summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--board/sheldon/simpc8313/Makefile8
-rw-r--r--board/sheldon/simpc8313/README.simpc831380
-rw-r--r--board/sheldon/simpc8313/sdram.c177
-rw-r--r--board/sheldon/simpc8313/simpc8313.c150
-rw-r--r--boards.cfg2
-rw-r--r--doc/README.scrapyard21
-rw-r--r--include/configs/SIMPC8313.h580
-rw-r--r--nand_spl/board/sheldon/simpc8313/Makefile81
-rw-r--r--nand_spl/board/sheldon/simpc8313/config.mk5
-rw-r--r--nand_spl/board/sheldon/simpc8313/u-boot.lds38
10 files changed, 11 insertions, 1131 deletions
diff --git a/board/sheldon/simpc8313/Makefile b/board/sheldon/simpc8313/Makefile
deleted file mode 100644
index a824c41d9c..0000000000
--- a/board/sheldon/simpc8313/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := simpc8313.o sdram.o
diff --git a/board/sheldon/simpc8313/README.simpc8313 b/board/sheldon/simpc8313/README.simpc8313
deleted file mode 100644
index b362c6aeea..0000000000
--- a/board/sheldon/simpc8313/README.simpc8313
+++ /dev/null
@@ -1,80 +0,0 @@
-Sheldon Instruments SIMPC8313 Board
------------------------------------------
-
-1. Board Switches and Jumpers
-
- S2 is used to set CFG_RESET_SOURCE.
-
- To boot the image in Large page NAND flash, use these DIP
- switch settings for S2:
-
- +----------+ ON
- | * * **** |
- | * * |
- +----------+
- 12345678
-
- To boot the image in Small page NAND flash, use these DIP
- switch settings for S2:
-
- +----------+ ON
- | *** **** |
- | * |
- +----------+
- 12345678
- (where the '*' indicates the position of the tab of the switch.)
-
-2. Memory Map
- The memory map looks like this:
-
- 0x0000_0000 0x1fff_ffff DDR 512M
- 0x8000_0000 0x8fff_ffff PCI MEM 256M
- 0x9000_0000 0x9fff_ffff PCI_MMIO 256M
- 0xe000_0000 0xe00f_ffff IMMR 1M
- 0xe200_0000 0xe20f_ffff PCI IO 16M
- 0xe280_0000 0xe280_7fff NAND FLASH (CS0) 32K
- or
- 0xe280_0000 0xe281_ffff NAND FLASH (CS0) 128K
- 0xff00_0000 0xff00_7fff FPGA (CS1) 1M
-
-3. Compilation
-
- Assuming you're using BASH (or similar) as your shell:
-
- export CROSS_COMPILE=your-cross-compiler-prefix-
- make distclean
- make SIMPC8313_LP_config
- (or make SIMPC8313_SP_config, depending on the page size
- of your NAND flash)
- make
-
-4. Downloading and Flashing Images
-
-4.1 Reflash U-boot Image using U-boot
-
- =>run update_uboot
-
- You may want to try
- =>tftp $loadaddr $uboot
- first, to make sure that the TFTP load will succeed before it
- goes ahead and wipes out your current firmware. And of course,
- if the new u-boot doesn't boot, you can plug the board into
- your PCI slot and with the supplied driver and sample app
- you can reburn a working u-boot.
-
-4.2 Downloading and Booting Linux Kernel
-
- Ensure that all networking-related environment variables are set
- properly (including ipaddr, serverip, gatewayip (if needed),
- netmask, ethaddr, eth1addr, fdtfile, and bootfile).
-
- =>tftp $loadaddr uImage
- =>nand write $loadaddr kernel $filesize
- =>tftp $loadaddr $fdtfile
- =>nand write $loadaddr 7e0000 1800
-
- =>boot
-
-5 Notes
-
- The console baudrate for SIMPC8313 is 115200bps.
diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c
deleted file mode 100644
index 7c12fe851c..0000000000
--- a/board/sheldon/simpc8313/sdram.c
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
- * Copyright (C) Sheldon Instruments, Inc. 2008
- *
- * Author: Ron Madrid <info@sheldoninst.com>
- *
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc83xx.h>
-#include <spd_sdram.h>
-#include <asm/bitops.h>
-#include <asm/io.h>
-#include <asm/processor.h>
-#include <asm/mmu.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static long fixed_sdram(void);
-
-#if defined(CONFIG_NAND_SPL)
-void si_wait_i2c(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
-
- while (!(__raw_readb(&im->i2c[0].sr) & 0x02))
- ;
-
- __raw_writeb(0x00, &im->i2c[0].sr);
-
- sync();
-
- return;
-}
-
-void si_read_i2c(u32 lbyte, int count, u8 *buffer)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 i;
- u8 chip = 0x50 << 1; /* boot sequencer I2C */
- u32 ubyte = (lbyte & 0xff00) >> 8;
-
- lbyte &= 0xff;
-
- /*
- * Set up controller
- */
- __raw_writeb(0x3f, &im->i2c[0].fdr);
- __raw_writeb(0x00, &im->i2c[0].adr);
- __raw_writeb(0x00, &im->i2c[0].sr);
- __raw_writeb(0x00, &im->i2c[0].dr);
-
- while (__raw_readb(&im->i2c[0].sr) & 0x20)
- ;
-
- /*
- * Writing address to device
- */
- __raw_writeb(0xb0, &im->i2c[0].cr);
- sync();
- __raw_writeb(chip, &im->i2c[0].dr);
- si_wait_i2c();
-
- __raw_writeb(0xb0, &im->i2c[0].cr);
- sync();
- __raw_writeb(ubyte, &im->i2c[0].dr);
- si_wait_i2c();
-
- __raw_writeb(lbyte, &im->i2c[0].dr);
- si_wait_i2c();
-
- __raw_writeb(0xb4, &im->i2c[0].cr);
- sync();
- __raw_writeb(chip + 1, &im->i2c[0].dr);
- si_wait_i2c();
-
- __raw_writeb(0xa0, &im->i2c[0].cr);
- sync();
-
- /*
- * Dummy read
- */
- __raw_readb(&im->i2c[0].dr);
-
- si_wait_i2c();
-
- /*
- * Read actual data
- */
- for (i = 0; i < count; i++)
- {
- if (i == (count - 2)) /* Reached next to last byte, No ACK */
- __raw_writeb(0xa8, &im->i2c[0].cr);
- if (i == (count - 1)) /* Reached last byte, STOP */
- __raw_writeb(0x88, &im->i2c[0].cr);
-
- /* Read byte of data */
- buffer[i] = __raw_readb(&im->i2c[0].dr);
-
- if (i == (count - 1))
- break;
- si_wait_i2c();
- }
-
- return;
-}
-#endif /* CONFIG_NAND_SPL */
-
-phys_size_t initdram(int board_type)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- volatile fsl_lbc_t *lbc = &im->im_lbc;
- u32 msize;
-
- if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im)
- return -1;
-
- /* DDR SDRAM - Main SODIMM */
- __raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar);
-
- msize = fixed_sdram();
-
- /* Local Bus setup lbcr and mrtpr */
- __raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr);
- __raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr);
- sync();
-
- /* return total bus SDRAM size(bytes) -- DDR */
- return (msize * 1024 * 1024);
-}
-
-/*************************************************************************
- * fixed sdram init -- reads values from boot sequencer I2C
- ************************************************************************/
-static long fixed_sdram(void)
-{
- volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
- u32 msizelog2, msize = 1;
-#if defined(CONFIG_NAND_SPL)
- u32 i;
- const u8 bytecount = 135;
- u8 buffer[bytecount];
- u32 addr, data;
-
- si_read_i2c(0, bytecount, buffer);
-
- for (i = 18; i < bytecount; i += 7){
- addr = (u32)buffer[i];
- addr <<= 8;
- addr |= (u32)buffer[i + 1];
- addr <<= 2;
- data = (u32)buffer[i + 2];
- data <<= 8;
- data |= (u32)buffer[i + 3];
- data <<= 8;
- data |= (u32)buffer[i + 4];
- data <<= 8;
- data |= (u32)buffer[i + 5];
-
- __raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr));
- }
-
- sync();
-
- /* enable DDR controller */
- __raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg);
-#endif /* (CONFIG_NAND_SPL) */
-
- msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1);
- msize <<= (msizelog2 - 20);
-
- return msize;
-}
diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c
deleted file mode 100644
index 31406fa66d..0000000000
--- a/board/sheldon/simpc8313/simpc8313.c
+++ /dev/null
@@ -1,150 +0,0 @@
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
- * Copyright (C) Sheldon Instruments, Inc. 2008
- *
- * Author: Ron Madrid <info@sheldoninst.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <libfdt.h>
-#include <pci.h>
-#include <mpc83xx.h>
-#include <ns16550.h>
-#include <nand.h>
-#include <asm/io.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifndef CONFIG_NAND_SPL
-int checkboard(void)
-{
- puts("Board: Sheldon Instruments SIMPC8313\n");
