summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--README8
-rw-r--r--doc/README.LED58
-rw-r--r--drivers/led/Kconfig323
3 files changed, 355 insertions, 34 deletions
diff --git a/README b/README
index 7e0dd35f93..a95348a876 100644
--- a/README
+++ b/README
@@ -2033,7 +2033,7 @@ The following options need to be configured:
A byte containing the id of the VLAN.
-- Status LED: CONFIG_STATUS_LED
+- Status LED: CONFIG_LED_STATUS
Several configurations allow to display the current
status using a LED. For instance, the LED will blink
@@ -2041,15 +2041,15 @@ The following options need to be configured:
soon as a reply to a BOOTP request was received, and
start blinking slow once the Linux kernel is running
(supported by a status LED driver in the Linux
- kernel). Defining CONFIG_STATUS_LED enables this
+ kernel). Defining CONFIG_LED_STATUS enables this
feature in U-Boot.
Additional options:
- CONFIG_GPIO_LED
+ CONFIG_LED_STATUS_GPIO
The status LED can be connected to a GPIO pin.
In such cases, the gpio_led driver can be used as a
- status LED backend implementation. Define CONFIG_GPIO_LED
+ status LED backend implementation. Define CONFIG_LED_STATUS_GPIO
to include the gpio_led driver in the U-Boot binary.
CONFIG_GPIO_LED_INVERTED_TABLE
diff --git a/doc/README.LED b/doc/README.LED
index c3bcb3ac80..7aa95bddf7 100644
--- a/doc/README.LED
+++ b/doc/README.LED
@@ -5,48 +5,48 @@ This README describes the status LED API.
The API is defined by the include file include/status_led.h
-The first step is to define CONFIG_STATUS_LED in the board config file.
+The first step is to enable CONFIG_LED_STATUS in menuconfig:
+> Device Drivers > LED Support.
-If the LED support is only for a single board, define CONFIG_BOARD_SPECIFIC_LED
-in the board config file.
+If the LED support is only for specific board, enable
+CONFIG_LED_STATUS_BOARD_SPECIFIC in the menuconfig.
-At a minimum, these macros must be defined at
-STATUS_LED_BIT
-STATUS_LED_STATE
-STATUS_LED_PERIOD
+Status LEDS 0 to 5 are enabled by the following configurations at menuconfig:
+CONFIG_STATUS_LED0, CONFIG_STATUS_LED1, ... CONFIG_STATUS_LED5
-If there are multiple status LED's define
-STATUS_LED_BIT<n>
-STATUS_LED_STATE<n>
-STATUS_LED_PERIOD<n>
+The following should be configured for each of the enabled LEDs:
+CONFIG_STATUS_LED_BIT<n>
+CONFIG_STATUS_LED_STATE<n>
+CONFIG_STATUS_LED_FREQ<n>
+Where <n> is an integer 1 through 5 (empty for 0).
-Where <n> can a integer 1 through 3.
-
-STATUS_LED_BIT is passed into the __led_* functions to identify which LED is
-being acted on. As such, the value choose must be unique with with respect to
-the other STATUS_LED_BIT's. Mapping the value to a physical LED is the
+CONFIG_STATUS_LED_BIT is passed into the __led_* functions to identify which LED
+is being acted on. As such, the value choose must be unique with with respect to
+the other CONFIG_STATUS_LED_BIT's. Mapping the value to a physical LED is the
reponsiblity of the __led_* function.
-STATUS_LED_STATE is the initial state of the LED. It should be set to one of
-these values: STATUS_LED_OFF or STATUS_LED_ON.
+CONFIG_STATUS_LED_STATE is the initial state of the LED. It should be set to one
+of these values: CONFIG_LED_STATUS_OFF or CONFIG_LED_STATUS_ON.
-STATUS_LED_PERIOD is how long is the LED blink period. This usually set to
-(CONFIG_SYS_HZ / <N>) where <N> is the frequency of the blink. Typical values
-range from 2 to 10.
+CONFIG_STATUS_LED_FREQ determines the LED blink frequency.
+Values range from 2 to 10.
Some other LED macros
+---------------------
-STATUS_LED_BOOT is the LED to light when the board is booting. This must be a
-valid STATUS_LED_BIT value.
+CONFIG_STATUS_LED_BOOT is the LED to light when the board is booting.
