diff options
Diffstat (limited to 'arch/arm/dts/armada-xp-synology-ds414.dts')
| -rw-r--r-- | arch/arm/dts/armada-xp-synology-ds414.dts | 199 |
1 files changed, 98 insertions, 101 deletions
diff --git a/arch/arm/dts/armada-xp-synology-ds414.dts b/arch/arm/dts/armada-xp-synology-ds414.dts index 0a60ddfa41..861967cd7e 100644 --- a/arch/arm/dts/armada-xp-synology-ds414.dts +++ b/arch/arm/dts/armada-xp-synology-ds414.dts @@ -1,13 +1,9 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* * Device Tree file for Synology DS414 * * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org> * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version - * 2 of the License, or (at your option) any later version. - * * Note: this Device Tree assumes that the bootloader has remapped the * internal registers to 0xf1000000 (instead of the old 0xd0000000). * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot @@ -42,36 +38,16 @@ spi0 = &spi0; }; - memory { + memory@0 { device_type = "memory"; reg = <0 0x00000000 0 0x40000000>; /* 1GB */ }; soc { ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 - MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; - - pcie-controller { - status = "okay"; - - /* - * Connected to Marvell 88SX7042 SATA-II controller - * handling the four disks. - */ - pcie@1,0 { - /* Port 0, Lane 0 */ - status = "okay"; - }; - - /* - * Connected to EtronTech EJ168A XHCI controller - * providing the two rear USB 3.0 ports. - */ - pcie@5,0 { - /* Port 1, Lane 0 */ - status = "okay"; - }; - }; + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 + MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000 + MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000>; internal-regs { @@ -80,64 +56,6 @@ status = "disabled"; }; - spi0: spi@10600 { - status = "okay"; - u-boot,dm-pre-reloc; - - spi-flash@0 { - u-boot,dm-pre-reloc; - #address-cells = <1>; - #size-cells = <1>; - compatible = "micron,n25q064"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <20000000>; - - /* - * Warning! - * - * Synology u-boot uses its compiled-in environment - * and it seems Synology did not care to change u-boot - * default configuration in order to allow saving a - * modified environment at a sensible location. So, - * if you do a 'saveenv' under u-boot, your modified - * environment will be saved at 1MB after the start - * of the flash, i.e. in the middle of the uImage. - * For that reason, it is strongly advised not to - * change the default environment, unless you know - * what you are doing. - */ - partition@00000000 { /* u-boot */ - label = "RedBoot"; - reg = <0x00000000 0x000d0000>; /* 832KB */ - }; - - partition@000c0000 { /* uImage */ - label = "zImage"; - reg = <0x000d0000 0x002d0000>; /* 2880KB */ - }; - - partition@003a0000 { /* uInitramfs */ - label = "rd.gz"; - reg = <0x003a0000 0x00430000>; /* 4250KB */ - }; - - partition@007d0000 { /* MAC address and serial number */ - label = "vendor"; - reg = <0x007d0000 0x00010000>; /* 64KB */ - }; - - partition@007e0000 { - label = "RedBoot config"; - reg = <0x007e0000 0x00010000>; /* 64KB */ - }; - - partition@007f0000 { - label = "FIS directory"; - reg = <0x007f0000 0x00010000>; /* 64KB */ - }; - }; - }; - i2c@11000 { clock-frequency = <400000>; status = "okay"; @@ -179,16 +97,6 @@ status = "okay"; }; - mdio { - phy0: ethernet-phy@0 { /* Marvell 88E1512 */ - reg = <0>; - }; - - phy1: ethernet-phy@1 { /* Marvell 88E1512 */ - reg = <1>; - }; - }; - ethernet@70000 { status = "okay"; pinctrl-0 = <&ge0_rgmii_pins>; @@ -215,7 +123,7 @@ &sata3_pwr_pin &sata4_pwr_pin>; pinctrl-names = "default"; - sata1_regulator: sata1-regulator { + sata1_regulator: sata1-regulator@1 { compatible = "regulator-fixed"; reg = <1>; regulator-name = "SATA1 Power"; @@ -228,7 +136,7 @@ gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>; }; - sata2_regulator: sata2-regulator { + sata2_regulator: sata2-regulator@2 { compatible = "regulator-fixed"; reg = <2>; regulator-name = "SATA2 Power"; @@ -241,7 +149,7 @@ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; }; - sata3_regulator: sata3-regulator { + sata3_regulator: sata3-regulator@3 { compatible = "regulator-fixed"; reg = <3>; regulator-name = "SATA3 Power"; @@ -254,7 +162,7 @@ gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; }; - sata4_regulator: sata4-regulator { + sata4_regulator: sata4-regulator@4 { compatible = "regulator-fixed"; reg = <4>; regulator-name = "SATA4 Power"; @@ -269,6 +177,39 @@ }; }; +&pciec { + status = "okay"; + + /* + * Connected to Marvell 88SX7042 SATA-II controller + * handling the four disks. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* + * Connected to EtronTech EJ168A XHCI controller + * providing the two rear USB 3.0 ports. + */ + pcie@5,0 { + /* Port 1, Lane 0 */ + status = "okay"; + }; +}; + + +&mdio { + phy0: ethernet-phy@0 { /* Marvell 88E1512 */ + reg = <0>; + }; + + phy1: ethernet-phy@1 { /* Marvell 88E1512 */ + reg = <1>; + }; +}; + &pinctrl { sata1_pwr_pin: sata1-pwr-pin { marvell,pins = "mpp42"; @@ -335,3 +276,59 @@ marvell,function = "gpio"; }; }; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q064", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <20000000>; + + /* + * Warning! + * + * Synology u-boot uses its compiled-in environment + * and it seems Synology did not care to change u-boot + * default configuration in order to allow saving a + * modified environment at a sensible location. So, + * if you do a 'saveenv' under u-boot, your modified + * environment will be saved at 1MB after the start + * of the flash, i.e. in the middle of the uImage. + * For that reason, it is strongly advised not to + * change the default environment, unless you know + * what you are doing. + */ + partition@0 { /* u-boot */ + label = "RedBoot"; + reg = <0x00000000 0x000d0000>; /* 832KB */ + }; + + partition@c0000 { /* uImage */ + label = "zImage"; + reg = <0x000d0000 0x002d0000>; /* 2880KB */ + }; + + partition@3a0000 { /* uInitramfs */ + label = "rd.gz"; + reg = <0x003a0000 0x00430000>; /* 4250KB */ + }; + + partition@7d0000 { /* MAC address and serial number */ + label = "vendor"; + reg = <0x007d0000 0x00010000>; /* 64KB */ + }; + + partition@7e0000 { + label = "RedBoot config"; + reg = <0x007e0000 0x00010000>; /* 64KB */ + }; + + partition@7f0000 { + label = "FIS directory"; + reg = <0x007f0000 0x00010000>; /* 64KB */ + }; + }; +}; |