summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/dts/Makefile1
-rw-r--r--arch/arm/dts/armada-388-helios4.dts314
-rw-r--r--arch/arm/dts/armada-38x-solidrun-microsom.dtsi101
-rw-r--r--arch/arm/mach-mvebu/Kconfig7
-rw-r--r--board/kobol/helios4/MAINTAINERS6
-rw-r--r--board/kobol/helios4/Makefile5
-rw-r--r--board/kobol/helios4/README46
-rw-r--r--board/kobol/helios4/helios4.c163
-rw-r--r--board/kobol/helios4/kwbimage.cfg13
-rw-r--r--configs/helios4_defconfig58
-rw-r--r--include/configs/helios4.h172
11 files changed, 886 insertions, 0 deletions
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 790571b773..3dcd6dd7a8 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -91,6 +91,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
armada-375-db.dtb \
armada-388-clearfog.dtb \
armada-388-gp.dtb \
+ armada-388-helios4.dtb \
armada-385-amc.dtb \
armada-7040-db.dtb \
armada-7040-db-nand.dtb \
diff --git a/arch/arm/dts/armada-388-helios4.dts b/arch/arm/dts/armada-388-helios4.dts
new file mode 100644
index 0000000000..049d322964
--- /dev/null
+++ b/arch/arm/dts/armada-388-helios4.dts
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Helios4
+ * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ * Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io>
+ *
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+ model = "Helios4";
+ compatible = "kobol,helios4", "marvell,armada388",
+ "marvell,armada385", "marvell,armada380";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2 GB */
+ };
+
+ aliases {
+ /* So that mvebu u-boot can update the MAC addresses */
+ ethernet1 = &eth0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_12v: regulator-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "power_brick_12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&reg_12v>;
+ };
+
+ reg_5p0v_hdd: regulator-5v-hdd {
+ compatible = "regulator-fixed";
+ regulator-name = "5V_HDD";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_12v>;
+ };
+
+ reg_5p0v_usb: regulator-5v-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "USB-PWR";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ enable-active-high;
+ gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&reg_12v>;
+ };
+
+ system-leds {
+ compatible = "gpio-leds";
+ status-led {
+ label = "helios4:green:status";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ default-state = "on";
+ };
+
+ fault-led {
+ label = "helios4:red:fault";
+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ };
+
+ io-leds {
+ compatible = "gpio-leds";
+ sata1-led {
+ label = "helios4:green:ata1";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata1";
+ default-state = "off";
+ };
+ sata2-led {
+ label = "helios4:green:ata2";
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata2";
+ default-state = "off";
+ };
+ sata3-led {
+ label = "helios4:green:ata3";
+ gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata3";
+ default-state = "off";
+ };
+ sata4-led {
+ label = "helios4:green:ata4";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata4";
+ default-state = "off";
+ };
+ usb-led {
+ label = "helios4:green:usb";
+ gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "usb-host";
+ default-state = "off";
+ };
+ };
+
+ fan1: j10-pwm {
+ compatible = "pwm-fan";
+ pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */
+ };
+
+ fan2: j17-pwm {
+ compatible = "pwm-fan";
+ pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */
+ };
+
+ usb2_phy: usb2-phy {
+ compatible = "usb-nop-xceiv";
+ vbus-regulator = <&reg_5p0v_usb>;
+ };
+
+ usb3_phy: usb3-phy {
+ compatible = "usb-nop-xceiv";
+ };
+
+ soc {
+ internal-regs {
+ i2c@11000 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /*
+ * PCA9655 GPIO expander, up to 1MHz clock.
+ * 0-Board Revision bit 0 #
+ * 1-Board Revision bit 1 #
+ * 5-USB3 overcurrent
+ * 6-USB3 power
+ */
+ expander0: gpio-expander@20 {
+ /*
+ * This is how it should be:
+ * compatible = "onnn,pca9655",
+ * "nxp,pca9555";
+ * but you can't do this because of
+ * the way I2C works.