- return 0;
-}
-
-static struct pci_region pci_regions[] = {
- {
- bus_start: CONFIG_SYS_PCI1_MEM_BASE,
- phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
- size: CONFIG_SYS_PCI1_MEM_SIZE,
- flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
- },
- {
- bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
- phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
- size: CONFIG_SYS_PCI1_MMIO_SIZE,
- flags: PCI_REGION_MEM
- },
- {
- bus_start: CONFIG_SYS_PCI1_IO_BASE,
- phys_start: CONFIG_SYS_PCI1_IO_PHYS,
- size: CONFIG_SYS_PCI1_IO_SIZE,
- flags: PCI_REGION_IO
- }
-};
-
-void pci_init_board(void)
-{
- volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
- volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
- volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
- struct pci_region *reg[] = { pci_regions };
-
- /* Enable all 3 PCI_CLK_OUTPUTs. */
- clk->occr |= 0xe0000000;
-
- /*
- * Configure PCI Local Access Windows
- */
- pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR;
- pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB;
-
- pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR;
- pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB;
-
- mpc83xx_pci_init(1, reg);
-}
-
-/*
- * Miscellaneous late-boot configurations
- */
-int misc_init_r(void)
-{
- int rc = 0;
- immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- fsl_lbc_t *lbus = &immap->im_lbc;
- u32 *mxmr = &lbus->mamr; /* Pointer to mamr */
-
- /* UPM Table Configuration Code */
- static uint UPMATable[] = {
- /* Read Single-Beat (RSS) */
- 0x0fff0c00, 0x0fffdc00, 0x0fff0c05, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
- /* Read Burst (RBS) */
- 0x0fff0c00, 0x0ffcdc00, 0x0ffc0c00, 0x0ffc0f0c,
- 0x0ffccf0c, 0x0ffc0f0c, 0x0ffcce0c, 0x3ffc0c05,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
- /* Write Single-Beat (WSS) */
- 0x0ffc0c00, 0x0ffcdc00, 0x0ffc0c05, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
- /* Write Burst (WBS) */
- 0x0ffc0c00, 0x0fffcc0c, 0x0fff0c00, 0x0fffcc00,
- 0x0fff1c00, 0x0fffcf0c, 0x0fff0f0c, 0x0fffcf0c,
- 0x0fff0c0c, 0x0fffcc0c, 0x0fff0c05, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
- /* Refresh Timer (RTS) */
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00,
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01,
- /* Exception Condition (EXS) */
- 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01
- };
-
- upmconfig(UPMA, UPMATable, sizeof(UPMATable) / sizeof(UPMATable[0]));
-
- /* Set LUPWAIT to be active low and enabled */
- out_be32(mxmr, MxMR_UWPL | MxMR_GPL_x4DIS);
-
- return rc;
-}
-
-#if defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
-{
- ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI
- ft_pci_setup(blob, bd);
-#endif
-}
-#endif
-#else /* CONFIG_NAND_SPL */
-void board_init_f(ulong bootflag)
-{
- NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500),
- CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
- puts("NAND boot... ");
- init_timebase();
- initdram(0);
- relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, (gd_t *)gd,
- CONFIG_SYS_NAND_U_BOOT_RELOC);
-}
-
-void board_init_r(gd_t *gd, ulong dest_addr)
-{
- nand_boot();
-}
-
-void putc(char c)
-{
- if (gd->flags & GD_FLG_SILENT)
- return;
-
- if (c == '\n')
- NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r');
-
- NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c);
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index d8646c622a..a58efd6864 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -717,8 +717,6 @@ Active powerpc mpc83xx - keymile km83xx
Active powerpc mpc83xx - keymile km83xx suvd3 suvd3:SUVD3 Holger Brunck <holger.brunck@keymile.com>
Active powerpc mpc83xx - keymile km83xx tuge1 tuxx1:TUGE1 Holger Brunck <holger.brunck@keymile.com>
Active powerpc mpc83xx - keymile km83xx tuxx1 tuxx1:TUXX1 Holger Brunck <holger.brunck@keymile.com>
-Active powerpc mpc83xx - sheldon simpc8313 SIMPC8313_LP SIMPC8313:NAND_LP Ron Madrid <info@sheldoninst.com>
-Active powerpc mpc83xx - sheldon simpc8313 SIMPC8313_SP SIMPC8313:NAND_SP Ron Madrid <info@sheldoninst.com>
Active powerpc mpc83xx - tqc tqm834x TQM834x - -
Active powerpc mpc85xx - - sbc8548 sbc8548 - Paul Gortmaker <paul.gortmaker@windriver.com>
Active powerpc mpc85xx - - sbc8548 sbc8548_PCI_33 sbc8548:PCI,33 Paul Gortmaker <paul.gortmaker@windriver.com>
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index e2157e08be..6c6be68c5a 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,16 +11,17 @@ easily if here is something they might want to dig for...
