ushort)0x0008)    /* PC 12	*/
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index b248302687..df371b771d 100644
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -14,10 +14,43 @@
 #define CONFIG_PHYS_64BIT
 
 #ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI	$(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW	$(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg
+#ifndef CONFIG_NAND
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
-#define CONFIG_SYS_FSL_PBL_PBI	board/freescale/b4860qds/b4_pbi.cfg
-#define CONFIG_SYS_FSL_PBL_RCW	board/freescale/b4860qds/b4_rcw.cfg
+#else
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW                 /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+#endif
 #endif
 
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
@@ -113,8 +146,8 @@
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR		0xffe20000
@@ -164,7 +197,16 @@ unsigned long get_board_ddr_clk(void);
 /*
  *  Config the L3 Cache as L3 SRAM
  */
-#define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		256 << 10
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_NAND
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(30 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
 
 #ifdef CONFIG_PHYS_64BIT
 #define CONFIG_SYS_DCSRBAR		0xf0000000
@@ -193,7 +235,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_SYS_FSL_DDR3
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_FSL_DDR_INTERACTIVE
+#endif
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS1	0x51
@@ -381,7 +425,11 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
 
 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
@@ -414,7 +462,7 @@ unsigned long get_board_ddr_clk(void);
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
@@ -435,7 +483,9 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
 #define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+#endif
 
 
 /* Use the HUSH parser */
@@ -596,7 +646,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -604,10 +654,10 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1130)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(13 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -617,10 +667,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h
index a163e3d8f1..5a316c83ad 100644
--- a/include/configs/BSC9131RDB.h
+++ b/include/configs/BSC9131RDB.h
@@ -220,7 +220,7 @@ extern unsigned long get_sdram_size(void);
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
 
 /* Serial Port */
diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index 052a0f1103..e76a04b262 100644
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -32,6 +32,13 @@
 #define CONFIG_SYS_TEXT_BASE		0x11000000
 #define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
 #endif
+#ifdef CONFIG_NAND_SECBOOT
+#define CONFIG_RAMBOOT_NAND
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
+#endif
 
 #ifdef CONFIG_NAND
 #define CONFIG_SPL
@@ -396,7 +403,7 @@ combinations. this should be removed later
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
 
 /* Serial Port */
@@ -551,7 +558,7 @@ combinations. this should be removed later
 #define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
 #define CONFIG_ENV_SECT_SIZE	0x10000
 #define CONFIG_ENV_SIZE		0x2000
-#elif defined(CONFIG_NAND)
+#elif defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT)
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
 #define CONFIG_ENV_OFFSET	((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
@@ -696,4 +703,6 @@ combinations. this should be removed later
 
 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
 
+#include <asm/fsl_secure_boot.h>
+
 #endif	/* __CONFIG_H */
diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h
index 92913c8e79..9e12fac5b1 100644
--- a/include/configs/C29XPCIE.h
+++ b/include/configs/C29XPCIE.h
@@ -338,7 +338,7 @@
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(2 * 1024 * 1024)
 
 /*
diff --git a/include/configs/EVB64260.h b/include/configs/EVB64260.h
deleted file mode 100644
index 8ec75d9618..0000000000
--- a/include/configs/EVB64260.h
+++ /dev/null
@@ -1,406 +0,0 @@
-/*
- * (C) Copyright 2001
- * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifndef __ASSEMBLY__
-#include <galileo/core.h>
-#endif
-
-#include "../board/evb64260/local.h"
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_EVB64260		1	/* this is an EVB64260 board	*/
-#define CONFIG_SYS_GT_6426x        GT_64260 /* with a 64260 system controller */
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff00000
-#define	CONFIG_SYS_LDSCRIPT	"board/evb64260/u-boot.lds"
-
-#define CONFIG_BAUDRATE		38400	/* console baudrate = 38400	*/
-
-#undef	CONFIG_ECC			/* enable ECC support */
-/* #define CONFIG_EVB64260_750CX  1 */      /* Support the EVB-64260-750CX Board */
-
-/* which initialization functions to call for this board */
-#define CONFIG_MISC_INIT_R	1
-#define CONFIG_BOARD_EARLY_INIT_F 1
-
-#ifndef CONFIG_EVB64260_750CX
-#define CONFIG_SYS_BOARD_NAME		"EVB64260"
-#else
-#define CONFIG_SYS_BOARD_NAME         "EVB64260-750CX"
-#endif
-
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * The following defines let you select what serial you want to use
- * for your console driver.
- *
- * what to do:
- * to use the DUART, undef CONFIG_MPSC.  If you have hacked a serial
- * cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1
- * to 0 below.
- *
- * to use the MPSC, #define CONFIG_MPSC.  If you have wired up another
- * mpsc channel, change CONFIG_MPSC_PORT to the desired value.
- */
-#define	CONFIG_MPSC
-#define CONFIG_MPSC_PORT	0
-
-
-/* define this if you want to enable GT MAC filtering */
-#define CONFIG_GT_USE_MAC_HASH_TABLE
-
-#undef CONFIG_ETHER_PORT_MII	/* use RMII */
-
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND						     \
-	"bootp && "						     \
-	"setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath " \
-	"ip=$ipaddr:$serverip:$gatewayip:" \
-	"$netmask:$hostname:eth0:none; && " \
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/
-#define	CONFIG_SYS_LOADS_BAUD_CHANGE		/* allow baudrate changes	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-#undef	CONFIG_ALTIVEC                  /* undef to disable             */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x00300000	/* default load address	*/
-#define CONFIG_SYS_BUS_CLK		100000000	/* 100 MHz		*/
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#ifdef CONFIG_EVB64260_750CX
-#define CONFIG_750CX
-#define CONFIG_SYS_BROKEN_CL2
-#endif
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_RAM_LOCK
-
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xfff00000
-#define CONFIG_SYS_RESET_ADDRESS	0xfff00100
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc */
-
-/* areas to map different things with the GT in physical space */
-#define CONFIG_SYS_DRAM_BANKS		4
-#define CONFIG_SYS_DFL_GT_REGS		0x14000000	/* boot time GT_REGS */
-
-/* What to put in the bats. */
-#define CONFIG_SYS_MISC_REGION_BASE	0xf0000000
-
-/* Peripheral Device section */
-#define CONFIG_SYS_GT_REGS		0xf8000000
-#define CONFIG_SYS_DEV_BASE		0xfc000000
-
-#define CONFIG_SYS_DEV0_SPACE		CONFIG_SYS_DEV_BASE
-#define CONFIG_SYS_DEV1_SPACE		(CONFIG_SYS_DEV0_SPACE + CONFIG_SYS_DEV0_SIZE)
-#define CONFIG_SYS_DEV2_SPACE		(CONFIG_SYS_DEV1_SPACE + CONFIG_SYS_DEV1_SIZE)
-#define CONFIG_SYS_DEV3_SPACE		(CONFIG_SYS_DEV2_SPACE + CONFIG_SYS_DEV2_SIZE)
-
-#define CONFIG_SYS_DEV0_SIZE		 _8M /* evb64260 sram  @ 0xfc00.0000 */
-#define CONFIG_SYS_DEV1_SIZE		 _8M /* evb64260 rtc   @ 0xfc80.0000 */
-#define CONFIG_SYS_DEV2_SIZE		_16M /* evb64260 duart @ 0xfd00.0000 */
-#define CONFIG_SYS_DEV3_SIZE		_16M /* evb64260 flash @ 0xfe00.0000 */
-
-#define CONFIG_SYS_DEV0_PAR		0x20205093
-#define CONFIG_SYS_DEV1_PAR		0xcfcfffff
-#define CONFIG_SYS_DEV2_PAR		0xc0059bd4
-#define CONFIG_SYS_8BIT_BOOT_PAR	0xc00b5e7c
-#define CONFIG_SYS_32BIT_BOOT_PAR	0xc4a8241c
-	/*   c    4    a      8     2     4    1      c		*/
-	/* 33 22|2222|22 22|111 1|11 11|1 1  |    |		*/
-	/* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210	*/
-	/* 11|00|0100|10 10|100|0 00|10 0|100 0|001 1|100	*/
-	/*  3| 0|.... ..| 2| 4 |  0 |  4 |  8  |  3  | 4	*/
-
-#if 0 /* Wrong?? NTL */
-#define CONFIG_SYS_MPP_CONTROL_0	0x53541717	/* InitAct EOT[4] DBurst TCEn[1] */
-						/* DMAAck[1:0] GNT0[1:0] */
-#else
-#define CONFIG_SYS_MPP_CONTROL_0	0x53547777	/* InitAct EOT[4] DBurst TCEn[1] */
-						/* REQ0[1:0] GNT0[1:0] */
-#endif
-#define CONFIG_SYS_MPP_CONTROL_1	0x44009911	/* TCEn[4] TCTcnt[4] GPP[13:12] */
-						/* DMAReq[4] DMAAck[4] WDNMI WDE */
-#if 0 /* Wrong?? NTL */
-#define CONFIG_SYS_MPP_CONTROL_2	0x40091818	/* TCTcnt[0] GPP[22:21] BClkIn */
-						/* DMAAck[1:0] GNT1[1:0] */
-#else
-#define CONFIG_SYS_MPP_CONTROL_2	0x40098888	/* TCTcnt[0] */
-						/* GPP[22] (RS232IntB or PCI1Int) */
-						/* GPP[21] (RS323IntA) */
-						/* BClkIn */
-						/* REQ1[1:0] GNT1[1:0] */
-#endif
-
-#if 0 /* Wrong?? NTL */
-# define CONFIG_SYS_MPP_CONTROL_3	0x00090066	/* GPP[31:29] BClkOut0 */
-						/* GPP[27:26] Int[1:0] */
-#else
-# define CONFIG_SYS_MPP_CONTROL_3	0x22090066      /* MREQ MGNT */
-						/* GPP[29]    (PCI1Int) */
-						/* BClkOut0 */
-						/* GPP[27]    (PCI0Int) */
-						/* GPP[26]    (RtcInt or PCI1Int) */
-						/* CPUInt[25:24] */
-#endif
-
-# define CONFIG_SYS_SERIAL_PORT_MUX	0x00000102	/* 0=hiZ  1=MPSC0 2=ETH 0 and 2 RMII */
-
-#if 0 /* Wrong?? - NTL */
-# define CONFIG_SYS_GPP_LEVEL_CONTROL	0x000002c6
-#else
-# define CONFIG_SYS_GPP_LEVEL_CONTROL	0x2c600000	/* 0010 1100 0110 0000 */
-						/* gpp[29] */
-						/* gpp[27:26] */
-						/* gpp[22:21] */
-
-# define CONFIG_SYS_SDRAM_CONFIG	0xd8e18200	/* 0x448 */
-				/* idmas use buffer 1,1
-				   comm use buffer 0
-				   pci use buffer 1,1
-				   cpu use buffer 0
-				   normal load (see also ifdef HVL)
-				   standard SDRAM (see also ifdef REG)
-				   non staggered refresh */
-				/* 31:26  25 23  20 19 18 16 */
-				/* 110110 00 111 0  0  00 1 */
-				/* refresh_count=0x200
-				   phisical interleaving disable
-				   virtual interleaving enable */
-				/* 15 14 13:0 */
-				/* 1  0  0x200 */
-#endif
-
-#define CONFIG_SYS_DUART_IO		CONFIG_SYS_DEV2_SPACE
-#define CONFIG_SYS_DUART_CHAN		1		/* channel to use for console */
-#define CONFIG_SYS_INIT_CHAN1
-#define CONFIG_SYS_INIT_CHAN2
-
-#define SRAM_BASE		CONFIG_SYS_DEV0_SPACE
-#define SRAM_SIZE		0x00100000		/* 1 MB of sram */
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-
-#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI                      /* include pci support          */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE  /* select pci host function     */
-#define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
-
-/* PCI MEMORY MAP section */
-#define CONFIG_SYS_PCI0_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI0_MEM_SIZE	_128M
-#define CONFIG_SYS_PCI1_MEM_BASE	0x88000000
-#define CONFIG_SYS_PCI1_MEM_SIZE	_128M
-
-#define CONFIG_SYS_PCI0_0_MEM_SPACE	(CONFIG_SYS_PCI0_MEM_BASE)
-#define CONFIG_SYS_PCI1_0_MEM_SPACE	(CONFIG_SYS_PCI1_MEM_BASE)
-
-
-/* PCI I/O MAP section */
-#define CONFIG_SYS_PCI0_IO_BASE	0xfa000000
-#define CONFIG_SYS_PCI0_IO_SIZE	_16M
-#define CONFIG_SYS_PCI1_IO_BASE	0xfb000000
-#define CONFIG_SYS_PCI1_IO_SIZE	_16M
-
-#define CONFIG_SYS_PCI0_IO_SPACE	(CONFIG_SYS_PCI0_IO_BASE)
-#define CONFIG_SYS_PCI0_IO_SPACE_PCI	0x00000000
-#define CONFIG_SYS_PCI1_IO_SPACE	(CONFIG_SYS_PCI1_IO_BASE)
-#define CONFIG_SYS_PCI1_IO_SPACE_PCI	0x00000000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-
-#define CONFIG_SYS_NS16550_REG_SIZE	-4
-
-#define CONFIG_SYS_NS16550_CLK		3686400
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_DUART_IO + 0)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_DUART_IO + 0x20)
-
-/*----------------------------------------------------------------------
- * Initial BAT mappings
- */
-
-/* NOTES:
- * 1) GUARDED and WRITE_THRU not allowed in IBATS
- * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
- */
-
-/* SDRAM */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* init ram */
-#define CONFIG_SYS_IBAT1L  (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U  (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT1L  CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U  CONFIG_SYS_IBAT1U
-
-/* PCI0, PCI1 in one BAT */
-#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
-#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* GT regs, bootrom, all the devices, PCI I/O */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* I2C speed and slave address (for compatability) defaults */
-#define CONFIG_SYS_I2C_SPEED	400000
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-
-/* I2C addresses for the two DIMM SPD chips */
-#ifndef CONFIG_EVB64260_750CX
-#define DIMM0_I2C_ADDR	0x56
-#define DIMM1_I2C_ADDR	0x54
-#else /* CONFIG_EVB64260_750CX - only has 1 DIMM */
-#define DIMM0_I2C_ADDR  0x54
-#define DIMM1_I2C_ADDR	0x54
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8<<20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks	*/
-#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max number of sectors on one chip */
-
-#define CONFIG_SYS_EXTRA_FLASH_DEVICE	DEVICE3	/* extra flash at device 3 */
-#define CONFIG_SYS_EXTRA_FLASH_WIDTH	4	/* 32 bit */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_FLASH_CFI		1
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_SIZE		0x1000	/* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE	0x10000
-#define CONFIG_ENV_ADDR    (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_MONITOR_LEN-CONFIG_ENV_SECT_SIZE)
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For all MPC74xx CPUs		 */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * L2CR setup -- make sure this is right for your board!
- * look in include/74xx_7xx.h for the defines used here
- */
-
-#define CONFIG_SYS_L2
-
-#ifdef CONFIG_750CX
-#define L2_INIT		0
-#else
-#define L2_INIT		(L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
-			 L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
-#endif
-
-#define L2_ENABLE	(L2_INIT | L2CR_L2E)
-
-#define CONFIG_SYS_BOARD_ASM_INIT      1
-
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h
deleted file mode 100644
index 50de4ea084..0000000000
--- a/include/configs/FADS823.h
+++ /dev/null
@@ -1,472 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia     io remapping
- * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by U-Boot
- * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * e0000000 -> f3ffffff : pcmcia     memory remapping by m8xx_pcmcia
- * fe000000 -> fe1fffff : flash      connected to CS0, setup by U-Boot
- * 00000000 -> nnnnnnnn : sdram/dram setup by U-Boot
-*/
-
-#define CONFIG_SYS_PCMCIA_IO_ADDR	0xff020000
-#define CONFIG_SYS_PCMCIA_IO_SIZE	0x10000
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	0xe0000000
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	0x10000
-#define CONFIG_SYS_IMMR		0xFF000000
-#define	CONFIG_SYS_SDRAM_SIZE		(4<<20) /* standard FADS has 4M */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x02800000
-#define BCSR_ADDR		((uint) 0xff010000)
-#define FLASH_BASE0_PRELIM	0x02800000	/* FLASH bank #0	*/
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define	CONFIG_ETHADDR		08:00:22:50:70:63	/* Ethernet address */
-#define CONFIG_ENV_OVERWRITE	1	/* Overwrite the environment */
-
-#define CONFIG_VIDEO		1	/* To enable video controller support */
-#define CONFIG_HARD_I2C		1	/* To I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*#define CONFIG_PCMCIA		1	/ * To enable PCMCIA support */
-
-/* Video related */
-
-#define CONFIG_VIDEO_LOGO			1	/* Show the logo */
-#define CONFIG_VIDEO_ENCODER_AD7176		1	/* Enable this encoder */
-#define CONFIG_VIDEO_ENCODER_AD7176_ADDR	0x54	/* Default on fads */
-#define CONFIG_VIDEO_SIZE			(2*1024*1024)
-/* #define CONFIG_VIDEO_ADDR (gd->bd->bi_memsize - CONFIG_VIDEO_SIZE) Frame buffer address */
-
-/* Wireless 56Khz 4PPM keyboard on SMCx */
-
-/*#define CONFIG_KEYBOARD		1 */
-#define CONFIG_WL_4PPM_KEYBOARD_SMC	0	/* SMC to use (0 indexed) */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC823		1
-#define CONFIG_MPC823FADS	1
-#define CONFIG_FADS		1
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		115200
-
-/* Set the CPU speed to 50Mhz on the FADS */
-
-#if 0
-#define MPC8XX_FACT	10			/* Multiply by 10		*/
-#define MPC8XX_XIN	5000000			/* 5 MHz in	*/
-#else
-#define MPC8XX_FACT	10			/* Multiply by 10 */
-#define MPC8XX_XIN	5000000			/* 5 MHz in */
-#define CONFIG_SYS_PLPRCR_MF	(MPC8XX_FACT-1) << 20	/* From 0 to 4095 */
-#endif
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds	*/
-#define CONFIG_LOADS_ECHO	0	/* Dont echoes received characters */
-#define CONFIG_BOOTARGS		""
-#define CONFIG_BOOTCOMMAND							\
-"bootp ;"									\
-"setenv bootargs console=tty0 console=ttyS0 "					\
-"root=/dev/nfs nfsroot=${serverip}:${rootpath} "				\
-"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:eth0:off ;"	\
-"bootm"
-#else
-#define CONFIG_BOOTDELAY	0	/* autoboot disabled		*/
-#endif
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_NISDOMAIN
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_TIMEOFFSET
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x01000000	/* 0 ... 16 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#if 0
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
-#define	CONFIG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration						11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer  *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CONFIG_SYS_PLPRCR_MF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR       (SCCR_TBS     | \
-				SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-				SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-				SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE1_PRELIM	0x00000000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFE00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xffff8110									/* 64Kbyte address space */
-#define CONFIG_SYS_BR1_PRELIM	((BCSR_ADDR) | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13a01114
-
-/* values according to the manual */
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_FLASH_PD_SHIFT	 28
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      23
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0           ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO               ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE            ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1           ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST            ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC850
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-#endif /* CONFIG_MPC850 */
-
-#define CONFIG_DRAM_50MHZ		1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC2_ENET 1
-#undef  CONFIG_FEC_ENET
-#undef  CONFIG_CPM_IIC
-#undef  CONFIG_UCODE_PATCH
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    1
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h
deleted file mode 100644
index d48460b9f5..0000000000
--- a/include/configs/FADS850SAR.h
+++ /dev/null
@@ -1,415 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/*
- * 1999-nov-26: The FADS is using the following physical memorymap:
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by 8xxrom
- * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * fe000000 -> ffnnnnnn : flash      connected to CS0, setup by 8xxrom
- * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC850		1
-#define CONFIG_MPC850SAR	1
-#define CONFIG_FADS			1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-
-#if 0
-#define MPC8XX_FACT	10				/* Multiply by 10		*/
-#define MPC8XX_XIN	50000000		/* 50 MHz in	*/
-#else
-#define MPC8XX_FACT	12				/* Multiply by 12 */
-#define MPC8XX_XIN	4000000			/* 4 MHz in */
-#endif
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BOOTCOMMAND	"bootm 02880000"	/* autoboot command */
-#define CONFIG_BOOTARGS		" "
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00800000	/* 0 ... 8 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFF000000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define	CONFIG_SYS_SDRAM_SIZE		(4<<20) /* standard FADS has 4M */
-#define CONFIG_SYS_FLASH_BASE		0x02800000
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#if 0
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 128 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x00040000	/* Offset of Environment Sector */
-#define	CONFIG_ENV_SIZE		0x40000	/* Total Size of Environment Sector	*/
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration						11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer  *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(((MPC8XX_FACT-1) << 20) | \
-				PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR       (SCCR_TBS     | \
-				SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-				SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-				SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR		((uint) 0x02100000)
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM	0x02800000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0x00000000	/* FLASH bank #1	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFE00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xffff8110									/* 64Kbyte address space */
-#define CONFIG_SYS_BR1_PRELIM	((BCSR_ADDR) | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13a01114
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR		((uint)0xff020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_FLASH_PD_SHIFT	 28
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      23
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG0           ((uint)0x04000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VCCO               ((uint)0x02000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHFDE            ((uint)0x02000000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC823
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHCFG1           ((uint)0x00400000)
-#endif /* CONFIG_MPC860T */
-#ifdef CONFIG_MPC823
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETHRST            ((uint)0x00200000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-
-#define CONFIG_DRAM_50MHZ		1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/FADS860T.h b/include/configs/FADS860T.h
deleted file mode 100644
index ed7484bd1c..0000000000
--- a/include/configs/FADS860T.h
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  *
-  * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
-  *
-  * Values common to all FADS family boards are in board/fads/fads.h
-  */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* board type */
-#define CONFIG_FADS		1       /* old/new FADS + new ADS */
-
-/* processor type */
-#define CONFIG_MPC860T		1       /* 860T */
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		38400
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-
-#if 0 /* old FADS */
-# define CONFIG_SYS_8XX_FACT		12	/* 4 MHz oscillator on EXTCLK */
-#else /* new FADS */
-# define CONFIG_SYS_8XX_FACT		10	/* 5 MHz oscillator on EXTCLK */
-#endif
-
-#define CONFIG_SYS_PLPRCR  (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) |	\
-		PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-#define CONFIG_DRAM_50MHZ		1
-#define CONFIG_SDRAM_50MHZ              1
-
-#include "../../board/fads/fads.h"
-
-#ifdef USE_REAL_FLASH_VALUES
-/*
- * These values fit our FADS860T ...
- * The "default" behaviour with 1Mbyte initial doesn't work for us!
- */
-#undef CONFIG_SYS_OR0_PRELIM
-#undef CONFIG_SYS_BR0_PRELIM
-#define CONFIG_SYS_OR0_PRELIM	0x0FFC00D34 /* Real values for the board */
-#define CONFIG_SYS_BR0_PRELIM	0x02800001  /* Real values for the board */
-#endif
-
-#define CONFIG_SYS_DAUGHTERBOARD /* FADS has processor-specific daughterboard */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/GENIETV.h b/include/configs/GENIETV.h
deleted file mode 100644
index 6a34b12bc6..0000000000
--- a/include/configs/GENIETV.h
+++ /dev/null
@@ -1,354 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T FADS board.  Copied from the MBX stuff.
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/*
- * The GENIETV is using the following physical memorymap (copied from
- * the FADS configuration):
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR       connected to CS1, setup by 8xxROM
- * ff000000 -> ff00ffff : IMAP       internal in the cpu
- * 30000000 -> 300fffff : flash      connected to CS0
- * 00000000 -> nnnnnnnn : sdram      setup by U-Boot
- *
- * CS pins are connected as follows:
- *
- * CS0 -512Kb boot flash
- * CS1 - SDRAM #1
- * CS2 - SDRAM #2
- * CS3 - Flash #1
- * CS4 - Flash #2
- * CS5 - Lon (if present)
- * CS6 - PCMCIA #1
- * CS7 - PCMCIA #2
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	CONFIG_SYS_TEXT_BASE	0x00000000
-
-#define	CONFIG_ETHADDR		08:00:22:50:70:63	/* Ethernet address */
-#define CONFIG_ENV_OVERWRITE	1	/* Overwrite the environment */
-
-#define CONFIG_SYS_ALLOC_DPRAM			/* Use dynamic DPRAM allocation */
-
-#define CONFIG_SYS_AUTOLOAD		"n"	/* No autoload */
-
-/*#define CONFIG_VIDEO		1	/  To enable the video initialization */
-/*#define CONFIG_VIDEO_ADDR	0x00200000 */
-/*#define CONFIG_HARD_I2C	1	/  I2C with hardware support */
-/*#define CONFIG_PCMCIA		1	/  To enable the PCMCIA initialization */
-
-/*#define CONFIG_SYS_PCMCIA_IO_ADDR	0xff020000 */
-/*#define CONFIG_SYS_PCMCIA_IO_SIZE	0x10000 */
-/*#define CONFIG_SYS_PCMCIA_MEM_ADDR	0xe0000000 */
-/*#define CONFIG_SYS_PCMCIA_MEM_SIZE	0x10000 */
-
-/* Video related */
-
-/*#define CONFIG_VIDEO_LOGO			1	/  Show the logo */
-/*#define CONFIG_VIDEO_ENCODER_AD7177		1	/  Enable this encoder */
-/*#define CONFIG_VIDEO_ENCODER_AD7177_ADDR	0xF4	/  ALSB to ground */
-
-/* Wireless 56Khz 4PPM keyboard on SMCx */
-
-/*#define CONFIG_KEYBOARD		0 */
-/*#define CONFIG_WL_4PPM_KEYBOARD_SMC	0	/  SMC to use (0 indexed) */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_GENIETV		1
-#define CONFIG_MPC823		1
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-
-#define MPC8XX_FACT	12			/* Multiply by 12	*/
-#define MPC8XX_XIN	5000000			/* 4 MHz clock		*/
-
-#define MPC8XX_HZ	((MPC8XX_XIN) * (MPC8XX_FACT))
-#define CONFIG_SYS_PLPRCR_MF	((MPC8XX_FACT-1) << 20)
-#define CONFIG_8xx_GCLK_FREQ	MPC8XX_HZ	/* Force it - dont measure it */
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_BOOTDELAY	1	/* autoboot after 2 seconds	*/
-#define CONFIG_LOADS_ECHO	0	/* Dont echoes received characters */
-#define CONFIG_BOOTARGS		""
-#define CONFIG_BOOTCOMMAND							\
-"bootp; tftp; "									\
-"setenv bootargs console=tty0 console=ttyS0 "					\
-"root=/dev/nfs nfsroot=${serverip}:${rootpath} "				\
-"ip=${ipaddr}:${serverip}:${gatewayip}:${subnetmask}:${hostname}:eth0:off ;"	\
-"bootm "
-#else
-#define CONFIG_BOOTDELAY	0	/* autoboot disabled		*/
-#endif
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		8		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00800000	/* 0 ... 8 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 4800, 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Also NOTE that it doesn't mean SDRAM - it means MEMORY.
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x02800000
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#if 0
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 128 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	8	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_OFFSET		0x10000	/* Offset of Environment Sector		*/
-#define	CONFIG_ENV_SIZE		0x10000	/* Total Size of Environment Sector (64k)*/
-
-/* values according to the manual */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control					11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration						11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- *
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC10)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control					11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register	15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer  *
- * interrupt status bit - leave PLL multiplication factor unchanged !
- *
- * #define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CONFIG_SYS_PLPRCR_MF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR       (SCCR_TBS     | \
-				SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-				SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-				SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0(FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x02800000	/* FLASH bank #0		*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask		*/
-#define CONFIG_SYS_PRELIM_OR_AM	0xFF800000	/* OR addr mask (512Kb) */
-
-/* FLASH timing */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
-				OR_SCY_15_CLK | OR_TRLX )
-
-/*#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH) */
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)		/* 0xfff80ff4 */
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8)	/* 0x02800401 */
-
-/*
- * BR1/2 and OR1/2 (SDRAM)
-*/
-
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
-
-#define SDRAM_MAX_SIZE		0x04000000	/* 64Mb bank */
-#define SDRAM_BASE1_PRELIM	0x00000000	/* First bank */
-#define SDRAM_BASE2_PRELIM	0x10000000	/* Second bank */
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MBMR_PTB		0x5d		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K        MPTPR_PTP_DIV32
-/*
- * MBMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MBMR_8COL	((CONFIG_SYS_MBMR_PTB << MAMR_PTA_SHIFT)  | MAMR_PTAE | \
-			MAMR_G0CLA_A11 | MAMR_RLFA_1X | MAMR_WLFA_1X \
-			| MAMR_TLFA_4X)	/* 0x5d802114 */
-
-/* values according to the manual */
-
-#define CONFIG_DRAM_50MHZ		1
-#define CONFIG_SDRAM_50MHZ
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    1
-#define PCMCIA_SLOT_B 1
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MBX.h b/include/configs/MBX.h
deleted file mode 100644
index 96edd442d0..0000000000
--- a/include/configs/MBX.h
+++ /dev/null
@@ -1,290 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the MBX8xx board.
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-/*
- * Changed 2002-10-01
- * Added PCMCIA defines mostly taken from other U-Boot boards that
- * have PCMCIA already working.  If you find any bugs, incorrect assumptions
- * feel free to fix them yourself and submit a patch.
- * Rod Boyce <rod_boyce@stratexnet.com.
- */
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
-#define CONFIG_MBX		1	/* ...on an MBX module		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-/* Define this to use the PCI bus */
-#undef CONFIG_USE_PCI
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-#define CONFIG_8xx_GCLK_FREQ    (50000000UL)
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 20000" /* autoboot command	*/
-
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
-				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
-				"nfsaddrs=10.0.0.99:10.0.0.2"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE   /* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#undef	CONFIG_SYS_HUSH_PARSER			/* Hush parse for U-Boot	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical memory map as defined by the MBX PGM
- */
-#define CONFIG_SYS_IMMR		0xFA200000 /* Internal Memory Mapped Register*/
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM			     */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers	     */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces	     */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers	     */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xfe000000
-#ifdef	DEBUG
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#endif
-#undef	CONFIG_SYS_MONITOR_BASE	/* 0x200000	   to run U-Boot from RAM */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC )
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define CONFIG_SYS_PCMCIA_INTERRUPT	SIU_LEVEL6
-
-#define CONFIG_PCMCIA_SLOT_A	1
-
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- * Debug Entry Mode
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MBX860T.h b/include/configs/MBX860T.h
deleted file mode 100644
index 74f44df682..0000000000
--- a/include/configs/MBX860T.h
+++ /dev/null
@@ -1,395 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T MBX board.
-  * Copied from the FADS stuff, which was originally copied from the MBX stuff!
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  * Rob Taylor coverted it back to MBX
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MBX		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define CONFIG_8xx_CPUCLOCK	40
-#define CONFIG_8xx_BUSCLOCK	(CONFIG_8xx_CPUCLOCK)
-#define TARGET_SYSTEM_FREQUENCY 40
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#define CONFIG_BAUDRATE		9600
-
-#define MPC8XX_FACT	10				/* Multiply by 10		*/
-#define MPC8XX_XIN	40000000		/* 50 MHz in	*/
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_8xx_BOOTDELAY	-1	/* autoboot disabled		*/
-#define CONFIG_8xx_TFTP_MODE
-#else
-#define CONFIG_8xx_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#undef	CONFIG_8xx_TFTP_MODE
-#endif
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_DRAM_SPEED	(CONFIG_8xx_BUSCLOCK)	/* MHz		*/
-#define CONFIG_BOOTCOMMAND	"bootm FE020000"	/* autoboot command */
-#define CONFIG_BOOTARGS		" "
-/*
- * Miscellaneous configurable options
- */
-#undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0800000	/* 4 ... 8 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFFA00000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM                          */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers       */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces      */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers       */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-/*0xFE000000*/
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_HWINFO_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR		((uint) 0xFF010000)
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0xFF010000	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFF00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	(0xFE000000 | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xFFC00000 | OR_ACS_DIV4
-#define CONFIG_SYS_BR1_PRELIM	(0x00000000 | BR_MS_UPMA | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13821000
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR		((uint)0xff020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      (23)
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#define BCSR4_VCCO               ((uint)0x02000000)
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-
-#define CONFIG_DRAM_40MHZ		1
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-#define CONFIG_CMD_NET
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC1_ENET 1
-#define CONFIG_FEC_ENET 1
-#undef  CONFIG_CPM_IIC
-#undef  CONFIG_UCODE_PATCH
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MOUSSE.h b/include/configs/MOUSSE.h
deleted file mode 100644
index e84d12f3f8..0000000000
--- a/include/configs/MOUSSE.h
+++ /dev/null
@@ -1,320 +0,0 @@
-/*
- * (C) Copyright 2000, 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * James F. Dougherty (jfd@cs.stanford.edu)
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- *
- * Configuration settings for the MOUSSE board.
- * See also: http://www.vooha.com/
- *
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC8240      1
-#define CONFIG_MOUSSE       1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-#define	CONFIG_SYS_LDSCRIPT	"board/mousse/u-boot.lds"
-
-#define CONFIG_SYS_ADDR_MAP_B      1
-
-#define CONFIG_CONS_INDEX   1
-#define CONFIG_BAUDRATE     9600
-#if 1
-#define CONFIG_BOOTCOMMAND  "tftp 100000 vmlinux.img;bootm"    /* autoboot command */
-#else
-#define CONFIG_BOOTCOMMAND  "bootm ffe10000"
-#endif
-#define CONFIG_BOOTARGS      "console=ttyS0 root=/dev/nfs rw nfsroot=209.128.93.133:/boot nfsaddrs=209.128.93.133:209.128.93.138"
-#define CONFIG_BOOTDELAY     3
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-
-
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_ETH_ADDR      "00:10:18:10:00:06"
-
-#define CONFIG_DOS_PARTITION  1 /* MSDOS bootable partitiion support */
-
-#include "../board/mousse/mousse.h"
-
-/*
- * Miscellaneous configurable options
- */
-#undef CONFIG_SYS_LONGHELP                /* undef to save memory     */
-#define CONFIG_SYS_CBSIZE      256        /* Console I/O Buffer Size  */
-#define CONFIG_SYS_PBSIZE      (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS     8           /* Max number of command args   */
-
-#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE  /* Boot Argument Buffer Size    */
-#define CONFIG_SYS_LOAD_ADDR   0x00100000  /* Default load address         */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE      0x00000000
-
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_SDRAM_BASE
-#else
-#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_FLASH_BASE
-#endif
-
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_LEN     (4 << 20)	/* lots of mem ... */
-#else
-#define CONFIG_SYS_MONITOR_LEN     (512 << 10)	/* 512K PLCC bootrom */
-#endif
-#define CONFIG_SYS_MALLOC_LEN      (2*(4096 << 10))    /* 2*4096kB for malloc()  */
-
-#define CONFIG_SYS_MEMTEST_START   0x00004000	/* memtest works on      */
-#define CONFIG_SYS_MEMTEST_END     0x02000000	/* 0 ... 32 MB in DRAM   */
-
-
-#define CONFIG_SYS_EUMB_ADDR       0xFC000000
-
-#define CONFIG_SYS_ISA_MEM         0xFD000000
-#define CONFIG_SYS_ISA_IO          0xFE000000
-
-#define CONFIG_SYS_FLASH_BASE      0xFFF00000
-#define CONFIG_SYS_FLASH_SIZE      ((uint)(512 * 1024))
-#define CONFIG_SYS_RESET_ADDRESS   0xFFF00100
-#define FLASH_BASE0_PRELIM  0xFFF00000  /* 512K PLCC FLASH/AM29F040*/
-#define FLASH_BASE0_SIZE    0x80000     /* 512K */
-#define FLASH_BASE1_PRELIM  0xFFE10000  /* AMD 29LV160DB
-					   1MB - 64K FLASH0 SEG =960K
-					   (size=0xf0000)*/
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#define CONFIG_SYS_NS16550_CLK		18432000
-
-#define CONFIG_SYS_NS16550_COM1	0xFFE08080
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MONITOR_LEN
-#define CONFIG_SYS_INIT_RAM_SIZE   0x2F00  /* Size of used area in DPRAM  */
-#define CONFIG_SYS_GBL_DATA_OFFSET  (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET  CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8240 user's manual.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33000000	/* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER  2
-
-#define CONFIG_SYS_ETH_DEV_FN       0x00
-#define CONFIG_SYS_ETH_IOBASE       0x00104000
-
-
-	/* Bit-field values for MCCR1.
-	 */
-#define CONFIG_SYS_ROMNAL          8
-#define CONFIG_SYS_ROMFAL          8
-
-	/* Bit-field values for MCCR2.
-	 */
-#define CONFIG_SYS_REFINT          0xf5     /* Refresh interval               */
-
-	/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4.
-	 */
-#define CONFIG_SYS_BSTOPRE         0x79
-
-#ifdef INCLUDE_ECC
-#define USE_ECC				1
-#else /* INCLUDE_ECC */
-#define USE_ECC				0
-#endif /* INCLUDE_ECC */
-
-
-	/* Bit-field values for MCCR3.
-	 */
-#define CONFIG_SYS_REFREC          8       /* Refresh to activate interval   */
-#define CONFIG_SYS_RDLAT           (4+USE_ECC)   /* Data latancy from read command */
-
-	/* Bit-field values for MCCR4.
-	 */
-#define CONFIG_SYS_PRETOACT        3       /* Precharge to activate interval */
-#define CONFIG_SYS_ACTTOPRE        5       /* Activate to Precharge interval */
-#define CONFIG_SYS_SDMODE_CAS_LAT  3       /* SDMODE CAS latancy             */
-#define CONFIG_SYS_SDMODE_WRAP     0       /* SDMODE wrap type               */
-#define CONFIG_SYS_SDMODE_BURSTLEN 2       /* SDMODE Burst length            */
-#define CONFIG_SYS_ACTORW          2
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER (1-USE_ECC)
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-#define CONFIG_SYS_RAM_SIZE        0x04000000  /* 64MB */
-
-
-#define CONFIG_SYS_BANK0_START     0x00000000
-#define CONFIG_SYS_BANK0_END       (CONFIG_SYS_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE    1
-#define CONFIG_SYS_BANK1_START     0x3ff00000
-#define CONFIG_SYS_BANK1_END       0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE    0
-#define CONFIG_SYS_BANK2_START     0x3ff00000
-#define CONFIG_SYS_BANK2_END       0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE    0
-#define CONFIG_SYS_BANK3_START     0x3ff00000
-#define CONFIG_SYS_BANK3_END       0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE    0
-#define CONFIG_SYS_BANK4_START     0x3ff00000
-#define CONFIG_SYS_BANK4_END       0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE    0
-#define CONFIG_SYS_BANK5_START     0x3ff00000
-#define CONFIG_SYS_BANK5_END       0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE    0
-#define CONFIG_SYS_BANK6_START     0x3ff00000
-#define CONFIG_SYS_BANK6_END       0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE    0
-#define CONFIG_SYS_BANK7_START     0x3ff00000
-#define CONFIG_SYS_BANK7_END       0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE    0
-
-#define CONFIG_SYS_ODCR            0x7f
-
-
-#define CONFIG_SYS_PGMAX           0x32 /* how long the 8240 reatins the currently accessed page in memory
-				    see 8240 book for details*/
-#define PCI_MEM_SPACE1_START	0x80000000
-#define PCI_MEM_SPACE2_START	0xfd000000
-
-/* IBAT/DBAT Configuration */
-/* Ram: 64MB, starts at address-0, r/w instruction/data */
-#define CONFIG_SYS_IBAT0U      (CONFIG_SYS_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT0L      (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_DBAT0U      CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT0L      CONFIG_SYS_IBAT0L
-
-/* MPLD/Port-X I/O Space : data and instruction read/write,  cache-inhibit */
-#define CONFIG_SYS_IBAT1U      (PORTX_DEV_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
-#if 0
-#define CONFIG_SYS_IBAT1L      (PORTX_DEV_BASE | BATL_PP_10  | BATL_MEMCOHERENCE |\
-			 BATL_WRITETHROUGH | BATL_CACHEINHIBIT)
-#else
-#define CONFIG_SYS_IBAT1L      (PORTX_DEV_BASE | BATL_PP_10 |BATL_CACHEINHIBIT)
-#endif
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-
-/* PCI Memory region 1: 0x8XXX_XXXX PCI Mem space: EUMBAR, etc - 16MB */
-#define CONFIG_SYS_IBAT2U	(PCI_MEM_SPACE1_START|BATU_BL_16M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L	(PCI_MEM_SPACE1_START|BATL_PP_10 | BATL_GUARDEDSTORAGE|BATL_CACHEINHIBIT)
-#define CONFIG_SYS_DBAT2U      CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT2L      CONFIG_SYS_IBAT2L
-
-/* PCI Memory region 2: PCI Devices in 0xFD space */
-#define CONFIG_SYS_IBAT3U	(PCI_MEM_SPACE2_START|BATU_BL_16M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT3L	(PCI_MEM_SPACE2_START|BATL_PP_10 | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_DBAT3U      CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT3L      CONFIG_SYS_IBAT3L
-
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ       (8 << 20)   /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS     3       /* Max number of flash banks         */
-#define CONFIG_SYS_MAX_FLASH_SECT      64      /* Max number of sectors in one bank */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT    120000  /* Timeout for Flash Erase (in ms)   */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Timeout for Flash Write (in ms)   */
-
-#if 0
-#define	CONFIG_ENV_IS_IN_FLASH	    1
-#define CONFIG_ENV_OFFSET          0x8000  /* Offset of the Environment Sector	*/
-#define CONFIG_ENV_SIZE            0x4000  /* Size of the Environment Sector    */
-#else
-#define CONFIG_ENV_IS_IN_NVRAM          1
-#define CONFIG_ENV_ADDR            NV_OFF_U_BOOT_ADDR /* PortX NVM Free addr*/
-#define CONFIG_ENV_OFFSET          CONFIG_ENV_ADDR
-#define CONFIG_ENV_SIZE            NV_U_BOOT_ENV_SIZE /* 2K */
-#endif
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE  16
-
-/* Localizations */
-#if 0
-#define CONFIG_ETHADDR          0:0:0:0:1:d
-#define CONFIG_IPADDR           172.16.40.113
-#define CONFIG_SERVERIP         172.16.40.111
-#else
-#define CONFIG_ETHADDR          0:0:0:0:1:d
-#define CONFIG_IPADDR           209.128.93.138
-#define CONFIG_SERVERIP         209.128.93.133
-#endif
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_PCI			/* include pci support			*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#undef CONFIG_PCI_PNP
-
-
-#define CONFIG_TULIP
-
-#endif  /* __CONFIG_H */
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
index faa5495cb4..f15e1626f0 100644
--- a/include/configs/MPC8536DS.h
+++ b/include/configs/MPC8536DS.h
@@ -31,13 +31,13 @@
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_RAMBOOT_SDCARD		1
-#define CONFIG_SYS_TEXT_BASE	0xf8f80000
+#define CONFIG_SYS_TEXT_BASE	0xf8f40000
 #define CONFIG_RESET_VECTOR_ADDRESS	0xf8fffffc
 #endif
 