+ */
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pca0_pins>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ board_rev_bit_0 {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "board-rev-0";
+ };
+ board_rev_bit_1 {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "board-rev-1";
+ };
+ usb3_ilimit {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name =
+ "usb-overcurrent-status";
+ };
+ };
+
+ temp_sensor: temp@4c {
+ compatible = "ti,lm75";
+ reg = <0x4c>;
+ vcc-supply = <&reg_3p3v>;
+ };
+ };
+
+ i2c@11100 {
+ /*
+ * External I2C Bus for user peripheral
+ */
+ clock-frequency = <400000>;
+ pinctrl-0 = <&helios_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sata@a8000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata0: sata-port@0 {
+ reg = <0>;
+ };
+
+ sata1: sata-port@1 {
+ reg = <1>;
+ };
+ };
+
+ sata@e0000 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata2: sata-port@0 {
+ reg = <0>;
+ };
+
+ sata3: sata-port@1 {
+ reg = <1>;
+ };
+ };
+
+ spi@10680 {
+ pinctrl-0 = <&spi1_pins
+ &microsom_spi1_cs_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sdhci@d8000 {
+ bus-width = <4>;
+ cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-0 = <&helios_sdhci_pins
+ &helios_sdhci_cd_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ vmmc = <&reg_3p3v>;
+ wp-inverted;
+ };
+
+ usb@58000 {
+ usb-phy = <&usb2_phy>;
+ status = "okay";
+ };
+
+ usb3@f0000 {
+ status = "okay";
+ };
+
+ usb3@f8000 {
+ status = "okay";
+ };
+
+ pinctrl@18000 {
+ pca0_pins: pca0-pins {
+ marvell,pins = "mpp23";
+ marvell,function = "gpio";
+ };
+ microsom_phy0_int_pins: microsom-phy0-int-pins {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+ helios_i2c1_pins: i2c1-pins {
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c1";
+ };
+ helios_sdhci_cd_pins: helios-sdhci-cd-pins {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+ helios_sdhci_pins: helios-sdhci-pins {
+ marvell,pins = "mpp21", "mpp28",
+ "mpp37", "mpp38",
+ "mpp39", "mpp40";
+ marvell,function = "sd0";
+ };
+ helios_led_pins: helios-led-pins {
+ marvell,pins = "mpp24", "mpp25",
+ "mpp49", "mpp50",
+ "mpp52", "mpp53",
+ "mpp54";
+ marvell,function = "gpio";
+ };
+ helios_fan_pins: helios-fan-pins {
+ marvell,pins = "mpp41", "mpp43",
+ "mpp48", "mpp55";
+ marvell,function = "gpio";
+ };
+ microsom_spi1_cs_pins: spi1-cs-pins {
+ marvell,pins = "mpp59";
+ marvell,function = "spi1";
+ };
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
new file mode 100644
index 0000000000..a2627223ce
--- /dev/null
+++ b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for SolidRun Armada 38x Microsom
+ *
+ * Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board. Things will change, don't expect this file to
+ * remain compatible info the future.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>; /* 256 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+ internal-regs {
+ rtc@a3800 {
+ /*
+ * If the rtc doesn't work, run "date reset"
+ * twice in u-boot.
+ */
+ status = "okay";
+ };
+ };
+ };
+};
+
+&eth0 {
+ /* ethernet@70000 */
+ mac-address = [00 50 43 02 02 01];
+ pinctrl-0 = <&ge0_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy_dedicated>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&mdio {
+ /*
+ * Add the phy clock here, so the phy can be accessed to read its
+ * IDs prior to binding with the driver.
+ */
+ pinctrl-0 = <&mdio_pins &microsom_phy_clk_pins>;
+ pinctrl-names = "default";
+
+ phy_dedicated: ethernet-phy@0 {
+ /*
+ * Annoyingly, the marvell phy driver configures the LED
+ * register, rather than preserving reset-loaded setting.
+ * We undo that rubbish here.
