diff options
| -rw-r--r-- | arch/arm/dts/stm32mp15-ddr.dtsi | 2 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157-pinctrl.dtsi | 270 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157-u-boot.dtsi | 60 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 4 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157a-dk1.dts | 28 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c-dk2.dts | 1 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi | 15 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c-ed1.dts | 201 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi | 3 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c-ev1.dts | 12 | ||||
| -rw-r--r-- | arch/arm/dts/stm32mp157c.dtsi | 208 |
11 files changed, 523 insertions, 281 deletions
diff --git a/arch/arm/dts/stm32mp15-ddr.dtsi b/arch/arm/dts/stm32mp15-ddr.dtsi index 4172c02f0a..479b700c86 100644 --- a/arch/arm/dts/stm32mp15-ddr.dtsi +++ b/arch/arm/dts/stm32mp15-ddr.dtsi @@ -5,7 +5,7 @@ / { soc { - ddr: ddr@0x5A003000{ + ddr: ddr@5A003000 { u-boot,dm-pre-reloc; compatible = "st,stm32mp1-ddr"; diff --git a/arch/arm/dts/stm32mp157-pinctrl.dtsi b/arch/arm/dts/stm32mp157-pinctrl.dtsi index 4c424c488d..9bae85045a 100644 --- a/arch/arm/dts/stm32mp157-pinctrl.dtsi +++ b/arch/arm/dts/stm32mp157-pinctrl.dtsi @@ -14,6 +14,7 @@ ranges = <0 0x50002000 0xa400>; interrupt-parent = <&exti>; st,syscfg = <&exti 0x60 0xff>; + hwlocks = <&hwspinlock 0>; pins-are-numbered; gpioa: gpio@50002000 { @@ -164,6 +165,27 @@ }; }; + cec_pins_sleep_a: cec-sleep-0 { + pins { + pinmux = <STM32_PINMUX('A', 15, ANALOG)>; /* HDMI_CEC */ + }; + }; + + cec_pins_b: cec-1 { + pins { + pinmux = <STM32_PINMUX('B', 6, AF5)>; + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + cec_pins_sleep_b: cec-sleep-1 { + pins { + pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* HDMI_CEC */ + }; + }; + ethernet0_rgmii_pins_a: rgmii-0 { pins1 { pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */ @@ -269,7 +291,14 @@ }; }; - i2c1_pins_b: i2c1-1 { + i2c1_pins_sleep_a: i2c1-1 { + pins { + pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */ + <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */ + }; + }; + + i2c1_pins_b: i2c1-2 { pins { pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */ <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */ @@ -289,7 +318,14 @@ }; }; - i2c2_pins_b: i2c2-1 { + i2c2_pins_sleep_a: i2c2-1 { + pins { + pinmux = <STM32_PINMUX('H', 4, ANALOG)>, /* I2C2_SCL */ + <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */ + }; + }; + + i2c2_pins_b: i2c2-2 { pins { pinmux = <STM32_PINMUX('Z', 0, AF3)>, /* I2C2_SCL */ <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */ @@ -309,6 +345,152 @@ }; }; + i2c5_pins_sleep_a: i2c5-1 { + pins { + pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C5_SCL */ + <STM32_PINMUX('A', 12, ANALOG)>; /* I2C5_SDA */ + + }; + }; + + ltdc_pins_a: ltdc-a-0 { + pins { + pinmux = <STM32_PINMUX('G', 7, AF14)>, /* LCD_CLK */ + <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */ + <STM32_PINMUX('F', 10, AF14)>, /* LCD_DE */ + <STM32_PINMUX('H', 2, AF14)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, AF14)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, AF14)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, AF14)>, /* LCD_R3 */ + <STM32_PINMUX('H', 10, AF14)>, /* LCD_R4 */ + <STM32_PINMUX('C', 0, AF14)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */ + <STM32_PINMUX('E', 5, AF14)>, /* LCD_G0 */ + <STM32_PINMUX('E', 6, AF14)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */ + <STM32_PINMUX('H', 14, AF14)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */ + <STM32_PINMUX('I', 0, AF14)>, /* LCD_G5 */ + <STM32_PINMUX('I', 1, AF14)>, /* LCD_G6 */ + <STM32_PINMUX('I', 2, AF14)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, AF14)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */ + <STM32_PINMUX('I', 4, AF14)>, /* LCD_B4 */ + <STM32_PINMUX('A', 3, AF14)>, /* LCD_B5 */ + <STM32_PINMUX('B', 8, AF14)>, /* LCD_B6 */ + <STM32_PINMUX('D', 