 #ifdef CONFIG_SPIFLASH
 #define CONFIG_RAMBOOT_SPIFLASH		1
-#define CONFIG_SYS_TEXT_BASE	0xf8f80000
+#define CONFIG_SYS_TEXT_BASE	0xf8f40000
 #define CONFIG_RESET_VECTOR_ADDRESS	0xf8fffffc
 #endif
 
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index 58b9c26e93..5165a456aa 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -493,7 +493,7 @@ extern unsigned long get_clock_freq(void);
 
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xfff00000
+#define CONFIG_SYS_QE_FW_ADDR	0xfff00000
 
 /*
  * BOOTP options
diff --git a/include/configs/NX823.h b/include/configs/NX823.h
deleted file mode 100644
index 6d468dfcd1..0000000000
--- a/include/configs/NX823.h
+++ /dev/null
@@ -1,344 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU	    */
-#define CONFIG_NX823		1	/* ...on a NEXUS 823  module	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-/*#define  CONFIG_VIDEO		1 */
-
-#define CONFIG_8xx_GCLK_FREQ	MPC8XX_SPEED
-#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1	    */
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 57600	/* console baudrate = 115kbps	*/
-#define CONFIG_BOOTDELAY	2	/* autoboot after 2 seconds */
-#define CONFIG_BOOTARGS		"ramdisk_size=8000 "\
-				"root=/dev/nfs rw nfsroot=10.77.77.250:/ppcroot "\
-				"nfsaddrs=10.77.77.20:10.77.77.250"
-#define CONFIG_BOOTCOMMAND	"bootm 400e0000"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-#undef	CONFIG_WATCHDOG			/* watchdog disabled, for now	    */
-#define CONFIG_SOURCE
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_SOURCE
-
-
-/* call various generic functions */
-#define CONFIG_MISC_INIT_R
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#define CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks	    */
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)  */
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define xEMBED
-#ifdef	EMBED
-#define CONFIG_ENV_SIZE		0x200	/* FIXME How big when embedded?? */
-#define CONFIG_ENV_ADDR		CONFIG_SYS_MONITOR_BASE
-#else
-#define CONFIG_ENV_ADDR		0x40020000	/* absolute address for now   */
-#define CONFIG_ENV_SIZE		0x20000 /* 8K ouch, this may later be */
-#endif
-
-#define CONFIG_SYS_FLASH_SN_BASE	0x4001fff0	/* programmer automagically puts    */
-#define CONFIG_SYS_FLASH_SN_SECTOR	0x40000000	/* a serial number here		    */
-#define CONFIG_SYS_FLASH_SN_BYTES	8
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs		*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value    */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				12-30
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				12-16
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		12-18
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		12-23
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		5-7
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- */
-#define MPC8XX_SPEED	66666666L
-#define MPC8XX_XIN	32768	/* 32.768 kHz crystal */
-#define MPC8XX_FACT		(MPC8XX_SPEED/MPC8XX_XIN)
-#define CONFIG_SYS_PLPRCR_MF  ((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT)
-#define CONFIG_SYS_PLPRCR		(CONFIG_SYS_PLPRCR_MF | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		5-3
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0    */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV1 | OR_BI | \
-				 OR_SCY_8_CLK )
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-/*
- * BR1/2 and OR1/2 (SDRAM)
- */
-#define SDRAM_BASE1_PRELIM	0x00000000	/* SDRAM bank #0    */
-#define SDRAM_BASE2_PRELIM	0x20000000	/* SDRAM bank #1    */
-#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-/* SDRAM timing: Multiplexed addresses, drive GPL5 high on first cycle */
-#define CONFIG_SYS_OR_TIMING_SDRAM	(OR_G5LS | OR_CSNT_SAM)
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#define CONFIG_SYS_OR2_PRELIM	CONFIG_SYS_OR1_PRELIM
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* IO and memory mapped stuff */
-#define NX823_IO_OR_AM		0xFFFF0000	/* mask for IO addresses */
-#define NX823_IO_BASE		0xFF000000	/* start of IO	*/
-#define GPOUT_OFFSET		(3<<16)
-#define QUART_OFFSET		(4<<16)
-#define VIDAC_OFFSET		(5<<16)
-#define CPLD_OFFSET		(6<<16)
-#define SED1386_OFFSET		(7<<16)
-
-/*
- * BR3 and OR3 (general purpose output latches)
- */
-#define GPOUT_BASE	(NX823_IO_BASE + GPOUT_OFFSET)
-#define GPOUT_TIMING	(OR_CSNT_SAM | OR_TRLX | OR_BI)
-#define CONFIG_SYS_OR3_PRELIM	(NX823_IO_OR_AM | GPOUT_TIMING)
-#define CONFIG_SYS_BR3_PRELIM	(GPOUT_BASE | BR_V)
-
-/*
- * BR4 and OR4 (QUART)
- */
-#define QUART_BASE	(NX823_IO_BASE + QUART_OFFSET)
-#define QUART_TIMING	(OR_ACS_DIV4 | OR_SCY_3_CLK | OR_CSNT_SAM | OR_TRLX)
-#define CONFIG_SYS_OR4_PRELIM	(NX823_IO_OR_AM | QUART_TIMING | OR_BI)
-#define CONFIG_SYS_BR4_PRELIM	(QUART_BASE | BR_PS_8 | BR_V)
-
-/*
- * BR5 and OR5 (Video DAC)
- */
-#define VIDAC_BASE	(NX823_IO_BASE + VIDAC_OFFSET)
-#define VIDAC_TIMING	(OR_ACS_DIV4 | OR_SCY_3_CLK | OR_CSNT_SAM | OR_EHTR)
-#define CONFIG_SYS_OR5_PRELIM	(NX823_IO_OR_AM | VIDAC_TIMING | OR_BI)
-#define CONFIG_SYS_BR5_PRELIM	(VIDAC_BASE | BR_PS_8 | BR_V)
-
-/*
- * BR6 and OR6 (CPLD)
- * FIXME timing not verified for CPLD
- */
-#define CPLD_BASE	(NX823_IO_BASE + CPLD_OFFSET)
-#define CPLD_TIMING	(OR_ACS_DIV4 | OR_SCY_3_CLK | OR_CSNT_SAM | OR_EHTR)
-#define CONFIG_SYS_OR6_PRELIM	(NX823_IO_OR_AM | CPLD_TIMING | OR_BI)
-#define CONFIG_SYS_BR6_PRELIM	(CPLD_BASE | BR_PS_8 | BR_V )
-
-/*
- * BR7 and OR7 (SED1386)
- * FIXME timing not verified for SED controller
- */
-#define SED1386_BASE	0xF7000000
-#define CONFIG_SYS_OR7_PRELIM	(0xFF000000 | OR_BI | OR_SETA)
-#define CONFIG_SYS_BR7_PRELIM	(SED1386_BASE | BR_PS_16 | BR_V )
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	97		/* start with divider for 100 MHz   */
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16 /* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32 /* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8	/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16 /* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_ENV_OVERWRITE	/* allow changes to ethaddr (for now)	*/
-#define CONFIG_ETHADDR		00:10:20:30:40:50
-#define CONFIG_IPADDR		10.77.77.20
-#define CONFIG_SERVERIP		10.77.77.250
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index eabfc85f0f..d612a8b9c4 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -541,7 +541,8 @@ extern unsigned long get_sdram_size(void);
 					FTIM2_GPCM_TWP(0x1f))
 #define CONFIG_SYS_CS3_FTIM3		0x0
 
-#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH)
+#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \
+	defined(CONFIG_RAMBOOT_NAND)
 #define CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #else
@@ -549,8 +550,7 @@ extern unsigned long get_sdram_size(void);
 #endif
 