+ */
+ marvell,reg-init = <3 16 0 0x101e>;
+ reg = <0>;
+ };
+};
+
+&pinctrl {
+ microsom_phy_clk_pins: microsom-phy-clk-pins {
+ marvell,pins = "mpp45";
+ marvell,function = "ref";
+ };
+ /* Optional eMMC */
+ microsom_sdhci_pins: microsom-sdhci-pins {
+ marvell,pins = "mpp21", "mpp28", "mpp37",
+ "mpp38", "mpp39", "mpp40";
+ marvell,function = "sd0";
+ };
+};
+
+&spi1 {
+ /* The microsom has an optional W25Q32 on board, connected to CS0 */
+ pinctrl-0 = <&spi1_pins>;
+
+ w25q32: spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q32", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <3000000>;
+ status = "disabled";
+ };
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index f431cff950..5415b5a7bf 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -75,6 +75,10 @@ config TARGET_CLEARFOG
bool "Support ClearFog"
select 88F6820
+config TARGET_HELIOS4
+ bool "Support Helios4"
+ select 88F6820
+
config TARGET_MVEBU_ARMADA_37XX
bool "Support Armada 37xx platforms"
select ARMADA_3700
@@ -132,6 +136,7 @@ endchoice
config SYS_BOARD
default "clearfog" if TARGET_CLEARFOG
+ default "helios4" if TARGET_HELIOS4
default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
default "db-88f6720" if TARGET_DB_88F6720
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
@@ -146,6 +151,7 @@ config SYS_BOARD
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
+ default "helios4" if TARGET_HELIOS4
default "mvebu_armada-37xx" if TARGET_MVEBU_ARMADA_37XX
default "db-88f6720" if TARGET_DB_88F6720
default "db-88f6820-gp" if TARGET_DB_88F6820_GP
@@ -166,6 +172,7 @@ config SYS_VENDOR
default "Marvell" if TARGET_DB_88F6820_AMC
default "Marvell" if TARGET_MVEBU_ARMADA_8K
default "solidrun" if TARGET_CLEARFOG
+ default "kobol" if TARGET_HELIOS4
default "Synology" if TARGET_DS414
default "CZ.NIC" if TARGET_TURRIS_OMNIA
default "CZ.NIC" if TARGET_TURRIS_MOX
diff --git a/board/kobol/helios4/MAINTAINERS b/board/kobol/helios4/MAINTAINERS
new file mode 100644
index 0000000000..c9610deee7
--- /dev/null
+++ b/board/kobol/helios4/MAINTAINERS
@@ -0,0 +1,6 @@
+HELIOS4 BOARD
+M: Dennis Gilmore <dgilmore@redhat.com>
+S: Maintained
+F: board/kobol/helios4/
+F: include/configs/helios4.h
+F: configs/helios4_defconfig
diff --git a/board/kobol/helios4/Makefile b/board/kobol/helios4/Makefile
new file mode 100644
index 0000000000..63f0796397
--- /dev/null
+++ b/board/kobol/helios4/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+
+obj-y := helios4.o
diff --git a/board/kobol/helios4/README b/board/kobol/helios4/README
new file mode 100644
index 0000000000..749f048278
--- /dev/null
+++ b/board/kobol/helios4/README
@@ -0,0 +1,46 @@
+Update from original Marvell U-Boot to mainline U-Boot:
+-------------------------------------------------------
+
+Generate the U-Boot image with these commands:
+
+$ make helios4_defconfig
+$ make
+
+The resulting image including the SPL binary with the
+full DDR setup is "u-boot-spl.kwb".
+
+Now all you need to do is copy this image on a SD card.
+For example with this command:
+
+$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
+
+Please use the correct device node for your setup instead
+of "/dev/sdX" here!
+
+Boot selection:
+---------------
+
+Before powering up the board, boot selection should be done via the SW1 dip
+switch (0: OFF, 1: ON):
+
+ - SPI: 00010
+ - SD/eMMC: 00111
+ - SATA1: 11100
+ - UART: 11110
+
+Boot from UART:
+---------------
+
+Connect the on-board micro-USB (CF Pro: CON11, CF Base: CON5)
+to your host.
+
+Set the SW1 DIP switches to UART boot (see above).
+
+Run the following command to initiate U-Boot download:
+
+ ./tools/kwboot -p -b u-boot-spl.kwb /dev/ttyUSBX
+
+Use the correct UART device node for /dev/ttyUSBX.
+
+When download finishes start your favorite terminal emulator
+on /dev/ttyUSBX.
