diff options
Diffstat (limited to 'arch/arm/dts/zynqmp-zcu102-revA.dts')
| -rw-r--r-- | arch/arm/dts/zynqmp-zcu102-revA.dts | 399 |
1 files changed, 46 insertions, 353 deletions
diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts index 2be6eb0eb5..b7c638bc9e 100644 --- a/arch/arm/dts/zynqmp-zcu102-revA.dts +++ b/arch/arm/dts/zynqmp-zcu102-revA.dts @@ -1,19 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0+ /* * dts file for Xilinx ZynqMP ZCU102 RevA * - * (C) Copyright 2015, Xilinx, Inc. + * (C) Copyright 2015 - 2018, Xilinx, Inc. * * Michal Simek <michal.simek@xilinx.com> - * - * SPDX-License-Identifier: GPL-2.0+ */ /dts-v1/; #include "zynqmp.dtsi" #include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> #include <dt-bindings/phy/phy.h> / { @@ -52,7 +51,7 @@ sw19 { label = "sw19"; gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; - linux,code = <108>; /* down */ + linux,code = <KEY_DOWN>; gpio-key,wakeup; autorepeat; }; @@ -70,15 +69,12 @@ &can1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can1_default>; }; &dcc { status = "okay"; }; -/* fpd_dma clk 667MHz, lpd_dma 500MHz */ &fpd_dma_chan1 { status = "okay"; }; @@ -115,8 +111,6 @@ status = "okay"; phy-handle = <&phy0>; phy-mode = "rgmii-id"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gem3_default>; phy0: phy@21 { reg = <21>; ti,rx-internal-delay = <0x8>; @@ -127,8 +121,6 @@ &gpio { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_default>; }; &gpu { @@ -138,19 +130,8 @@ &i2c0 { status = "okay"; clock-frequency = <400000>; - pinctrl-names = "default", "gpio"; - pinctrl-0 = <&pinctrl_i2c0_default>; - pinctrl-1 = <&pinctrl_i2c0_gpio>; - scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; - sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; tca6416_u97: gpio@20 { - /* - * Enable all GTs to out from U-Boot - * i2c mw 20 6 0 - setup IO to output - * i2c mw 20 2 ef - setup output values on pins 0-7 - * i2c mw 20 3 ff - setup output values on pins 10-17 - */ compatible = "ti,tca6416"; reg = <0x20>; gpio-controller; @@ -194,7 +175,7 @@ }; }; - tca6416_u61: gpio@21 { /* FIXME enable it by i2c mw 21 6 0 */ + tca6416_u61: gpio@21 { compatible = "ti,tca6416"; reg = <0x21>; gpio-controller; @@ -220,12 +201,12 @@ */ }; - i2cswitch@75 { /* u60 */ + i2c-mux@75 { /* u60 */ compatible = "nxp,pca9544"; #address-cells = <1>; #size-cells = <0>; reg = <0x75>; - i2c@0 { /* i2c mw 75 0 1 */ + i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; @@ -281,7 +262,7 @@ shunt-resistor = <5000>; }; }; - i2c@1 { /* i2c mw 75 0 1 */ + i2c@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>; @@ -327,97 +308,85 @@ shunt-resistor = <5000>; }; }; - i2c@2 { /* i2c mw 75 0 1 */ + i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; /* MAXIM_PMBUS - 00 */ max15301@a { /* u46 */ - compatible = "max15301"; + compatible = "maxim,max15301"; reg = <0xa>; }; max15303@b { /* u4 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0xb>; }; max15303@10 { /* u13 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x10>; }; max15301@13 { /* u47 */ - compatible = "max15301"; + compatible = "maxim,max15301"; reg = <0x13>; }; max15303@14 { /* u7 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x14>; }; max15303@15 { /* u6 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x15>; }; max15303@16 { /* u10 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x16>; }; max15303@17 { /* u9 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x17>; }; max15301@18 { /* u63 */ - compatible = "max15301"; + compatible = "maxim,max15301"; reg = <0x18>; }; max15303@1a { /* u49 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x1a>; }; max15303@1d { /* u18 */ - compatible = "max15303"; + compatible = "maxim,max15303"; reg = <0x1d>; }; max15303@20 { /* u8 */ - compatible = "max15303"; + compatible = "maxim,max15303"; status = "disabled"; /* unreachable */ reg = <0x20>; }; -/* drivers/hwmon/pmbus/Kconfig:86: be called max20751. -drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o -*/ - max20751@72 { /* u95 