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
-hidden_dragon powerpc mpc824x - - Yusdi Santoso <yusdi_santoso@adaptec.com>
-debris powerpc mpc824x - - Sangmoon Kim <dogoil@etinsys.com>
-kvme080 powerpc mpc824x - - Sangmoon Kim <dogoil@etinsys.com>
-ep8248 powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
-ispan powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
-rattler powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
-zpc1900 powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
-mpc8260ads powerpc mpc8260 - - Yuli Barcohen <yuli@arabellasw.com>
-adder powerpc mpc8xx - - Yuli Barcohen <yuli@arabellasw.com>
-quad100hd powerpc ppc405ep - - Gary Jennejohn <gljennjohn@googlemail.com>
+simpc8313 powerpc mpc83xx - 2014-04-28 Ron Madrid <info@sheldoninst.com>
+hidden_dragon powerpc mpc824x 3fe1a854 2014-05-30 Yusdi Santoso <yusdi_santoso@adaptec.com>
+debris powerpc mpc824x 7edb1f7b 2014-05-30 Sangmoon Kim <dogoil@etinsys.com>
+kvme080 powerpc mpc824x 2868f862 2014-05-30 Sangmoon Kim <dogoil@etinsys.com>
+ep8248 powerpc mpc8260 49ad566d 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+ispan powerpc mpc8260 80bae39a 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+rattler powerpc mpc8260 d0664db4 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+zpc1900 powerpc mpc8260 6f80bb48 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+mpc8260ads powerpc mpc8260 facb6725 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+adder powerpc mpc8xx 373a9788 2014-05-30 Yuli Barcohen <yuli@arabellasw.com>
+quad100hd powerpc ppc405ep 3569571d 2014-05-30 Gary Jennejohn <gljennjohn@googlemail.com>
lubbock arm pxa 36bf57b 2014-04-18 Kyle Harris <kharris@nexus-tech.net>
EVB64260 powerpc mpc824x bb3aef9 2014-04-18
MOUSSE powerpc mpc824x 03f2ecc 2014-04-18
diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h
deleted file mode 100644
index 46157ccc40..0000000000
--- a/include/configs/SIMPC8313.h
+++ /dev/null
@@ -1,580 +0,0 @@
-/*
- * Copyright (C) Sheldon Instruments, Inc. 2008
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-/*
- * simpc8313 board configuration file
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_NAND_U_BOOT
-
-#define CONFIG_E300 1
-#define CONFIG_MPC831x 1
-#define CONFIG_MPC8313 1
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
-
-#define CONFIG_SYS_TEXT_BASE 0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */
-#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
-
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
-#else
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#endif
-
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_ELBC 1
-
-#define CONFIG_MISC_INIT_R
-
-/*
- * On-board devices
- *
- * TSEC1 is Marvell PHY 88E1118
- */
-
-#define CONFIG_SYS_33MHZ
-
-#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
-
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-#define CONFIG_SYS_IMMR 0xE0000000
-
-#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR
-#endif
-
-#define CONFIG_SYS_MEMTEST_START 0x00001000
-#define CONFIG_SYS_MEMTEST_END 0x07f00000
-
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-
-/*
- * Device configurations
- */
-#define CONFIG_TSEC1
-
-/*
- * DDR Setup
- */
- /* DDR is system memory*/
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_MAX_MEM_MAPPED (512 << 20)
-
-#define CONFIG_SYS_DDRCDR (DDRCDR_EN \
- | DDRCDR_PZ_NOMZ \
- | DDRCDR_NZ_NOMZ \
- | DDRCDR_M_ODR)
- /* 0x73000002 TODO ODR & DRN ? */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_NO_FLASH
-
-#if !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-
-/*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
-#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
- | (0xFF << LBCR_BMT_SHIFT) \
- | 0xF) /* 0x0004ff0f */
-
- /* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-/* drivers/mtd/nand/nand.c */
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE 0xFFF00000
-#else
-#define CONFIG_SYS_NAND_BASE 0xE2800000
-#endif
-#define CONFIG_SYS_FPGA_BASE 0xFF000000
-
-#define CONFIG_CMD_NAND
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_NAND_FSL_ELBC 1