diff --git a/board/kobol/helios4/helios4.c b/board/kobol/helios4/helios4.c
new file mode 100644
index 0000000000..341678319a
--- /dev/null
+++ b/board/kobol/helios4/helios4.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+ * based on board/solidrun/clearfog/clearfog.c
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ETH_PHY_CTRL_REG 0
+#define ETH_PHY_CTRL_POWER_DOWN_BIT 11
+#define ETH_PHY_CTRL_POWER_DOWN_MASK BIT(ETH_PHY_CTRL_POWER_DOWN_BIT)
+
+/*
+ * Those values and defines are taken from the Marvell U-Boot version
+ * "u-boot-2013.01-15t1-helios4" as well as the upstream config for clearfog
+ */
+#define BOARD_GPP_OUT_ENA_LOW 0xffffffff
+#define BOARD_GPP_OUT_ENA_MID 0xffffffff
+
+#define BOARD_GPP_OUT_VAL_LOW 0x0
+#define BOARD_GPP_OUT_VAL_MID 0x0
+#define BOARD_GPP_POL_LOW 0x0
+#define BOARD_GPP_POL_MID 0x0
+
+/* IO expander on Marvell GP board includes e.g. fan enabling */
+struct marvell_io_exp {
+ u8 addr;
+ u8 val;
+};
+
+static struct marvell_io_exp io_exp[] = {
+ {6, 0xf9},
+ {2, 0x46}, /* Assert reset signals and enable USB3 current limiter */
+ {6, 0xb9}
+};
+
+static struct serdes_map board_serdes_map[] = {
+ {SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {SATA1, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {SATA3, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {SATA2, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+ {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+ *serdes_map_array = board_serdes_map;
+ *count = ARRAY_SIZE(board_serdes_map);
+ return 0;
+}
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+ DEBUG_LEVEL_ERROR,
+ 0x1, /* active interfaces */
+ /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+ { { { {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0},
+ {0x1, 0, 0, 0} },
+ SPEED_BIN_DDR_1600K, /* speed_bin */
+ MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
+ MV_DDR_DIE_CAP_8GBIT, /* mem_size */
+ DDR_FREQ_800, /* frequency */
+ 0, 0, /* cas_wl cas_l */
+ MV_DDR_TEMP_LOW, /* temperature */
+ MV_DDR_TIM_DEFAULT} }, /* timing */
+ BUS_MASK_32BIT_ECC, /* Busses mask */
+ MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
+ { {0} }, /* raw spd data */
+ {0} /* timing parameters */
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+ /* Return the board topology as defined in the board code */
+ return &board_topology_map;
+}
+
+int board_early_init_f(void)
+{
+ /* Configure MPP */
+ writel(0x11111111, MVEBU_MPP_BASE + 0x00);
+ writel(0x11111111, MVEBU_MPP_BASE + 0x04);
+ writel(0x10400011, MVEBU_MPP_BASE + 0x08);
+ writel(0x22043333, MVEBU_MPP_BASE + 0x0c);
+ writel(0x44400002, MVEBU_MPP_BASE + 0x10);
+ writel(0x41144004, MVEBU_MPP_BASE + 0x14);
+ writel(0x40333333, MVEBU_MPP_BASE + 0x18);
+ writel(0x00004444, MVEBU_MPP_BASE + 0x1c);
+
+ /* Set GPP Out value */
+ writel(BOARD_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+ writel(BOARD_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+ /* Set GPP Polarity */
+ writel(BOARD_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+ writel(BOARD_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+ /* Set GPP Out Enable */
+ writel(BOARD_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+ writel(BOARD_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ int i;
+
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ /* Init I2C IO expanders */
+ for (i = 0; i < ARRAY_SIZE(io_exp); i++) {
+ struct udevice *dev;
+ int ret;
+
+ ret = i2c_get_chip_for_busnum(0, io_exp[i].addr, 1, &dev);
+ if (ret) {
+ printf("Cannot find I2C: %d\n", ret);
+ return 0;
+ }
+
+ ret = dm_i2c_write(dev, io_exp[i].val, &io_exp[i].val, 1);
+ if (ret) {
+ printf("Failed to set IO expander via I2C\n");
+ return -EIO;
+ }
+ }
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: Helios4\n");
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ cpu_eth_init(bis); /* Built in controller(s) come first */
+ return pci_eth_init(bis);
+}
diff --git a/board/kobol/helios4/kwbimage.cfg b/board/kobol/helios4/kwbimage.cfg
new file mode 100644
index 0000000000..035063bc90
--- /dev/null
+++ b/board/kobol/helios4/kwbimage.cfg
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2015 Stefan Roese <sr@denx.de>
+#
+
+# Armada 38x use version 1 image format
+VERSION 1
+
+# Boot Media configurations
+BOOT_FROM sdio
+
+# Binary Header (bin_hdr) with DDR3 training code
+BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig
new file mode 100644
index 0000000000..b72428555d
--- /dev/null
+++ b/configs/helios4_defconfig
@@ -0,0 +1,58 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x00800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_HELIOS4=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_DEFAULT_DEVICE_TREE="armada-388-helios4"
+CONFIG_DEBUG_UART=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_BOOTDELAY=3
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x141
+CONFIG_SPL_I2C_SUPPORT=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+# CONFIG_SPL_PARTITION_UUIDS is not set
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_MV=y
+CONFIG_AHCI=y
+CONFIG_SCSI_AHCI=y
+CONFIG_SCSI=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_BAR=y
+CONFIG_SPI_FLASH_WINBOND=y
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHY_GIGE=y
+CONFIG_MVNETA=y
+CONFIG_PCI=y
+CONFIG_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_I2C=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_STORAGE=y
diff --git a/include/configs/helios4.h b/include/configs/helios4.h
new file mode 100644
index 0000000000..ce912ea324
--- /dev/null
+++ b/include/configs/helios4.h
@@ -0,0 +1,172 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Dennis Gilmore <dgilmore@redhat.com>
+ */
+
+#ifndef _CONFIG_HELIOS4_H
+#define _CONFIG_HELIOS4_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+
+/*
+ * TEXT_BASE needs to be below 16MiB, since this area is scrubbed
+ * for DDR ECC byte filling in the SPL before loading the main
+ * U-Boot into it.