+This must be a valid LED number (0-5).
-STATUS_LED_RED is the red LED. It is used signal errors. This must be a valid
-STATUS_LED_BIT value. Other similar color LED's are STATUS_LED_YELLOW and
-STATUS_LED_BLUE.
+CONFIG_STATUS_LED_RED is the red LED. It is used to signal errors. This must be
+a valid LED number (0-5). Other similar color LED's macros are
+CONFIG_STATUS_LED_GREEN, CONFIG_STATUS_LED_YELLOW and CONFIG_STATUS_LED_BLUE.
-These board must define these functions
+General LED functions
+---------------------
+The following functions should be defined:
-__led_init is called once to initialize the LED to STATUS_LED_STATE. One time
-start up code should be placed here.
+__led_init is called once to initialize the LED to CONFIG_STATUS_LED_STATE.
+One time start up code should be placed here.
__led_set is called to change the state of the LED.
diff --git a/drivers/led/Kconfig b/drivers/led/Kconfig
index fe74403460..609b1fa3fe 100644
--- a/drivers/led/Kconfig
+++ b/drivers/led/Kconfig
@@ -17,7 +17,6 @@ config SPL_LED
If this is acceptable and you have a need to use LEDs in SPL,
enable this option. You will need to enable device tree in SPL
for this to work.
-
config LED_GPIO
bool "LED support for GPIO-connected LEDs"
depends on LED && DM_GPIO
@@ -34,4 +33,326 @@ config SPL_LED_GPIO
This option is an SPL-variant of the LED_GPIO option.
See the help of LED_GPIO for details.
+config LED_STATUS
+ bool "Enable status LED API"
+ help
+ Allows common u-boot commands to use a board's leds to
+ provide status for activities like booting and downloading files.
+
+if LED_STATUS
+
+# Hidden constants
+
+config LED_STATUS_OFF
+ int
+ default 0
+
+config LED_STATUS_BLINKING
+ int
+ default 1
+
+config LED_STATUS_ON
+ int
+ default 2
+
+# Hidden constants end
+
+config LED_STATUS_GPIO
+ bool "GPIO status LED implementation"
+ help
+ The status LED can be connected to a GPIO pin. In such cases, the
+ gpio_led driver can be used as a status LED backend implementation.
+
+config LED_STATUS_BOARD_SPECIFIC
+ bool "Specific board"
+ default y
+ help
+ LED support is only for a specific board.
+
+comment "LEDs parameters"
+
+config LED_STATUS0
+ bool "Enable status LED 0"
+
+if LED_STATUS0
+
+config LED_STATUS_BIT
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT is passed into the __led_* functions to identify
+ which LED is being acted on. As such, the chosen value must be unique
+ with respect to the other CONFIG_LED_STATUS_BIT's. Mapping the value
+ to a physical LED is the responsibility of the __led_* function.
+
+config LED_STATUS_STATE
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ:
+ LED_STATUS_PERIOD = CONFIG_SYS_HZ/LED_STATUS_FREQ
+ Values range: 2 - 10
+
+endif # LED_STATUS0
+
+config LED_STATUS1
+ bool "Enable status LED 1"
+
+if LED_STATUS1
+
+config LED_STATUS_BIT1
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT1 is passed into the __led_* functions to
+ identify which LED is being acted on. As such, the chosen value must
+ be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
+ the value to a physical LED is the responsibility of the __led_*
+ function.
+
+config LED_STATUS_STATE1
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ1
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ1:
+ LED_STATUS_PERIOD1 = CONFIG_SYS_HZ/LED_STATUS_FREQ1
+ Values range: 2 - 10
+
+endif # LED_STATUS1
+
+config LED_STATUS2
+ bool "Enable status LED 2"
+
+if LED_STATUS2
+
+config LED_STATUS_BIT2
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT2 is passed into the __led_* functions to
+ identify which LED is being acted on. As such, the chosen value must
+ be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
+ the value to a physical LED is the responsibility of the __led_*
+ function.