 #ifdef CONFIG_SYS_FSL_ERRATUM_IFC_A003399
-#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT)\
-	&& !defined(CONFIG_SECURE_BOOT)
+#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_A003399_NOR_WORKAROUND
 #endif
 #endif
@@ -566,7 +566,7 @@ extern unsigned long get_sdram_size(void);
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
 
 /*
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index 139d4fed25..959cdf69bb 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -352,7 +352,7 @@
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
 
 /*
diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h
index b41cb4a13e..ba3da06dfb 100644
--- a/include/configs/P1023RDB.h
+++ b/include/configs/P1023RDB.h
@@ -125,7 +125,7 @@ extern unsigned long get_clock_freq(void);
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)	  /* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)	  /* Reserve 512 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
 
 #define CONFIG_SYS_NAND_BASE		0xffa00000
@@ -360,7 +360,7 @@ extern unsigned long get_clock_freq(void);
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
index 2ffa3546de..8601eec85e 100644
--- a/include/configs/P1023RDS.h
+++ b/include/configs/P1023RDS.h
@@ -198,7 +198,7 @@ extern unsigned long get_clock_freq(void);
 	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN	(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
 
 #ifndef CONFIG_NAND_SPL
@@ -500,10 +500,10 @@ extern unsigned long get_clock_freq(void);
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x1f00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x1f00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
index 2ffaf5c0d9..0f04067258 100644
--- a/include/configs/P1_P2_RDB.h
+++ b/include/configs/P1_P2_RDB.h
@@ -238,7 +238,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 						- GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon*/
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
 
 #ifndef CONFIG_NAND_SPL
diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 3d0b5c2fbe..820b6332a6 100644
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -284,7 +284,7 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
 
 #define CONFIG_SYS_NAND_BASE		0xffa00000
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index b3880f190f..54e6493913 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -315,7 +315,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
@@ -506,7 +506,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -514,10 +514,10 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -527,10 +527,10 @@ unsigned long get_board_sys_clk(unsigned long dummy);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h
deleted file mode 100644
index 0f07d0cfe9..0000000000
--- a/include/configs/RPXClassic.h
+++ /dev/null
@@ -1,483 +0,0 @@
-/*
- * (C) Copyright 2000, 2001, 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
- * U-Boot port on RPXlite board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	RPXClassic_50MHz
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860           1
-#define CONFIG_RPXCLASSIC		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xff000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/
-
-/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1   */
-#define CONFIG_FEC_ENET
-#ifdef CONFIG_FEC_ENET
-#define CONFIG_SYS_DISCOVER_PHY        1
-#define CONFIG_MII              1
-#endif /* CONFIG_FEC_ENET */
-#define CONFIG_MISC_INIT_R
-
-/* Video console (graphic: Epson SED13806 on ECCX board, no keyboard         */
-#if 1
-#define CONFIG_VIDEO_SED13806
-#define CONFIG_NEC_NL6448BC20
-#define CONFIG_VIDEO_SED13806_16BPP
-
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_VIDEO_SW_CURSOR
-#endif
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK 1
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"tftpboot; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ELF
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_RESET_ADDRESS	0x80000000
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0040000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00C0000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFA200000
-
-/*-----------------------------------------------------------------------------
- * I2C Configuration
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_I2C_SPEED		50000
-#define CONFIG_SYS_I2C_SLAVE		0x34
-
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SYS_I2C_SOFT		/* I2C bit-banged		*/
-
-#if defined(CONFIG_SYS_I2C_SOFT)
-#define CONFIG_SYS_I2C			1
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define I2C_PORT	1		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00000010)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00000010)
-#define I2C_READ	((iop->pdat & 0x00000010) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00000010; \
-			else    iop->pdat &= ~0x00000010
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00000020; \
-			else    iop->pdat &= ~0x00000020
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x34
-#endif
-
-# define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
-# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE	0xFF000000
-
-#if defined(DEBUG) || defined (CONFIG_VIDEO_SED13806) || defined(CONFIG_CMD_IDE)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	0xFF000000
-/*%%% #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE */
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#if 0
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x20000	/*   Offset   of Environment Sector  */
-#define CONFIG_ENV_SECT_SIZE       0x8000
-#define	CONFIG_ENV_SIZE		0x8000	/* Total Size of Environment Sector  */
-#else
-#define CONFIG_ENV_IS_IN_NVRAM     1
-#define CONFIG_ENV_ADDR            0xfa000100
-#define CONFIG_ENV_SIZE            0x1000
-#endif
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_MLRC10)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC |  RTCSC_ALR | RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR	(SCCR_COM00 | SCCR_TBS)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/* #define	CONFIG_SYS_DER	0x2002000F */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE_PRELIM	0xFE000000	/* FLASH base */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
-
-/*
- * BR1 and OR1 (SDRAM)
- *
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
-#define	SDRAM_MAX_SIZE		0x01000000	/* max 16 MB */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000E00
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* RPXLITE mem setting */
-#define	CONFIG_SYS_BR3_PRELIM	0xFA400001		/* BCSR */
-#define CONFIG_SYS_OR3_PRELIM	0xff7f8970
-#define	CONFIG_SYS_BR4_PRELIM	0xFA000401		/* NVRAM&SRAM */
-#define CONFIG_SYS_OR4_PRELIM	0xFFF80970
-
-/* ECCX CS settings                                                          */
-#define SED13806_OR             0xFFC00108     /* - 4 Mo
-						   - Burst inhibit
-						   - external TA             */
-#define SED13806_REG_ADDR       0xa0000000
-#define SED13806_ACCES          0x801           /* 16 bit access             */
-
-
-/* Global definitions for the ECCX board                                     */
-#define ECCX_CSR_ADDR           (0xfac00000)
-#define ECCX_CSR8_OFFSET        (0x8)
-#define ECCX_CSR11_OFFSET       (0xB)
-#define ECCX_CSR12_OFFSET       (0xC)
-
-#define ECCX_CSR8  (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR8_OFFSET)
-#define ECCX_CSR11 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR11_OFFSET)
-#define ECCX_CSR12 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR12_OFFSET)
-
-
-#define REG_GPIO_CTRL 0x008
-
-/* Definitions for CSR8                                                      */
-#define ECCX_ENEPSON            0x80    /* Bit 0:
-					   0= disable and reset SED1386
-					   1= enable SED1386                 */
-/* Bit 1:   0= SED1386 in Big Endian mode                                    */
-/*          1= SED1386 in little endian mode                                 */
-#define ECCX_LE                 0x40
-#define ECCX_BE                 0x00
-
-/* Bit 2,3: Selection                                                        */
-/*      00 = Disabled                                                        */
-/*      01 = CS2 is used for the SED1386                                     */
-/*      10 = CS5 is used for the SED1386                                     */
-/*      11 = reserved                                                        */
-#define ECCX_CS2                0x10
-#define ECCX_CS5                0x20
-
-/* Definitions for CSR12                                                     */
-#define ECCX_ID                 0x02
-#define ECCX_860                0x01
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	58
-
-/*
- * Refresh clock Prescalar
- */
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
-			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
-
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-/* Configuration variable added by yooth. */
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-
-/*
- * BCSRx
- *
- * Board Status and Control Registers
- *
- */
-
-#define BCSR0 0xFA400000
-#define BCSR1 0xFA400001
-#define BCSR2 0xFA400002
-#define BCSR3 0xFA400003
-
-#define BCSR0_ENMONXCVR	0x01	/* Monitor XVCR Control */
-#define BCSR0_ENNVRAM	0x02	/* CS4# Control */
-#define BCSR0_LED5		0x04	/* LED5 control 0='on' 1='off' */
-#define BCSR0_LED4		0x08	/* LED4 control 0='on' 1='off' */
-#define BCSR0_FULLDPLX	0x10	/* Ethernet XCVR Control */
-#define BCSR0_COLTEST	0x20
-#define BCSR0_ETHLPBK	0x40
-#define BCSR0_ETHEN	0x80
-
-#define BCSR1_PCVCTL7	0x01	/* PC Slot B Control */
-#define BCSR1_PCVCTL6	0x02
-#define BCSR1_PCVCTL5	0x04
-#define BCSR1_PCVCTL4	0x08
-#define BCSR1_IPB5SEL	0x10
-
-#define BCSR2_MIIRST    0x80
-#define BCSR2_MIIPWRDWN 0x40
-#define BCSR2_MIICTL    0x08
-
-#define BCSR3_BWRTC		0x01	/* Real Time Clock Battery */
-#define BCSR3_BWNVR		0x02	/* NVRAM Battery */
-#define BCSR3_RDY_BSY	0x04	/* Flash Operation */
-#define BCSR3_RPXL		0x08	/* Reserved (reads back '1') */
-#define BCSR3_D27		0x10	/* Dip Switch settings */
-#define BCSR3_D26		0x20
-#define BCSR3_D25		0x40
-#define BCSR3_D24		0x80
-
-
-/*
- * Environment setting
- */
-
-/* #define CONFIG_ETHADDR	00:10:EC:00:2C:A2 */
-/* #define CONFIG_IPADDR	10.10.106.1 */
-/* #define CONFIG_SERVERIP	10.10.104.11 */
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h
deleted file mode 100644
index a28230a5d7..0000000000
--- a/include/configs/RPXlite.h
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
- * U-Boot port on RPXlite board
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	RPXLite_50MHz
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#undef CONFIG_MPC860
-#define CONFIG_MPC850		1	/* This is a MPC850 CPU		*/
-#define CONFIG_RPXLITE		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfff00000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"bootp; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#define CONFIG_BZIP2		/* Include support for bzip2 compressed images  */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	40000	/* 40 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
-/* Software (bit-bang) I2C driver configuration */
-#define PB_SCL		0x00000020	/* PB 26 */
-#define PB_SDA		0x00000010	/* PB 27 */
-
-#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)	if (bit) \
-				immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else \
-				immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-/* M41T11 Serial Access Timekeeper(R) SRAM */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-/* play along with the linux driver */
-#define CONFIG_SYS_M41T11_BASE_YEAR 1900
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_RESET_ADDRESS	0x09900000
-
-#define	CONFIG_SYS_LOAD_ADDR		0x400000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFA200000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFFC00000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#ifdef CONFIG_BZIP2
-#define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve ~4 MB for malloc()   */
-#else
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 KB for malloc()  */
-#endif /* CONFIG_BZIP2 */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_SYS_DIRECT_FLASH_TFTP
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SECT_SIZE	0x40000	/* We use one complete sector		*/
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-
-#define CONFIG_ENV_OVERWRITE
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | 0x00000600 | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_MLRC10)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	( (5 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF00
-/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_SCCR	(SCCR_COM11 | SCCR_TBS)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-/*#define	CONFIG_SYS_DER	0x2002000F*/
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE_PRELIM	0xFE000000	/* FLASH base */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */
-
-/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)
-
-/*
- * BR1 and OR1 (SDRAM)
- *
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
-#define	SDRAM_MAX_SIZE		0x01000000	/* max 16 MB */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000E00
-
-#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/* RPXLITE mem setting */
-#define	CONFIG_SYS_BR3_PRELIM	0xFA400001		/* BCSR */
-#define CONFIG_SYS_OR3_PRELIM	0xFFFF8910
-#define	CONFIG_SYS_BR4_PRELIM	0xFA000401		/* NVRAM&SRAM */
-#define CONFIG_SYS_OR4_PRELIM	0xFFFE0970
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	58
-
-/*
- * Refresh clock Prescalar
- */
-#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV8
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 10 column SDRAM */
-#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
-			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)
-
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-/* Configuration variable added by yooth. */
-/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
-
-/*
- * BCSRx
- *
- * Board Status and Control Registers
- *
- */
-
-#define BCSR0 0xFA400000
-#define BCSR1 0xFA400001
-#define BCSR2 0xFA400002
-#define BCSR3 0xFA400003
-
-#define BCSR0_ENMONXCVR	0x01	/* Monitor XVCR Control */
-#define BCSR0_ENNVRAM	0x02	/* CS4# Control */
-#define BCSR0_LED5	0x04	/* LED5 control 0='on' 1='off' */
-#define BCSR0_LED4	0x08	/* LED4 control 0='on' 1='off' */
-#define BCSR0_FULLDPLX	0x10	/* Ethernet XCVR Control */
-#define BCSR0_COLTEST	0x20
-#define BCSR0_ETHLPBK	0x40
-#define BCSR0_ETHEN	0x80
-
-#define BCSR1_PCVCTL7	0x01	/* PC Slot B Control */
-#define BCSR1_PCVCTL6	0x02
-#define BCSR1_PCVCTL5	0x04
-#define BCSR1_PCVCTL4	0x08
-#define BCSR1_IPB5SEL	0x10
-
-#define BCSR2_ENPA5HDR	0x08	/* USB Control */
-#define BCSR2_ENUSBCLK	0x10
-#define BCSR2_USBPWREN	0x20
-#define BCSR2_USBSPD	0x40
-#define BCSR2_USBSUSP	0x80
-
-#define BCSR3_BWRTC	0x01	/* Real Time Clock Battery */
-#define BCSR3_BWNVR	0x02	/* NVRAM Battery */
-#define BCSR3_RDY_BSY	0x04	/* Flash Operation */
-#define BCSR3_RPXL	0x08	/* Reserved (reads back '1') */
-#define BCSR3_D27	0x10	/* Dip Switch settings */
-#define BCSR3_D26	0x20
-#define BCSR3_D25	0x40
-#define BCSR3_D24	0x80
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h
deleted file mode 100644
index f5e0968011..0000000000
--- a/include/configs/RPXsuper.h
+++ /dev/null
@@ -1,501 +0,0 @@
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define	CONFIG_SYS_TEXT_BASE	0x80F00000
-
-/*****************************************************************************
- *
- * These settings must match the way _your_ board is set up
- *
- *****************************************************************************/
-/* for the AY-Revision which does not use the HRCW */
-#define CONFIG_SYS_DEFAULT_IMMR	0x00010000
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN  (66 * 1000 * 1000)
-
-/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
- * only the 3 least significant bits are important.
-*/
-#define CONFIG_SYS_SBC_S2  0x04
-
-/* What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Some example values (all frequencies are in MHz):
- *
- * MODCK_H   MODCK[1-3]  Osc    CPM    Core
- * 0x2       0x2         33     133    133
- * 0x2       0x4         33     133    200
- * 0x5       0x5         66     133    133
- * 0x5       0x7         66     133    200
- */
-#define CONFIG_SYS_SBC_MODCK_H 0x06
-
-#define CONFIG_SYS_SBC_BOOT_LOW 1	/* only for HRCW */
-#undef CONFIG_SYS_SBC_BOOT_LOW
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE.
- * The main FLASH is whichever is connected to *CS0. U-Boot expects
- * this to be the SIMM.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x80000000
-#define CONFIG_SYS_FLASH0_SIZE 16
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
- * want it enabled, don't define these constants.
- */
-#define CONFIG_SYS_FLASH1_BASE 0
-#define CONFIG_SYS_FLASH1_SIZE 0
-#undef CONFIG_SYS_FLASH1_BASE
-#undef CONFIG_SYS_FLASH1_SIZE
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM1_BASE 0x04000000
-#define CONFIG_SYS_SDRAM1_SIZE 32
-
-/* What should be the base address of the LEDs and switch S0?
- * If you don't want them enabled, don't define this.
- */
-#define CONFIG_SYS_LED_BASE 0x00000000
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC          /* define if console on SMC */
-#undef  CONFIG_CONS_ON_SCC          /* define if console on SCC */
-#undef  CONFIG_CONS_NONE            /* define if console on neither */
-#define CONFIG_CONS_INDEX    1      /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef  CONFIG_ETHER_ON_SCC           /* define if ethernet on SCC    */
-#define CONFIG_ETHER_ON_FCC           /* define if ethernet on FCC    */
-#undef  CONFIG_ETHER_NONE             /* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX      3     /* which SCC/FCC channel for ethernet */
-
-#if ( CONFIG_ETHER_INDEX == 3 )
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-/*#define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB) */
-# define CONFIG_SYS_FCC_PSMR		0
-
-#else /* CONFIG_ETHER_INDEX */
-# error "on RPX Super ethernet must be FCC3"
-#endif /* CONFIG_ETHER_INDEX */
-
-#define CONFIG_HARD_I2C         1	/* I2C with hardware support	*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-
-/* Define this to reserve an entire FLASH sector (256 KB) for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* What should the console's baud rate be? */
-#define CONFIG_BAUDRATE         115200
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR          08:00:22:50:70:63
-
-#define CONFIG_IPADDR		192.168.1.99
-#define CONFIG_SERVERIP         192.168.1.3
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY        -1
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt       */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#undef CONFIG_CMD_KGDB
-
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR               0xF0000000
-
-/* Where do the on board registers (CS4) live? */
-#define CONFIG_SYS_REGS_BASE          0xFA000000
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_RPXSUPER         1       /* on an Embedded Planet RPX Super Board  */
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
-#define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/
-
-/*
- * Miscellaneous configurable options
- */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CBSIZE              1024       /* Console I/O Buffer Size      */
-#else
-#  define CONFIG_SYS_CBSIZE              256        /* Console I/O Buffer Size      */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE        (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS       8            /* max number of command args   */
-
-#define CONFIG_SYS_BARGSIZE      CONFIG_SYS_CBSIZE   /* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START 0x04000000   /* memtest works on  */
-#define CONFIG_SYS_MEMTEST_END   0x06000000   /* 64-96 MB in SDRAM */
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_SYS_LOAD_ADDR     0x100000     /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE    CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_SDRAM_BASE    CONFIG_SYS_SDRAM0_BASE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
-#else
-#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (0)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
-			    ((CONFIG_SYS_IMMR & 0x01000000) >> 7)  |\
-			    ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11                           |\
-			 HRCW_DPPC11                          |\
-			 CONFIG_SYS_SBC_HRCW_IMMR                    |\
-			 HRCW_MMR00                           |\
-			 HRCW_LBPC11                          |\
-			 HRCW_APPC10                          |\
-			 HRCW_CS10PC00                        |\
-			 (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\
-			 CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE        0x4000  /* Size of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_FLASH0_BASE + 0x00F00000)
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#  define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN      (256 << 10)     /* Reserve 256 kB for Monitor   */
-#define CONFIG_SYS_MALLOC_LEN       (128 << 10)     /* Reserve 128 kB for malloc()  */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS   1       /* max number of memory banks         */
-#define CONFIG_SYS_MAX_FLASH_SECT    71      /* max number of sectors on one chip  */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT  8000    /* Timeout for Flash Erase (in ms)    */
-#define CONFIG_SYS_FLASH_WRITE_TOUT  1       /* Timeout for Flash Write (in ms)    */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#  define CONFIG_ENV_IS_IN_FLASH  1
-
-#  ifdef CONFIG_ENV_IN_OWN_SECT
-#    define CONFIG_ENV_ADDR       (CONFIG_SYS_MONITOR_BASE + 0x40000)
-#    define CONFIG_ENV_SECT_SIZE  0x40000
-#  else
-#    define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-#    define CONFIG_ENV_SIZE       0x1000  /* Total Size of Environment Sector */
-#    define CONFIG_ENV_SECT_SIZE  0x10000 /* see README - env sect real size */
-#  endif /* CONFIG_ENV_IN_OWN_SECT */
-#else
-#  define CONFIG_ENV_IS_IN_NVRAM  1
-#  define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#  define CONFIG_ENV_SIZE         0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT     5     /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers                    2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT   (/*HID0_ICE  |*/\
-			 /*HID0_DCE  |*/\
-			 HID0_ICFI |\
-			 HID0_DCI  |\
-			 HID0_IFEM |\
-			 HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL  (/*HID0_ICE  |*/\
-			 HID0_IFEM |\
-			 HID0_ABE  |\
-			 HID0_EMCP)
-#define CONFIG_SYS_HID2        0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR         0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration                                       4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR         (BCR_EBM   |\
-			 BCR_PLDP  |\
-			 BCR_EAV   |\
-			 BCR_NPQM0)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration                             4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR      (SIUMCR_L2CPC01 |\
-			 SIUMCR_APPC10  |\
-			 SIUMCR_CS10PC01)
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control                            11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC |\
-			 SYPCR_BMT  |\
-			 SYPCR_PBME |\
-			 SYPCR_LBME |\
-			 SYPCR_SWRI |\
-			 SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC |\
-			 TMCNTSC_ALR |\
-			 TMCNTSC_TCF |\
-			 TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR       (PISCR_PS  |\
-			 PISCR_PTF |\
-			 PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control                                   9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR        (SCCR_DFBRG01)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM    64 bit  FLASH (BGA - 16MB AMD AM29DL323DB90)
- *  1   60x     SDRAM   64 bit  SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
- *  2   Local   SDRAM   32 bit  SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
- *  3   unused
- *  4   60x     GPCM     8 bit  Board Regs, LEDs, switches
- *  5   unused
- *  6   unused
- *  7   unused
- *  8   PCMCIA
- *  9   unused
- * 10   unused
- * 11   unused
-*/
-
-/* Bank 0 - FLASH
- *
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64                      |\
-			 BRx_DECC_NONE                  |\
-			 BRx_MS_GPCM_P                  |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE)     |\
-			 ORxG_CSNT                      |\
-			 ORxG_ACS_DIV1                  |\
-			 ORxG_SCY_6_CLK                 |\
-			 ORxG_EHTR)
-
-/* Bank 1 - SDRAM
- *
- */
-#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE)     |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI0_A8             |\
-			 ORxS_NUMR_12                   |\
-			 ORxS_IBID)
-
-#define CONFIG_SYS_PSDMR       0x014DA412
-#define CONFIG_SYS_PSRT	0x79
-
-
-/* Bank 2 - SDRAM
- *
- */
-#define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
-			 BRx_PS_32                      |\
-			 BRx_MS_SDRAM_L                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE)     |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI0_A9             |\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_LSDMR       0x0169A512
-#define CONFIG_SYS_LSRT	0x79
-
-#define CONFIG_SYS_MPTPR	(0x0800 & MPTPR_PTP_MSK)
-
-/* Bank 4 - On board registers
- *
- */
-#define CONFIG_SYS_BR4_PRELIM   ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK)  |\
-			   BRx_PS_8                     |\
-			   BRx_MS_GPCM_P                |\
-			   BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM    (ORxG_AM_MSK                 |\
-			   ORxG_CSNT                   |\
-			   ORxG_ACS_DIV1               |\
-			   ORxG_SCY_5_CLK              |\
-			   ORxG_TRLX)
-
-#endif  /* __CONFIG_H */
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index 993f9ae533..522653bdc3 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -43,6 +43,10 @@
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MP			/* support multiple processors */
 
+/* support deep sleep */
+#define CONFIG_DEEP_SLEEP
+#define CONFIG_SILENT_CONSOLE
+
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xeff40000
 #endif
@@ -169,8 +173,10 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
+#ifndef CONFIG_SYS_FSL_DDR4
 #define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
+#endif
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS	0x51
@@ -374,7 +380,7 @@ unsigned long get_board_ddr_clk(void);
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(10 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
@@ -595,6 +601,8 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_DPAA_PME
 