+ */
+#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+
+/*
+ * Commands configuration
+ */
+
+/* SPI NOR flash default params, used by sf commands */
+#define CONFIG_SF_DEFAULT_BUS 1
+
+/*
+ * SDIO/MMC Card Configuration
+ */
+#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE
+
+/* USB/EHCI configuration */
+#define CONFIG_EHCI_IS_TDI
+
+#define CONFIG_ENV_MIN_ENTRIES 128
+
+/*
+ * SATA/SCSI/AHCI configuration
+ */
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2
+#define CONFIG_SYS_SCSI_MAX_LUN 2
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+
+/* Environment in MMC */
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SECT_SIZE 0x200
+#define CONFIG_ENV_SIZE 0x10000
+/*
+ * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC
+ * boot image starts @ LBA-0.
+ * As result in MMC/eMMC case it will be a 1 sector gap between u-boot
+ * image and environment
+ */
+#define CONFIG_ENV_OFFSET 0xf0000
+#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET
+
+#define CONFIG_PHY_MARVELL /* there is a marvell phy */
+#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
+
+/* PCIe support */
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PCI_MVEBU
+#define CONFIG_PCI_SCAN_SHOW
+#endif
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define RELOCATION_LIMITS_ENV_SETTINGS \
+ "fdt_high=0x10000000\0" \
+ "initrd_high=0x10000000\0"
+
+/* SPL */
+/*
+ * Select the boot device here
+ *
+ * Currently supported are:
+ * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
+ * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
+ */
+#define SPL_BOOT_SPI_NOR_FLASH 1
+#define SPL_BOOT_SDIO_MMC_CARD 2
+#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD
+
+/* Defines for SPL */
+#define CONFIG_SPL_SIZE (140 << 10)
+#define CONFIG_SPL_TEXT_BASE 0x40000030
+#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
+
+#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MALLOC_SIMPLE
+#endif
+
+#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
+#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
+/* SPL related SPI defines */
+#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
+#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
+#endif
+
+#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
+/* SPL related MMC defines */
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
+#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
+#endif
+#endif
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/* Include the common distro boot environment */
+#ifndef CONFIG_SPL_BUILD
+
+#ifdef CONFIG_MMC
+#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
+#else
+#define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#ifdef CONFIG_USB_STORAGE
+#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#ifdef CONFIG_SATA
+#define BOOT_TARGET_DEVICES_SATA(func) func(SATA, sata, 0)
+#else
+#define BOOT_TARGET_DEVICES_SATA(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func) \
+ BOOT_TARGET_DEVICES_MMC(func) \
+ BOOT_TARGET_DEVICES_USB(func) \
+ BOOT_TARGET_DEVICES_SATA(func) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+
+#define KERNEL_ADDR_R __stringify(0x800000)
+#define FDT_ADDR_R __stringify(0x100000)
+#define RAMDISK_ADDR_R __stringify(0x1800000)
+#define SCRIPT_ADDR_R __stringify(0x200000)
+#define PXEFILE_ADDR_R __stringify(0x300000)
+
+#define LOAD_ADDRESS_ENV_SETTINGS \
+ "kernel_addr_r=" KERNEL_ADDR_R "\0" \
+ "fdt_addr_r=" FDT_ADDR_R "\0" \
+ "ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
+ "scriptaddr=" SCRIPT_ADDR_R "\0" \
+ "pxefile_addr_r=" PXEFILE_ADDR_R "\0"
+
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ RELOCATION_LIMITS_ENV_SETTINGS \
+ LOAD_ADDRESS_ENV_SETTINGS \
+ "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+ "console=ttyS0,115200\0" \
+ BOOTENV
+
+#endif /* CONFIG_SPL_BUILD */
+
+#endif /* _CONFIG_HELIOS4_H */