-
-#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
- | BR_DECC_CHK_GEN /* Use HW ECC */ \
- | BR_PS_8 /* 8 bit Port */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-
-#ifdef CONFIG_NAND_SP
-#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
-#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
- /* NAND chip block size */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10)
-#define NAND_CACHE_PAGES 32
-#elif defined(CONFIG_NAND_LP)
-#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB \
- | OR_FCM_PGS \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
-#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_256KB)
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048 /* NAND chip page size */
- /* NAND chip block size */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
-#define NAND_CACHE_PAGES 64
-#else
-#error Page size of NAND not defined.
-#endif /* CONFIG_NAND_SP */
-
-#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SYS_NAND_BLOCK_SIZE
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_NAND_BASE
-
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR0_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR0_PRELIM
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA_BASE \
- | BR_PS_16 \
- | BR_MS_UPMA \
- | BR_V)
-#define CONFIG_SYS_OR1_PRELIM (OR_AM_2MB \
- | OR_UPM_BCTLD)
-
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_2MB)
-
-/*
- * JFFS2 configuration
- */
-#define CONFIG_JFFS2_NAND
-#define CONFIG_JFFS2_DEV "nand0"
-
-/* mtdparts command line support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define MTDIDS_DEFAULT "nand0=nand0"
-#define MTDPARTS_DEFAULT "mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)"
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_NS16550_MIN_FUNCTIONS
-#endif
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
-#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-
-/*
- * TSEC
- */
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
-
-#define CONFIG_GMII /* MII PHY management */
-
-#ifdef CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define TSEC1_PHY_ADDR 0x0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC1_PHYIDX 0
-#endif
-
-#ifdef CONFIG_TSEC2
-#define CONFIG_HAS_ETH1
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define TSEC2_PHY_ADDR 4
-#define TSEC2_FLAGS TSEC_GIGABIT
-#define TSEC2_PHYIDX 0
-#endif
-
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME "TSEC1"
-
-/*
- * Configure on-board RTC
- */
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/*
- * Environment
- */
-#if defined(CONFIG_NAND_U_BOOT)
- #define CONFIG_ENV_IS_IN_NAND 1
- #define CONFIG_ENV_OFFSET (768 * 1024)
- #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
- #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
- #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
- #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4)
- #define CONFIG_ENV_OFFSET_REDUND \
- (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
-#elif !defined(CONFIG_SYS_RAMBOOT)
- #define CONFIG_ENV_IS_IN_FLASH 1
- #define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
- #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
- #define CONFIG_ENV_SIZE 0x2000
-
-/* Address and size of Redundant Environment Sector */
-#else
- #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_FLASH
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_JFFS2
-
-#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
- #undef CONFIG_CMD_SAVEENV
- #undef CONFIG_CMD_LOADS
-#endif
-
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- + sizeof(CONFIG_SYS_PROMPT) \
- + 16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
- /* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
- /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-
-#define CONFIG_SYS_HRCW_LOW (HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \
- | 0x20000000 /* reserved */ \
- | HRCWL_DDR_TO_SCB_CLK_2X1 \
- | HRCWL_CSB_TO_CLKIN_4X1 \
- | HRCWL_CORE_TO_CSB_2_5X1)
-
-#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 4)