+#define CONFIG_QE
+#define CONFIG_U_QE
 /* Default address of microcode for the Linux Fman driver */
 #if defined(CONFIG_SPIFLASH)
 /*
@@ -602,7 +610,7 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -610,13 +618,14 @@ unsigned long get_board_ddr_clk(void);
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_QE_FW_ADDR		0xEFF10000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
@@ -649,6 +658,23 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 /*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+			"spi0=spife110000.0"
+#define MTDPARTS_DEFAULT	"mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+				"128k(dtb),96m(fs),-(user);"\
+				"fff800000.flash:2m(uboot),9m(kernel),"\
+				"128k(dtb),96m(fs),-(user);spife110000.0:" \
+				"2m(uboot),9m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
  * Environment
  */
 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h
deleted file mode 100644
index 395845bd68..0000000000
--- a/include/configs/T1040RDB.h
+++ /dev/null
@@ -1,687 +0,0 @@
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * T1040 RDB board configuration file
- */
-#define CONFIG_T104xRDB
-#define CONFIG_T1040RDB
-#define CONFIG_PHYS_64BIT
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500			/* BOOKE e500 family */
-#define CONFIG_E500MC			/* BOOKE e500mc family */
-#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
-#define CONFIG_MP			/* support multiple processors */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC			/* Enable IFC Support */
-#define CONFIG_PCI			/* Enable PCI/PCIE */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE1			/* PCIE controler 1 */
-#define CONFIG_PCIE2			/* PCIE controler 2 */
-#define CONFIG_PCIE3			/* PCIE controler 3 */
-#define CONFIG_PCIE4			/* PCIE controler 4 */
-
-#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
-
-#define CONFIG_FSL_LAW			/* Use common FSL init code */
-
-#define CONFIG_ENV_OVERWRITE
-
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#ifndef CONFIG_SYS_NO_FLASH
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
-#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
-#define CONFIG_ENV_SECT_SIZE            0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV          0
-#define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(512 * 1658)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-#endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE                0x2000
-#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	100000000
-#define CONFIG_DDR_CLK_FREQ	66666666
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
-#define CONFIG_BTB			/* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
-#endif
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_ADDR_MAP
-#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
-
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00400000
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_PANIC_HANG	/* do not reset board on panic */
-
-/*
- *  Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
-
-#define CONFIG_SYS_DCSRBAR		0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_FSL_DDR3
-
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS	0x51
-
-#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE	0xe8000000
-#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-
-#define CONFIG_SYS_NOR_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NOR_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
-				CSPR_PORT_SIZE_16 | \
-				CSPR_MSEL_NOR | \
-				CSPR_V)
-#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
-#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
-				FTIM0_NOR_TEADC(0x5) | \
-				FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
-				FTIM1_NOR_TRAD_NOR(0x1A) |\
-				FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
-				FTIM2_NOR_TCH(0x4) | \
-				FTIM2_NOR_TWPH(0x0E) | \
-				FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3	0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
-
-/* CPLD on IFC */
-#define CONFIG_SYS_CPLD_BASE	0xffdf0000
-#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
-#define CONFIG_SYS_CSPR2_EXT	(0xf)
-#define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 \
-				| CSPR_MSEL_GPCM \
-				| CSPR_V)
-#define CONFIG_SYS_AMASK2	IFC_AMASK(64*1024)
-#define CONFIG_SYS_CSOR2	0x0
-/* CPLD Timing parameters for IFC CS2 */
-#define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
-					FTIM0_GPCM_TEADC(0x0e) | \
-					FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
-					FTIM1_GPCM_TRAD(0x1f))
-#define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
-					FTIM2_GPCM_TCH(0x0) | \
-					FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS2_FTIM3		0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE		0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
-				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
-				| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
-				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
-				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
-				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
-				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
-				| CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
-				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
-					FTIM0_NAND_TWP(0x18)   | \
-					FTIM0_NAND_TWCHT(0x07) | \
-					FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
-					FTIM1_NAND_TWBE(0x39)  | \
-					FTIM1_NAND_TRR(0x0e)   | \
-					FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
-					FTIM2_NAND_TREH(0x0a) | \
-					FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3		0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW		11
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_R
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
-	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
-	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_CONS_INDEX	1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
-#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL		/* Use FSL common I2C driver */
-#define CONFIG_SYS_FSL_I2C_SPEED	400000	/* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000	/* I2C speed in Hz */
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x119000
-
-/* I2C bus multiplexer */
-#define I2C_MUX_PCA_ADDR                0x70
-#define I2C_MUX_CH_DEFAULT      0x8
-
-
-/*
- * eSPI - Enhanced SPI
- */
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED         10000000
-#define CONFIG_SF_DEFAULT_MODE          0
-#define CONFIG_ENV_SPI_BUS              0
-#define CONFIG_ENV_SPI_CS               0
-#define CONFIG_ENV_SPI_MAX_HZ           10000000
-#define CONFIG_ENV_SPI_MODE             0
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-#ifdef CONFIG_PCI
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#ifdef CONFIG_PCIE1
-#define	CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
-#define	CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
-#define	CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-#endif
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#ifdef CONFIG_PCIE2
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0x90000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc10000000ull
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-#endif
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#ifdef CONFIG_PCIE3
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-#endif
-
-/* controller 4, Base address 203000 */
-#ifdef CONFIG_PCIE4
-#define CONFIG_SYS_PCIE4_MEM_VIRT	0xb0000000
-#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc30000000ull
-#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE4_IO_VIRT	0xf8030000
-#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
-#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
-#endif
-
-#define CONFIG_PCI_PNP			/* do pci plug-and-play */
-#define CONFIG_E1000
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#endif	/* CONFIG_PCI */
-
-/* SATA */
-#define CONFIG_FSL_SATA_V2
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-
-#define CONFIG_SYS_SATA_MAX_DEVICE	1
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
-
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
-* USB
-*/
-#define CONFIG_HAS_FSL_DR_USB
-
-#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#endif
-#endif
-
-#define CONFIG_MMC
-
-#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS	25
-#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS	25
-#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_REALTEK
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_SGMII1_PHY_ADDR		0x03
-#define CONFIG_SYS_RGMII1_PHY_ADDR		0x01
-#define CONFIG_SYS_RGMII2_PHY_ADDR		0x02
-
-#define CONFIG_MII		/* MII PHY management */
-#define CONFIG_ETHPRIME		"FM1@DTSEC4"
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
-#endif
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SETEXPR
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
-#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
-#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-
-#define CONFIG_BOOTDELAY	10	/*-1 disables auto-boot*/
-
-#define CONFIG_BAUDRATE	115200
-
-#define __USB_PHY_TYPE	utmi
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-	"hwconfig=fsl_ddr:bank_intlv=cs0_cs1;"			\
-	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
-	"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
-	"netdev=eth0\0"						\
-	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
-	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
-	"tftpflash=tftpboot $loadaddr $uboot && "		\
-	"protect off $ubootaddr +$filesize && "			\
-	"erase $ubootaddr +$filesize && "			\
-	"cp.b $loadaddr $ubootaddr $filesize && "		\
-	"protect on $ubootaddr +$filesize && "			\
-	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
-	"consoledev=ttyS0\0"					\
-	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=t1040rdb/ramdisk.uboot\0"			\
-	"fdtaddr=c00000\0"					\
-	"fdtfile=t1040rdb/t1040rdb.dtb\0"			\
-	"bdev=sda3\0"						\
-	"c=ffe\0"
-
-#define CONFIG_LINUX                       \
-	"setenv bootargs root=/dev/ram rw "            \
-	"console=$consoledev,$baudrate $othbootargs;"  \
-	"setenv ramdiskaddr 0x02000000;"               \
-	"setenv fdtaddr 0x00c00000;"		       \
-	"setenv loadaddr 0x1000000;"		       \
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND			\
-	"setenv bootargs root=/dev/nfs rw "	\
-	"nfsroot=$serverip:$rootpath "		\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"		\
-	"tftp $fdtaddr $fdtfile;"		\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $ramdiskaddr $ramdiskfile;"		\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#endif
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T104xRDB.h
index 68656e6ef1..81b4f31bc6 100644
--- a/include/configs/T1042RDB_PI.h
+++ b/include/configs/T104xRDB.h
@@ -1,38 +1,92 @@
 /*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
++ * Copyright 2014 Freescale Semiconductor, Inc.
++ *
++ * SPDX-License-Identifier:     GPL-2.0+
++ */
 
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
 /*
- * T1042RDB_PI board configuration file
+ * T104x RDB board configuration file
  */
 #define CONFIG_T104xRDB
-#define CONFIG_T1042RDB_PI
 #define CONFIG_PHYS_64BIT
 
 #ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg
+#ifdef CONFIG_T1040RDB
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1040_rcw.cfg
+#endif
+#ifdef CONFIG_T1042RDB_PI
+#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_rcw.cfg
+#endif
+
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW                 /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST		(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
 #endif
 
 /* High Level Configuration Options */
@@ -42,6 +96,10 @@
 #define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
 #define CONFIG_MP			/* support multiple processors */
 
+/* support deep sleep */
+#define CONFIG_DEEP_SLEEP
+#define CONFIG_SILENT_CONSOLE
+
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xeff40000
 #endif
@@ -67,15 +125,12 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#ifdef CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_NOWHERE
-#else
+#ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 #endif
 
-#ifndef CONFIG_SYS_NO_FLASH
 #if defined(CONFIG_SPIFLASH)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_SPI_FLASH
@@ -87,11 +142,11 @@
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV          0
 #define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(512 * 1658)
+#define CONFIG_ENV_OFFSET		(512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE			0x2000
 #define CONFIG_ENV_OFFSET		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_ENV_IS_IN_FLASH
@@ -99,10 +154,6 @@
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
 #endif
-#else /* CONFIG_SYS_NO_FLASH */
-#define CONFIG_ENV_SIZE                0x2000
-#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
-#endif
 
 #define CONFIG_SYS_CLK_FREQ	100000000
 #define CONFIG_DDR_CLK_FREQ	66666666
@@ -134,6 +185,15 @@
  *  Config the L3 Cache as L3 SRAM
  */
 #define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		256 << 10
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(30 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
 
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
@@ -196,6 +256,14 @@
 #define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
 
 /* CPLD on IFC */
+#define CPLD_LBMAP_MASK			0x3F
+#define CPLD_BANK_SEL_MASK		0x07
+#define CPLD_BANK_OVERRIDE		0x40
+#define CPLD_LBMAP_ALTBANK		0x44 /* BANK OR | BANK 4 */
+#define CPLD_LBMAP_DFLTBANK		0x40 /* BANK OR | BANK0 */
+#define CPLD_LBMAP_RESET		0xFF
+#define CPLD_LBMAP_SHIFT		0x03
+
 #define CONFIG_SYS_CPLD_BASE	0xffdf0000
 #define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 #define CONFIG_SYS_CSPR2_EXT	(0xf)
@@ -296,7 +364,11 @@
 #define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
 #endif
 
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
 
 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
@@ -323,7 +395,7 @@
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
@@ -344,7 +416,9 @@
 #define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
 #define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
 #define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+#endif
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
@@ -371,7 +445,11 @@
 
 /* I2C bus multiplexer */
 #define I2C_MUX_PCA_ADDR                0x70
+#ifdef CONFIG_T1040RDB
+#define I2C_MUX_CH_DEFAULT      0x8
+#endif
 
+#ifdef CONFIG_T1042RDB_PI
 /*
  * RTC configuration
  */
@@ -381,6 +459,7 @@
 
 /*DVI encoder*/
 #define CONFIG_HDMI_ENCODER_I2C_ADDR  0x75
+#endif
 
 /*
  * eSPI - Enhanced SPI
@@ -518,6 +597,11 @@
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_SYS_DPAA_PME
 
+#ifdef CONFIG_T1040RDB
+#define CONFIG_QE
+#define CONFIG_U_QE
+#endif
+
 /* Default address of microcode for the Linux Fman driver */
 #if defined(CONFIG_SPIFLASH)
 /*
@@ -525,22 +609,36 @@
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 0x820)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
+#endif
+
+#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_QE_FW_ADDR		0x130000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_QE_FW_ADDR		(512 * 0x920)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FW_ADDR		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FW_ADDR		0xEFF10000
+#endif
 #endif
+
+
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 #endif /* CONFIG_NOBQFMAN */
@@ -552,6 +650,9 @@
 #endif
 
 #ifdef CONFIG_FMAN_ENET
+#ifdef CONFIG_T1040RDB
+#define CONFIG_SYS_SGMII1_PHY_ADDR		0x03
+#endif
 #define CONFIG_SYS_RGMII1_PHY_ADDR		0x01
 #define CONFIG_SYS_RGMII2_PHY_ADDR		0x02
 
@@ -571,7 +672,9 @@
  */
 #include <config_cmd_default.h>
 
+#ifdef CONFIG_T1042RDB_PI
 #define CONFIG_CMD_DATE
+#endif
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
@@ -618,6 +721,23 @@
 #endif
 
 /*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+			"spi0=spife110000.0"
+#define MTDPARTS_DEFAULT	"mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+				"128k(dtb),96m(fs),-(user);"\
+				"fff800000.flash:2m(uboot),9m(kernel),"\
+				"128k(dtb),96m(fs),-(user);spife110000.0:" \
+				"2m(uboot),9m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
  * Environment Configuration
  */
 #define CONFIG_ROOTPATH		"/opt/nfsroot"
@@ -633,6 +753,14 @@
 
 #define __USB_PHY_TYPE	utmi
 
+#ifdef CONFIG_T1040RDB
+#define FDTFILE		"t1040rdb/t1040rdb.dtb"
+#define RAMDISKFILE	"t1040rdb/ramdisk.uboot"
+#elif CONFIG_T1042RDB_PI
+#define FDTFILE		"t1040rdb_pi/t1040rdb_pi.dtb"
+#define RAMDISKFILE	"t1040rdb_pi/ramdisk.uboot"
+#endif
+
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
 	"hwconfig=fsl_ddr:bank_intlv=cs0_cs1;"			\
 	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
@@ -648,9 +776,9 @@
 	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=t1040rdb_pi/ramdisk.uboot\0"			\
+	"ramdiskfile=" __stringify(RAMDISKFILE) "\0"		\
 	"fdtaddr=c00000\0"					\
-	"fdtfile=t1040rdb_pi/t1040rdb_pi.dtb\0"				\
+	"fdtfile=" __stringify(FDTFILE) "\0"			\
 	"bdev=sda3\0"						\
 	"c=ffe\0"
 
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 399ddbb791..8bf08430be 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -46,15 +46,79 @@
 #define CONFIG_ENV_OVERWRITE
 
 #ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xqds/t208x_pbi.cfg
 #if defined(CONFIG_PPC_T2080)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_rcw.cfg
 #elif defined(CONFIG_PPC_T2081)
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_rcw.cfg
 #endif
+
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST		(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
 #endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define	CONFIG_RESET_VECTOR_ADDRESS		0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START	(0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#endif /* CONFIG_RAMBOOT_PBL */
 
 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
@@ -85,11 +149,7 @@
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-#else
+#ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
@@ -110,12 +170,12 @@
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV	0
 #define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_OFFSET	(512 * 1658)
+#define CONFIG_ENV_OFFSET	(512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET	(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_OFFSET	(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR		0xffe20000
@@ -140,7 +200,16 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Config the L3 Cache as L3 SRAM
  */
-#define CONFIG_SYS_INIT_L3_ADDR	 CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		(512 << 10)
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(50 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
 
 #define CONFIG_SYS_DCSRBAR	0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull
@@ -298,8 +367,16 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
@@ -315,6 +392,14 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
@@ -324,20 +409,17 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
 #endif
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 
 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_SYS_MONITOR_BASE	 CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
 #define CONFIG_MISC_INIT_R
 #define CONFIG_HWCONFIG
@@ -356,7 +438,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 						GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 /*
@@ -453,15 +535,14 @@ unsigned long get_board_ddr_clk(void);
  */
 #ifdef CONFIG_SPI_FLASH
 #define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SST
 #define CONFIG_SPI_FLASH_STMICRO
-#if defined(CONFIG_T2080QDS)
-#define CONFIG_SPI_FLASH_SPANSION
-#elif defined(CONFIG_T2081QDS)
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SPI_FLASH_SST
 #define CONFIG_SPI_FLASH_EON
 #endif
 
 #define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_BAR
 #define CONFIG_SF_DEFAULT_SPEED	 10000000
 #define CONFIG_SF_DEFAULT_MODE	  0
 #endif
@@ -552,18 +633,18 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 0x820)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(11 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -573,10 +654,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
@@ -649,6 +730,23 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_DOS_PARTITION
 #endif
 
+
+/*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+			"spi0=spife110000.0"
+#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+			"128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
+			"5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \
+			"1m(uboot),5m(kernel),128k(dtb),-(user)"
+#endif
+
 /*
  * Environment
  */
diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h
index 743eee3161..73d82edb80 100644
--- a/include/configs/T208xRDB.h
+++ b/include/configs/T208xRDB.h
@@ -39,11 +39,75 @@
 #define CONFIG_ENV_OVERWRITE
 
 #ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg
+
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
+#define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
 #endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
+#define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#endif /* CONFIG_RAMBOOT_PBL */
 
 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
@@ -74,11 +138,7 @@
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
 #endif
 
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-#else
+#ifndef CONFIG_SYS_NO_FLASH
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
@@ -99,11 +159,11 @@
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV	0
 #define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_OFFSET	(512 * 1658)
+#define CONFIG_ENV_OFFSET	(512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_OFFSET	(2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define CONFIG_ENV_IS_IN_REMOTE
@@ -129,7 +189,16 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Config the L3 Cache as L3 SRAM
  */
-#define CONFIG_SYS_INIT_L3_ADDR	 CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		(512 << 10)
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(50 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
 
 #define CONFIG_SYS_DCSRBAR	0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull
@@ -139,7 +208,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #define CONFIG_SYS_EEPROM_BUS_NUM	0
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
 
 /*
  * DDR Setup
@@ -301,7 +370,12 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_SYS_MONITOR_BASE	 CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
+#endif
+
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
 #define CONFIG_MISC_INIT_R
 #define CONFIG_HWCONFIG
@@ -320,7 +394,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 						GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 /*
@@ -510,23 +584,26 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR		0x110000
 #define CONFIG_CORTINA_FW_ADDR		0x120000
 
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
-#define CONFIG_CORTINA_FW_ADDR		(512 * 1808)
+#define CONFIG_SYS_CORTINA_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR		(512 * 0x820)
+#define CONFIG_CORTINA_FW_ADDR		(512 * 0x8a0)
 
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#define CONFIG_CORTINA_FW_ADDR		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_CORTINA_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR		(3 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_CORTINA_FW_ADDR		(4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -536,11 +613,13 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_CORTINA_FW_IN_REMOTE
+#define CONFIG_SYS_FMAN_FW_ADDR		0xFFE00000
 #define CONFIG_CORTINA_FW_ADDR		0xFFE10000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
+#define CONFIG_SYS_CORTINA_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #define CONFIG_CORTINA_FW_ADDR		0xEFE00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
@@ -616,6 +695,22 @@ unsigned long get_board_ddr_clk(void);
 #endif
 
 /*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+			"spi0=spife110000.1"
+#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+			"128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
+			"5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \
+			"1m(uboot),5m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
  * Environment
  */
 
diff --git a/include/configs/T4240EMU.h b/include/configs/T4240EMU.h
index c81c4577e3..ad5a9a6f0c 100644
--- a/include/configs/T4240EMU.h
+++ b/include/configs/T4240EMU.h
@@ -98,7 +98,7 @@
 #define CONFIG_SYS_INTERLAKEN
 
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h
index 56e1293720..e4eb30fbeb 100644
--- a/include/configs/T4240QDS.h
+++ b/include/configs/T4240QDS.h
@@ -19,11 +19,64 @@
 #define CONFIG_ICS307_REFCLK_HZ		25000000  /* ICS307 ref clk freq */
 
 #ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t4qds/t4_pbi.cfg
 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t4qds/t4_rcw.cfg
+#if !defined(CONFIG_NAND) && !defined(CONFIG_SDCARD)
+#define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
+#else
+#define CONFIG_SPL
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW                 /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE		0x00201000
+#define CONFIG_SPL_TEXT_BASE		0xFFFD8000
+#define CONFIG_SPL_PAD_TO		0x40000
+#define CONFIG_SPL_MAX_SIZE		0x28000
+#define RESET_VECTOR_OFFSET		0x27FFC
+#define BOOT_PAGE_OFFSET		0x27000
+
+#ifdef	CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START	0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(256 << 10)
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef	CONFIG_SDCARD
+#define	CONFIG_RESET_VECTOR_ADDRESS	0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE	(768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST	0x00200000
+#define CONFIG_SYS_MMC_U_BOOT_START	0x00200000
+#define CONFIG_SYS_MMC_U_BOOT_OFFS	(260 << 10)
+#ifndef CONFIG_SPL_BUILD
+#define	CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SYS_LDSCRIPT	"arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
 #endif
+#endif /* CONFIG_RAMBOOT_PBL */
 
 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 /* Set 1M boot space */
@@ -64,12 +117,12 @@
 #define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_SYS_MMC_ENV_DEV          0
 #define CONFIG_ENV_SIZE			0x2000
-#define CONFIG_ENV_OFFSET		(512 * 1658)
+#define CONFIG_ENV_OFFSET		(512 * 0x800)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(10 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 #define CONFIG_ENV_IS_IN_REMOTE
 #define CONFIG_ENV_ADDR		0xffe20000
@@ -244,8 +297,16 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR1_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
 #define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
 #define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
@@ -261,6 +322,14 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
 #define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
 #define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 #define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
 #define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
@@ -270,14 +339,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
 #define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
 #endif
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
 
 #if defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_SYS_RAMBOOT
@@ -375,18 +436,18 @@ unsigned long get_board_ddr_clk(void);
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 0x820)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(11 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -396,10 +457,10 @@ unsigned long get_board_ddr_clk(void);
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 036c609582..762f6d2e4b 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -301,6 +301,7 @@
 #endif
 
 /* USB Device Firmware Update support */
+#ifndef CONFIG_SPL_BUILD
 #define CONFIG_DFU_FUNCTION
 #define CONFIG_DFU_MMC
 #define CONFIG_CMD_DFU
@@ -309,10 +310,10 @@
 	"boot part 0 1;" \
 	"rootfs part 0 2;" \
 	"MLO fat 0 1;" \
-	"MLO.raw mmc 100 100;" \
-	"u-boot.img.raw mmc 300 400;" \
-	"spl-os-args.raw mmc 80 80;" \
-	"spl-os-image.raw mmc 900 2000;" \
+	"MLO.raw mmc 0x100 0x100;" \
+	"u-boot.img.raw mmc 0x300 0x400;" \
+	"spl-os-args.raw mmc 0x80 0x80;" \
+	"spl-os-image.raw mmc 0x900 0x2000;" \
 	"spl-os-args fat 0 1;" \
 	"spl-os-image fat 0 1;" \
 	"u-boot.img fat 0 1;" \
@@ -343,6 +344,7 @@
 	DFU_ALT_INFO_MMC \
 	DFU_ALT_INFO_RAM \
 	DFU_ALT_INFO_NAND
+#endif
 
 /*
  * Default to using SPI for environment, etc.
diff --git a/include/configs/axs101.h b/include/configs/axs101.h
index f6b569abfd..c22d6d0c75 100644
--- a/include/configs/axs101.h
+++ b/include/configs/axs101.h
@@ -16,7 +16,7 @@
 #define CONFIG_SYS_CLK_FREQ		750000000
 #define CONFIG_SYS_TIMER_RATE		CONFIG_SYS_CLK_FREQ
 
-/* dwgmac doesn't work with D$ enabled now */
+/* NAND controller DMA doesn't work correctly with D$ enabled */
 #define CONFIG_SYS_DCACHE_OFF
 
 /*
@@ -40,7 +40,7 @@
 
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_SYS_SDRAM_SIZE		0x10000000	/* 256 Mb */
+#define CONFIG_SYS_SDRAM_SIZE		0x20000000	/* 512 Mb */
 
 #define CONFIG_SYS_INIT_SP_ADDR		\
 	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
@@ -103,7 +103,7 @@
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	32
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	64
 
 /*
  * SD/MMC configuration
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 1e4bfc49fc..db6b9be73c 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -310,7 +310,7 @@
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
 
 /* Serial Port - controlled on board with jumper J8
@@ -509,7 +509,7 @@
  * env, so we got 0x110000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x110000
 #elif defined(CONFIG_SDCARD)
 /*
  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
@@ -517,10 +517,10 @@
  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
+#define CONFIG_SYS_FMAN_FW_ADDR	(512 * 1680)
 #elif defined(CONFIG_NAND)
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 /*
  * Slave has no ucode locally, it can fetch this from remote. When implementing
@@ -530,10 +530,10 @@
  * master LAW->the ucode address in master's memory space.
  */
 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#define CONFIG_SYS_FMAN_FW_ADDR	0xFFE00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEFF00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/exynos4-dt.h b/include/configs/exynos4-dt.h
index 2040bf7784..cbd2d204cf 100644
--- a/include/configs/exynos4-dt.h
+++ b/include/configs/exynos4-dt.h
@@ -127,7 +127,6 @@
 #define CONFIG_USB_GADGET_S3C_UDC_OTG
 #define CONFIG_USB_GADGET_DUALSPEED
 #define CONFIG_USB_GADGET_VBUS_DRAW	2
-#define CONFIG_USB_CABLE_CHECK
 
 #define CONFIG_CMD_USB_MASS_STORAGE
 #define CONFIG_USB_GADGET_MASS_STORAGE
diff --git a/include/configs/gr_cpci_ax2000.h b/include/configs/gr_cpci_ax2000.h
index 2437b4b613..854807d486 100644
--- a/include/configs/gr_cpci_ax2000.h
+++ b/include/configs/gr_cpci_ax2000.h
@@ -19,8 +19,6 @@
  * (easy to change)
  */
 
-#define CONFIG_LEON3		/* This is an LEON3 CPU */
-#define CONFIG_LEON		1	/* This is an LEON CPU */
 #define CONFIG_CPCI_AX2000	1	/* ... on GR-CPCI-AX2000 board */
 
 #define CONFIG_LEON_RAM_SRAM 1
diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
index 2cd6eaedcc..ed2dd2a847 100644
--- a/include/configs/gr_ep2s60.h
+++ b/include/configs/gr_ep2s60.h
@@ -20,8 +20,6 @@
  * (easy to change)
  */
 
-#define CONFIG_LEON3		/* This is an LEON3 CPU */
-#define CONFIG_LEON		1	/* This is an LEON CPU */
 /* Altera NIOS Development board, Stratix II board */
 #define CONFIG_GR_EP2S60	1
 
diff --git a/include/configs/gr_xc3s_1500.h b/include/configs/gr_xc3s_1500.h
index 39036cdf7e..e3cbb6f596 100644
--- a/include/configs/gr_xc3s_1500.h
+++ b/include/configs/gr_xc3s_1500.h
@@ -18,8 +18,6 @@
  * (easy to change)
  */
 
-#define CONFIG_LEON3		/* This is an LEON3 CPU */
-#define CONFIG_LEON		1	/* This is an LEON CPU */
 #define CONFIG_GRXC3S1500	1	/* ... on GR-XC3S-1500 board */
 
 /* CPU / AMBA BUS configuration */
diff --git a/include/configs/grsim.h b/include/configs/grsim.h
index 2d977ceeb6..556c749f92 100644
--- a/include/configs/grsim.h
+++ b/include/configs/grsim.h
@@ -24,8 +24,6 @@
  *
  */
 
-#define CONFIG_LEON3			/* This is an LEON3 CPU */
-#define CONFIG_LEON		1	/* This is an LEON CPU */
 #define CONFIG_GRSIM		0	/* ... not running on GRSIM */
 #define CONFIG_TSIM		1	/* ... running on TSIM */
 
diff --git a/include/configs/grsim_leon2.h b/include/configs/grsim_leon2.h
index 36ebaf7ff7..8be98983c9 100644
--- a/include/configs/grsim_leon2.h
+++ b/include/configs/grsim_leon2.h
@@ -23,8 +23,6 @@
  *
  */
 
