diff options
| -rw-r--r-- | drivers/i2c/fsl_i2c.c | 114 |
1 files changed, 105 insertions, 9 deletions
diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c index 22485ea916..dde057124e 100644 --- a/drivers/i2c/fsl_i2c.c +++ b/drivers/i2c/fsl_i2c.c @@ -32,6 +32,8 @@ #define I2C_READ_BIT 1 #define I2C_WRITE_BIT 0 +DECLARE_GLOBAL_DATA_PTR; + /* Initialize the bus pointer to whatever one the SPD EEPROM is on. * Default is bus 0. This is necessary because the DDR initialization * runs from ROM, and we can't switch buses because we can't modify @@ -43,24 +45,111 @@ static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CFG_SPD_BUS static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = 0; #endif -static volatile struct fsl_i2c *i2c_dev[2] = { +static unsigned int i2c_bus_speed[2] = {CFG_I2C_SPEED, CFG_I2C_SPEED}; + +static const struct fsl_i2c *i2c_dev[2] = { (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET), #ifdef CFG_I2C2_OFFSET (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET) #endif }; +/* I2C speed map for a DFSR value of 1 */ + +/* + * Map I2C frequency dividers to FDR and DFSR values + * + * This structure is used to define the elements of a table that maps I2C + * frequency divider (I2C clock rate divided by I2C bus speed) to a value to be + * programmed into the Frequency Divider Ratio (FDR) and Digital Filter + * Sampling Rate (DFSR) registers. + * + * The actual table should be defined in the board file, and it must be called + * fsl_i2c_speed_map[]. + * + * The last entry of the table must have a value of {-1, X}, where X is same + * FDR/DFSR values as the second-to-last entry. This guarantees that any + * search through the array will always find a match. + * + * The values of the divider must be in increasing numerical order, i.e. + * fsl_i2c_speed_map[x+1].divider > fsl_i2c_speed_map[x].divider. + * + * For this table, the values are based on a value of 1 for the DFSR + * register. See the application note AN2919 "Determining the I2C Frequency + * Divider Ratio for SCL" + */ +static const struct { + unsigned short divider; + u8 dfsr; + u8 fdr; +} fsl_i2c_speed_map[] = { + {160, 1, 32}, {192, 1, 33}, {224, 1, 34}, {256, 1, 35}, + {288, 1, 0}, {320, 1, 1}, {352, 6, 1}, {384, 1, 2}, {416, 6, 2}, + {448, 1, 38}, {480, 1, 3}, {512, 1, 39}, {544, 11, 3}, {576, 1, 4}, + {608, 22, 3}, {640, 1, 5}, {672, 32, 3}, {704, 11, 5}, {736, 43, 3}, + {768, 1, 6}, {800, 54, 3}, {832, 11, 6}, {896, 1, 42}, {960, 1, 7}, + {1024, 1, 43}, {1088, 22, 7}, {1152, 1, 8}, {1216, 43, 7}, {1280, 1, 9}, + {1408, 22, 9}, {1536, 1, 10}, {1664, 22, 10}, {1792, 1, 46}, + {1920, 1, 11}, {2048, 1, 47}, {2176, 43, 11}, {2304, 1, 12}, + {2560, 1, 13}, {2816, 43, 13}, {3072, 1, 14}, {3328, 43, 14}, + {3584, 1, 50}, {3840, 1, 15}, {4096, 1, 51}, {4608, 1, 16}, + {5120, 1, 17}, {6144, 1, 18}, {7168, 1, 54}, {7680, 1, 19}, + {8192, 1, 55}, {9216, 1, 20}, {10240, 1, 21}, {12288, 1, 22}, + {14336, 1, 58}, {15360, 1, 23}, {16384, 1, 59}, {18432, 1, 24}, + {20480, 1, 25}, {24576, 1, 26}, {28672, 1, 62}, {30720, 1, 27}, + {32768, 1, 63}, {36864, 1, 28}, {40960, 1, 29}, {49152, 1, 30}, + {61440, 1, 31}, {-1, 1, 31} +}; + +/** + * Set the I2C bus speed for a given I2C device + * + * @param dev: the I2C device + * @i2c_clk: I2C bus clock frequency + * @speed: the desired speed of the bus + * + * The I2C device must be stopped before calling this function. + * + * The return value is the actual bus speed that is set. + */ +static unsigned int set_i2c_bus_speed(const struct fsl_i2c *dev, + unsigned int i2c_clk, unsigned int speed) +{ + unsigned short divider = min(i2c_clk / speed, (unsigned short) -1); + unsigned int i; + u8 fdr, dfsr; + + /* + * We want to choose an FDR/DFSR that generates an I2C bus speed that + * is equal to or lower than the requested speed. That means that we + * want the first divider that is equal to or greater than the + * calculated divider. + */ + + for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++) + if (fsl_i2c_speed_map[i].divider >= divider) { + dfsr = fsl_i2c_speed_map[i].dfsr; + fdr = fsl_i2c_speed_map[i].fdr; + speed = i2c_clk / fsl_i2c_speed_map[i].divider; + break; + } + + writeb(fdr, &dev->fdr); /* set bus speed */ + writeb(dfsr, &dev->dfsrr); /* set default filter */ + + return speed; +} + void i2c_init(int speed, int slaveadd) { - volatile struct fsl_i2c *dev; + struct fsl_i2c *dev; dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET); writeb(0, &dev->cr); /* stop I2C controller */ udelay(5); /* let it shutdown in peace */ - writeb(0x3F, &dev->fdr); /* set bus speed */ - writeb(0x3F, &dev->dfsrr); /* set default filter */ + i2c_bus_speed[0] = set_i2c_bus_speed(dev, gd->i2c1_clk, speed); writeb(slaveadd << 1, &dev->adr); /* write slave address */ writeb(0x0, &dev->sr); /* clear status register */ writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ @@ -70,12 +159,11 @@ i2c_init(int speed, int slaveadd) writeb(0, &dev->cr); /* stop I2C controller */ udelay(5); /* let it shutdown in peace */ - writeb(0x3F, &dev->fdr); /* set bus speed */ - writeb(0x3F, &dev->dfsrr); /* set default filter */ + i2c_bus_speed[1] = set_i2c_bus_speed(dev, gd->i2c2_clk, speed); writeb(slaveadd << 1, &dev->adr); /* write slave address */ writeb(0x0, &dev->sr); /* clear status register */ writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ -#endif /* CFG_I2C2_OFFSET */ +#endif } static __inline__ int @@ -279,7 +367,14 @@ int i2c_set_bus_num(unsigned int bus) int i2c_set_bus_speed(unsigned int speed) { - return -1; + unsigned int i2c_clk = (i2c_bus_num == 1) ? gd->i2c2_clk : gd->i2c1_clk; + + writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */ + i2c_bus_speed[i2c_bus_num] = + set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed); + writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */ + + return 0; } unsigned int i2c_get_bus_num(void) @@ -289,7 +384,8 @@ unsigned int i2c_get_bus_num(void) unsigned int i2c_get_bus_speed(void) { - return 0; + return i2c_bus_speed[i2c_bus_num]; } + #endif /* CONFIG_HARD_I2C */ #endif /* CONFIG_FSL_I2C */ |