+
+config LED_STATUS_STATE2
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ2
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ2:
+ LED_STATUS_PERIOD2 = CONFIG_SYS_HZ/LED_STATUS_FREQ2
+ Values range: 2 - 10
+
+endif # LED_STATUS2
+
+config LED_STATUS3
+ bool "Enable status LED 3"
+
+if LED_STATUS3
+
+config LED_STATUS_BIT3
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT3 is passed into the __led_* functions to
+ identify which LED is being acted on. As such, the chosen value must
+ be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
+ the value to a physical LED is the responsibility of the __led_*
+ function.
+
+config LED_STATUS_STATE3
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ3
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ3:
+ LED_STATUS_PERIOD3 = CONFIG_SYS_HZ/LED_STATUS_FREQ3
+ Values range: 2 - 10
+
+endif # LED_STATUS3
+
+config LED_STATUS4
+ bool "Enable status LED 4"
+
+if LED_STATUS4
+
+config LED_STATUS_BIT4
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT4 is passed into the __led_* functions to
+ identify which LED is being acted on. As such, the chosen value must
+ be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
+ the value to a physical LED is the responsibility of the __led_*
+ function.
+
+config LED_STATUS_STATE4
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ4
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ4:
+ LED_STATUS_PERIOD4 = CONFIG_SYS_HZ/LED_STATUS_FREQ4
+ Values range: 2 - 10
+
+endif # LED_STATUS4
+
+config LED_STATUS5
+ bool "Enable status LED 5"
+
+if LED_STATUS5
+
+config LED_STATUS_BIT5
+ int "identification"
+ help
+ CONFIG_LED_STATUS_BIT5 is passed into the __led_* functions to
+ identify which LED is being acted on. As such, the chosen value must
+ be unique with respect to the other CONFIG_LED_STATUS_BIT's. Mapping
+ the value to a physical LED is the responsibility of the __led_*
+ function.
+
+config LED_STATUS_STATE5
+ int "initial state"
+ range LED_STATUS_OFF LED_STATUS_ON
+ default LED_STATUS_OFF
+ help
+ Should be set one of the following:
+ 0 - off
+ 1 - blinking
+ 2 - on
+
+config LED_STATUS_FREQ5
+ int "blink frequency"
+ range 2 10
+ default 2
+ help
+ The LED blink period calculated from LED_STATUS_FREQ5:
+ LED_STATUS_PERIOD5 = CONFIG_SYS_HZ/LED_STATUS_FREQ5
+ Values range: 2 - 10
+
+endif # LED_STATUS5
+
+config LED_STATUS_BOOT_ENABLE
+ bool "Enable BOOT LED"
+ help
+ Enable to turn an LED on when the board is booting.
+
+if LED_STATUS_BOOT_ENABLE
+
+config LED_STATUS_BOOT
+ int "LED to light when the board is booting"
+ help
+ Valid enabled LED device number.
+
+endif # LED_STATUS_BOOT_ENABLE
+
+config LED_STATUS_RED_ENABLE
+ bool "Enable red LED"
+ help
+ Enable red status LED.
+
+if LED_STATUS_RED_ENABLE
+
+config LED_STATUS_RED
+ int "Red LED identification"
+ help
+ Valid enabled LED device number.
+
+endif # LED_STATUS_RED_ENABLE
+
+config LED_STATUS_YELLOW_ENABLE
+ bool "Enable yellow LED"
+ help
+ Enable yellow status LED.
+
+if LED_STATUS_YELLOW_ENABLE
+
+config LED_STATUS_YELLOW
+ int "Yellow LED identification"
+ help
+ Valid enabled LED device number.
+
+endif # LED_STATUS_YELLOW_ENABLE
+
+config LED_STATUS_BLUE_ENABLE
+ bool "Enable blue LED"
+ help
+ Enable blue status LED.
+
+if LED_STATUS_BLUE_ENABLE
+
+config LED_STATUS_BLUE
+ int "Blue LED identification"
+ help
+ Valid enabled LED device number.
+
+endif # LED_STATUS_BLUE_ENABLE
+
+config LED_STATUS_GREEN_ENABLE
+ bool "Enable green LED"
+ help
+ Enable green status LED.
+
+if LED_STATUS_GREEN_ENABLE
+
+config LED_STATUS_GREEN
+ int "Green LED identification"
+ help
+ Valid enabled LED device number (0-5).
+
+endif # LED_STATUS_GREEN_ENABLE
+
+config LED_STATUS_CMD
+ bool "Enable status LED commands"
+
+endif # LED_STATUS
+
endmenu