-#define CONFIG_LEON2		/* This is an LEON2 CPU */
-#define CONFIG_LEON		1	/* This is an LEON CPU */
 #define CONFIG_GRSIM		0	/* ... not running on GRSIM */
 #define CONFIG_TSIM		1	/* ... running on TSIM */
 
diff --git a/include/configs/highbank.h b/include/configs/highbank.h
index 7dbee3cdb9..a6202cfab4 100644
--- a/include/configs/highbank.h
+++ b/include/configs/highbank.h
@@ -7,15 +7,15 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <config_distro_defaults.h>
+
 #define CONFIG_SYS_DCACHE_OFF
 #define CONFIG_SYS_THUMB_BUILD
 
 #define CONFIG_SYS_NO_FLASH
 
-#define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_FIT
-#define CONFIG_SUPPORT_RAW_INITRD
 #define CONFIG_SYS_BOOTMAPSZ		(16 << 20)
 
 #define CONFIG_SYS_TIMER_RATE		(150000000/256)
@@ -48,35 +48,18 @@
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 					CONFIG_SYS_SCSI_MAX_LUN)
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-
 #define CONFIG_CALXEDA_XGMAC
 
-/* PXE support */
-#define CONFIG_BOOTP_PXE
-#define CONFIG_BOOTP_PXE_CLIENTARCH	0x100
-#define CONFIG_BOOTP_VCI_STRING		"U-boot.armv7.highbank"
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_LOADS
 #define CONFIG_CMD_SCSI
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PXE
-#define CONFIG_MENU
 
-#define CONFIG_BOOTDELAY		2
 #define CONFIG_BOOT_RETRY_TIME		-1
 #define CONFIG_RESET_TO_RETRY
 #define CONFIG_AUTOBOOT_KEYED
@@ -85,14 +68,9 @@
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_LONGHELP		/* undef to save memory		 */
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 #define CONFIG_SYS_MAXARGS		16	/* max number of cmd args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_PROMPT		"Highbank #"
-#define CONFIG_SYS_HUSH_PARSER
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					 sizeof(CONFIG_SYS_PROMPT)+16)
diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
new file mode 100644
index 0000000000..613f7e1a2e
--- /dev/null
+++ b/include/configs/ids8313.h
@@ -0,0 +1,587 @@
+/*
+ * (C) Copyright 2013
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * Copyright (c) 2011 IDS GmbH, Germany
+ * Sergej Stepanov <ste@ids.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC831x
+#define CONFIG_MPC8313
+#define CONFIG_IDS8313
+
+#define CONFIG_FSL_ELBC
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT	\
+	"\nEnter password - autoboot in %d seconds...\n", CONFIG_BOOTDELAY
+#define CONFIG_AUTOBOOT_DELAY_STR	"ids"
+#define CONFIG_BOOT_RETRY_TIME		900
+#define CONFIG_BOOT_RETRY_MIN		30
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_RESET_TO_RETRY
+
+#define CONFIG_83XX_CLKIN		66000000	/* in Hz */
+#define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR		0xF0000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.000MHz, then
+ * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
+ */
+#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
+			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
+			     HRCWL_CSB_TO_CLKIN_2X1 |\
+			     HRCWL_CORE_TO_CSB_2X1)
+
+#define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
+				 HRCWH_CORE_ENABLE |\
+				 HRCWH_FROM_0XFFF00100 |\
+				 HRCWH_BOOTSEQ_DISABLE |\
+				 HRCWH_SW_WATCHDOG_DISABLE |\
+				 HRCWH_ROM_LOC_LOCAL_8BIT |\
+				 HRCWH_RL_EXT_LEGACY |\
+				 HRCWH_TSEC1M_IN_MII |\
+				 HRCWH_TSEC2M_IN_MII |\
+				 HRCWH_BIG_ENDIAN)
+
+#define CONFIG_SYS_SICRH	0x00000000
+#define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
+
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
+				 HID0_ENABLE_INSTRUCTION_CACHE |\
+				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
+
+#define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
+
+/*
+ * Definitions for initial stack pointer and data area (in DCACHE )
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
+					 - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
+					 (0xFF << LBCR_BMT_SHIFT) |\
+					 0xF)
+
+#define CONFIG_SYS_LBC_MRTPR		0x20000000
+
+/*
+ * Internal Definitions
+ */
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters,
+ * as this board has not the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE		256		/* MB */
+#define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
+					 0x00010000 |\
+					 CSCONFIG_ROW_BIT_13 |\
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
+					 CSCONFIG_BANK_BIT_3)
+
+#define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
+#define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
+				(3 << TIMING_CFG0_WRT_SHIFT) |\
+				(3 << TIMING_CFG0_RRT_SHIFT) |\
+				(3 << TIMING_CFG0_WWT_SHIFT) |\
+				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
+				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
+				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
+				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
+				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
+				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
+				(4 << TIMING_CFG1_REFREC_SHIFT) |\
+				(4 << TIMING_CFG1_WRREC_SHIFT) |\
+				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
+				(2 << TIMING_CFG1_WRTORD_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
+				(5 << TIMING_CFG2_CPO_SHIFT) |\
+				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
+				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
+				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
+				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
+				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
+
+#define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
+				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+
+#define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
+					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
+					 SDRAM_CFG_DBW_32 |\
+					 SDRAM_CFG_SDRAM_TYPE_DDR2)
+
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+#define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
+					 (0x0242 << SDRAM_MODE_SD_SHIFT))
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
+					 DDRCDR_PZ_NOMZ |\
+					 DDRCDR_NZ_NOMZ |\
+					 DDRCDR_ODT |\
+					 DDRCDR_M_ODR |\
+					 DDRCDR_Q_DRN)
+
+/*
+ * on-board devices
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+#define CONFIG_TSEC_ENET
+#define CONFIG_NET_MULTI
+#define CONFIG_HARD_SPI
+#define CONFIG_HARD_I2C
+
+/*
+ * NOR FLASH setup
+ */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
+#define CONFIG_FLASH_SHOW_PROGRESS	50
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_SYS_FLASH_BASE		0xFF800000
+#define CONFIG_SYS_FLASH_SIZE		8
+#define CONFIG_SYS_FLASH_PROTECTION
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
+
+#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+					 OR_GPCM_SCY_10 |\
+					 OR_GPCM_EHTR |\
+					 OR_GPCM_TRLX |\
+					 OR_GPCM_CSNT |\
+					 OR_GPCM_EAD)
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	128
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500
+
+/*
+ * NAND FLASH setup
+ */
+#define CONFIG_SYS_NAND_BASE		0xE1000000
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_MAX_CHIPS	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
+#define NAND_CACHE_PAGES		64
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
+
+#define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
+				 (2<<BR_DECC_SHIFT) |\
+				 BR_PS_8 |\
+				 BR_MS_FCM |\
+				 BR_V)
+
+#define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
+				 OR_FCM_PGS |\
+				 OR_FCM_CSCT |\
+				 OR_FCM_CST |\
+				 OR_FCM_CHT |\
+				 OR_FCM_SCY_4 |\
+				 OR_FCM_TRLX |\
+				 OR_FCM_EHTR |\
+				 OR_FCM_RST)
+
+/*
+ * MRAM setup
+ */
+#define CONFIG_SYS_MRAM_BASE		0xE2000000
+#define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
+
+/*
+ * CPLD setup
+ */
+#define CONFIG_SYS_CPLD_BASE		0xE3000000
+#define CONFIG_SYS_CPLD_SIZE		0x8000
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
+
+/*
+ * HW-Watchdog
+ */
+#define CONFIG_WATCHDOG		1
+#define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
+
+/*
+ * I2C setup
+ */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
+#define CONFIG_RTC_PCF8563
+#define CONFIG_SYS_I2C_RTC_ADDR	0x51
+
+/*
+ * SPI setup
+ */
+#ifdef CONFIG_HARD_SPI
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR		0x00000001
+#define CONFIG_SYS_GPIO1_DAT		0x00000001
+#endif
+
+/*
+ * Ethernet setup
+ */
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME		"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR			0x1
+#define TSEC1_FLAGS			TSEC_GIGABIT
+#define TSEC1_PHYIDX			0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME		"TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET	0x25000
+#define TSEC2_PHY_ADDR			0x3
+#define TSEC2_FLAGS			TSEC_GIGABIT
+#define TSEC2_PHYIDX			0
+#endif
+#define CONFIG_ETHPRIME		"TSEC1"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+#define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
+
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_SYS_SCCR_USBDRCM	3
+
+/*
+ * BAT's
+ */
+#define CONFIG_HIGH_BATS
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
+					 BATL_PP_10)
+#define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
+					 BATU_BL_256M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
+
+/* Initial RAM @ 0xFD000000 */
+#define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
+					 BATU_BL_256K |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
+
+/* FLASH @ 0xFF800000 */
+#define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
+					 BATU_BL_8M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
+					 BATL_PP_10 |\
+					 BATL_CACHEINHIBIT |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
+
+#define CONFIG_SYS_IBAT3L		(0)
+#define CONFIG_SYS_IBAT3U		(0)
+#define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
+
+#define CONFIG_SYS_IBAT4L		(0)
+#define CONFIG_SYS_IBAT4U		(0)
+#define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
+
+/* IMMRBAR @ 0xF0000000 */
+#define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
+					 BATL_PP_10 |\
+					 BATL_CACHEINHIBIT |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
+					 BATU_BL_128M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
+
+/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
+#define CONFIG_SYS_IBAT6L		(0xE0000000 |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U		(0xE0000000 |\
+					 BATU_BL_256M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
+
+#define CONFIG_SYS_IBAT7L		(0)
+#define CONFIG_SYS_IBAT7U		(0)
+#define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
+
+/*
+ * U-Boot environment setup
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CMD_EDITENV
+#define CONFIG_CMD_JFFS2
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
+				+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE		0x20000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+
+#define CONFIG_NETDEV			eth1
+#define CONFIG_HOSTNAME		ids8313
+#define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
+#define CONFIG_BOOTFILE		"ids8313/uImage"
+#define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
+#define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
+#define CONFIG_LOADADDR		0x400000
+#define CONFIG_CMD_ENV_FLAGS
+#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SYS_HZ			1000
+
+/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT		"=> "
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
+					 + sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x00C00000
+
+#define CONFIG_SYS_LOAD_ADDR		0x100000
+#define CONFIG_MII
+#define CONFIG_LOADS_ECHO
+#define CONFIG_TIMESTAMP
+#define CONFIG_PREBOOT			"echo;" \
+					"echo Type \\\"run nfsboot\\\" " \
+					"to mount root filesystem over NFS;echo"
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND		"run boot_cramfs"
+#undef	CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_DEV		"0"
+
+/* mtdparts command line support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_MTD_DEVICE
+#define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
+#define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
+					"768k(BOOT-BIN)," \
+					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
+					"e1000000.flash:-(ubi)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
+	"ethprime=TSEC1\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
+		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" +${filesize}; "					\
+		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +${filesize}; "					\
+		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" ${filesize}; "					\
+		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +${filesize}; "					\
+		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" ${filesize}\0"					\
+	"console=ttyS0\0"						\
+	"fdtaddr=0x780000\0"						\
+	"kernel_addr=ff800000\0"					\
+	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
+	"setbootargs=setenv bootargs "					\
+		"root=${rootdev} rw console=${console},"		\
+			"${baudrate} ${othbootargs}\0"			\
+	"setipargs=setenv bootargs root=${rootdev} rw "			\
+			"nfsroot=${serverip}:${rootpath} "		\
+			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
+			"${netmask}:${hostname}:${netdev}:off "		\
+			"console=${console},${baudrate} ${othbootargs}\0" \
+	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
+	"mtdids=" MTDIDS_DEFAULT "\0"					\
+	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
+	"\0"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setipargs;run addmtd;"					\
+	"tftp ${loadaddr} ${bootfile};"				\
+	"tftp ${fdtaddr} ${fdtfile};"					\
+	"fdt addr ${fdtaddr};"						\
+	"bootm ${loadaddr} - ${fdtaddr}"
+
+/* UBI Support */
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_PARTITIONS
+
+/* bootcount support */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_I2C
+#define CONFIG_BOOTCOUNT_ALEN	1
+#define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
+
+#define CONFIG_VERSION_VARIABLE
+
+#define CONFIG_FIT
+#define CONFIG_FIT_SIGNATURE
+#define CONFIG_CMD_FDT
+#define CONFIG_CMD_HASH
+#define CONFIG_RSA
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+#define CONFIG_OF_CONTROL
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/incaip.h b/include/configs/incaip.h
deleted file mode 100644
index e11d1843b9..0000000000
--- a/include/configs/incaip.h
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * This file contains the configuration parameters for the INCA-IP board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_INCA_IP		1	/* on a INCA-IP Board	*/
-
-#define CONFIG_XWAY_SWAP_BYTES
-
-/*
- * Clock for the MIPS core (MHz)
- * allowed values: 100000000, 133000000, and 150000000 (default)
- */
-#ifndef CONFIG_CPU_CLOCK_RATE
-#define CONFIG_CPU_CLOCK_RATE	150000000
-#endif
-
-#define CONFIG_SYS_XWAY_EBU_BOOTCFG	0x40C4	/* CMULT = 8 */
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_BAUDRATE		115200
-
-#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off\0"				\
-	"addmisc=setenv bootargs ${bootargs} "				\
-		"console=ttyS0,${baudrate} "				\
-		"ethaddr=${ethaddr} "					\
-		"panic=1\0"						\
-	"flash_nfs=run nfsargs addip addmisc;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addmisc;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 80500000 ${bootfile};"				\
-		"run nfsargs addip addmisc;bootm\0"			\
-	"rootpath=/opt/eldk/mips_4KC\0"					\
-	"bootfile=/tftpboot/INCA/uImage\0"				\
-	"kernel_addr=B0040000\0"					\
-	"ramdisk_addr=B0100000\0"					\
-	"u-boot=/tftpboot/INCA/u-boot.bin\0"				\
-	"load=tftp 80500000 ${u-boot}\0"				\
-	"update=protect off 1:0-2;era 1:0-2;"				\
-		"cp.b 80500000 B0000000 ${filesize}\0"			\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory      */
-#define	CONFIG_SYS_PROMPT		"INCA-IP # "	/* Monitor Command Prompt    */
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size   */
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)  /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args*/
-
-#define CONFIG_SYS_MALLOC_LEN		128*1024
-
-#define CONFIG_SYS_BOOTPARAMS_LEN	128*1024
-
-#define CONFIG_SYS_MIPS_TIMER_FREQ	(incaip_get_cpuclk() / 2)
-
-#define CONFIG_SYS_SDRAM_BASE		0x80000000
-
-#define	CONFIG_SYS_LOAD_ADDR		0x80100000	/* default load address	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x80100000
-#define CONFIG_SYS_MEMTEST_END		0x80800000
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	(128)	/* max number of sectors on one chip */
-
-#define PHYS_FLASH_1		0xb0000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2		0xb0800000 /* Flash Bank #2 */
-
-/* The following #defines are needed to get flash environment right */
-#define	CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)
-
-#define CONFIG_SYS_INIT_SP_OFFSET	0x400000
-
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(2 * CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-
-/* Address and size of Primary Environment Sector	*/
-#define CONFIG_ENV_ADDR		0xB0030000
-#define CONFIG_ENV_SIZE		0x10000
-
-#define CONFIG_FLASH_16BIT
-
-#define CONFIG_NR_DRAM_BANKS	1
-
-#define CONFIG_INCA_IP_SWITCH
-#define CONFIG_INCA_IP_SWITCH_AMDIX
-
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition, use all space on the device */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor1"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor0=INCA-IP Bank 0"
-#define MTDPARTS_DEFAULT	"mtdparts=INCA-IP Bank 0:192k(uboot)," \
-							"64k(env)," \
-							"768k(linux)," \
-							"1m@3m(rootfs)," \
-							"768k(linux2)," \
-							"3m@5m(rootfs2)"
-*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_DCACHE_SIZE		4096
-#define CONFIG_SYS_ICACHE_SIZE		4096
-#define CONFIG_SYS_CACHELINE_SIZE	16
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/km/km8309-common.h b/include/configs/km/km8309-common.h
index 29c6f60971..c8df23b534 100644
--- a/include/configs/km/km8309-common.h
+++ b/include/configs/km/km8309-common.h
@@ -27,7 +27,7 @@
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 /* at end of uboot partition, before env */
-#define CONFIG_SYS_QE_FMAN_FW_ADDR   0xF00B0000
+#define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
 
 /*
  * System IO Config
diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h
index 582978afe2..418e3d1298 100644
--- a/include/configs/km/kmp204x-common.h
+++ b/include/configs/km/kmp204x-common.h
@@ -350,7 +350,7 @@ int get_scl(void);
  * ucode is stored after env, so we got 0x120000.
  */
 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x120000
+#define CONFIG_SYS_FMAN_FW_ADDR	0x120000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
diff --git a/include/configs/lubbock.h b/include/configs/lubbock.h
deleted file mode 100644
index 4ffe165dec..0000000000
--- a/include/configs/lubbock.h
+++ /dev/null
@@ -1,236 +0,0 @@
-/*
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the LUBBOCK board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_CPU_PXA25X		1	/* This is an PXA250 CPU    */
-#define CONFIG_LUBBOCK		1	/* on an LUBBOCK Board	    */
-#define CONFIG_LCD		1
-#ifdef CONFIG_LCD
-#define CONFIG_PXA_LCD
-#define CONFIG_SHARP_LM8V31
-#endif
-#define CONFIG_MMC
-#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_DOS_PARTITION
-#define	CONFIG_SYS_TEXT_BASE	0x0
-
-/* we will never enable dcache, because we have to setup MMU first */
-#define CONFIG_SYS_DCACHE_OFF
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN	    (CONFIG_ENV_SIZE + 128*1024)
-
-/*
- * Hardware drivers
- */
-#define CONFIG_LAN91C96
-#define CONFIG_LAN91C96_BASE 0x0C000000
-
-/*
- * select serial console configuration
- */
-#define CONFIG_PXA_SERIAL
-#define CONFIG_FFUART	       1       /* we use FFUART on LUBBOCK */
-#define CONFIG_CONS_INDEX	3
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_BAUDRATE		115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_FAT
-
-
-#define CONFIG_BOOTDELAY	3
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5b
-#define CONFIG_NETMASK		255.255.0.0
-#define CONFIG_IPADDR		192.168.0.21
-#define CONFIG_SERVERIP		192.168.0.250
-#define CONFIG_BOOTCOMMAND	"bootm 80000"
-#define CONFIG_BOOTARGS		"root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_TIMESTAMP
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER		1
-
-#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT		"$ "		/* Monitor Command Prompt */
-#else
-#endif
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_DEVICE_NULLDEV	1
-
-#define CONFIG_SYS_MEMTEST_START	0xa0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DRAM_BASE + 0x8000) /* default load address */
-
-#define CONFIG_SYS_CPUSPEED		0x161		/* set core clock to 400/200/100 MHz */
-
-#ifdef CONFIG_MMC
-#define	CONFIG_GENERIC_MMC
-#define	CONFIG_PXA_MMC_GENERIC
-#define CONFIG_CMD_MMC
-#define CONFIG_SYS_MMC_BASE		0xF0000000
-#endif
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
-#define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE	0x04000000 /* 64 MB */
-#define PHYS_SDRAM_2		0xa4000000 /* SDRAM Bank #2 */
-#define PHYS_SDRAM_2_SIZE	0x00000000 /* 0 MB */
-#define PHYS_SDRAM_3		0xa8000000 /* SDRAM Bank #3 */
-#define PHYS_SDRAM_3_SIZE	0x00000000 /* 0 MB */
-#define PHYS_SDRAM_4		0xac000000 /* SDRAM Bank #4 */
-#define PHYS_SDRAM_4_SIZE	0x00000000 /* 0 MB */
-
-#define PHYS_FLASH_1		0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2		0x04000000 /* Flash Bank #2 */
-#define PHYS_FLASH_SIZE		0x02000000 /* 32 MB */
-#define PHYS_FLASH_BANK_SIZE	0x02000000 /* 32 MB Banks */
-#define PHYS_FLASH_SECT_SIZE	0x00040000 /* 256 KB sectors (x2) */
-
-#define CONFIG_SYS_DRAM_BASE		0xa0000000
-#define CONFIG_SYS_DRAM_SIZE		0x04000000
-
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
-#define	CONFIG_SYS_INIT_SP_ADDR		0xfffff800
-
-#define FPGA_REGS_BASE_PHYSICAL 0x08000000
-
-/*
- * GPIO settings
- */
-#define CONFIG_SYS_GPSR0_VAL		0x00008000
-#define CONFIG_SYS_GPSR1_VAL		0x00FC0382
-#define CONFIG_SYS_GPSR2_VAL		0x0001FFFF
-#define CONFIG_SYS_GPCR0_VAL		0x00000000
-#define CONFIG_SYS_GPCR1_VAL		0x00000000
-#define CONFIG_SYS_GPCR2_VAL		0x00000000
-#define CONFIG_SYS_GPDR0_VAL		0x0060A800
-#define CONFIG_SYS_GPDR1_VAL		0x00FF0382
-#define CONFIG_SYS_GPDR2_VAL		0x0001C000
-#define CONFIG_SYS_GAFR0_L_VAL		0x98400000
-#define CONFIG_SYS_GAFR0_U_VAL		0x00002950
-#define CONFIG_SYS_GAFR1_L_VAL		0x000A9558
-#define CONFIG_SYS_GAFR1_U_VAL		0x0005AAAA
-#define CONFIG_SYS_GAFR2_L_VAL		0xA0000000
-#define CONFIG_SYS_GAFR2_U_VAL		0x00000002
-
-#define CONFIG_SYS_PSSR_VAL		0x20
-
-#define	CONFIG_SYS_CCCR			CCCR_L27|CCCR_M2|CCCR_N10
-#define	CONFIG_SYS_CKEN			0x0
-
-/*
- * Memory settings
- */
-#define CONFIG_SYS_MSC0_VAL		0x23F223F2
-#define CONFIG_SYS_MSC1_VAL		0x3FF1A441
-#define CONFIG_SYS_MSC2_VAL		0x7FF97FF1
-#define CONFIG_SYS_MDCNFG_VAL		0x00001AC9
-#define CONFIG_SYS_MDREFR_VAL		0x00018018
-#define CONFIG_SYS_MDMRS_VAL		0x00000000
-
-#define	CONFIG_SYS_FLYCNFG_VAL		0x00000000
-#define	CONFIG_SYS_SXCNFG_VAL		0x00000000
-
-/*
- * PCMCIA and CF Interfaces
- */
-#define CONFIG_SYS_MECR_VAL		0x00000000
-#define CONFIG_SYS_MCMEM0_VAL		0x00010504
-#define CONFIG_SYS_MCMEM1_VAL		0x00010504
-#define CONFIG_SYS_MCATT0_VAL		0x00010504
-#define CONFIG_SYS_MCATT1_VAL		0x00010504
-#define CONFIG_SYS_MCIO0_VAL		0x00004715
-#define CONFIG_SYS_MCIO1_VAL		0x00004715
-
-#define _LED			0x08000010
-#define LED_BLANK		0x08000040
-
-/*
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128  /* max number of sectors on one chip    */
-
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	(25*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	(25*CONFIG_SYS_HZ) /* Timeout for Flash Write */
-
-/* NOTE: many default partitioning schemes assume the kernel starts at the
- * second sector, not an environment.  You have been warned!
- */
-#define	CONFIG_SYS_MONITOR_LEN		PHYS_FLASH_SECT_SIZE
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE)
-#define CONFIG_ENV_SECT_SIZE	PHYS_FLASH_SECT_SIZE
-#define CONFIG_ENV_SIZE		(PHYS_FLASH_SECT_SIZE / 16)
-
-
-/*
- * FPGA Offsets
- */
-#define WHOAMI_OFFSET		0x00
-#define HEXLED_OFFSET		0x10
-#define BLANKLED_OFFSET		0x40
-#define DISCRETELED_OFFSET	0x40
-#define CNFG_SWITCHES_OFFSET	0x50
-#define USER_SWITCHES_OFFSET	0x60
-#define MISC_WR_OFFSET		0x80
-#define MISC_RD_OFFSET		0x90
-#define INT_MASK_OFFSET		0xC0
-#define INT_CLEAR_OFFSET	0xD0
-#define GP_OFFSET		0x100
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/malta.h b/include/configs/malta.h
index cc574ed040..a29b86b4f6 100644
--- a/include/configs/malta.h
+++ b/include/configs/malta.h
@@ -14,6 +14,9 @@
  * System configuration
  */
 #define CONFIG_MALTA
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_DISPLAY_BOARDINFO
 
 #define CONFIG_MEMSIZE_IN_BYTES
 
diff --git a/include/configs/microblaze-generic.h b/include/configs/microblaze-generic.h
index 486787e147..06b7e94184 100644
--- a/include/configs/microblaze-generic.h
+++ b/include/configs/microblaze-generic.h
@@ -71,7 +71,7 @@
 
