summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--board/wandboard/spl.c92
-rw-r--r--board/wandboard/wandboard.c97
-rw-r--r--configs/wandboard_defconfig1
3 files changed, 93 insertions, 97 deletions
diff --git a/board/wandboard/spl.c b/board/wandboard/spl.c
index 9c3350019c..000cb109fc 100644
--- a/board/wandboard/spl.c
+++ b/board/wandboard/spl.c
@@ -422,4 +422,96 @@ void board_init_f(ulong dummy)
/* DDR initialization */
spl_dram_init();
}
+
+#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC3_BASE_ADDR},
+ {USDHC1_BASE_ADDR},
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ /* Carrier MicroSD Card Detect */
+ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ /* SOM MicroSD Card Detect */
+ IOMUX_PADS(PAD_EIM_DA9__GPIO3_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = !gpio_get_value(USDHC1_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+ u32 index = 0;
+
+ /*
+ * Following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 SOM MicroSD
+ * mmc1 Carrier board MicroSD
+ */
+ for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
+ switch (index) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc3_pads);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[0].max_bus_width = 4;
+ gpio_direction_input(USDHC3_CD_GPIO);
+ break;
+ case 1:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ usdhc_cfg[1].max_bus_width = 4;
+ gpio_direction_input(USDHC1_CD_GPIO);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
#endif
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index c0902abe38..69fbc8b690 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -22,8 +22,6 @@
#include <asm/io.h>
#include <linux/sizes.h>
#include <common.h>
-#include <fsl_esdhc.h>
-#include <mmc.h>
#include <miiphy.h>
#include <netdev.h>
#include <phy.h>
@@ -37,10 +35,6 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
@@ -48,8 +42,6 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9)
#define ETH_PHY_RESET IMX_GPIO_NR(3, 29)
#define ETH_PHY_AR8035_POWER IMX_GPIO_NR(7, 13)
#define REV_DETECTION IMX_GPIO_NR(2, 28)
@@ -68,28 +60,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-static iomux_v3_cfg_t const usdhc1_pads[] = {
- IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- /* Carrier MicroSD Card Detect */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- /* SOM MicroSD Card Detect */
- IOMUX_PADS(PAD_EIM_DA9__GPIO3_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
static iomux_v3_cfg_t const enet_pads[] = {
IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
@@ -145,73 +115,6 @@ static void setup_iomux_enet(void)
udelay(100);
}
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC3_BASE_ADDR},
- {USDHC1_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC1_BASE_ADDR:
- ret = !gpio_get_value(USDHC1_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int ret;
- u32 index = 0;
-
-#if !CONFIG_IS_ENABLED(DM_MMC)
- gpio_request(USDHC1_CD_GPIO, "USDHC1_CD");
- gpio_request(USDHC3_CD_GPIO, "USDHC3_CD");
-#endif
-
- /*
- * Following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 SOM MicroSD
- * mmc1 Carrier board MicroSD
- */
- for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
- switch (index) {
- case 0:
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[0].max_bus_width = 4;
- gpio_direction_input(USDHC3_CD_GPIO);
- break;
- case 1:
- SETUP_IOMUX_PADS(usdhc1_pads);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- usdhc_cfg[1].max_bus_width = 4;
- gpio_direction_input(USDHC1_CD_GPIO);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- index + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
diff --git a/configs/wandboard_defconfig b/configs/wandboard_defconfig
index 9d9fbffbbd..7f64ea65b1 100644
--- a/configs/wandboard_defconfig
+++ b/configs/wandboard_defconfig
@@ -44,6 +44,7 @@ CONFIG_SYS_I2C_MXC=y
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_DM_MMC=y
CONFIG_FSL_ESDHC=y
CONFIG_PHYLIB=y
CONFIG_MII=y
generated by cgit (git 2.34.1) at 2024-12-29 19:12:21 +0000