Add support for TQM8560 board

2 files changed, 424 insertions, 8 deletions

diff --git a/include/configs/TQM8540.h b/include/configs/TQM8540.h
index 7dd067ef6f..d28d2f311e 100644
--- a/include/configs/TQM8540.h
+++ b/include/configs/TQM8540.h
@@ -47,7 +47,6 @@
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
 #define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
 
-
 /*
  * sysclk for MPC85xx
  *
@@ -66,7 +65,6 @@
 #define CONFIG_SYS_CLK_FREQ	33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -80,16 +78,14 @@
 #define CFG_MEMTEST_START	0x00000000	/* memtest region */
 #define CFG_MEMTEST_END		0x10000000
 
-
 /*
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
 #define CFG_CCSRBAR_DEFAULT	0xFF700000	/* CCSRBAR Default */
-#define CFG_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
+#define CFG_CCSRBAR		0xE0000000	/* relocated CCSRBAR */
 #define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
 
-
 /*
  * DDR Setup
  */
@@ -116,7 +112,6 @@
     #define CFG_DDR_INTERVAL	0x05160100	/* autocharge,no open page */
 #endif
 
-
 /*
  * Flash on the Local Bus
  */
@@ -339,8 +334,8 @@
 
 #define CONFIG_COMMANDS        (CONFIG_CMD_PRIV	| \
 				ADD_PCI_CMD	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_I2C	)
+				CFG_CMD_I2C	| \
+				CFG_CMD_PING	)
 #include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled */
diff --git a/include/configs/TQM8560.h b/include/configs/TQM8560.h
new file mode 100644
index 0000000000..4e395d5819
--- /dev/null
+++ b/include/configs/TQM8560.h
@@ -0,0 +1,421 @@
+/*
+ * Copyright 2005 DENX Software Engineering
+ * Wolfgang Denk <wd@denx.de>
+ * Copyright 2004 Freescale Semiconductor.
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * TQM8560 board configuration file
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560 */
+#define CONFIG_MPC8560		1	/* MPC8560 specific */
+#define CONFIG_TQM8560		1	/* TQM8560 board specific */
+
+#undef CONFIG_PCI
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_DLL			/* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING		/* Sets the 2T timing bit */
+
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ *    33000000
+ *    66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz.  In any event, this value
+ * must match the settings of some switches.  Details can be found
+ * in the README.mpc85xxads.
+ */
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ	33000000
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+
+#undef	CFG_DRAM_TEST			/* memory test, takes time */
+#define CFG_MEMTEST_START	0x00000000	/* memtest region */
+#define CFG_MEMTEST_END		0x10000000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT	0xFF700000	/* CCSRBAR Default */
+#define CFG_CCSRBAR		0xE0000000	/* relocated CCSRBAR */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+#if defined(CONFIG_SPD_EEPROM)
+    /*
+     * Determine DDR configuration from I2C interface.
+     */
+    #define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
+
+#else
+    /*
+     * Manually set up DDR parameters
+     */
+    #define CFG_SDRAM_SIZE	512		/* DDR is 256MB */
+    #define CFG_DDR_CS0_BNDS	0x0000001f	/* 0-256MB */
+    #define CFG_DDR_CS0_CONFIG	0x80000102
+    #define CFG_DDR_TIMING_1	0x47445331
+    #define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+    #define CFG_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
+    #define CFG_DDR_MODE	0x40020062	/* DLL,normal,seq,4/2.5 */
+    #define CFG_DDR_INTERVAL	0x05160100	/* autocharge,no open page */
+#endif
+
+/*
+ * Flash on the Local Bus
+ */
+#define CFG_LBC_FLASH_BASE	0xfe000000	/* Localbus SDRAM */
+#define CFG_LBC_FLASH_SIZE	32		/* LBC SDRAM is 32MB */
+
+#define CFG_FLASH_BASE		CFG_LBC_FLASH_BASE	/* start of FLASH 32M */
+#define CFG_BR0_PRELIM		0xfe001801	/* port size 32bit */
+
+#define CFG_OR0_PRELIM		0xfe000040	/* 32MB Flash */
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
+#define CFG_MAX_FLASH_SECT	256		/* sectors per device */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef	CFG_RAMBOOT
+#endif
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#define CFG_LBC_LCRR		0x00030008    /* LB clock ratio reg */
+#define CFG_LBC_LBCR		0x00000000    /* LB config reg */
+#define CFG_LBC_LSRT		0x20000000    /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR		0x20000000    /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5	(3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3	(3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2	(2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD	(1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON	( CFG_LBC_LSDMR_BSMA1516	\