 /* ethernet */
 #undef CONFIG_SYS_ENET
-#if defined(XILINX_EMACLITE_BASEADDR)
+#if defined(XILINX_EMACLITE_BASEADDR) || defined(CONFIG_OF_CONTROL)
 # define CONFIG_XILINX_EMACLITE	1
 # define CONFIG_SYS_ENET
 #endif
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 07b61795bb..e745945ba7 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -508,7 +508,7 @@
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)/* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)/* Reserved for malloc */
 
 #define CONFIG_SYS_CPLD_BASE	0xffa00000
@@ -772,7 +772,7 @@
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FW_ADDR	0xefec0000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */
 
diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index c296a07599..911203d85c 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -202,7 +202,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024)/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)/* Reserved for malloc */
 
 #define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
@@ -348,7 +348,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xefec0000
+#define CONFIG_SYS_QE_FW_ADDR	0xefec0000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #endif /* CONFIG_QE */
 
diff --git a/include/configs/qemu-ppce500.h b/include/configs/qemu-ppce500.h
new file mode 100644
index 0000000000..10e014d33c
--- /dev/null
+++ b/include/configs/qemu-ppce500.h
@@ -0,0 +1,206 @@
+/*
+ * Copyright 2011-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * Corenet DS style board configuration file
+ */
+#ifndef __QEMU_PPCE500_H
+#define __QEMU_PPCE500_H
+
+#define CONFIG_CMD_REGINFO
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_QEMU_E500
+
+#undef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xf01000 /* 15 MB */
+
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+
+#define CONFIG_SYS_RAMBOOT
+
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#define CONFIG_PCI1		1	/* PCI controller 1 */
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/* Needed to fill the ccsrbar pointer */
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* Virtual address to CCSRBAR */
+#define CONFIG_SYS_CCSRBAR		0xe0000000
+/* Physical address should be a function call */
+#ifndef __ASSEMBLY__
+extern unsigned long long get_phys_ccsrbar_addr_early(void);
+#endif
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+
+/* Virtual address range for PCI region maps */
+#define CONFIG_SYS_PCI_MAP_START	0x80000000
+#define CONFIG_SYS_PCI_MAP_END		0xe8000000
+
+/* Virtual address to a temporary map if we need it (max 128MB) */
+#define CONFIG_SYS_TMPVIRT		0xe8000000
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_CHIP_SELECTS_PER_CTRL	0
+
+#define CONFIG_SYS_CLK_FREQ        33000000
+
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_SYS_BOOT_BLOCK		0x00000000	/* boot TLB */
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_ENV_IS_NOWHERE
+
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_INIT_RAM_ADDR		0x00100000
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0x0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0x00100000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+#define CONFIG_LBA48
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_SIZE		0x2000
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BAUDRATE	115200
+
+#define CONFIG_BOOTDELAY        1
+#define CONFIG_BOOTCOMMAND		\
+	"test -n \"$qemu_kernel_addr\" && bootm $qemu_kernel_addr - $fdt_addr_r\0"
+
+#endif	/* __QEMU_PPCE500_H */
diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h
deleted file mode 100644
index 06211380d4..0000000000
--- a/include/configs/rsdproto.h
+++ /dev/null
@@ -1,400 +0,0 @@
-/*
- * (C) Copyright 2000
- * Murray Jensen <Murray.Jensen@cmst.csiro.au>
- *
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the R&S Protocol Board board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_RSD_PROTO	1	/* on a R&S Protocol Board      */
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define	CONFIG_SYS_TEXT_BASE	0xff000000
-#define	CONFIG_SYS_LDSCRIPT	"board/rsdproto/u-boot.lds"
-
-#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#undef	CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#define	CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef	CONFIG_CONS_NONE		/* define if console on neither */
-#define CONFIG_CONS_INDEX	1	/* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ethernet on SCC	*/
-#define	CONFIG_ETHER_ON_FCC		/* define if ethernet on FCC	*/
-#undef	CONFIG_ETHER_NONE		/* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX	2	/* which SCC/FCC channel for ethernet */
-
-#if (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	(0)
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
-
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* enable I2C */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x30
-
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#define CONFIG_8260_CLKIN	50000000	/* in Hz */
-
-#define CONFIG_BAUDRATE		115200
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_KGDB
-
-
-/* Define this if you want to boot from 0x00000100. If you don't define
- * this, you will need to program the bootloader to 0xfff00000, and
- * get the hardware reset config words at 0xfe000000. The simplest
- * way to do that is to program the bootloader at both addresses.
- * It is suggested that you just let U-Boot live at 0x00000000.
- */
-#define CONFIG_SYS_RSD_BOOT_LOW 1
-
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_BOOTARGS		"devfs=mount root=ramfs"
-#define CONFIG_ETHADDR		08:00:3e:26:0a:5a
-#define CONFIG_NETMASK          255.255.0.0
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP				/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x01c00000	/* 4 ... 28 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define PHYS_SDRAM_60X		0x00000000 /* SDRAM (60x Bus) */
-#define PHYS_SDRAM_60X_SIZE	0x08000000 /* 128 MB */
-
-#define PHYS_SDRAM_LOCAL	0x40000000 /* SDRAM (Local Bus) */
-#define PHYS_SDRAM_LOCAL_SIZE	0x04000000 /* 64 MB */
-
-#define PHYS_DPRAM_PCI		0xE8000000 /* DPRAM PPC/PCI */
-#define PHYS_DPRAM_PCI_SIZE	0x00020000 /* 128 KB */
-
-/*#define PHYS_DPRAM_PCI_SEM	0x04020000 / * DPRAM PPC/PCI Semaphore */
-/*#define PHYS_DPRAM_PCI_SEM_SIZE	0x00000001 / * 1 Byte */
-
-#define PHYS_DPRAM_SHARC	0xE8100000 /* DPRAM PPC/Sharc */
-#define PHYS_DPRAM_SHARC_SIZE	0x00040000 /* 256 KB */
-
-/*#define PHYS_DPRAM_SHARC_SEM	0x04140000 / * DPRAM PPC/Sharc Semaphore */
-/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */
-
-#define PHYS_VIRTEX_REGISTER    0xE8300000 /* FPGA implemented register */
-#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100
-
-#define PHYS_USB		0x04200000 /* USB Controller (60x Bus) */
-#define PHYS_USB_SIZE		0x00000002 /* 2 Bytes */
-
-#define PHYS_IMMR		0xF0000000 /* Internal Memory Mapped Reg. */
-
-#define PHYS_FLASH		0xFF000000 /* Flash (60x Bus) */
-#define PHYS_FLASH_SIZE		0x01000000 /* 16 MB */
-
-#define CONFIG_SYS_IMMR		PHYS_IMMR
-
-/*-----------------------------------------------------------------------
- * Reset Address
- *
- * In order to reset the CPU, U-Boot jumps to a special address which
- * causes a machine check exception. The default address for this is
- * CONFIG_SYS_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when
- * testing the monitor in RAM using a JTAG debugger.
- *
- * Just set CONFIG_SYS_RESET_ADDRESS to an address that you know is sure to
- * cause a bus error on your hardware.
- */
-#define CONFIG_SYS_RESET_ADDRESS	0x20000000
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-
-#if defined(CONFIG_SYS_RSD_BOOT_LOW)
-#  define  CONFIG_SYS_RSD_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
-#else
-#  define  CONFIG_SYS_RSD_HRCW_BOOT_FLAGS  (0)
-#endif /* defined(CONFIG_SYS_RSD_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_RSD_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
-			    ((CONFIG_SYS_IMMR & 0x01000000) >> 7)  |\
-			    ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER	(HRCW_L2CPC10 | \
-			 HRCW_DPPC11 | \
-			 CONFIG_SYS_RSD_HRCW_IMMR |\
-			 HRCW_MMR00 | \
-			 HRCW_APPC10 | \
-			 HRCW_CS10PC00 | \
-			 HRCW_MODCK_H0000 |\
-			 CONFIG_SYS_RSD_HRCW_BOOT_FLAGS)
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1	0
-#define CONFIG_SYS_HRCW_SLAVE2	0
-#define CONFIG_SYS_HRCW_SLAVE3	0
-#define CONFIG_SYS_HRCW_SLAVE4	0
-#define CONFIG_SYS_HRCW_SLAVE5	0
-#define CONFIG_SYS_HRCW_SLAVE6	0
-#define CONFIG_SYS_HRCW_SLAVE7	0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependend.
- */
-#define	CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_60X
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH
-/*#define	CONFIG_SYS_MONITOR_BASE	0x200000 */
-#define	CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMBOOT
-#endif
-#define	CONFIG_SYS_MONITOR_LEN		(160 << 10)	/* Reserve 160 kB for Monitor	*/
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	63	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	12000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	3000	/* Timeout for Flash Write (in ms)	*/
-
-/* turn off NVRAM env feature */
-#undef CONFIG_NVRAM_ENV
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR	(PHYS_FLASH + 0x28000)	/* Addr of Environment Sector	*/
-#define CONFIG_ENV_SECT_SIZE	0x8000	/* Total Size of Environment Sector	*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers			 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL	(HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP)
-#define CONFIG_SYS_HID2	0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR		0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration					 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR		0x100c0000
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \
-					 SIUMCR_CS10PC01 | SIUMCR_BCTLC01)
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \
-			 SYPCR_SWRI | SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control			 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC	(TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control					 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR	0x00000000
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration				13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR	0
-
-/*
- * Init Memory Controller:
- */
-
-#define CONFIG_SYS_PSDMR	0x494D2452
-#define CONFIG_SYS_LSDMR	0x49492552
-
-/* Flash */
-#define CONFIG_SYS_BR0_PRELIM	(PHYS_FLASH | BRx_V)
-#define CONFIG_SYS_OR0_PRELIM	(P2SZ_TO_AM(PHYS_FLASH_SIZE) | \
-			 ORxG_BCTLD | \
-			 ORxG_SCY_5_CLK)
-
-/* DPRAM to the PCI BUS on the protocol board */
-#define CONFIG_SYS_BR1_PRELIM	(PHYS_DPRAM_PCI | BRx_V)
-#define CONFIG_SYS_OR1_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \
-			 ORxG_ACS_DIV4)
-
-/* 60x Bus SDRAM */
-#define CONFIG_SYS_BR2_PRELIM	(PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V)
-#define CONFIG_SYS_OR2_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \
-			 ORxS_BPD_4 | \
-			 ORxS_ROWST_PBI1_A2 | \
-			 ORxS_NUMR_13 | \
-			 ORxS_IBID)
-
-/* Virtex-FPGA - Register */
-#define CONFIG_SYS_BR3_PRELIM  (PHYS_VIRTEX_REGISTER | BRx_V)
-#define CONFIG_SYS_OR3_PRELIM  (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \
-			 ORxG_SCY_1_CLK | \
-			 ORxG_ACS_DIV2 | \
-			 ORxG_CSNT )
-
-/* local bus SDRAM */
-#define CONFIG_SYS_BR4_PRELIM	(PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V)
-#define CONFIG_SYS_OR4_PRELIM	(ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \
-			 ORxS_BPD_4 | \
-			 ORxS_ROWST_PBI1_A4 | \
-			 ORxS_NUMR_13)
-
-/* DPRAM to the Sharc-Bus on the protocol board */
-#define CONFIG_SYS_BR5_PRELIM	(PHYS_DPRAM_SHARC | BRx_V)
-#define CONFIG_SYS_OR5_PRELIM	(P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \
-			 ORxG_ACS_DIV4)
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h
index bd324ba2fa..36bc5294ef 100644
--- a/include/configs/t4qds.h
+++ b/include/configs/t4qds.h
@@ -68,7 +68,16 @@
 /*
  *  Config the L3 Cache as L3 SRAM
  */
-#define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+#define CONFIG_SYS_L3_SIZE		(512 << 10)
+#define CONFIG_SPL_GD_ADDR		(CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR			(CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR	(CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE	(50 << 10)
+#define CONFIG_SPL_RELOC_STACK		(CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE	(22 << 10)
 
 #define CONFIG_SYS_DCSRBAR		0xf0000000
 #define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
@@ -96,7 +105,11 @@
 #define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 
 
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
 
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
 #define CONFIG_MISC_INIT_R
@@ -119,7 +132,7 @@
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
 
 /* Serial Port - controlled on board with jumper J8
diff --git a/include/configs/trats.h b/include/configs/trats.h
index 5d8bd60583..c4afecf3da 100644
--- a/include/configs/trats.h
+++ b/include/configs/trats.h
@@ -101,7 +101,7 @@
 	"name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \
 
 #define CONFIG_DFU_ALT \
-	"u-boot mmc 80 400;" \
+	"u-boot raw 0x80 0x400;" \
 	"uImage ext4 0 2;" \
 	"modem.bin ext4 0 2;" \
 	"exynos4210-trats.dtb ext4 0 2;" \
@@ -112,7 +112,7 @@
 	""PARTS_ROOT" part 0 5;" \
 	""PARTS_DATA" part 0 6;" \
 	""PARTS_UMS" part 0 7;" \
-	"params.bin mmc 0x38 0x8\0"
+	"params.bin raw 0x38 0x8\0"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"bootk=" \
diff --git a/include/configs/trats2.h b/include/configs/trats2.h
index 53d449c291..14def7d16e 100644
--- a/include/configs/trats2.h
+++ b/include/configs/trats2.h
@@ -91,7 +91,7 @@
 	"name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \
 
 #define CONFIG_DFU_ALT \
-	"u-boot mmc 80 800;" \
+	"u-boot raw 0x80 0x800;" \
 	"uImage ext4 0 2;" \
 	"modem.bin ext4 0 2;" \
 	"exynos4412-trats2.dtb ext4 0 2;" \
@@ -102,7 +102,7 @@
 	""PARTS_ROOT" part 0 5;" \
 	""PARTS_DATA" part 0 6;" \
 	""PARTS_UMS" part 0 7;" \
-	"params.bin mmc 0x38 0x8\0"
+	"params.bin raw 0x38 0x8\0"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"bootk=" \
diff --git a/include/ddr_spd.h b/include/ddr_spd.h
index 15a3e8d351..cf2aac6ae4 100644
--- a/include/ddr_spd.h
+++ b/include/ddr_spd.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008 Freescale Semiconductor, Inc.
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -290,11 +290,220 @@ typedef struct ddr3_spd_eeprom_s {
 
 } ddr3_spd_eeprom_t;
 
+/* From JEEC Standard No. 21-C release 23A */
+struct ddr4_spd_eeprom_s {
+	/* General Section: Bytes 0-127 */
+	uint8_t info_size_crc;		/*  0 # bytes */
+	uint8_t spd_rev;		/*  1 Total # bytes of SPD */
+	uint8_t mem_type;		/*  2 Key Byte / mem type */
+	uint8_t module_type;		/*  3 Key Byte / Module Type */
+	uint8_t density_banks;		/*  4 Density and Banks	*/
+	uint8_t addressing;		/*  5 Addressing */
+	uint8_t package_type;		/*  6 Package type */
+	uint8_t opt_feature;		/*  7 Optional features */
+	uint8_t thermal_ref;		/*  8 Thermal and refresh */
+	uint8_t oth_opt_features;	/*  9 Other optional features */
+	uint8_t res_10;			/* 10 Reserved */
+	uint8_t module_vdd;		/* 11 Module nominal voltage */
+	uint8_t organization;		/* 12 Module Organization */
+	uint8_t bus_width;		/* 13 Module Memory Bus Width */
+	uint8_t therm_sensor;		/* 14 Module Thermal Sensor */
+	uint8_t ext_type;		/* 15 Extended module type */
+	uint8_t res_16;
+	uint8_t timebases;		/* 17 MTb and FTB */
+	uint8_t tck_min;		/* 18 tCKAVGmin */
+	uint8_t tck_max;		/* 19 TCKAVGmax */
+	uint8_t caslat_b1;		/* 20 CAS latencies, 1st byte */
+	uint8_t caslat_b2;		/* 21 CAS latencies, 2nd byte */
+	uint8_t caslat_b3;		/* 22 CAS latencies, 3rd byte */
+	uint8_t caslat_b4;		/* 23 CAS latencies, 4th byte */
+	uint8_t taa_min;		/* 24 Min CAS Latency Time */
+	uint8_t trcd_min;		/* 25 Min RAS# to CAS# Delay Time */
+	uint8_t trp_min;		/* 26 Min Row Precharge Delay Time */
+	uint8_t tras_trc_ext;		/* 27 Upper Nibbles for tRAS and tRC */
+	uint8_t tras_min_lsb;		/* 28 tRASmin, lsb */
+	uint8_t trc_min_lsb;		/* 29 tRCmin, lsb */
+	uint8_t trfc1_min_lsb;		/* 30 Min Refresh Recovery Delay Time */
+	uint8_t trfc1_min_msb;		/* 31 Min Refresh Recovery Delay Time */
+	uint8_t trfc2_min_lsb;		/* 32 Min Refresh Recovery Delay Time */
+	uint8_t trfc2_min_msb;		/* 33 Min Refresh Recovery Delay Time */
+	uint8_t trfc4_min_lsb;		/* 34 Min Refresh Recovery Delay Time */
+	uint8_t trfc4_min_msb;		/* 35 Min Refresh Recovery Delay Time */
+	uint8_t tfaw_msb;		/* 36 Upper Nibble for tFAW */
+	uint8_t tfaw_min;		/* 37 tFAW, lsb */
+	uint8_t trrds_min;		/* 38 tRRD_Smin, MTB */
+	uint8_t trrdl_min;		/* 39 tRRD_Lmin, MTB */
+	uint8_t tccdl_min;		/* 40 tCCS_Lmin, MTB */
+	uint8_t res_41[60-41];		/* 41 Rserved */
+	uint8_t mapping[78-60];		/* 60~77 Connector to SDRAM bit map */
+	uint8_t res_78[117-78];		/* 78~116, Reserved */
+	int8_t fine_tccdl_min;		/* 117 Fine offset for tCCD_Lmin */
+	int8_t fine_trrdl_min;		/* 118 Fine offset for tRRD_Lmin */
+	int8_t fine_trrds_min;		/* 119 Fine offset for tRRD_Smin */
+	int8_t fine_trc_min;		/* 120 Fine offset for tRCmin */
+	int8_t fine_trp_min;		/* 121 Fine offset for tRPmin */
+	int8_t fine_trcd_min;		/* 122 Fine offset for tRCDmin */
+	int8_t fine_taa_min;		/* 123 Fine offset for tAAmin */
+	int8_t fine_tck_max;		/* 124 Fine offset for tCKAVGmax */
+	int8_t fine_tck_min;		/* 125 Fine offset for tCKAVGmin */
+	/* CRC: Bytes 126-127 */
+	uint8_t crc[2];			/* 126-127 SPD CRC */
+
+	/* Module-Specific Section: Bytes 128-255 */
+	union {
+		struct {
+			/* 128 (Unbuffered) Module Nominal Height */
+			uint8_t mod_height;
+			/* 129 (Unbuffered) Module Maximum Thickness */
+			uint8_t mod_thickness;
+			/* 130 (Unbuffered) Reference Raw Card Used */
+			uint8_t ref_raw_card;
+			/* 131 (Unbuffered) Address Mapping from
+			      Edge Connector to DRAM */
+			uint8_t addr_mapping;
+			/* 132~253 (Unbuffered) Reserved */
+			uint8_t res_132[254-132];
+			/* 254~255 CRC */
+			uint8_t crc[2];
+		} unbuffered;
+		struct {
+			/* 128 (Registered) Module Nominal Height */
+			uint8_t mod_height;
+			/* 129 (Registered) Module Maximum Thickness */
+			uint8_t mod_thickness;
+			/* 130 (Registered) Reference Raw Card Used */
+			uint8_t ref_raw_card;
+			/* 131 DIMM Module Attributes */
+			uint8_t modu_attr;
+			/* 132 RDIMM Thermal Heat Spreader Solution */
+			uint8_t thermal;
+			/* 133 Register Manufacturer ID Code, LSB */
+			uint8_t reg_id_lo;
+			/* 134 Register Manufacturer ID Code, MSB */
+			uint8_t reg_id_hi;
+			/* 135 Register Revision Number */
+			uint8_t reg_rev;
+			/* 136 Address mapping from register to DRAM */
+			uint8_t reg_map;
+			/* 137~253 Reserved */
+			uint8_t res_137[254-137];
+			/* 254~255 CRC */
+			uint8_t crc[2];
+		} registered;
+		struct {
+			/* 128 (Loadreduced) Module Nominal Height */
+			uint8_t mod_height;
+			/* 129 (Loadreduced) Module Maximum Thickness */
+			uint8_t mod_thickness;
+			/* 130 (Loadreduced) Reference Raw Card Used */
+			uint8_t ref_raw_card;
+			/* 131 DIMM Module Attributes */
+			uint8_t modu_attr;
+			/* 132 RDIMM Thermal Heat Spreader Solution */
+			uint8_t thermal;
+			/* 133 Register Manufacturer ID Code, LSB */
+			uint8_t reg_id_lo;
+			/* 134 Register Manufacturer ID Code, MSB */
+			uint8_t reg_id_hi;
+			/* 135 Register Revision Number */
+			uint8_t reg_rev;
+			/* 136 Address mapping from register to DRAM */
+			uint8_t reg_map;
+			/* 137 Register Output Drive Strength for CMD/Add*/
+			uint8_t reg_drv;
+			/* 138 Register Output Drive Strength for CK */
+			uint8_t reg_drv_ck;
+			/* 139 Data Buffer Revision Number */
+			uint8_t data_buf_rev;
+			/* 140 DRAM VrefDQ for Package Rank 0 */
+			uint8_t vrefqe_r0;
+			/* 141 DRAM VrefDQ for Package Rank 1 */
+			uint8_t vrefqe_r1;
+			/* 142 DRAM VrefDQ for Package Rank 2 */
+			uint8_t vrefqe_r2;
+			/* 143 DRAM VrefDQ for Package Rank 3 */
+			uint8_t vrefqe_r3;
+			/* 144 Data Buffer VrefDQ for DRAM Interface */
+			uint8_t data_intf;
+			/*
+			 * 145 Data Buffer MDQ Drive Strength and RTT
+			 * for data rate <= 1866
+			 */
+			uint8_t data_drv_1866;
+			/*
+			 * 146 Data Buffer MDQ Drive Strength and RTT
+			 * for 1866 < data rate <= 2400
+			 */
+			uint8_t data_drv_2400;
+			/*
+			 * 147 Data Buffer MDQ Drive Strength and RTT
+			 * for 2400 < data rate <= 3200
+			 */
+			uint8_t data_drv_3200;
+			/* 148 DRAM Drive Strength */
+			uint8_t dram_drv;
+			/*
+			 * 149 DRAM ODT (RTT_WR, RTT_NOM)
+			 * for data rate <= 1866
+			 */
+			uint8_t dram_odt_1866;
+			/*
+			 * 150 DRAM ODT (RTT_WR, RTT_NOM)
+			 * for 1866 < data rate <= 2400
+			 */
+			uint8_t dram_odt_2400;
+			/*
+			 * 151 DRAM ODT (RTT_WR, RTT_NOM)
+			 * for 2400 < data rate <= 3200
+			 */
+			uint8_t dram_odt_3200;
+			/*
+			 * 152 DRAM ODT (RTT_PARK)
+			 * for data rate <= 1866
+			 */
+			uint8_t dram_odt_park_1866;
+			/*
+			 * 153 DRAM ODT (RTT_PARK)
+			 * for 1866 < data rate <= 2400
+			 */
+			uint8_t dram_odt_park_2400;
+			/*
+			 * 154 DRAM ODT (RTT_PARK)
+			 * for 2400 < data rate <= 3200
+			 */
+			uint8_t dram_odt_park_3200;
+			uint8_t res_155[254-155];	/* Reserved */
+			/* 254~255 CRC */
+			uint8_t crc[2];
+		} loadreduced;
+		uint8_t uc[128]; /* 128-255 Module-Specific Section */
+	} mod_section;
+
+	uint8_t res_256[320-256];	/* 256~319 Reserved */
+
+	/* Module supplier's data: Byte 320~383 */
+	uint8_t mmid_lsb;		/* 320 Module MfgID Code LSB */
+	uint8_t mmid_msb;		/* 321 Module MfgID Code MSB */
+	uint8_t mloc;			/* 322 Mfg Location */
+	uint8_t mdate[2];		/* 323~324 Mfg Date */
+	uint8_t sernum[4];		/* 325~328 Module Serial Number */
+	uint8_t mpart[20];		/* 329~348 Mfg's Module Part Number */
+	uint8_t mrev;			/* 349 Module Revision Code */
+	uint8_t dmid_lsb;		/* 350 DRAM MfgID Code LSB */
+	uint8_t dmid_msb;		/* 351 DRAM MfgID Code MSB */
+	uint8_t stepping;		/* 352 DRAM stepping */
+	uint8_t msd[29];		/* 353~381 Mfg's Specific Data */
+	uint8_t res_382[2];		/* 382~383 Reserved */
+
+	uint8_t user[512-384];		/* 384~511 End User Programmable */
+};
+
 extern unsigned int ddr1_spd_check(const ddr1_spd_eeprom_t *spd);
 extern void ddr1_spd_dump(const ddr1_spd_eeprom_t *spd);
 extern unsigned int ddr2_spd_check(const ddr2_spd_eeprom_t *spd);
 extern void ddr2_spd_dump(const ddr2_spd_eeprom_t *spd);
 extern unsigned int ddr3_spd_check(const ddr3_spd_eeprom_t *spd);
+unsigned int ddr4_spd_check(const struct ddr4_spd_eeprom_s *spd);
 
