diff options
Diffstat (limited to 'arch/arm/dts/meson-gxbb-nanopi-k2.dts')
| -rw-r--r-- | arch/arm/dts/meson-gxbb-nanopi-k2.dts | 26 |
1 files changed, 15 insertions, 11 deletions
diff --git a/arch/arm/dts/meson-gxbb-nanopi-k2.dts b/arch/arm/dts/meson-gxbb-nanopi-k2.dts index cbe99bd4e0..d6ca684e0e 100644 --- a/arch/arm/dts/meson-gxbb-nanopi-k2.dts +++ b/arch/arm/dts/meson-gxbb-nanopi-k2.dts @@ -10,6 +10,7 @@ / { compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb"; + model = "FriendlyARM NanoPi K2"; aliases { serial0 = &uart_AO; @@ -154,10 +155,6 @@ amlogic,tx-delay-ns = <2>; - snps,reset-gpio = <&gpio GPIOZ_14 0>; - snps,reset-delays-us = <0 10000 1000000>; - snps,reset-active-low; - mdio { compatible = "snps,dwmac-mdio"; #address-cells = <1>; @@ -166,6 +163,11 @@ eth_phy0: ethernet-phy@0 { /* Realtek RTL8211F (0x001cc916) */ reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <30000>; + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio_intc>; /* MAC_INTR on GPIOZ_15 */ interrupts = <29 IRQ_TYPE_LEVEL_LOW>; @@ -191,7 +193,7 @@ pinctrl-names = "default"; }; -&pinctrl_aobus { +&gpio_ao { gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In", "VCCK En", "CON1 Header Pin31", "I2S Header Pin6", "IR In", "I2S Header Pin7", @@ -201,7 +203,7 @@ ""; }; -&pinctrl_periphs { +&gpio { gpio-line-names = /* Bank GPIOZ */ "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk", "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2", @@ -273,11 +275,14 @@ bus-width = <4>; cap-sd-highspeed; - max-frequency = <200000000>; + max-frequency = <50000000>; non-removable; disable-wp; + /* WiFi firmware requires power to be kept while in suspend */ + keep-power-in-suspend; + mmc-pwrseq = <&sdio_pwrseq>; vmmc-supply = <&vddio_ao3v3>; @@ -301,12 +306,11 @@ sd-uhs-sdr12; sd-uhs-sdr25; sd-uhs-sdr50; - sd-uhs-sdr104; - max-frequency = <200000000>; + sd-uhs-ddr50; + max-frequency = <100000000>; disable-wp; - cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; - cd-inverted; + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; vmmc-supply = <&vddio_ao3v3>; vqmmc-supply = <&vddio_tf>; |