+				| CFG_LBC_LSDMR_RFCR5		\
+				| CFG_LBC_LSDMR_PRETOACT3	\
+				| CFG_LBC_LSDMR_ACTTORW3	\
+				| CFG_LBC_LSDMR_BL8		\
+				| CFG_LBC_LSDMR_WRC2		\
+				| CFG_LBC_LSDMR_CL3		\
+				| CFG_LBC_LSDMR_RFEN		\
+				)
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
+				| CFG_LBC_LSDMR_OP_NORMAL)
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK	1
+#define CFG_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
+#define CFG_INIT_RAM_END	0x4000		/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE	128		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_ON_SCC      /* define if console on SCC */
+#undef  CONFIG_CONS_NONE        /* define if console on something else */
+#define CONFIG_CONS_INDEX       1  /* which serial channel for console */
+
+#define CONFIG_BAUDRATE         115200
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef	CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define	 CONFIG_HARD_I2C		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
+
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE	0xc0000000	/* base address */
+#define CFG_RIO_MEM_PHYS	CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE	0x20000000	/* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE	0x80000000
+#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
+#define CFG_PCI1_IO_BASE	0xe2000000
+#define CFG_PCI1_IO_PHYS	CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE	0x1000000	/* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+    #define PCI_ENET0_IOADDR	0xe0000000
+    #define PCI_ENET0_MEMADDR	0xe0000000
+    #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI	1
+#endif
+
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MPC85XX_TSEC2	1
+#define TSEC2_PHY_ADDR		1
+#define TSEC2_PHYIDX		0
+
+#define CONFIG_ETHER_ON_FCC
+#define CONFIG_ETHER_ON_FCC3
+#define CFG_CMXFCR_MASK3      (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK)
+#define CFG_CMXFCR_VALUE3     (CMXFCR_RF2CS_CLK15 | CMXFCR_TF2CS_CLK14)
+#define CFG_CPMFCR_RAMTYPE    0
+#define CFG_FCC_PSMR          (FCC_PSMR_FDE)
+
+#define CONFIG_ETHPRIME		"ENET1"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+  #define CFG_ENV_IS_IN_FLASH	1
+  #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x20000)
+  #define CFG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
+  #define CFG_ENV_SIZE		0x2000
+  #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE)
+  #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#else
+  #define CFG_NO_FLASH		1	/* Flash is not usable now */
+  #define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+  #define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+  #define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
+
+#if defined(CFG_RAMBOOT)
+# define CONFIG_CMD_PRIV	(CONFIG_CMD_DFL & ~(CFG_CMD_ENV  | CFG_CMD_LOADS))
+#else
+# define CONFIG_CMD_PRIV       (CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_NFS	| \
+				CFG_CMD_SNTP	)
+#endif
+
+#if defined(CONFIG_PCI)
+# define ADD_PCI_CMD		(CFG_CMD_PCI)
+#else
+# define ADD_PCI_CMD		0
+#endif
+
+#define CONFIG_COMMANDS        (CONFIG_CMD_PRIV	| \
+				ADD_PCI_CMD	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_PING	)
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory */
+#define CFG_LOAD_ADDR	0x2000000	/* default load address */
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+    #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+    #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+
+#define CONFIG_LOADADDR	 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 5	/* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+
+#undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"consdev=ttyS0\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=$serverip:$rootpath\0"				\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs $bootargs "				\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask"		\
+		":$hostname:$netdev:off panic=1\0"			\
+	"addcons=setenv bootargs $bootargs "				\
+		"console=$consdev,$baudrate\0"				\
+	"flash_nfs=run nfsargs addip addcons;"				\
+		"bootm $kernel_addr\0"					\
+	"flash_self=run ramargs addip addcons;"				\
+		"bootm $kernel_addr $ramdisk_addr\0"			\
+	"net_nfs=tftp $loadaddr $bootfile;"				\
+		"run nfsargs addip addcons;bootm\0"			\
+	"rootpath=/opt/eldk/ppc_85xx\0"					\
+	"bootfile=/tftpboot/tqm8560/uImage\0"				\
+	"kernel_addr=FE000000\0"					\
+	"ramdisk_addr=FE100000\0"					\
+	""
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#endif	/* __CONFIG_H */