 /*
  * Byte 2 Fundamental Memory Types.
@@ -310,6 +519,7 @@ extern unsigned int ddr3_spd_check(const ddr3_spd_eeprom_t *spd);
 #define SPD_MEMTYPE_DDR2_FBDIMM	(0x09)
 #define SPD_MEMTYPE_DDR2_FBDIMM_PROBE	(0x0A)
 #define SPD_MEMTYPE_DDR3	(0x0B)
+#define SPD_MEMTYPE_DDR4	(0x0C)
 
 /* DIMM Type for DDR2 SPD (according to v1.3) */
 #define DDR2_SPD_DIMMTYPE_UNDEFINED	(0x00)
@@ -338,4 +548,18 @@ extern unsigned int ddr3_spd_check(const ddr3_spd_eeprom_t *spd);
 #define DDR3_SPD_MODULETYPE_16B_SO_DIMM	(0x0C)
 #define DDR3_SPD_MODULETYPE_32B_SO_DIMM	(0x0D)
 
+/* DIMM Type for DDR4 SPD */
+#define DDR4_SPD_MODULETYPE_MASK	(0x0f)
+#define DDR4_SPD_MODULETYPE_EXT		(0x00)
+#define DDR4_SPD_MODULETYPE_RDIMM	(0x01)
+#define DDR4_SPD_MODULETYPE_UDIMM	(0x02)
+#define DDR4_SPD_MODULETYPE_SO_DIMM	(0x03)
+#define DDR4_SPD_MODULETYPE_LRDIMM	(0x04)
+#define DDR4_SPD_MODULETYPE_MINI_RDIMM	(0x05)
+#define DDR4_SPD_MODULETYPE_MINI_UDIMM	(0x06)
+#define DDR4_SPD_MODULETYPE_72B_SO_UDIMM	(0x08)
+#define DDR4_SPD_MODULETYPE_72B_SO_RDIMM	(0x09)
+#define DDR4_SPD_MODULETYPE_16B_SO_DIMM	(0x0C)
+#define DDR4_SPD_MODULETYPE_32B_SO_DIMM	(0x0D)
+
 #endif /* _DDR_SPD_H_ */
diff --git a/include/dfu.h b/include/dfu.h
index 6c71ecbe35..240916854a 100644
--- a/include/dfu.h
+++ b/include/dfu.h
@@ -64,11 +64,6 @@ struct ram_internal_data {
 	unsigned int	size;
 };
 
-static inline unsigned int get_mmc_blk_size(int dev)
-{
-	return find_mmc_device(dev)->read_bl_len;
-}
-
 #define DFU_NAME_SIZE			32
 #define DFU_CMD_BUF_SIZE		128
 #ifndef CONFIG_SYS_DFU_DATA_BUF_SIZE
@@ -173,12 +168,5 @@ static inline int dfu_fill_entity_ram(struct dfu_entity *dfu, char *s)
 }
 #endif
 
-#ifdef CONFIG_DFU_FUNCTION
 int dfu_add(struct usb_configuration *c);
-#else
-int dfu_add(struct usb_configuration *c)
-{
-	return 0;
-}
-#endif
 #endif /* __DFU_ENTITY_H_ */
diff --git a/include/e500.h b/include/e500.h
index 0c2432657b..5884a224d2 100644
--- a/include/e500.h
+++ b/include/e500.h
@@ -24,6 +24,9 @@ typedef struct
 #ifdef CONFIG_SYS_DPAA_PME
 	unsigned long freq_pme;
 #endif
+#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+	unsigned char diff_sysclk;
+#endif
 } MPC85xx_SYS_INFO;
 
 #endif  /* _ASMLANGUAGE */
diff --git a/include/environment.h b/include/environment.h
index 46a3554ff9..08679aead9 100644
--- a/include/environment.h
+++ b/include/environment.h
@@ -146,7 +146,12 @@ extern unsigned long nand_env_oob_offset;
 extern char *env_name_spec;
 #endif
 
+#ifdef CONFIG_ENV_AES
+/* Make sure the payload is multiple of AES block size */
+#define ENV_SIZE ((CONFIG_ENV_SIZE - ENV_HEADER_SIZE) & ~(16 - 1))
+#else
 #define ENV_SIZE (CONFIG_ENV_SIZE - ENV_HEADER_SIZE)
+#endif
 
 typedef struct environment_s {
 	uint32_t	crc;		/* CRC32 over data bytes	*/
@@ -154,7 +159,12 @@ typedef struct environment_s {
 	unsigned char	flags;		/* active/obsolete flags	*/
 #endif
 	unsigned char	data[ENV_SIZE]; /* Environment data		*/
-} env_t;
+} env_t
+#ifdef CONFIG_ENV_AES
+/* Make sure the env is aligned to block size. */
+__attribute__((aligned(16)))
+#endif
+;
 
 #ifdef ENV_IS_EMBEDDED
 extern env_t environment;
@@ -201,6 +211,9 @@ int set_default_vars(int nvars, char * const vars[]);
 /* Import from binary representation into hash table */
 int env_import(const char *buf, int check);
 
+/* Export from hash table into binary representation */
+int env_export(env_t *env_out);
+
 #endif /* DO_DEPS_ONLY */
 
 #endif /* _ENVIRONMENT_H_ */
diff --git a/include/fdc.h b/include/fdc.h
deleted file mode 100644
index 207b0e2667..0000000000
--- a/include/fdc.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/*
- * (C) Copyright 2002
- * Stäubli Faverges - <www.staubli.com>
- * Pierre AUBERT  p.aubert@staubli.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _FDC_H_
-#define _FDC_H_
-
-/* Functions prototype                                                       */
-int fdc_fdos_init (int drive);
-int fdc_fdos_seek (int where);
-int fdc_fdos_read (void *buffer, int len);
-
-int dos_open(char *name);
-int dos_read (ulong addr);
-int dos_dir (void);
-
-#endif
diff --git a/include/fdt_support.h b/include/fdt_support.h
index 15eba01662..ae010bb624 100644
--- a/include/fdt_support.h
+++ b/include/fdt_support.h
@@ -12,6 +12,8 @@
 
 #include <libfdt.h>
 
+u32 fdt_getprop_u32_default_node(const void *fdt, int off, int cell,
+				const char *prop, const u32 dflt);
 u32 fdt_getprop_u32_default(const void *fdt, const char *path,
 				const char *prop, const u32 dflt);
 int fdt_chosen(void *fdt, int force);
@@ -92,6 +94,8 @@ int fdt_add_edid(void *blob, const char *compat, unsigned char *buf);
 int fdt_verify_alias_address(void *fdt, int anode, const char *alias,
 			      u64 addr);
 u64 fdt_get_base_address(void *fdt, int node);
+int fdt_read_range(void *fdt, int node, int n, uint64_t *child_addr,
+		   uint64_t *addr, uint64_t *len);
 
 enum fdt_status {
 	FDT_STATUS_OKAY,
@@ -122,4 +126,9 @@ static inline int fdt_status_disabled_by_alias(void *fdt, const char* alias)
 }
 
 #endif /* ifdef CONFIG_OF_LIBFDT */
+
+#ifdef USE_HOSTCC
+int fdtdec_get_int(const void *blob, int node, const char *prop_name,
+		int default_val);
+#endif
 #endif /* ifndef __FDT_SUPPORT_H */
diff --git a/include/fsl_ddr.h b/include/fsl_ddr.h
index 72c0b2e94e..5c49b229da 100644
--- a/include/fsl_ddr.h
+++ b/include/fsl_ddr.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -9,6 +9,7 @@
 #ifndef FSL_DDR_MAIN_H
 #define FSL_DDR_MAIN_H
 
+#include <fsl_ddrc_version.h>
 #include <fsl_ddr_sdram.h>
 #include <fsl_ddr_dimm_params.h>
 
@@ -22,6 +23,10 @@
 #define ddr_out32(a, v)	out_be32(a, v)
 #endif
 
+#define _DDR_ADDR CONFIG_SYS_FSL_DDR_ADDR
+
+u32 fsl_ddr_get_version(void);
+
 #if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM)
 /*
  * Bind the main DDR setup driver's generic names
diff --git a/include/fsl_ddr_dimm_params.h b/include/fsl_ddr_dimm_params.h
index 99a72bc6e1..09a67a6802 100644
--- a/include/fsl_ddr_dimm_params.h
+++ b/include/fsl_ddr_dimm_params.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008 Freescale Semiconductor, Inc.
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -13,7 +13,7 @@
 #define EDC_ECC		2
 #define EDC_AC_PARITY	4
 
-/* Parameters for a DDR2 dimm computed from the SPD */
+/* Parameters for a DDR dimm computed from the SPD */
 typedef struct dimm_params_s {
 
 	/* DIMM organization parameters */
@@ -32,7 +32,12 @@ typedef struct dimm_params_s {
 	unsigned int n_row_addr;
 	unsigned int n_col_addr;
 	unsigned int edc_config;	/* 0 = none, 1 = parity, 2 = ECC */
+#ifdef CONFIG_SYS_FSL_DDR4
+	unsigned int bank_addr_bits;
+	unsigned int bank_group_bits;
+#else
 	unsigned int n_banks_per_sdram_device;
+#endif
 	unsigned int burst_lengths_bitmask;	/* BL=4 bit 2, BL=8 = bit 3 */
 	unsigned int row_density;
 
@@ -43,19 +48,19 @@ typedef struct dimm_params_s {
 
 	/* DIMM timing parameters */
 
-	unsigned int mtb_ps;	/* medium timebase ps, only for ddr3 */
-	unsigned int ftb_10th_ps; /* fine timebase, in 1/10 ps, only for ddr3 */
-	unsigned int taa_ps;	/* minimum CAS latency time, only for ddr3 */
-	unsigned int tfaw_ps;	/* four active window delay, only for ddr3 */
+	int mtb_ps;	/* medium timebase ps */
+	int ftb_10th_ps; /* fine timebase, in 1/10 ps */
+	int taa_ps;	/* minimum CAS latency time */
+	int tfaw_ps;	/* four active window delay */
 
 	/*
 	 * SDRAM clock periods
 	 * The range for these are 1000-10000 so a short should be sufficient
 	 */
-	unsigned int tckmin_x_ps;
-	unsigned int tckmin_x_minus_1_ps;
-	unsigned int tckmin_x_minus_2_ps;
-	unsigned int tckmax_ps;
+	int tckmin_x_ps;
+	int tckmin_x_minus_1_ps;
+	int tckmin_x_minus_2_ps;
+	int tckmax_ps;
 
 	/* SPD-defined CAS latencies */
 	unsigned int caslat_x;
@@ -65,32 +70,46 @@ typedef struct dimm_params_s {
 	unsigned int caslat_lowest_derated;	/* Derated CAS latency */
 
 	/* basic timing parameters */
-	unsigned int trcd_ps;
-	unsigned int trp_ps;
-	unsigned int tras_ps;
-
-	unsigned int twr_ps;	/* maximum = 63750 ps */
-	unsigned int twtr_ps;	/* maximum = 63750 ps */
-	unsigned int trfc_ps;   /* max = 255 ns + 256 ns + .75 ns
+	int trcd_ps;
+	int trp_ps;
+	int tras_ps;
+
+#ifdef CONFIG_SYS_FSL_DDR4
+	int trfc1_ps;
+	int trfc2_ps;
+	int trfc4_ps;
+	int trrds_ps;
+	int trrdl_ps;
+	int tccdl_ps;
+#else
+	int twr_ps;	/* maximum = 63750 ps */
+	int trfc_ps;	/* max = 255 ns + 256 ns + .75 ns
 				       = 511750 ps */
+	int trrd_ps;	/* maximum = 63750 ps */
+	int twtr_ps;	/* maximum = 63750 ps */
+	int trtp_ps;	/* byte 38, spd->trtp */
+#endif
 
-	unsigned int trrd_ps;	/* maximum = 63750 ps */
-	unsigned int trc_ps;	/* maximum = 254 ns + .75 ns = 254750 ps */
+	int trc_ps;	/* maximum = 254 ns + .75 ns = 254750 ps */
 
-	unsigned int refresh_rate_ps;
-	unsigned int extended_op_srt;
+	int refresh_rate_ps;
+	int extended_op_srt;
 
-	/* DDR3 doesn't need these as below */
-	unsigned int tis_ps;	/* byte 32, spd->ca_setup */
-	unsigned int tih_ps;	/* byte 33, spd->ca_hold */
-	unsigned int tds_ps;	/* byte 34, spd->data_setup */
-	unsigned int tdh_ps;	/* byte 35, spd->data_hold */
-	unsigned int trtp_ps;	/* byte 38, spd->trtp */
-	unsigned int tdqsq_max_ps;	/* byte 44, spd->tdqsq */
-	unsigned int tqhs_ps;	/* byte 45, spd->tqhs */
+#if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2)
+	int tis_ps;	/* byte 32, spd->ca_setup */
+	int tih_ps;	/* byte 33, spd->ca_hold */
+	int tds_ps;	/* byte 34, spd->data_setup */
+	int tdh_ps;	/* byte 35, spd->data_hold */
+	int tdqsq_max_ps;	/* byte 44, spd->tdqsq */
+	int tqhs_ps;	/* byte 45, spd->tqhs */
+#endif
 
 	/* DDR3 RDIMM */
 	unsigned char rcw[16];	/* Register Control Word 0-15 */
+#ifdef CONFIG_SYS_FSL_DDR4
+	unsigned int dq_mapping[18];
+	unsigned int dq_mapping_ors;
+#endif
 } dimm_params_t;
 
 extern unsigned int ddr_compute_dimm_parameters(
diff --git a/include/fsl_ddr_sdram.h b/include/fsl_ddr_sdram.h
index 2a36431146..e8a2db91cb 100644
--- a/include/fsl_ddr_sdram.h
+++ b/include/fsl_ddr_sdram.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ * Copyright 2008-2014 Freescale Semiconductor, Inc.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -13,11 +13,13 @@
  * Pick a basic DDR Technology.
  */
 #include <ddr_spd.h>
+#include <fsl_ddrc_version.h>
 
-#define SDRAM_TYPE_DDR1    2
-#define SDRAM_TYPE_DDR2    3
-#define SDRAM_TYPE_LPDDR1  6
-#define SDRAM_TYPE_DDR3    7
+#define SDRAM_TYPE_DDR1		2
+#define SDRAM_TYPE_DDR2		3
+#define SDRAM_TYPE_LPDDR1	6
+#define SDRAM_TYPE_DDR3		7
+#define SDRAM_TYPE_DDR4		5
 
 #define DDR_BL4		4	/* burst length 4 */
 #define DDR_BC4		DDR_BL4	/* burst chop for ddr3 */
@@ -54,6 +56,12 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
 #ifndef CONFIG_FSL_SDRAM_TYPE
 #define CONFIG_FSL_SDRAM_TYPE	SDRAM_TYPE_DDR3
 #endif
+#elif defined(CONFIG_SYS_FSL_DDR4)
+#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR	(3)	/* FIXME */
+typedef struct ddr4_spd_eeprom_s generic_spd_eeprom_t;
+#ifndef CONFIG_FSL_SDRAM_TYPE
+#define CONFIG_FSL_SDRAM_TYPE	SDRAM_TYPE_DDR4
+#endif
 #endif	/* #if defined(CONFIG_SYS_FSL_DDR1) */
 
 #define FSL_DDR_ODT_NEVER		0x0
@@ -116,7 +124,8 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
 
 #define TIMING_CFG_2_CPO_MASK	0x0F800000
 
-#if defined(CONFIG_P4080)
+#if defined(CONFIG_SYS_FSL_DDR_VER) && \
+	(CONFIG_SYS_FSL_DDR_VER > FSL_DDR_VER_4_4)
 #define RD_TO_PRE_MASK		0xf
 #define RD_TO_PRE_SHIFT		13
 #define WR_DATA_DELAY_MASK	0xf
@@ -154,9 +163,27 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
 #define DDR_CDR2_ODT_MASK	0x1
 #define DDR_CDR1_ODT(x) ((x & DDR_CDR1_ODT_MASK) << DDR_CDR1_ODT_SHIFT)
 #define DDR_CDR2_ODT(x) (x & DDR_CDR2_ODT_MASK)
+#define DDR_CDR2_VREF_OVRD(x)	(0x00008080 | ((((x) - 37) & 0x3F) << 8))
 
 #if (defined(CONFIG_SYS_FSL_DDR_VER) && \
 	(CONFIG_SYS_FSL_DDR_VER >= FSL_DDR_VER_4_7))
+#ifdef CONFIG_SYS_FSL_DDR3L
+#define DDR_CDR_ODT_OFF		0x0
+#define DDR_CDR_ODT_120ohm	0x1
+#define DDR_CDR_ODT_200ohm	0x2
+#define DDR_CDR_ODT_75ohm	0x3
+#define DDR_CDR_ODT_60ohm	0x5
+#define DDR_CDR_ODT_46ohm	0x7
+#elif defined(CONFIG_SYS_FSL_DDR4)
+#define DDR_CDR_ODT_OFF		0x0
+#define DDR_CDR_ODT_100ohm	0x1
+#define DDR_CDR_ODT_120OHM	0x2
+#define DDR_CDR_ODT_80ohm	0x3
+#define DDR_CDR_ODT_60ohm	0x4
+#define DDR_CDR_ODT_40ohm	0x5
+#define DDR_CDR_ODT_50ohm	0x6
+#define DDR_CDR_ODT_30ohm	0x7
+#else
 #define DDR_CDR_ODT_OFF		0x0
 #define DDR_CDR_ODT_120ohm	0x1
 #define DDR_CDR_ODT_180ohm	0x2
@@ -165,6 +192,7 @@ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t;
 #define DDR_CDR_ODT_60hm	0x5
 #define DDR_CDR_ODT_70ohm	0x6
 #define DDR_CDR_ODT_47ohm	0x7
+#endif /* DDR3L */
 #else
 #define DDR_CDR_ODT_75ohm	0x0
 #define DDR_CDR_ODT_55ohm	0x1
@@ -188,6 +216,7 @@ typedef struct fsl_ddr_cfg_regs_s {
 	unsigned int timing_cfg_2;
 	unsigned int ddr_sdram_cfg;
 	unsigned int ddr_sdram_cfg_2;
+	unsigned int ddr_sdram_cfg_3;
 	unsigned int ddr_sdram_mode;
 	unsigned int ddr_sdram_mode_2;
 	unsigned int ddr_sdram_mode_3;
@@ -196,6 +225,14 @@ typedef struct fsl_ddr_cfg_regs_s {
 	unsigned int ddr_sdram_mode_6;
 	unsigned int ddr_sdram_mode_7;
 	unsigned int ddr_sdram_mode_8;
+	unsigned int ddr_sdram_mode_9;
+	unsigned int ddr_sdram_mode_10;
+	unsigned int ddr_sdram_mode_11;
+	unsigned int ddr_sdram_mode_12;
+	unsigned int ddr_sdram_mode_13;
+	unsigned int ddr_sdram_mode_14;
+	unsigned int ddr_sdram_mode_15;
+	unsigned int ddr_sdram_mode_16;
 	unsigned int ddr_sdram_md_cntl;
 	unsigned int ddr_sdram_interval;
 	unsigned int ddr_data_init;
@@ -204,6 +241,10 @@ typedef struct fsl_ddr_cfg_regs_s {
 	unsigned int ddr_init_ext_addr;
 	unsigned int timing_cfg_4;
 	unsigned int timing_cfg_5;
+	unsigned int timing_cfg_6;
+	unsigned int timing_cfg_7;
+	unsigned int timing_cfg_8;
+	unsigned int timing_cfg_9;
 	unsigned int ddr_zq_cntl;
 	unsigned int ddr_wrlvl_cntl;
 	unsigned int ddr_wrlvl_cntl_2;
@@ -211,6 +252,14 @@ typedef struct fsl_ddr_cfg_regs_s {
 	unsigned int ddr_sr_cntr;
 	unsigned int ddr_sdram_rcw_1;
 	unsigned int ddr_sdram_rcw_2;
+	unsigned int ddr_sdram_rcw_3;
+	unsigned int ddr_sdram_rcw_4;
+	unsigned int ddr_sdram_rcw_5;
+	unsigned int ddr_sdram_rcw_6;
+	unsigned int dq_map_0;
+	unsigned int dq_map_1;
+	unsigned int dq_map_2;
+	unsigned int dq_map_3;
 	unsigned int ddr_eor;
 	unsigned int ddr_cdr1;
 	unsigned int ddr_cdr2;
@@ -225,7 +274,7 @@ typedef struct memctl_options_partial_s {
 	unsigned int all_dimms_burst_lengths_bitmask;
 	unsigned int all_dimms_registered;
 	unsigned int all_dimms_unbuffered;
-	/*	unsigned int lowest_common_SPD_caslat; */
+	/*	unsigned int lowest_common_spd_caslat; */
 	unsigned int all_dimms_minimum_trcd_ps;
 } memctl_options_partial_t;
 
@@ -357,6 +406,10 @@ static int __board_need_mem_reset(void)
 int board_need_mem_reset(void)
 	__attribute__((weak, alias("__board_need_mem_reset")));
 
+void __weak board_mem_sleep_setup(void)
+{
+}
+
 /*
  * The 85xx boards have a common prototype for fixed_sdram so put the
  * declaration here.
diff --git a/include/fsl_ddrc_version.h b/include/fsl_ddrc_version.h
new file mode 100644
index 0000000000..60ba98bf81
--- /dev/null
+++ b/include/fsl_ddrc_version.h
@@ -0,0 +1,18 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __FSL_DDRC_VER_H
+#define __FSL_DDRC_VER_H
+
+/*
+ * Only the versions with distinct features or registers are listed here.
+ */
+#define FSL_DDR_VER_4_4 44
+#define FSL_DDR_VER_4_6 46
+#define FSL_DDR_VER_4_7	47
+#define FSL_DDR_VER_5_0	50
+
+#endif /* __FSL_DDRC_VER_H */
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index a6e3a5dc9a..9814964937 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -187,5 +187,6 @@ static inline int fsl_esdhc_mmc_init(bd_t *bis) { return -ENOSYS; }
 static inline void fdt_fixup_esdhc(void *blob, bd_t *bd) {}
 #endif /* CONFIG_FSL_ESDHC */
 void __noreturn mmc_boot(void);
+void mmc_spl_load_image(uint32_t offs, unsigned int size, void *vdst);
 
 #endif  /* __FSL_ESDHC_H__ */
diff --git a/include/fsl_ifc.h b/include/fsl_ifc.h
index 58a6efdfe0..630e4b4999 100644
--- a/include/fsl_ifc.h
+++ b/include/fsl_ifc.h
@@ -784,6 +784,7 @@ enum ifc_nand_fir_opcodes {
 
 extern void print_ifc_regs(void);
 extern void init_early_memctl_regs(void);
+void init_final_memctl_regs(void);
 
 #define IFC_BASE_ADDR ((struct fsl_ifc *)CONFIG_SYS_IFC_ADDR)
 
diff --git a/include/fsl_immap.h b/include/fsl_immap.h
index 00902cae08..d63cc19fa1 100644
--- a/include/fsl_immap.h
+++ b/include/fsl_immap.h
@@ -1,7 +1,7 @@
 /*
  * Common internal memory map for some Freescale SoCs
  *
- * Copyright 2013 Freescale Semiconductor, Inc.
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -50,7 +50,8 @@ struct ccsr_ddr {
 	u8	res_150[16];
 	u32	timing_cfg_4;		/* SDRAM Timing Configuration 4 */
 	u32	timing_cfg_5;		/* SDRAM Timing Configuration 5 */
-	u8	reg_168[8];
+	u32	timing_cfg_6;		/* SDRAM Timing Configuration 6 */
+	u32	timing_cfg_7;		/* SDRAM Timing Configuration 7 */
 	u32	ddr_zq_cntl;		/* ZQ calibration control*/
 	u32	ddr_wrlvl_cntl;		/* write leveling control*/
 	u8	reg_178[4];
@@ -60,14 +61,40 @@ struct ccsr_ddr {
 	u8	reg_188[8];
 	u32	ddr_wrlvl_cntl_2;	/* write leveling control 2 */
 	u32	ddr_wrlvl_cntl_3;	/* write leveling control 3 */
-	u8	res_198[104];
+	u8	res_198[0x1a0-0x198];
+	u32	ddr_sdram_rcw_3;
+	u32	ddr_sdram_rcw_4;
+	u32	ddr_sdram_rcw_5;
+	u32	ddr_sdram_rcw_6;
+	u8	res_1b0[0x200-0x1b0];
 	u32	sdram_mode_3;		/* SDRAM Mode Configuration 3 */
 	u32	sdram_mode_4;		/* SDRAM Mode Configuration 4 */
 	u32	sdram_mode_5;		/* SDRAM Mode Configuration 5 */
 	u32	sdram_mode_6;		/* SDRAM Mode Configuration 6 */
 	u32	sdram_mode_7;		/* SDRAM Mode Configuration 7 */
 	u32	sdram_mode_8;		/* SDRAM Mode Configuration 8 */
-	u8	res_218[0x908];
+	u8	res_218[0x220-0x218];
+	u32	sdram_mode_9;		/* SDRAM Mode Configuration 9 */
+	u32	sdram_mode_10;		/* SDRAM Mode Configuration 10 */
+	u32	sdram_mode_11;		/* SDRAM Mode Configuration 11 */
+	u32	sdram_mode_12;		/* SDRAM Mode Configuration 12 */
+	u32	sdram_mode_13;		/* SDRAM Mode Configuration 13 */
+	u32	sdram_mode_14;		/* SDRAM Mode Configuration 14 */
+	u32	sdram_mode_15;		/* SDRAM Mode Configuration 15 */
+	u32	sdram_mode_16;		/* SDRAM Mode Configuration 16 */
+	u8	res_240[0x250-0x240];
+	u32	timing_cfg_8;		/* SDRAM Timing Configuration 8 */
+	u32	timing_cfg_9;		/* SDRAM Timing Configuration 9 */
+	u8	res_258[0x260-0x258];
+	u32	sdram_cfg_3;
+	u8	res_264[0x2a0-0x264];
+	u32	deskew_cntl;
+	u8	res_2a4[0x400-0x2a4];
+	u32	dq_map_0;
+	u32	dq_map_1;
+	u32	dq_map_2;
+	u32	dq_map_3;
+	u8	res_410[0xb20-0x410];
 	u32	ddr_dsr1;		/* Debug Status 1 */
 	u32	ddr_dsr2;		/* Debug Status 2 */
 	u32	ddr_cdr1;		/* Control Driver 1 */
diff --git a/include/fsl_usb.h b/include/fsl_usb.h
index 8b63cdd88c..1a6c9c1636 100644
--- a/include/fsl_usb.h
+++ b/include/fsl_usb.h
@@ -48,6 +48,11 @@ struct ccsr_usb_phy {
 #define CONFIG_SYS_FSL_USB_PLLPRG2_PHY2_CLK_EN (1 << 0)
 #define CONFIG_SYS_FSL_USB_PLLPRG2_PHY1_CLK_EN (1 << 1)
 #define CONFIG_SYS_FSL_USB_PLLPRG2_FRAC_LPF_EN (1 << 13)
+#ifdef CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+#define CONFIG_SYS_FSL_USB_PLLPRG2_REF_DIV_INTERNAL_CLK (5 << 4)
+#define CONFIG_SYS_FSL_USB_PLLPRG2_MFI_INTERNAL_CLK (6 << 16)
+#define CONFIG_SYS_FSL_USB_INTERNAL_SOC_CLK_EN (1 << 20)
+#endif
 #define CONFIG_SYS_FSL_USB_PLLPRG2_REF_DIV (1 << 4)
 #define CONFIG_SYS_FSL_USB_PLLPRG2_MFI (5 << 16)
 #define CONFIG_SYS_FSL_USB_PLLPRG2_PLL_EN (1 << 21)
diff --git a/include/g_dnl.h b/include/g_dnl.h
index 8f813c21ee..1b1b35e0e1 100644
--- a/include/g_dnl.h
+++ b/include/g_dnl.h
@@ -10,7 +10,31 @@
 