8, AF14)>; /* LCD_B7 */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + }; + + ltdc_pins_sleep_a: ltdc-a-1 { + pins { + pinmux = <STM32_PINMUX('G', 7, ANALOG)>, /* LCD_CLK */ + <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, ANALOG)>, /* LCD_VSYNC */ + <STM32_PINMUX('F', 10, ANALOG)>, /* LCD_DE */ + <STM32_PINMUX('H', 2, ANALOG)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, ANALOG)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, ANALOG)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, ANALOG)>, /* LCD_R3 */ + <STM32_PINMUX('H', 10, ANALOG)>, /* LCD_R4 */ + <STM32_PINMUX('C', 0, ANALOG)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */ + <STM32_PINMUX('E', 5, ANALOG)>, /* LCD_G0 */ + <STM32_PINMUX('E', 6, ANALOG)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */ + <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */ + <STM32_PINMUX('I', 0, ANALOG)>, /* LCD_G5 */ + <STM32_PINMUX('I', 1, ANALOG)>, /* LCD_G6 */ + <STM32_PINMUX('I', 2, ANALOG)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, ANALOG)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */ + <STM32_PINMUX('I', 4, ANALOG)>, /* LCD_B4 */ + <STM32_PINMUX('A', 3, ANALOG)>, /* LCD_B5 */ + <STM32_PINMUX('B', 8, ANALOG)>, /* LCD_B6 */ + <STM32_PINMUX('D', 8, ANALOG)>; /* LCD_B7 */ + }; + }; + + ltdc_pins_b: ltdc-b-0 { + pins { + pinmux = <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */ + <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */ + <STM32_PINMUX('K', 7, AF14)>, /* LCD_DE */ + <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */ + <STM32_PINMUX('J', 0, AF14)>, /* LCD_R1 */ + <STM32_PINMUX('J', 1, AF14)>, /* LCD_R2 */ + <STM32_PINMUX('J', 2, AF14)>, /* LCD_R3 */ + <STM32_PINMUX('J', 3, AF14)>, /* LCD_R4 */ + <STM32_PINMUX('J', 4, AF14)>, /* LCD_R5 */ + <STM32_PINMUX('J', 5, AF14)>, /* LCD_R6 */ + <STM32_PINMUX('J', 6, AF14)>, /* LCD_R7 */ + <STM32_PINMUX('J', 7, AF14)>, /* LCD_G0 */ + <STM32_PINMUX('J', 8, AF14)>, /* LCD_G1 */ + <STM32_PINMUX('J', 9, AF14)>, /* LCD_G2 */ + <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */ + <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */ + <STM32_PINMUX('K', 0, AF14)>, /* LCD_G5 */ + <STM32_PINMUX('K', 1, AF14)>, /* LCD_G6 */ + <STM32_PINMUX('K', 2, AF14)>, /* LCD_G7 */ + <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */ + <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */ + <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */ + <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3 */ + <STM32_PINMUX('K', 3, AF14)>, /* LCD_B4 */ + <STM32_PINMUX('K', 4, AF14)>, /* LCD_B5 */ + <STM32_PINMUX('K', 5, AF14)>, /* LCD_B6 */ + <STM32_PINMUX('K', 6, AF14)>; /* LCD_B7 */ + bias-disable; + drive-push-pull; + slew-rate = <1>; + }; + }; + + ltdc_pins_sleep_b: ltdc-b-1 { + pins { + pinmux = <STM32_PINMUX('I', 14, ANALOG)>, /* LCD_CLK */ + <STM32_PINMUX('I', 12, ANALOG)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 13, ANALOG)>, /* LCD_VSYNC */ + <STM32_PINMUX('K', 7, ANALOG)>, /* LCD_DE */ + <STM32_PINMUX('I', 15, ANALOG)>, /* LCD_R0 */ + <STM32_PINMUX('J', 0, ANALOG)>, /* LCD_R1 */ + <STM32_PINMUX('J', 1, ANALOG)>, /* LCD_R2 */ + <STM32_PINMUX('J', 2, ANALOG)>, /* LCD_R3 */ + <STM32_PINMUX('J', 3, ANALOG)>, /* LCD_R4 */ + <STM32_PINMUX('J', 4, ANALOG)>, /* LCD_R5 */ + <STM32_PINMUX('J', 5, ANALOG)>, /* LCD_R6 */ + <STM32_PINMUX('J', 6, ANALOG)>, /* LCD_R7 */ + <STM32_PINMUX('J', 7, ANALOG)>, /* LCD_G0 */ + <STM32_PINMUX('J', 8, ANALOG)>, /* LCD_G1 */ + <STM32_PINMUX('J', 9, ANALOG)>, /* LCD_G2 */ + <STM32_PINMUX('J', 10, ANALOG)>, /* LCD_G3 */ + <STM32_PINMUX('J', 11, ANALOG)>, /* LCD_G4 */ + <STM32_PINMUX('K', 0, ANALOG)>, /* LCD_G5 */ + <STM32_PINMUX('K', 1, ANALOG)>, /* LCD_G6 */ + <STM32_PINMUX('K', 2, ANALOG)>, /* LCD_G7 */ + <STM32_PINMUX('J', 12, ANALOG)>, /* LCD_B0 */ + <STM32_PINMUX('J', 13, ANALOG)>, /* LCD_B1 */ + <STM32_PINMUX('J', 14, ANALOG)>, /* LCD_B2 */ + <STM32_PINMUX('J', 15, ANALOG)>, /* LCD_B3 */ + <STM32_PINMUX('K', 3, ANALOG)>, /* LCD_B4 */ + <STM32_PINMUX('K', 