diff options
| -rw-r--r-- | board/sunxi/README.pine64 | 98 | ||||
| -rw-r--r-- | board/sunxi/README.sunxi64 | 165 |
2 files changed, 165 insertions, 98 deletions
diff --git a/board/sunxi/README.pine64 b/board/sunxi/README.pine64 deleted file mode 100644 index 5553415270..0000000000 --- a/board/sunxi/README.pine64 +++ /dev/null @@ -1,98 +0,0 @@ -Pine64 board README -==================== - -The Pine64(+) is a single board computer equipped with an AArch64 capable ARMv8 -compliant Allwinner A64 SoC. -This chip has ARM Cortex A-53 cores and thus can run both in AArch32 -(compatible to 32-bit ARMv7) and AArch64 modes. Upon reset the SoC starts -in AArch32 mode and executes 32-bit code from the Boot ROM (BROM). -This has some implications on U-Boot. - -Quick start -============ -- Get hold of a boot0.img file (see below for more details). -- Get the boot0img tool source from the tools directory in [1] and compile - that on your host. -- Build U-Boot: -$ export CROSS_COMPILE=aarch64-linux-gnu- -$ make pine64_plus_defconfig -$ make -- You also need a compiled ARM Trusted Firmware (ATF) binary. Checkout the - "allwinner" branch from the github repository [2] and build it: -$ export CROSS_COMPILE=aarch64-linux-gnu- -$ make PLAT=sun50iw1p1 DEBUG=1 bl31 - The resulting binary is build/sun50iw1p1/debug/bl31.bin. - -Now put an empty (or disposable) micro SD card in your card reader and learn -its device file name, replacing /dev/sd<x> below with the result (that could -be /dev/mmcblk<x> as well): - -$ ./boot0img --device /dev/sd<x> -e -u u-boot.bin -B boot0.img \ - -d trampoline64:0x44000 -s bl31.bin -a 0x44008 -p 100 -(either copying the respective files to the working directory or specifying -the paths directly) - -This will create a new partition table (with a 100 MB FAT boot partition), -copies boot0.img, ATF and U-Boot to the proper locations on the SD card and -will fill in the magic Allwinner header to be recognized by boot0. -Prefix the above call with "sudo" if you don't have write access to the -uSD card. You can also use "-o output.img" instead of "--device /dev/sd<x>" -to create an image file and "dd" that to the uSD card. -Omitting the "-p" option will skip the partition table. - -Now put this uSD card in the board and power it on. You should be greeted by -the U-Boot prompt. - - -Main U-Boot -============ -The main U-Boot proper is a real 64-bit ARMv8 port and runs entirely in the -64-bit AArch64 mode. It can load any AArch64 code, EFI applications or arm64 -Linux kernel images (often named "Image") using the booti command. -Launching 32-bit code and kernels is technically possible, though not without -drawbacks (or hacks to avoid them) and currently not implemented. - -SPL support -============ -The main task of the SPL support is to bring up the DRAM controller and make -DRAM actually accessible. At the moment there is no documentation or source -code available which would do this. -There are currently two ways to overcome this situation: using a tainted 32-bit -SPL (involving some hacks and resulting in a non-redistributable binary, thus -not described here) or using the Allwinner boot0 blob. - -boot0 method -------------- -boot0 is Allwiner's secondary program loader and it can be used as some kind -of SPL replacement to get U-Boot up and running. -The binary is a 32 KByte blob and contained on every Pine64 image distributed -so far. It can be easily extracted from a micro SD card or an image file: -# dd if=/dev/sd<x> of=boot0.bin bs=8k skip=1 count=4 -where /dev/sd<x> is the device name of the uSD card or the name of the image -file. Apparently Allwinner allows re-distribution of this proprietary code -as-is. -For the time being this boot0 blob is the only redistributable way of making -U-Boot work on the Pine64. Beside loading the various parts of the (original) -firmware it also switches the core into AArch64 mode. -The original boot0 code looks for U-Boot at a certain place on an uSD card -(at 19096 KB), also it expects a header with magic bytes and a checksum. -There is a tool called boot0img[1] which takes a boot0.bin image and a compiled -U-Boot binary (plus other binaries) and will populate that header accordingly. -To make space for the magic header, the pine64_plus_defconfig will make sure -there is sufficient space at the beginning of the U-Boot binary. -boot0img will also take care of putting the different binaries at the right -places on the uSD card and works around unused, but mandatory parts by using -trampoline code. See the output of "boot0img -h" for more information. -boot0img can also patch boot0 to avoid loading U-Boot from 19MB, instead -fetching it from just behind the boot0 binary (-B option). - -FEL boot -========= -FEL is the name of the Allwinner defined USB boot protocol built-in the -mask ROM of most Allwinner SoCs. It allows to bootstrap a board solely -by using the USB-OTG interface and a host port on another computer. -Since FEL boot does not work with boot0, it requires the libdram hack, which -is not described here. - -[1] https://github.com/apritzel/pine64/ -[2] https://github.com/apritzel/arm-trusted-firmware.git diff --git a/board/sunxi/README.sunxi64 b/board/sunxi/README.sunxi64 new file mode 100644 index 0000000000..c492f749b8 --- /dev/null +++ b/board/sunxi/README.sunxi64 @@ -0,0 +1,165 @@ +Allwinner 64-bit boards README +============================== + +Newer Allwinner SoCs feature ARMv8 cores (ARM Cortex-A53) with support for +both the 64-bit AArch64 mode and the ARMv7 compatible 32-bit AArch32 mode. +Examples are the Allwinner A64 (used for instance on the Pine64 board) or +the Allwinner H5 SoC (as used on the OrangePi PC 2). +These SoCs are wired to start in AArch32 mode on reset and execute 32-bit +code from the Boot ROM (BROM). As this has some implications on U-Boot, this +file describes how to make full use of the 64-bit capabilities. + +Quick Start / Overview +====================== +- Build the ARM Trusted Firmware binary (see "ARM Trusted Firmware (ATF)" below) +- Build U-Boot (see "SPL/U-Boot" below) +- Transfer to an uSD card (see "microSD card" below) +- Boot and enjoy! + +Building the firmware +===================== + +The Allwinner A64/H5 firmware consists of three parts: U-Boot's SPL, an +ARM Trusted Firmware (ATF) build and the U-Boot proper. +The SPL will load both ATF and U-Boot proper along with the right device +tree blob (.dtb) and will pass execution to ATF (in EL3), which in turn will +drop into the U-Boot proper (in EL2). +As the ATF binary will become part of the U-Boot image file, you will need +to build it first. + + ARM Trusted Firmware (ATF) +---------------------------- +Checkout the "allwinner" branch from the github repository [1] and build it: +$ export CROSS_COMPILE=aarch64-linux-gnu- +$ make PLAT=sun50iw1p1 DEBUG=1 bl31 +The resulting binary is build/sun50iw1p1/debug/bl31.bin. Either put the +location of this file into the BL31 environment variable or copy this to +the root of your U-Boot build directory (or create a symbolic link). +$ export BL31=/src/arm-trusted-firmware/build/sun50iw1p1/debug/bl31.bin + (adjust the actual path accordingly) + + SPL/U-Boot +------------ +Both U-Boot proper and the SPL are using the 64-bit mode. As the boot ROM +enters the SPL still in AArch32 secure SVC mode, there is some shim code to +enter AArch64 very early. The rest of the SPL runs in AArch64 EL3. +U-Boot proper runs in EL2 and can load any AArch64 code (using the "go" +command), EFI applications (with "bootefi") or arm64 Linux kernel images +(often named "Image"), using the "booti" command. + +$ make clean +$ export CROSS_COMPILE=aarch64-linux-gnu- +$ make pine64_plus_defconfig +$ make + +This will build the SPL in spl/sunxi-spl.bin and a FIT image called u-boot.itb, +which contains the rest of the firmware. + + +Boot process +============ +The on-die BROM code will try several methods to load and execute the firmware. +On a typical board like the Pine64 this will result in the following boot order: + +1) Reading 32KB from sector 16 (@8K) of the microSD card to SRAM A1. If the +BROM finds the magic "eGON" header in the first bytes, it will execute that +code. If not (no SD card at all or invalid magic), it will: +2) Try to read 32KB from sector 16 (@8K) of memory connected to the MMC2 +controller, typically an on-board eMMC chip. If there is no eMMC or it does +not contain a valid boot header, it will: +3) Initialize the SPI0 controller and try to access a NOR flash connected to +it (using the CS0 pin). If a flash chip is found, the BROM will load the +first 32KB (from offset 0) into SRAM A1. Now it checks for the magic eGON +header and checksum and will execute the code upon finding it. If not, it will: +4) Initialize the USB OTG controller and will wait for a host to connect to +it, speaking the Allwinner proprietary (but deciphered) "FEL" USB protocol. + + +To boot the Pine64 board, you can use U-Boot and any of the described methods. + +FEL boot (USB OTG) +------------------ +FEL is the name of the Allwinner defined USB boot protocol built in the +mask ROM of most Allwinner SoCs. It allows to bootstrap a board solely +by using the USB-OTG interface and a host port on another computer. +As the FEL mode is controlled by the boot ROM, it expects to be running in +AArch32. For now the AArch64 SPL cannot properly return into FEL mode, so the +feature is disabled in the configuration at the moment. + +microSD card +------------ +Transfer the SPL and the U-Boot FIT image directly to an uSD card: +# dd if=spl/sunxi-spl.bin of=/dev/sdx bs=8k seek=1 +# dd if=u-boot.itb of=/dev/sdx bs=8k seek=5 +# sync +(replace /dev/sdx with you SD card device file name, which could be +/dev/mmcblk[x] as well). + +Alternatively you can concatenate the SPL and the U-Boot FIT image into a +single file and transfer that instead: +$ cat spl/sunxi-spl.bin u-boot.itb > u-boot-sunxi-with-spl.bin +# dd if=u-boot-sunxi-with-spl.bin of=/dev/sdx bs=8k seek=1 + +You can partition the microSD card, but leave the first MB unallocated (most +partitioning tools will do this anyway). + +NOR flash +--------- +Some boards (like the SoPine, Pinebook or the OrangePi PC2) come with a +soldered SPI NOR flash chip. On other boards like the Pine64 such a chip +can be connected to the SPI0/CS0 pins on the PI-2 headers. +Create the SPL and FIT image like described above for the SD card. +Now connect either an "A to A" USB cable to the upper USB port on the Pine64 +or get an adaptor and use a regular A-microB cable connected to it. Other +boards often have a proper micro-B USB socket connected to the USB OTB port. +Remove a microSD card from the slot and power on the board. +On your host computer download and build the sunxi-tools package[2], then +use "sunxi-fel" to access the board: +$ ./sunxi-fel ver -v -p +This should give you an output starting with: AWUSBFEX soc=00001689(A64) ... +Now use the sunxi-fel tool to write to the NOR flash: +$ ./sunxi-fel spiflash-write 0 spl/sunxi-spl.bin +$ ./sunxi-fel spiflash-write 32768 u-boot.itb +Now boot the board without an SD card inserted and you should see the +U-Boot prompt on the serial console. + +(Legacy) boot0 method +--------------------- +boot0 is Allwiner's secondary program loader and it can be used as some kind +of SPL replacement to get U-Boot up and running from an microSD card. +For some time using boot0 was the only option to get the Pine64 booted. +With working DRAM init code in U-Boot's SPL this is no longer necessary, +but this method is described here for the sake of completeness. +Please note that this method works only with the boot0 files shipped with +A64 based boards, the H5 uses an incompatible layout which is not supported +by this method. + +The boot0 binary is a 32 KByte blob and contained in the official Pine64 images +distributed by Pine64 or Allwinner. It can be easily extracted from a micro +SD card or an image file: +# dd if=/dev/sd<x> of=boot0.bin bs=8k skip=1 count=4 +where /dev/sd<x> is the device name of the uSD card or the name of the image +file. Apparently Allwinner allows re-distribution of this proprietary code +"as-is". +This boot0 blob takes care of DRAM initialisation and loads the remaining +firmware parts, then switches the core into AArch64 mode. +The original boot0 code looks for U-Boot at a certain place on an uSD card +(at 19096 KB), also it expects a header with magic bytes and a checksum. +There is a tool called boot0img[3] which takes a boot0.bin image and a compiled +U-Boot binary (plus other binaries) and will populate that header accordingly. +To make space for the magic header, the pine64_plus_defconfig will make sure +there is sufficient space at the beginning of the U-Boot binary. +boot0img will also take care of putting the different binaries at the right +places on the uSD card and works around unused, but mandatory parts by using +trampoline code. See the output of "boot0img -h" for more information. +boot0img can also patch boot0 to avoid loading U-Boot from 19MB, instead +fetching it from just behind the boot0 binary (-B option). +$ ./boot0img -o firmware.img -B boot0.img -u u-boot-dtb.bin -e -s bl31.bin \ +-a 0x44008 -d trampoline64:0x44000 +Then write this image to a microSD card, replacing /dev/sdx with the right +device file (see above): +$ dd if=firmware.img of=/dev/sdx bs=8k seek=1 + +[1] https://github.com/apritzel/arm-trusted-firmware.git +[2] git://github.com/linux-sunxi/sunxi-tools.git +[3] https://github.com/apritzel/pine64/ |