 #include <linux/usb/ch9.h>
 #include <linux/usb/gadget.h>
+#include <linux/usb/composite.h>
+#include <linker_lists.h>
+
+/*
+ * @usb_fname: unescaped USB function name
+ * @callback_ptr: bind callback, one per function name
+ */
+#define DECLARE_GADGET_BIND_CALLBACK(usb_fname, callback_ptr) \
+	ll_entry_declare(struct g_dnl_bind_callback, \
+			__usb_function_name_##usb_fname, \
+			g_dnl_bind_callbacks) = { \
+				.usb_function_name = #usb_fname, \
+				.fptr = callback_ptr \
+			}
+
+typedef int (*g_dnl_bind_callback_f)(struct usb_configuration *);
+
+/* used in Gadget downloader callback linker list */
+struct g_dnl_bind_callback {
+	const char *usb_function_name;
+	g_dnl_bind_callback_f fptr;
+};
+
 int g_dnl_bind_fixup(struct usb_device_descriptor *, const char *);
+int g_dnl_board_usb_cable_connected(void);
 int g_dnl_register(const char *s);
 void g_dnl_unregister(void);
 void g_dnl_set_serialnumber(char *);
diff --git a/include/hash.h b/include/hash.h
index e92d27218c..dc21678045 100644
--- a/include/hash.h
+++ b/include/hash.h
@@ -27,6 +27,42 @@ struct hash_algo {
 	void (*hash_func_ws)(const unsigned char *input, unsigned int ilen,
 		unsigned char *output, unsigned int chunk_sz);
 	int chunk_size;				/* Watchdog chunk size */
+	/*
+	 * hash_init: Create the context for progressive hashing
+	 *
+	 * @algo: Pointer to the hash_algo struct
+	 * @ctxp: Pointer to the pointer of the context for hashing
+	 * @return 0 if ok, -1 on error
+	 */
+	int (*hash_init)(struct hash_algo *algo, void **ctxp);
+	/*
+	 * hash_update: Perform hashing on the given buffer
+	 *
+	 * The context is freed by this function if an error occurs.
+	 *
+	 * @algo: Pointer to the hash_algo struct
+	 * @ctx: Pointer to the context for hashing
+	 * @buf: Pointer to the buffer being hashed
+	 * @size: Size of the buffer being hashed
+	 * @is_last: 1 if this is the last update; 0 otherwise
+	 * @return 0 if ok, -1 on error
+	 */
+	int (*hash_update)(struct hash_algo *algo, void *ctx, const void *buf,
+			   unsigned int size, int is_last);
+	/*
+	 * hash_finish: Write the hash result to the given buffer
+	 *
+	 * The context is freed by this function.
+	 *
+	 * @algo: Pointer to the hash_algo struct
+	 * @ctx: Pointer to the context for hashing
+	 * @dest_buf: Pointer to the buffer for the result
+	 * @size: Size of the buffer for the result
+	 * @return 0 if ok, -ENOSPC if size of the result buffer is too small
+	 *   or -1 on other errors
+	 */
+	int (*hash_finish)(struct hash_algo *algo, void *ctx, void *dest_buf,
+			   int size);
 };
 
 /*
@@ -77,4 +113,16 @@ int hash_command(const char *algo_name, int flags, cmd_tbl_t *cmdtp, int flag,
 int hash_block(const char *algo_name, const void *data, unsigned int len,
 	       uint8_t *output, int *output_size);
 
+/**
+ * hash_lookup_algo() - Look up the hash_algo struct for an algorithm
+ *
+ * The function returns the pointer to the struct or -EPROTONOSUPPORT if the
+ * algorithm is not available.
+ *
+ * @algo_name: Hash algorithm to look up
+ * @algop: Pointer to the hash_algo struct if found
+ *
+ * @return 0 if ok, -EPROTONOSUPPORT for an unknown algorithm.
+ */
+int hash_lookup_algo(const char *algo_name, struct hash_algo **algop);
 #endif
diff --git a/include/image.h b/include/image.h
index 8095bc8914..b27877870b 100644
--- a/include/image.h
+++ b/include/image.h
@@ -57,13 +57,18 @@ struct lmb;
 #  ifdef CONFIG_SPL_SHA1_SUPPORT
 #   define IMAGE_ENABLE_SHA1	1
 #  endif
+#  ifdef CONFIG_SPL_SHA256_SUPPORT
+#   define IMAGE_ENABLE_SHA256	1
+#  endif
 # else
 #  define CONFIG_CRC32		/* FIT images need CRC32 support */
 #  define CONFIG_MD5		/* and MD5 */
 #  define CONFIG_SHA1		/* and SHA1 */
+#  define CONFIG_SHA256		/* and SHA256 */
 #  define IMAGE_ENABLE_CRC32	1
 #  define IMAGE_ENABLE_MD5	1
 #  define IMAGE_ENABLE_SHA1	1
+#  define IMAGE_ENABLE_SHA256	1
 # endif
 
 #ifndef IMAGE_ENABLE_CRC32
@@ -78,6 +83,10 @@ struct lmb;
 #define IMAGE_ENABLE_SHA1	0
 #endif
 
+#ifndef IMAGE_ENABLE_SHA256
+#define IMAGE_ENABLE_SHA256	0
+#endif
+
 #endif /* CONFIG_FIT */
 
 #ifdef CONFIG_SYS_BOOT_RAMDISK_HIGH
@@ -824,7 +833,8 @@ int calculate_hash(const void *data, int data_len, const char *algo,
 #if defined(CONFIG_FIT_SIGNATURE)
 # ifdef USE_HOSTCC
 #  define IMAGE_ENABLE_SIGN	1
-#  define IMAGE_ENABLE_VERIFY	0
+#  define IMAGE_ENABLE_VERIFY	1
+# include  <openssl/evp.h>
 #else
 #  define IMAGE_ENABLE_SIGN	0
 #  define IMAGE_ENABLE_VERIFY	1
@@ -835,7 +845,9 @@ int calculate_hash(const void *data, int data_len, const char *algo,
 #endif
 
 #ifdef USE_HOSTCC
-# define gd_fdt_blob()		NULL
+void *image_get_host_blob(void);
+void image_set_host_blob(void *host_blob);
+# define gd_fdt_blob()		image_get_host_blob()
 #else
 # define gd_fdt_blob()		(gd->fdt_blob)
 #endif
@@ -864,6 +876,21 @@ struct image_region {
 	int size;
 };
 
+#if IMAGE_ENABLE_VERIFY
+# include <rsa-checksum.h>
+#endif
+struct checksum_algo {
+	const char *name;
+	const int checksum_len;
+	const int pad_len;
+#if IMAGE_ENABLE_SIGN
+	const EVP_MD *(*calculate_sign)(void);
+#endif
+	void (*calculate)(const struct image_region region[],
+			  int region_count, uint8_t *checksum);
+	const uint8_t *rsa_padding;
+};
+
 struct image_sig_algo {
 	const char *name;		/* Name of algorithm */
 
@@ -914,6 +941,9 @@ struct image_sig_algo {
 	int (*verify)(struct image_sign_info *info,
 		      const struct image_region region[], int region_count,
 		      uint8_t *sig, uint sig_len);
+
+	/* pointer to checksum algorithm */
+	struct checksum_algo *checksum;
 };
 
 /**
@@ -979,7 +1009,11 @@ struct image_region *fit_region_make_list(const void *fit,
 
 static inline int fit_image_check_target_arch(const void *fdt, int node)
 {
+#ifndef USE_HOSTCC
 	return fit_image_check_arch(fdt, node, IH_ARCH_DEFAULT);
+#else
+	return 0;
+#endif
 }
 
 #ifdef CONFIG_FIT_VERBOSE
diff --git a/include/linker_lists.h b/include/linker_lists.h
index 997d149b71..557e6273ad 100644
--- a/include/linker_lists.h
+++ b/include/linker_lists.h
@@ -228,7 +228,7 @@
  * and it's name.
  *
  * Example:
- * ll_entry_declare(struct my_sub_cmd, my_sub_cmd, cmd_sub, cmd.sub) = {
+ * ll_entry_declare(struct my_sub_cmd, my_sub_cmd, cmd_sub) = {
  *         .x = 3,
  *         .y = 4,
  * };
diff --git a/include/linux/mtd/blktrans.h b/include/linux/mtd/blktrans.h
deleted file mode 100644
index 32acb6ce9d..0000000000
--- a/include/linux/mtd/blktrans.h
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * (C) 2003 David Woodhouse <dwmw2@infradead.org>
- *
- * Interface to Linux block layer for MTD 'translation layers'.
- *
- */
-
-#ifndef __MTD_TRANS_H__
-#define __MTD_TRANS_H__
-
-/* XXX U-BOOT XXX */
-#if 0
-#include <linux/mutex.h>
-#else
-#include <linux/list.h>
-#endif
-
-struct hd_geometry;
-struct mtd_info;
-struct mtd_blktrans_ops;
-struct file;
-struct inode;
-
-struct mtd_blktrans_dev {
-	struct mtd_blktrans_ops *tr;
-	struct list_head list;
-	struct mtd_info *mtd;
-/* XXX U-BOOT XXX */
-#if 0
-	struct mutex lock;
-#endif
-	int devnum;
-	unsigned long size;
-	int readonly;
-	void *blkcore_priv; /* gendisk in 2.5, devfs_handle in 2.4 */
-};
-
-struct blkcore_priv; /* Differs for 2.4 and 2.5 kernels; private */
-
-struct mtd_blktrans_ops {
-	char *name;
-	int major;
-	int part_bits;
-	int blksize;
-	int blkshift;
-
-	/* Access functions */
-	int (*readsect)(struct mtd_blktrans_dev *dev,
-		    unsigned long block, char *buffer);
-	int (*writesect)(struct mtd_blktrans_dev *dev,
-		     unsigned long block, char *buffer);
-
-	/* Block layer ioctls */
-	int (*getgeo)(struct mtd_blktrans_dev *dev, struct hd_geometry *geo);
-	int (*flush)(struct mtd_blktrans_dev *dev);
-
-	/* Called with mtd_table_mutex held; no race with add/remove */
-	int (*open)(struct mtd_blktrans_dev *dev);
-	int (*release)(struct mtd_blktrans_dev *dev);
-
-	/* Called on {de,}registration and on subsequent addition/removal
-	   of devices, with mtd_table_mutex held. */
-	void (*add_mtd)(struct mtd_blktrans_ops *tr, struct mtd_info *mtd);
-	void (*remove_dev)(struct mtd_blktrans_dev *dev);
-
-	struct list_head devs;
-	struct list_head list;
-	struct module *owner;
-
-	struct mtd_blkcore_priv *blkcore_priv;
-};
-
-extern int register_mtd_blktrans(struct mtd_blktrans_ops *tr);
-extern int deregister_mtd_blktrans(struct mtd_blktrans_ops *tr);
-extern int add_mtd_blktrans_dev(struct mtd_blktrans_dev *dev);
-extern int del_mtd_blktrans_dev(struct mtd_blktrans_dev *dev);
-
-
-#endif /* __MTD_TRANS_H__ */
diff --git a/include/linux/mtd/nftl-user.h b/include/linux/mtd/nftl-user.h
deleted file mode 100644
index 22b8b707e5..0000000000
--- a/include/linux/mtd/nftl-user.h
+++ /dev/null
@@ -1,76 +0,0 @@
-/*
- * $Id: nftl-user.h,v 1.2 2005/11/07 11:14:56 gleixner Exp $
- *
- * Parts of NFTL headers shared with userspace
- *
- */
-
-#ifndef __MTD_NFTL_USER_H__
-#define __MTD_NFTL_USER_H__
-
-/* Block Control Information */
-
-struct nftl_bci {
-	unsigned char ECCSig[6];
-	uint8_t Status;
-	uint8_t Status1;
-}__attribute__((packed));
-
-/* Unit Control Information */
-
-struct nftl_uci0 {
-	uint16_t VirtUnitNum;
-	uint16_t ReplUnitNum;
-	uint16_t SpareVirtUnitNum;
-	uint16_t SpareReplUnitNum;
-} __attribute__((packed));
-
-struct nftl_uci1 {
-	uint32_t WearInfo;
-	uint16_t EraseMark;
-	uint16_t EraseMark1;
-} __attribute__((packed));
-
-struct nftl_uci2 {
-	uint16_t FoldMark;
-	uint16_t FoldMark1;
-	uint32_t unused;
-} __attribute__((packed));
-
-union nftl_uci {
-	struct nftl_uci0 a;
-	struct nftl_uci1 b;
-	struct nftl_uci2 c;
-};
-
-struct nftl_oob {
-	struct nftl_bci b;
-	union nftl_uci u;
-};
-
-/* NFTL Media Header */
-
-struct NFTLMediaHeader {
-	char DataOrgID[6];
-	uint16_t NumEraseUnits;
-	uint16_t FirstPhysicalEUN;
-	uint32_t FormattedSize;
-	unsigned char UnitSizeFactor;
-} __attribute__((packed));
-
-#define MAX_ERASE_ZONES (8192 - 512)
-
-#define ERASE_MARK 0x3c69
-#define SECTOR_FREE 0xff
-#define SECTOR_USED 0x55
-#define SECTOR_IGNORE 0x11
-#define SECTOR_DELETED 0x00
-
-#define FOLD_MARK_IN_PROGRESS 0x5555
-
-#define ZONE_GOOD 0xff
-#define ZONE_BAD_ORIGINAL 0
-#define ZONE_BAD_MARKED 7
-
-
-#endif /* __MTD_NFTL_USER_H__ */
diff --git a/include/linux/mtd/nftl.h b/include/linux/mtd/nftl.h
deleted file mode 100644
index fe22e0dceb..0000000000
--- a/include/linux/mtd/nftl.h
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * (C) 1999-2003 David Woodhouse <dwmw2@infradead.org>
- */
-
-#ifndef __MTD_NFTL_H__
-#define __MTD_NFTL_H__
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/blktrans.h>
-
-#include <linux/mtd/nftl-user.h>
-
-/* these info are used in ReplUnitTable */
-#define BLOCK_NIL	   0xffff /* last block of a chain */
-#define BLOCK_FREE	   0xfffe /* free block */
-#define BLOCK_NOTEXPLORED  0xfffd /* non explored block, only used during mounting */
-#define BLOCK_RESERVED	   0xfffc /* bios block or bad block */
-
-struct NFTLrecord {
-	struct mtd_blktrans_dev mbd;
-	__u16 MediaUnit, SpareMediaUnit;
-	__u32 EraseSize;
-	struct NFTLMediaHeader MediaHdr;
-	int usecount;
-	unsigned char heads;
-	unsigned char sectors;
-	unsigned short cylinders;
-	__u16 numvunits;
-	__u16 lastEUN;			/* should be suppressed */
-	__u16 numfreeEUNs;
-	__u16 LastFreeEUN;		/* To speed up finding a free EUN */
-	int head,sect,cyl;
-	__u16 *EUNtable;		/* [numvunits]: First EUN for each virtual unit  */
-	__u16 *ReplUnitTable;		/* [numEUNs]: ReplUnitNumber for each */
-	unsigned int nb_blocks;		/* number of physical blocks */
-	unsigned int nb_boot_blocks;	/* number of blocks used by the bios */
-	struct erase_info instr;
-	struct nand_ecclayout oobinfo;
-};
-
-int NFTL_mount(struct NFTLrecord *s);
-int NFTL_formatblock(struct NFTLrecord *s, int block);
-
-int nftl_read_oob(struct mtd_info *mtd, loff_t offs, size_t len,
-		  size_t *retlen, uint8_t *buf);
-int nftl_write_oob(struct mtd_info *mtd, loff_t offs, size_t len,
-		   size_t *retlen, uint8_t *buf);
-
-#ifndef NFTL_MAJOR
-#define NFTL_MAJOR 93
-#endif
-
-#define MAX_NFTLS 16
-#define MAX_SECTORS_PER_UNIT 64
-#define NFTL_PARTN_BITS 4
-
-#endif /* __MTD_NFTL_H__ */
diff --git a/include/mmc.h b/include/mmc.h
index 42d01251b5..bc11f45a6f 100644
--- a/include/mmc.h
+++ b/include/mmc.h
@@ -12,6 +12,7 @@
 
 #include <linux/list.h>
 #include <linux/compiler.h>
+#include <part.h>
 
 #define SD_VERSION_SD	0x20000
 #define SD_VERSION_3	(SD_VERSION_SD | 0x300)
diff --git a/include/netdev.h b/include/netdev.h
index 32b5073ef0..e211f1841f 100644
--- a/include/netdev.h
+++ b/include/netdev.h
@@ -54,7 +54,6 @@ int ftmac100_initialize(bd_t *bits);
 int ftmac110_initialize(bd_t *bits);
 int greth_initialize(bd_t *bis);
 void gt6426x_eth_initialize(bd_t *bis);
-int inca_switch_initialize(bd_t *bis);
 int ks8695_eth_initialize(void);
 int ks8851_mll_initialize(u8 dev_num, int base_addr);
 int lan91c96_initialize(u8 dev_num, int base_addr);
diff --git a/include/part.h b/include/part.h
index 4beb6db89b..53532dcd61 100644
--- a/include/part.h
+++ b/include/part.h
@@ -8,6 +8,7 @@
 #define _PART_H
 
 #include <ide.h>
+#include <common.h>
 
 typedef struct block_dev_desc {
 	int		if_type;	/* type of the interface */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index ce8c8ed5e9..952a67c17c 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -22,10 +22,8 @@
 #if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B)
 
 					/* The RPX series use SLOT_B	*/
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
+#if defined(CONFIG_RPXLITE)
 # define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_ADS)		/* The ADS  board uses SLOT_A	*/
-# define CONFIG_PCMCIA_SLOT_A
 #elif defined(CONFIG_FADS)		/* The FADS series are a mess	*/
 # if defined(CONFIG_MPC86x) || defined(CONFIG_MPC821)
 #  define CONFIG_PCMCIA_SLOT_A
diff --git a/include/rsa-checksum.h b/include/rsa-checksum.h
new file mode 100644
index 0000000000..612db85fe0
--- /dev/null
+++ b/include/rsa-checksum.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright (c) 2013, Andreas Oetken.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+*/
+
+#ifndef _RSA_CHECKSUM_H
+#define _RSA_CHECKSUM_H
+
+#include <errno.h>
+#include <image.h>
+#include <sha1.h>
+#include <sha256.h>
+
+extern const uint8_t padding_sha256_rsa4096[];
+extern const uint8_t padding_sha256_rsa2048[];
+extern const uint8_t padding_sha1_rsa2048[];
+
+void sha256_calculate(const struct image_region region[], int region_count,
+		      uint8_t *checksum);
+void sha1_calculate(const struct image_region region[], int region_count,
+		    uint8_t *checksum);
+
+#endif
diff --git a/include/rsa.h b/include/rsa.h
index add4c789f3..a5680ab88c 100644
--- a/include/rsa.h
+++ b/include/rsa.h
@@ -15,6 +15,20 @@
 #include <errno.h>
 #include <image.h>
 
+/**
+ * struct rsa_public_key - holder for a public key
+ *
+ * An RSA public key consists of a modulus (typically called N), the inverse
+ * and R^2, where R is 2^(# key bits).
+ */
+
+struct rsa_public_key {
+	uint len;		/* len of modulus[] in number of uint32_t */
+	uint32_t n0inv;		/* -1 / modulus[0] mod 2^32 */
+	uint32_t *modulus;	/* modulus as little endian array */
+	uint32_t *rr;		/* R^2 as little endian array */
+};
+
 #if IMAGE_ENABLE_SIGN
 /**
  * sign() - calculate and return signature for given input data
@@ -89,4 +103,14 @@ static inline int rsa_verify(struct image_sign_info *info,
 }
 #endif
 
+#define RSA2048_BYTES	(2048 / 8)
+#define RSA4096_BYTES	(4096 / 8)
+
+/* This is the minimum/maximum key size we support, in bits */
+#define RSA_MIN_KEY_BITS	2048
+#define RSA_MAX_KEY_BITS	4096
+
+/* This is the maximum signature length that we support, in bits */
+#define RSA_MAX_SIG_BITS	4096
+
 #endif
diff --git a/include/spi_flash.h b/include/spi_flash.h
index 1a11286224..2db53c74c8 100644
--- a/include/spi_flash.h
+++ b/include/spi_flash.h
@@ -158,5 +158,6 @@ static inline int spi_flash_erase(struct spi_flash *flash, u32 offset,
 }
 
 void spi_boot(void) __noreturn;
+void spi_spl_load_image(uint32_t offs, unsigned int size, void *vdst);
 
 #endif /* _SPI_FLASH_H_ */
diff --git a/include/thor.h b/include/thor.h
index afeade4564..5051be714b 100644
--- a/include/thor.h
+++ b/include/thor.h
@@ -15,13 +15,5 @@
 
 int thor_handle(void);
 int thor_init(void);
-
-#ifdef CONFIG_THOR_FUNCTION
 int thor_add(struct usb_configuration *c);
-#else
-int thor_add(struct usb_configuration *c)
-{
-	return 0;
-}
-#endif
 #endif /* __THOR_H_ */
diff --git a/include/usb.h b/include/usb.h
index 736730e896..d9fedeeff7 100644
--- a/include/usb.h
+++ b/include/usb.h
@@ -197,16 +197,6 @@ int board_usb_init(int index, enum usb_init_type init);
  */
 int board_usb_cleanup(int index, enum usb_init_type init);
 
-/*
- * If CONFIG_USB_CABLE_CHECK is set then this function
- * should be defined in board file.
- *
- * @return 1 if cable is connected and 0 otherwise.
- */
-#ifdef CONFIG_USB_CABLE_CHECK
-int usb_cable_connected(void);
-#endif
-
 #ifdef CONFIG_USB_STORAGE
 
 #define USB_MAX_STOR_DEV 5
diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-fsl.h
index 734305b9db..c9ee1d5bf6 100644
--- a/include/usb/ehci-fsl.h
+++ b/include/usb/ehci-fsl.h
@@ -164,6 +164,13 @@
 #endif
 
 /*
+ * Increasing TX FIFO threshold value from 2 to 4 decreases
+ * data burst rate with which data packets are posted from the TX
+ * latency FIFO to compensate for latencies in DDR pipeline during DMA
+ */
+#define TXFIFOTHRESH		4
+
+/*
  * USB Registers
  */
 struct usb_ehci {
diff --git a/include/usb_mass_storage.h b/include/usb_mass_storage.h
index 058dcf1174..ed460644c1 100644
--- a/include/usb_mass_storage.h
+++ b/include/usb_mass_storage.h
@@ -40,13 +40,5 @@ int fsg_init(struct ums *);
 void fsg_cleanup(void);
 struct ums *ums_init(unsigned int);
 int fsg_main_thread(void *);
-
-#ifdef CONFIG_USB_GADGET_MASS_STORAGE
 int fsg_add(struct usb_configuration *c);
-#else
-int fsg_add(struct usb_configuration *c)
-{
-	return 0;
-}
-#endif
 #endif /* __USB_MASS_STORAGE_H__ */