FIXME - not detected */ - compatible = "max20751"; + max20751@72 { /* u95 */ + compatible = "maxim,max20751"; reg = <0x72>; }; - max20751@73 { /* u96 FIXME - not detected */ - compatible = "max20751"; + max20751@73 { /* u96 */ + compatible = "maxim,max20751"; reg = <0x73>; }; }; /* Bus 3 is not connected */ }; - - /* FIXME PMOD - j160 */ - /* FIXME MSP430F - u41 - not detected */ }; &i2c1 { status = "okay"; clock-frequency = <400000>; - pinctrl-names = "default", "gpio"; - pinctrl-0 = <&pinctrl_i2c1_default>; - pinctrl-1 = <&pinctrl_i2c1_gpio>; - scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; - sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; - - /* FIXME PL i2c via PCA9306 - u45 */ - /* FIXME MSP430 - u41 - not detected */ - i2cswitch@74 { /* u34 */ + + /* PL i2c via PCA9306 - u45 */ + i2c-mux@74 { /* u34 */ compatible = "nxp,pca9548"; #address-cells = <1>; #size-cells = <0>; reg = <0x74>; - i2c@0 { /* i2c mw 74 0 1 */ + i2c@0 { #address-cells = <1>; #size-cells = <0>; reg = <0>; @@ -430,25 +399,25 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o * 768B - 1024B address 0x57 */ eeprom: eeprom@54 { /* u23 */ - compatible = "at,24c08"; + compatible = "atmel,24c08"; reg = <0x54>; }; }; - i2c@1 { /* i2c mw 74 0 2 */ + i2c@1 { #address-cells = <1>; #size-cells = <0>; reg = <1>; - si5341: clock-generator1@36 { /* SI5341 - u69 */ - compatible = "si5341"; + si5341: clock-generator@36 { /* SI5341 - u69 */ + compatible = "silabs,si5341"; reg = <0x36>; }; }; - i2c@2 { /* i2c mw 74 0 4 */ + i2c@2 { #address-cells = <1>; #size-cells = <0>; reg = <2>; - si570_1: clock-generator2@5d { /* USER SI570 - u42 */ + si570_1: clock-generator@5d { /* USER SI570 - u42 */ #clock-cells = <0>; compatible = "silabs,si570"; reg = <0x5d>; @@ -457,11 +426,11 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o clock-frequency = <300000000>; }; }; - i2c@3 { /* i2c mw 74 0 8 */ + i2c@3 { #address-cells = <1>; #size-cells = <0>; reg = <3>; - si570_2: clock-generator3@5d { /* USER MGT SI570 - u56 */ + si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */ #clock-cells = <0>; compatible = "silabs,si570"; reg = <0x5d>; @@ -470,11 +439,11 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o clock-frequency = <148500000>; }; }; - i2c@4 { /* i2c mw 74 0 10 */ + i2c@4 { #address-cells = <1>; #size-cells = <0>; reg = <4>; - si5328: clock-generator4@69 {/* SI5328 - u20 */ + si5328: clock-generator@69 {/* SI5328 - u20 */ compatible = "silabs,si5328"; reg = <0x69>; /* @@ -487,7 +456,7 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o /* 5 - 7 unconnected */ }; - i2cswitch@75 { + i2c-mux@75 { compatible = "nxp,pca9548"; /* u135 */ #address-cells = <1>; #size-cells = <0>; @@ -511,29 +480,24 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o reg = <2>; /* SYSMON */ }; - i2c@3 { /* i2c mw 75 0 8 */ + i2c@3 { #address-cells = <1>; #size-cells = <0>; reg = <3>; /* DDR4 SODIMM */ - dev@19 { /* u-boot detection */ - compatible = "xxx"; + dev@19 { reg = <0x19>; }; - dev@30 { /* u-boot detection */ - compatible = "xxx"; + dev@30 { reg = <0x30>; }; - dev@35 { /* u-boot detection */ - compatible = "xxx"; + dev@35 { reg = <0x35>; }; - dev@36 { /* u-boot detection */ - compatible = "xxx"; + dev@36 { reg = <0x36>; }; - dev@51 { /* u-boot detection - maybe SPD */ - compatible = "xxx"; + dev@51 { reg = <0x51>; }; }; @@ -564,269 +528,6 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o }; }; -&pinctrl0 { - status = "okay"; - pinctrl_i2c0_default: i2c0-default { - mux { - groups = "i2c0_3_grp"; - function = "i2c0"; - }; - - conf { - groups = "i2c0_3_grp"; - bias-pull-up; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - }; - - pinctrl_i2c0_gpio: i2c0-gpio { - mux { - groups = "gpio0_14_grp", "gpio0_15_grp"; - function = "gpio0"; - }; - - conf { - groups = "gpio0_14_grp", "gpio0_15_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - }; - - pinctrl_i2c1_default: i2c1-default { - mux { - groups = "i2c1_4_grp"; - function = "i2c1"; - }; - - conf { - groups = "i2c1_4_grp"; - bias-pull-up; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - }; - - pinctrl_i2c1_gpio: i2c1-gpio { - mux { - groups = "gpio0_16_grp", "gpio0_17_grp"; - function = "gpio0"; - }; - - conf { - groups = "gpio0_16_grp", "gpio0_17_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - }; - - pinctrl_uart0_default: uart0-default { - mux { - groups = "uart0_4_grp"; - function = "uart0"; - }; - - conf { - groups = "uart0_4_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-rx { - pins = "MIO18"; - bias-high-impedance; - }; - - conf-tx { - pins = "MIO19"; - bias-disable; - }; - }; - - pinctrl_uart1_default: uart1-default { - mux { - groups = "uart1_5_grp"; - function = "uart1"; - }; - - conf { - groups = "uart1_5_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-rx { - pins = "MIO21"; - bias-high-impedance; - }; - - conf-tx { - pins = "MIO20"; - bias-disable; - }; - }; - - pinctrl_usb0_default: usb0-default { - mux { - groups = "usb0_0_grp"; - function = "usb0"; - }; - - conf { - groups = "usb0_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-rx { - pins = "MIO52", "MIO53", "MIO55"; - bias-high-impedance; - }; - - conf-tx { - pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", - "MIO60", "MIO61", "MIO62", "MIO63"; - bias-disable; - }; - }; - - pinctrl_gem3_default: gem3-default { - mux { - function = "ethernet3"; - groups = "ethernet3_0_grp"; - }; - - conf { - groups = "ethernet3_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-rx { - pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74", - "MIO75"; - bias-high-impedance; - low-power-disable; - }; - - conf-tx { - pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68", - "MIO69"; - bias-disable; - low-power-enable; - }; - - mux-mdio { - function = "mdio3"; - groups = "mdio3_0_grp"; - }; - - conf-mdio { - groups = "mdio3_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - bias-disable; - }; - }; - - pinctrl_can1_default: can1-default { - mux { - function = "can1"; - groups = "can1_6_grp"; - }; - - conf { - groups = "can1_6_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-rx { - pins = "MIO25"; - bias-high-impedance; - }; - - conf-tx { - pins = "MIO24"; - bias-disable; - }; - }; - - pinctrl_sdhci1_default: sdhci1-default { - mux { - groups = "sdio1_0_grp"; - function = "sdio1"; - }; - - conf { - groups = "sdio1_0_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - bias-disable; - }; - - mux-cd { - groups = "sdio1_0_cd_grp"; - function = "sdio1_cd"; - }; - - conf-cd { - groups = "sdio1_0_cd_grp"; - bias-high-impedance; - bias-pull-up; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - mux-wp { - groups = "sdio1_0_wp_grp"; - function = "sdio1_wp"; - }; - - conf-wp { - groups = "sdio1_0_wp_grp"; - bias-high-impedance; - bias-pull-up; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - }; - - pinctrl_gpio_default: gpio-default { - mux-sw { - function = "gpio0"; - groups = "gpio0_22_grp", "gpio0_23_grp"; - }; - - conf-sw { - groups = "gpio0_22_grp", "gpio0_23_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - mux-msp { - function = "gpio0"; - groups = "gpio0_13_grp", "gpio0_38_grp"; - }; - - conf-msp { - groups = "gpio0_13_grp", "gpio0_38_grp"; - slew-rate = <SLEW_RATE_SLOW>; - io-standard = <IO_STANDARD_LVCMOS18>; - }; - - conf-pull-up { - pins = "MIO22", "MIO23"; - bias-pull-up; - }; - - conf-pull-none { - pins = "MIO13", "MIO38"; - bias-disable; - }; - }; -}; - &pcie { status = "okay"; }; @@ -883,8 +584,6 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o /* SD1 with level shifter */ &sdhci1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_sdhci1_default>; no-1-8-v; /* for 1.0 silicon */ xlnx,mio_bank = <1>; }; @@ -895,21 +594,15 @@ drivers/hwmon/pmbus/Makefile:11:obj-$(CONFIG_SENSORS_MAX20751) += max20751.o &uart0 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart0_default>; }; &uart1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_default>; }; /* ULPI SMSC USB3320 */ &usb0 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usb0_default>; }; &dwc3_0 { |