4, ANALOG)>, /* LCD_B5 */ + <STM32_PINMUX('K', 5, ANALOG)>, /* LCD_B6 */ + <STM32_PINMUX('K', 6, ANALOG)>; /* LCD_B7 */ + }; + }; + m_can1_pins_a: m-can1-0 { pins1 { pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */ @@ -322,6 +504,13 @@ }; }; + m_can1_sleep_pins_a: m_can1-sleep@0 { + pins { + pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */ + <STM32_PINMUX('I', 9, ANALOG)>; /* CAN1_RX */ + }; + }; + pwm2_pins_a: pwm2-0 { pins { pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */ @@ -393,7 +582,8 @@ slew-rate = <3>; }; }; - sdmmc1_b4_pins_a: sdmmc1-b4@0 { + + sdmmc1_b4_pins_a: sdmmc1-b4-0 { pins { pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ @@ -407,18 +597,61 @@ }; }; - sdmmc1_dir_pins_a: sdmmc1-dir@0 { + sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + pins2{ + pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-open-drain; + bias-disable; + }; + }; + + sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { pins { + pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */ + }; + }; + + sdmmc1_dir_pins_a: sdmmc1-dir-0 { + pins1 { pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ - <STM32_PINMUX('B', 9, AF11)>, /* SDMMC1_CDIR */ - <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */ + <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */ slew-rate = <3>; drive-push-pull; bias-pull-up; }; + pins2{ + pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */ + bias-pull-up; + }; }; - sdmmc2_b4_pins_a: sdmmc2-b4@0 { + + sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ + <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */ + }; + }; + + sdmmc2_b4_pins_a: sdmmc2-b4-0 { pins { pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */ <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */ @@ -432,7 +665,7 @@ }; }; - sdmmc2_d47_pins_a: sdmmc2-d47@0 { + sdmmc2_d47_pins_a: sdmmc2-d47-0 { pins { pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */ <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */ @@ -444,6 +677,19 @@ }; }; + spdifrx_pins_a: spdifrx-0 { + pins { + pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */ + bias-disable; + }; + }; + + spdifrx_sleep_pins_a: spdifrx-1 { + pins { + pinmux = <STM32_PINMUX('G', 12, ANALOG)>; /* SPDIF_IN1 */ + }; + }; + spi2_pins_a: spi2-0 { pins1 { pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI2_SCK */ @@ -522,6 +768,7 @@ pins-are-numbered; interrupt-parent = <&exti>; st,syscfg = <&exti 0x60 0xff>; + hwlocks = <&hwspinlock 0>; gpioz: gpio@54004000 { gpio-controller; @@ -546,6 +793,13 @@ }; }; + i2c4_pins_sleep_a: i2c4-1 { + pins { + pinmux = <STM32_PINMUX('Z', 4, ANALOG)>, /* I2C4_SCL */ + <STM32_PINMUX('Z', 5, ANALOG)>; /* I2C4_SDA */ + }; + }; + spi1_pins_a: spi1-0 { pins1 { pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */ diff --git a/arch/arm/dts/stm32mp157-u-boot.dtsi b/arch/arm/dts/stm32mp157-u-boot.dtsi index c9f534e4ea..f7c7acc079 100644 --- a/arch/arm/dts/stm32mp157-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157-u-boot.dtsi @@ -21,11 +21,11 @@ pinctrl1 = &pinctrl_z; }; - config { + clocks { u-boot,dm-pre-reloc; }; - clocks { + reboot { u-boot,dm-pre-reloc; }; @@ -35,42 +35,26 @@ }; &bsec { - u-boot,dm-pre-reloc; -}; - -&clk_hsi { - u-boot,dm-pre-reloc; -}; - -&clk_hse { - u-boot,dm-pre-reloc; -}; - -&clk_lse { - u-boot,dm-pre-reloc; -}; - -&clk_lsi { - u-boot,dm-pre-reloc; + u-boot,dm-pre-proper; }; &clk_csi { u-boot,dm-pre-reloc; }; -&rcc { +&clk_hsi { u-boot,dm-pre-reloc; }; -&rcc_reboot { +&clk_hse { u-boot,dm-pre-reloc; }; -&pinctrl { +&clk_lsi { u-boot,dm-pre-reloc; }; -&pinctrl_z { +&clk_lse { u-boot,dm-pre-reloc; }; @@ -134,6 +118,34 @@ u-boot,dm-pre-reloc; }; -&iwdg2 { +&pinctrl { + u-boot,dm-pre-reloc; +}; + +&pinctrl_z { + u-boot,dm-pre-reloc; +}; + +&pwr { u-boot,dm-pre-reloc; }; + +&rcc { + u-boot,dm-pre-reloc; +}; + +&sdmmc1 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; +}; + +&sdmmc2 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; +}; + +&sdmmc3 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; +}; + +&usbotg_hs { + compatible = "st,stm32mp1-hsotg", "snps,dwc2"; +}; diff --git a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi index 0f32a38dc9..36c852d28b 100644 --- a/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi @@ -194,7 +194,3 @@ u-boot,force-b-session-valid; hnp-srp-disable; }; - -&v3v3 { - regulator-always-on; -}; diff --git a/arch/arm/dts/stm32mp157a-dk1.dts b/arch/arm/dts/stm32mp157a-dk1.dts index b8dd4baec5..adb2464920 100644 --- a/arch/arm/dts/stm32mp157a-dk1.dts +++ b/arch/arm/dts/stm32mp157a-dk1.dts @@ -39,12 +39,19 @@ }; }; +&cec { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&cec_pins_b>; + pinctrl-1 = <&cec_pins_sleep_b>; + status = "okay"; +}; + ðernet0 { status = "okay"; pinctrl-0 = <ðernet0_rgmii_pins_a>; pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>; pinctrl-names = "default", "sleep"; - phy-mode = "rgmii"; + phy-mode = "rgmii-id"; max-speed = <1000>; phy-handle = <&phy0>; @@ -58,12 +65,14 @@ }; }; + &i2c4 { pinctrl-names = "default"; pinctrl-0 = <&i2c4_pins_a>; i2c-scl-rising-time-ns = <185>; i2c-scl-falling-time-ns = <20>; status = "okay"; + /* spare dmas for other usage */ /delete-property/dmas; /delete-property/dma-names; @@ -88,17 +97,13 @@ pmic: stpmic@33 { compatible = "st,stpmic1"; reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; interrupt-controller; #interrupt-cells = <2>; status = "okay"; - st,main-control-register = <0x04>; - st,vin-control-register = <0xc0>; - st,usb-control-register = <0x20>; - regulators { compatible = "st,stpmic1-regulators"; - ldo1-supply = <&v3v3>; ldo3-supply = <&vdd_ddr>; ldo6-supply = <&v3v3>; @@ -107,7 +112,7 @@ vddcore: buck1 { regulator-name = "vddcore"; - regulator-min-microvolt = <1200000>; + regulator-min-microvolt = <800000>; regulator-max-microvolt = <1350000>; regulator-always-on; regulator-initial-mode = <0>; @@ -187,7 +192,6 @@ regulator-max-microvolt = <1200000>; regulator-always-on; interrupts = <IT_CURLIM_LDO6 0>; - }; vref_ddr: vref_ddr { @@ -204,7 +208,6 @@ vbus_otg: pwr_sw1 { regulator-name = "vbus_otg"; interrupts = <IT_OCP_OTG 0>; - regulator-active-discharge; }; vbus_sw: pwr_sw2 { @@ -216,8 +219,9 @@ onkey { compatible = "st,stpmic1-onkey"; - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; status = "okay"; }; @@ -250,8 +254,10 @@ }; &sdmmc1 { - pinctrl-names = "default"; + pinctrl-names = "default", "opendrain", "sleep"; pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; broken-cd; st,neg-edge; bus-width = <4>; diff --git a/arch/arm/dts/stm32mp157c-dk2.dts b/arch/arm/dts/stm32mp157c-dk2.dts index 9a81d2d472..020ea0f0e2 100644 --- a/arch/arm/dts/stm32mp157c-dk2.dts +++ b/arch/arm/dts/stm32mp157c-dk2.dts @@ -42,6 +42,7 @@ compatible = "orisetech,otm8009a"; reg = <0>; reset-gpios = <&gpioe 4 GPIO_ACTIVE_LOW>; + power-supply = <&v3v3>; status = "okay"; port { diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi index 55f99037b2..200601edff 100644 --- a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi @@ -156,6 +156,10 @@ }; }; +&sdmmc1 { + u-boot,dm-spl; +}; + &sdmmc1_b4_pins_a { u-boot,dm-spl; pins { @@ -165,12 +169,15 @@ &sdmmc1_dir_pins_a { u-boot,dm-spl; - pins { + pins1 { + u-boot,dm-spl; + }; + pins2 { u-boot,dm-spl; }; }; -&sdmmc1 { +&sdmmc2 { u-boot,dm-spl; }; @@ -188,10 +195,6 @@ }; }; -&sdmmc2 { - u-boot,dm-spl; -}; - &uart4 { u-boot,dm-pre-reloc; }; diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts index ab11c832ec..11981d6dd4 100644 --- a/arch/arm/dts/stm32mp157c-ed1.dts +++ b/arch/arm/dts/stm32mp157c-ed1.dts @@ -19,6 +19,7 @@ }; memory@c0000000 { + device_type = "memory"; reg = <0xC0000000 0x40000000>; }; @@ -40,7 +41,7 @@ }; }; -&hwspinlock { +&dts { status = "okay"; }; @@ -50,23 +51,20 @@ i2c-scl-rising-time-ns = <185>; i2c-scl-falling-time-ns = <20>; status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; - pmic: stpmic1@33 { + pmic: stpmic@33 { compatible = "st,stpmic1"; reg = <0x33>; - interrupts = <0 2>; - interrupt-parent = <&gpioa>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; interrupt-controller; #interrupt-cells = <2>; status = "okay"; - st,main_control_register = <0x04>; - st,vin_control_register = <0xc0>; - st,usb_control_register = <0x30>; - regulators { compatible = "st,stpmic1-regulators"; - ldo1-supply = <&v3v3>; ldo2-supply = <&v3v3>; ldo3-supply = <&vdd_ddr>; @@ -80,20 +78,8 @@ regulator-min-microvolt = <800000>; regulator-max-microvolt = <1350000>; regulator-always-on; - regulator-initial-mode = <2>; + regulator-initial-mode = <0>; regulator-over-current-protection; - - regulator-state-standby { - regulator-on-in-suspend; - regulator-suspend-microvolt = <1200000>; - regulator-mode = <8>; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vdd_ddr: buck2 { @@ -101,22 +87,8 @@ regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on; - regulator-initial-mode = <2>; + regulator-initial-mode = <0>; regulator-over-current-protection; - - regulator-state-standby { - regulator-suspend-microvolt = <1350000>; - regulator-on-in-suspend; - regulator-mode = <8>; - }; - regulator-state-mem { - regulator-suspend-microvolt = <1350000>; - regulator-on-in-suspend; - regulator-mode = <8>; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vdd: buck3 { @@ -124,46 +96,18 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; - st,mask_reset; - regulator-initial-mode = <8>; + st,mask-reset; + regulator-initial-mode = <0>; regulator-over-current-protection; - - regulator-state-standby { - regulator-suspend-microvolt = <3300000>; - regulator-on-in-suspend; - regulator-mode = <8>; - }; - regulator-state-mem { - regulator-suspend-microvolt = <3300000>; - regulator-on-in-suspend; - regulator-mode = <8>; - }; - regulator-state-disk { - regulator-suspend-microvolt = <3300000>; - regulator-on-in-suspend; - regulator-mode = <8>; - }; }; v3v3: buck4 { regulator-name = "v3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - regulator-boot-on; + regulator-always-on; regulator-over-current-protection; - regulator-initial-mode = <8>; - - regulator-state-standby { - regulator-suspend-microvolt = <3300000>; - regulator-unchanged-in-suspend; - regulator-mode = <8>; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; + regulator-initial-mode = <0>; }; vdda: ldo1 { @@ -171,18 +115,6 @@ regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; interrupts = <IT_CURLIM_LDO1 0>; - interrupt-parent = <&pmic>; - - regulator-state-standby { - regulator-suspend-microvolt = <2900000>; - regulator-unchanged-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; v2v8: ldo2 { @@ -190,36 +122,14 @@ regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; interrupts = <IT_CURLIM_LDO2 0>; - interrupt-parent = <&pmic>; - - regulator-state-standby { - regulator-suspend-microvolt = <2800000>; - regulator-unchanged-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vtt_ddr: ldo3 { regulator-name = "vtt_ddr"; - regulator-min-microvolt = <0000000>; - regulator-max-microvolt = <1000000>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; regulator-always-on; regulator-over-current-protection; - - regulator-state-standby { - regulator-off-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vdd_usb: ldo4 { @@ -227,17 +137,6 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; interrupts = <IT_CURLIM_LDO4 0>; - interrupt-parent = <&pmic>; - - regulator-state-standby { - regulator-unchanged-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vdd_sd: ldo5 { @@ -245,19 +144,7 @@ regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; interrupts = <IT_CURLIM_LDO5 0>; - interrupt-parent = <&pmic>; regulator-boot-on; - - regulator-state-standby { - regulator-suspend-microvolt = <2900000>; - regulator-unchanged-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; v1v8: ldo6 { @@ -265,56 +152,43 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; interrupts = <IT_CURLIM_LDO6 0>; - interrupt-parent = <&pmic>; - - regulator-state-standby { - regulator-suspend-microvolt = <1800000>; - regulator-unchanged-in-suspend; - }; - regulator-state-mem { - regulator-off-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; vref_ddr: vref_ddr { regulator-name = "vref_ddr"; regulator-always-on; regulator-over-current-protection; - - regulator-state-standby { - regulator-on-in-suspend; - }; - regulator-state-mem { - regulator-on-in-suspend; - }; - regulator-state-disk { - regulator-off-in-suspend; - }; }; bst_out: boost { regulator-name = "bst_out"; interrupts = <IT_OCP_BOOST 0>; - interrupt-parent = <&pmic>; }; vbus_otg: pwr_sw1 { regulator-name = "vbus_otg"; interrupts = <IT_OCP_OTG 0>; - interrupt-parent = <&pmic>; - regulator-active-discharge; }; vbus_sw: pwr_sw2 { regulator-name = "vbus_sw"; interrupts = <IT_OCP_SWOUT 0>; - interrupt-parent = <&pmic>; regulator-active-discharge; }; }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; }; }; @@ -327,10 +201,6 @@ status = "okay"; }; -&pinctrl { - hwlocks = <&hwspinlock 0>; -}; - &pwr { pwr-supply = <&vdd>; }; @@ -344,7 +214,10 @@ }; &sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>; broken-cd; st,sig-dir; st,neg-edge; @@ -352,11 +225,6 @@ bus-width = <4>; vmmc-supply = <&vdd_sd>; vqmmc-supply = <&sd_switch>; - sd-uhs-sdr12; - sd-uhs-sdr25; - sd-uhs-sdr50; - sd-uhs-ddr50; - sd-uhs-sdr104; status = "okay"; }; @@ -375,6 +243,9 @@ &timers6 { status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; timer@5 { status = "okay"; }; @@ -386,6 +257,10 @@ status = "okay"; }; +&usbotg_hs { + vbus-supply = <&vbus_otg>; +}; + &usbphyc_port0 { phy-supply = <&vdd_usb>; }; diff --git a/arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi index 994092a195..b656eb120d 100644 --- a/arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi +++ b/arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi @@ -56,6 +56,3 @@ }; }; -&v3v3 { - regulator-always-on; -}; diff --git a/arch/arm/dts/stm32mp157c-ev1.dts b/arch/arm/dts/stm32mp157c-ev1.dts index 663e52aa31..ca2a333d43 100644 --- a/arch/arm/dts/stm32mp157c-ev1.dts +++ b/arch/arm/dts/stm32mp157c-ev1.dts @@ -6,6 +6,7 @@ /dts-v1/; #include "stm32mp157c-ed1.dts" +#include <dt-bindings/gpio/gpio.h> / { model = "STMicroelectronics STM32MP157C eval daughter on eval mother"; @@ -157,8 +158,9 @@ }; &m_can1 { - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&m_can1_pins_a>; + pinctrl-1 = <&m_can1_sleep_pins_a>; status = "okay"; }; @@ -194,6 +196,9 @@ }; &timers2 { + /* spare dmas for other usage (un-delete to enable pwm capture) */ + /delete-property/dmas; + /delete-property/dma-names; status = "disabled"; pwm { pinctrl-0 = <&pwm2_pins_a>; @@ -206,6 +211,8 @@ }; &timers8 { + /delete-property/dmas; + /delete-property/dma-names; status = "disabled"; pwm { pinctrl-0 = <&pwm8_pins_a>; @@ -218,6 +225,8 @@ }; &timers12 { + /delete-property/dmas; + /delete-property/dma-names; status = "disabled"; pwm { pinctrl-0 = <&pwm12_pins_a>; @@ -232,7 +241,6 @@ &usbh_ehci { phys = <&usbphyc_port0>; phy-names = "usb"; - vbus-supply = <&vbus_sw>; status = "okay"; }; diff --git a/arch/arm/dts/stm32mp157c.dtsi b/arch/arm/dts/stm32mp157c.dtsi index b9f0eacf71..d15fba0c80 100644 --- a/arch/arm/dts/stm32mp157c.dtsi +++ b/arch/arm/dts/stm32mp157c.dtsi @@ -35,28 +35,6 @@ cpu_on = <0x84000003>; }; - aliases { - gpio0 = &gpioa; - gpio1 = &gpiob; - gpio2 = &gpioc; - gpio3 = &gpiod; - gpio4 = &gpioe; - gpio5 = &gpiof; - gpio6 = &gpiog; - gpio7 = &gpioh; - gpio8 = &gpioi; - gpio9 = &gpioj; - gpio10 = &gpiok; - serial0 = &usart1; - serial1 = &usart2; - serial2 = &usart3; - serial3 = &uart4; - serial4 = &uart5; - serial5 = &usart6; - serial6 = &uart7; - serial7 = &uart8; - }; - intc: interrupt-controller@a0021000 { compatible = "arm,cortex-a7-gic"; #interrupt-cells = <3>; @@ -106,6 +84,38 @@ }; }; + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&dts>; + + trips { + cpu_alert1: cpu-alert1 { + temperature = <85000>; + hysteresis = <0>; + type = "passive"; + }; + + cpu-crit { + temperature = <120000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + }; + }; + }; + + reboot { + compatible = "syscon-reboot"; + regmap = <&rcc>; + offset = <0x404>; + mask = <0x1>; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; @@ -120,6 +130,12 @@ reg = <0x40000000 0x400>; clocks = <&rcc TIM2_K>; clock-names = "int"; + dmas = <&dmamux1 18 0x400 0x1>, + <&dmamux1 19 0x400 0x1>, + <&dmamux1 20 0x400 0x1>, + <&dmamux1 21 0x400 0x1>, + <&dmamux1 22 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up"; status = "disabled"; pwm { @@ -141,6 +157,13 @@ reg = <0x40001000 0x400>; clocks = <&rcc TIM3_K>; clock-names = "int"; + dmas = <&dmamux1 23 0x400 0x1>, + <&dmamux1 24 0x400 0x1>, + <&dmamux1 25 0x400 0x1>, + <&dmamux1 26 0x400 0x1>, + <&dmamux1 27 0x400 0x1>, + <&dmamux1 28 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; status = "disabled"; pwm { @@ -162,6 +185,11 @@ reg = <0x40002000 0x400>; clocks = <&rcc TIM4_K>; clock-names = "int"; + dmas = <&dmamux1 29 0x400 0x1>, + <&dmamux1 30 0x400 0x1>, + <&dmamux1 31 0x400 0x1>, + <&dmamux1 32 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4"; status = "disabled"; pwm { @@ -183,6 +211,13 @@ reg = <0x40003000 0x400>; clocks = <&rcc TIM5_K>; clock-names = "int"; + dmas = <&dmamux1 55 0x400 0x1>, + <&dmamux1 56 0x400 0x1>, + <&dmamux1 57 0x400 0x1>, + <&dmamux1 58 0x400 0x1>, + <&dmamux1 59 0x400 0x1>, + <&dmamux1 60 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; status = "disabled"; pwm { @@ -204,6 +239,8 @@ reg = <0x40004000 0x400>; clocks = <&rcc TIM6_K>; clock-names = "int"; + dmas = <&dmamux1 69 0x400 0x1>; + dma-names = "up"; status = "disabled"; timer@5 { @@ -220,6 +257,8 @@ reg = <0x40005000 0x400>; clocks = <&rcc TIM7_K>; clock-names = "int"; + dmas = <&dmamux1 70 0x400 0x1>; + dma-names = "up"; status = "disabled"; timer@6 { @@ -347,6 +386,19 @@ status = "disabled"; }; + spdifrx: audio-controller@4000d000 { + compatible = "st,stm32h7-spdifrx"; + #sound-dai-cells = <0>; + reg = <0x4000d000 0x400>; + clocks = <&rcc SPDIF_K>; + clock-names = "kclk"; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 93 0x400 0x01>, + <&dmamux1 94 0x400 0x01>; + dma-names = "rx", "rx-ctrl"; + status = "disabled"; + }; + usart2: serial@4000e000 { compatible = "st,stm32h7-uart"; reg = <0x4000e000 0x400>; @@ -487,6 +539,15 @@ reg = <0x44000000 0x400>; clocks = <&rcc TIM1_K>; clock-names = "int"; + dmas = <&dmamux1 11 0x400 0x1>, + <&dmamux1 12 0x400 0x1>, + <&dmamux1 13 0x400 0x1>, + <&dmamux1 14 0x400 0x1>, + <&dmamux1 15 0x400 0x1>, + <&dmamux1 16 0x400 0x1>, + <&dmamux1 17 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", + "up", "trig", "com"; status = "disabled"; pwm { @@ -508,6 +569,15 @@ reg = <0x44001000 0x400>; clocks = <&rcc TIM8_K>; clock-names = "int"; + dmas = <&dmamux1 47 0x400 0x1>, + <&dmamux1 48 0x400 0x1>, + <&dmamux1 49 0x400 0x1>, + <&dmamux1 50 0x400 0x1>, + <&dmamux1 51 0x400 0x1>, + <&dmamux1 52 0x400 0x1>, + <&dmamux1 53 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", + "up", "trig", "com"; status = "disabled"; pwm { @@ -565,6 +635,11 @@ reg = <0x44006000 0x400>; clocks = <&rcc TIM15_K>; clock-names = "int"; + dmas = <&dmamux1 105 0x400 0x1>, + <&dmamux1 106 0x400 0x1>, + <&dmamux1 107 0x400 0x1>, + <&dmamux1 108 0x400 0x1>; + dma-names = "ch1", "up", "trig", "com"; status = "disabled"; pwm { @@ -586,6 +661,9 @@ reg = <0x44007000 0x400>; clocks = <&rcc TIM16_K>; clock-names = "int"; + dmas = <&dmamux1 109 0x400 0x1>, + <&dmamux1 110 0x400 0x1>; + dma-names = "ch1", "up"; status = "disabled"; pwm { @@ -606,6 +684,9 @@ reg = <0x44008000 0x400>; clocks = <&rcc TIM17_K>; clock-names = "int"; + dmas = <&dmamux1 111 0x400 0x1>, + <&dmamux1 112 0x400 0x1>; + dma-names = "ch1", "up"; status = "disabled"; pwm { @@ -706,14 +787,14 @@ m_can1: can@4400e000 { compatible = "bosch,m_can"; - reg = <0x4400e000 0x400>, <0x44011000 0x2800>; + reg = <0x4400e000 0x400>, <0x44011000 0x1400>; reg-names = "m_can", "message_ram"; interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "int0", "int1"; clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; clock-names = "hclk", "cclk"; - bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; + bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; status = "disabled"; }; @@ -811,13 +892,14 @@ }; sdmmc3: sdmmc@48004000 { - compatible = "st,stm32-sdmmc2"; - reg = <0x48004000 0x400>, <0x48005000 0x400>; - reg-names = "sdmmc", "delay"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x48004000 0x400>; + reg-names = "sdmmc"; interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>; clocks = <&rcc SDMMC3_K>; + clock-names = "apb_pclk"; resets = <&rcc SDMMC3_R>; - st,idma = <1>; cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <120000000>; @@ -825,7 +907,7 @@ }; usbotg_hs: usb-otg@49000000 { - compatible = "st,stm32mp1-hsotg", "snps,dwc2"; + compatible = "snps,dwc2"; reg = <0x49000000 0x10000>; clocks = <&rcc USBO_K>; clock-names = "otg"; @@ -846,7 +928,6 @@ reg = <0x4c000000 0x400>; clocks = <&rcc HSEM>; clock-names = "hwspinlock"; - status = "disabled"; }; ipcc: mailbox@4c001000 { @@ -856,9 +937,11 @@ st,proc-id = <0>; interrupts-extended = <&intc GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, - <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "rx", "tx"; + <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <&exti 61 1>; + interrupt-names = "rx", "tx", "wakeup"; clocks = <&rcc IPCC>; + wakeup-source; status = "disabled"; }; @@ -869,13 +952,6 @@ #reset-cells = <1>; }; - rcc_reboot: rcc-reboot@50000000 { - compatible = "syscon-reboot"; - regmap = <&rcc>; - offset = <0x404>; - mask = <0x1>; - }; - pwr: pwr@50001000 { compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd"; reg = <0x50001000 0x400>; @@ -885,7 +961,7 @@ clocks = <&rcc PLL2_R>; clock-names = "phyclk"; - pwr-regulators@c { + pwr-regulators { compatible = "st,stm32mp1,pwr-reg"; st,tzcr = <&rcc 0x0 0x1>; @@ -919,6 +995,7 @@ syscfg: syscon@50020000 { compatible = "st,stm32mp157-syscfg", "syscon"; reg = <0x50020000 0x400>; + clocks = <&rcc SYSCFG>; }; lptimer2: timer@50021000 { @@ -1007,6 +1084,16 @@ status = "disabled"; }; + dts: thermal@50028000 { + compatible = "st,stm32-thermal"; + reg = <0x50028000 0x100>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc TMPSENS>; + clock-names = "pclk"; + #thermal-sensor-cells = <0>; + status = "disabled"; + }; + cryp1: cryp@54001000 { compatible = "st,stm32mp1-cryp"; reg = <0x54001000 0x400>; @@ -1072,26 +1159,27 @@ }; sdmmc1: sdmmc@58005000 { - compatible = "st,stm32-sdmmc2"; - reg = <0x58005000 0x1000>, <0x58006000 0x1000>; - reg-names = "sdmmc", "delay"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x58005000 0x1000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; clocks = <&rcc SDMMC1_K>; + clock-names = "apb_pclk"; resets = <&rcc SDMMC1_R>; - st,idma = <1>; cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <120000000>; - status = "disabled"; }; sdmmc2: sdmmc@58007000 { - compatible = "st,stm32-sdmmc2"; - reg = <0x58007000 0x1000>, <0x58008000 0x1000>; - reg-names = "sdmmc", "delay"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x58007000 0x1000>; interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>; clocks = <&rcc SDMMC2_K>; + clock-names = "apb_pclk"; resets = <&rcc SDMMC2_R>; - st,idma = <1>; cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <120000000>; @@ -1115,25 +1203,21 @@ compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a"; reg = <0x5800a000 0x2000>; reg-names = "stmmaceth"; - interrupts-extended = - <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, - <&intc GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, - <&exti 70 1>; - interrupt-names = "macirq", - "eth_wake_irq", - "stm32_pwr_wakeup"; + interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx", - "ethstp"; + "ethstp", + "syscfg-clk"; clocks = <&rcc ETHMAC>, <&rcc ETHTX>, <&rcc ETHRX>, - <&rcc ETHSTP>; + <&rcc ETHSTP>, + <&rcc SYSCFG>; st,syscon = <&syscfg 0x4>; snps,mixed-burst; snps,pbl = <2>; - snps,en-tx-lpi-clockgating; snps,axi-config = <&stmmac_axi_config_0>; snps,tso; status = "disabled"; @@ -1258,6 +1342,12 @@ reg = <0x5c005000 0x400>; #address-cells = <1>; #size-cells = <1>; + ts_cal1: calib@5c { + reg = <0x5c 0x2>; + }; + ts_cal2: calib@5e { + reg = <0x5e 0x2>; + }; }; i2c6: i2c@5c009000 { |