-
-#define CONFIG_SYS_HRCW_HIGH_BASE (HRCWH_PCI_HOST \
- | HRCWH_PCI1_ARBITER_ENABLE \
- | HRCWH_CORE_ENABLE \
- | HRCWH_BOOTSEQ_DISABLE \
- | HRCWH_SW_WATCHDOG_DISABLE \
- | HRCWH_TSEC1M_IN_RGMII \
- | HRCWH_TSEC2M_IN_RGMII \
- | HRCWH_BIG_ENDIAN \
- | HRCWH_LALE_NORMAL)
-
-#ifdef CONFIG_NAND_LP
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \
- | HRCWH_FROM_0XFFF00100 \
- | HRCWH_ROM_LOC_NAND_LP_8BIT \
- | HRCWH_RL_EXT_NAND)
-#else
-#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \
- | HRCWH_FROM_0XFFF00100 \
- | HRCWH_ROM_LOC_NAND_SP_8BIT \
- | HRCWH_RL_EXT_NAND)
-#endif
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH (SICRH_ETSEC2_B \
- | SICRH_ETSEC2_C \
- | SICRH_ETSEC2_D \
- | SICRH_ETSEC2_E \
- | SICRH_ETSEC2_F \
- | SICRH_ETSEC2_G \
- | SICRH_TSOBI1 \
- | SICRH_TSOBI2)
-#define CONFIG_SYS_SICRL (SICRL_LBC \
- | SICRL_USBDR_10 \
- | SICRL_ETSEC2_A)
-
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
- | HID0_ENABLE_INSTRUCTION_CACHE \
- | HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-
-#define CONFIG_SYS_HID2 HID2_HBE
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT1L ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
- | BATL_PP_RW)
-#define CONFIG_SYS_IBAT1U ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* PCI @ 0x80000000 */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MEM_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MMIO_BASE \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* PCI2 not supported on 8313 */
-#define CONFIG_SYS_IBAT4L (0)
-#define CONFIG_SYS_IBAT4U (0)
-
-/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
- | BATL_PP_RW \
- | BATL_CACHEINHIBIT \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CONFIG_SYS_IBAT6L (0xF0000000 \
- | BATL_PP_RW \
- | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xF0000000 \
- | BATU_BL_256M \
- | BATU_VS \
- | BATU_VP)
-
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_NETDEV "eth1"
-
-#define CONFIG_HOSTNAME simpc8313
-#define CONFIG_ROOTPATH "/tftpboot/"
-#define CONFIG_BOOTFILE "/tftpboot/uImage"
- /* U-Boot image on TFTP server */
-#define CONFIG_UBOOTPATH "u-boot-nand.bin"
-#define CONFIG_FDTFILE "simpc8313.dtb"
-
- /* default location for tftp and bootm */
-#define CONFIG_LOADADDR 500000
-#define CONFIG_BOOTDELAY 5 /* 5 second delay */
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_BOOTCOMMAND "nand read $loadaddr kernel 600000;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=" CONFIG_NETDEV "\0" \
- "ethprime=TSEC1\0" \
- "uboot=" CONFIG_UBOOTPATH "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "erase " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize; " \
- "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
- " +$filesize; " \
- "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \
- " $filesize\0" \
- "fdtaddr=ae0000\0" \
- "fdtfile=" CONFIG_FDTFILE "\0" \
- "console=ttyS0\0" \
- "setbootargs=setenv bootargs " \
- "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
- "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
- "$netdev:off " \
- "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
- "load_uboot=tftp 100000 u-boot-nand.bin\0" \
- "burn_uboot=nand erase u-boot 80000; " \
- "nand write 100000 u-boot $filesize\0" \
- "update_uboot=run load_uboot;run burn_uboot\0" \
- "mtdids=nand0=nand0\0" \
- "mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
- "bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw " \
- "console=ttyS0,115200\0" \
- ""
-
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv rootdev /dev/nfs;" \
- "run setbootargs;" \
- "run setipargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv rootdev /dev/ram;" \
- "run setbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#endif /* __CONFIG_H */
diff --git a/nand_spl/board/sheldon/simpc8313/Makefile b/nand_spl/board/sheldon/simpc8313/Makefile
deleted file mode 100644
index 657f65fd22..0000000000
--- a/nand_spl/board/sheldon/simpc8313/Makefile
+++ /dev/null
@@ -1,81 +0,0 @@
-#
-# (C) Copyright 2007
-# Stefan Roese, DENX Software Engineering, sr@denx.de.
