diff options
| -rw-r--r-- | drivers/usb/Kconfig | 46 | ||||
| -rw-r--r-- | drivers/usb/host/Kconfig | 48 |
2 files changed, 94 insertions, 0 deletions
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index e69de29bb2..b4a9442703 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -0,0 +1,46 @@ +config USB_ARCH_HAS_HCD + def_bool y + +config USB + bool "Support for Host-side USB" + depends on USB_ARCH_HAS_HCD + ---help--- + Universal Serial Bus (USB) is a specification for a serial bus + subsystem which offers higher speeds and more features than the + traditional PC serial port. The bus supplies power to peripherals + and allows for hot swapping. Up to 127 USB peripherals can be + connected to a single USB host in a tree structure. + + The USB host is the root of the tree, the peripherals are the + leaves and the inner nodes are special USB devices called hubs. + Most PCs now have USB host ports, used to connect peripherals + such as scanners, keyboards, mice, modems, cameras, disks, + flash memory, network links, and printers to the PC. + + Say Y here if your computer has a host-side USB port and you want + to use USB devices. You then need to say Y to at least one of the + Host Controller Driver (HCD) options below. Choose a USB 1.1 + controller, such as "UHCI HCD support" or "OHCI HCD support", + and "EHCI HCD (USB 2.0) support" except for older systems that + do not have USB 2.0 support. It doesn't normally hurt to select + them all if you are not certain. + + If your system has a device-side USB port, used in the peripheral + side of the USB protocol, see the "USB Gadget" framework instead. + + After choosing your HCD, then select drivers for the USB peripherals + you'll be using. You may want to check out the information provided + in <file:Documentation/usb/> and especially the links given in + <file:Documentation/usb/usb-help.txt>. + +if USB + +source "drivers/usb/host/Kconfig" + +config USB_STORAGE + bool "USB Mass Storage support" + ---help--- + Say Y here if you want to connect USB mass storage devices to your + board's USB port. + +endif diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig new file mode 100644 index 0000000000..8a6496a6ef --- /dev/null +++ b/drivers/usb/host/Kconfig @@ -0,0 +1,48 @@ +# +# USB Host Controller Drivers +# +comment "USB Host Controller Drivers" + +config USB_XHCI_HCD + bool "xHCI HCD (USB 3.0) support" + ---help--- + The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 + "SuperSpeed" host controller hardware. + +config USB_XHCI + bool + default USB_XHCI_HCD + ---help--- + TODO: rename after most boards switch to Kconfig + +if USB_XHCI_HCD + +endif + +config USB_EHCI_HCD + bool "EHCI HCD (USB 2.0) support" + ---help--- + The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 + "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. + If your USB host controller supports USB 2.0, you will likely want to + configure this Host Controller Driver. + + EHCI controllers are packaged with "companion" host controllers (OHCI + or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports + will connect to EHCI if the device is high speed, otherwise they + connect to a companion controller. If you configure EHCI, you should + probably configure the OHCI (for NEC and some other vendors) USB Host + Controller Driver or UHCI (for Via motherboards) Host Controller + Driver too. + + You may want to read <file:Documentation/usb/ehci.txt>. + +config USB_EHCI + bool + default USB_EHCI_HCD + ---help--- + TODO: rename after most boards switch to Kconfig + +if USB_EHCI_HCD + +endif |