-# (C) Copyright 2008 Freescale Semiconductor
-# (C) Copyright Sheldon Instruments, Inc. 2008
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-include $(srctree)/$(src)/config.mk
-
-nandobj := $(objtree)/nand_spl/
-
-LDSCRIPT= $(srctree)/nand_spl/board/$(BOARDDIR)/u-boot.lds
-LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
- $(LDFLAGS) $(LDFLAGS_FINAL)
-asflags-y += -DCONFIG_NAND_SPL
-ccflags-y += -DCONFIG_NAND_SPL
-
-SOBJS = start.o ticks.o
-COBJS = nand_boot_fsl_elbc.o $(BOARD).o sdram.o ns16550.o spl_minimal.o \
- time.o cache.o
-
-OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS))
-__OBJS := $(SOBJS) $(COBJS)
-LNDIR := $(nandobj)board/$(BOARDDIR)
-
-targets += $(__OBJS)
-
-all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
-
-$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@
-
-$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@
-
-$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds
- cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
- -Map $(nandobj)u-boot-spl.map -o $@
-
-$(nandobj)u-boot.lds: $(LDSCRIPT)
- $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
-
-# create symbolic links for common files
-
-$(obj)/start.S:
- @rm -f $@
- ln -s $(srctree)/arch/powerpc/cpu/mpc83xx/start.S $@
-
-$(obj)/nand_boot_fsl_elbc.c:
- @rm -f $@
- ln -s $(srctree)/nand_spl/nand_boot_fsl_elbc.c $@
-
-$(obj)/sdram.c:
- @rm -f $@
- ln -s $(srctree)/board/$(BOARDDIR)/sdram.c $@
-
-$(obj)/$(BOARD).c:
- @rm -f $@
- ln -s $(srctree)/board/$(BOARDDIR)/$(BOARD).c $@
-
-$(obj)/ns16550.c:
- @rm -f $@
- ln -s $(srctree)/drivers/serial/ns16550.c $@
-
-$(obj)/spl_minimal.c:
- @rm -f $@
- ln -s $(srctree)/arch/powerpc/cpu/mpc83xx/spl_minimal.c $@
-
-$(obj)/cache.c:
- @rm -f $@
- ln -s $(srctree)/arch/powerpc/lib/cache.c $@
-
-$(obj)/time.c:
- @rm -f $@
- ln -s $(srctree)/arch/powerpc/lib/time.c $@
-
-$(obj)/ticks.S:
- @rm -f $@
- ln -s $(srctree)/arch/powerpc/lib/ticks.S $@
diff --git a/nand_spl/board/sheldon/simpc8313/config.mk b/nand_spl/board/sheldon/simpc8313/config.mk
deleted file mode 100644
index d1b4e2eeb6..0000000000
--- a/nand_spl/board/sheldon/simpc8313/config.mk
+++ /dev/null
@@ -1,5 +0,0 @@
-ifdef CONFIG_NAND_LP
-PAD_TO = 0xFFF20000
-else
-PAD_TO = 0xFFF04000
-endif
diff --git a/nand_spl/board/sheldon/simpc8313/u-boot.lds b/nand_spl/board/sheldon/simpc8313/u-boot.lds
deleted file mode 100644
index 4e4d511f9b..0000000000
--- a/nand_spl/board/sheldon/simpc8313/u-boot.lds
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Copyright 2008 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-SECTIONS
-{
- . = 0xfff00000;
- .text : {
- *(.text*)
- . = ALIGN(16);
- *(.eh_frame)
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- . = ALIGN(8);
- .data : {
- *(.data*)
- *(.sdata*)
- _GOT2_TABLE_ = .;
- *(.got2)
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
-
- . = ALIGN(8);
- __bss_start = .;
- .bss (NOLOAD) : { *(.*bss) }
- __bss_end = .;
-}
-ENTRY(_start)
-ASSERT(__bss_end <= 0xfff01000, "NAND bootstrap too big");
generated by cgit (git 2.34.1) at 2024-12-25 07:28:02 +0000