1 files changed, 892 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/clocks-common.c b/arch/arm/mach-omap2/clocks-common.c
new file mode 100644
index 0000000000..9b97583104
--- /dev/null
+++ b/arch/arm/mach-omap2/clocks-common.c
@@ -0,0 +1,892 @@
+/*
+ *
+ * Clock initialization for OMAP4
+ *
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Aneesh V <aneesh@ti.com>
+ *
+ * Based on previous work by:
+ *	Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *	Rajendra Nayak <rnayak@ti.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <i2c.h>
+#include <asm/omap_common.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/utils.h>
+#include <asm/omap_gpio.h>
+#include <asm/emif.h>
+
+#ifndef CONFIG_SPL_BUILD
+/*
+ * printing to console doesn't work unless
+ * this code is executed from SPL
+ */
+#define printf(fmt, args...)
+#define puts(s)
+#endif
+
+const u32 sys_clk_array[8] = {
+	12000000,	       /* 12 MHz */
+	20000000,		/* 20 MHz */
+	16800000,	       /* 16.8 MHz */
+	19200000,	       /* 19.2 MHz */
+	26000000,	       /* 26 MHz */
+	27000000,	       /* 27 MHz */
+	38400000,	       /* 38.4 MHz */
+};
+
+static inline u32 __get_sys_clk_index(void)
+{
+	s8 ind;
+	/*
+	 * For ES1 the ROM code calibration of sys clock is not reliable
+	 * due to hw issue. So, use hard-coded value. If this value is not
+	 * correct for any board over-ride this function in board file
+	 * From ES2.0 onwards you will get this information from
+	 * CM_SYS_CLKSEL
+	 */
+	if (omap_revision() == OMAP4430_ES1_0)
+		ind = OMAP_SYS_CLK_IND_38_4_MHZ;
+	else {
+		/* SYS_CLKSEL - 1 to match the dpll param array indices */
+		ind = (readl((*prcm)->cm_sys_clksel) &
+			CM_SYS_CLKSEL_SYS_CLKSEL_MASK) - 1;
+	}
+	return ind;
+}
+
+u32 get_sys_clk_index(void)
+	__attribute__ ((weak, alias("__get_sys_clk_index")));
+
+u32 get_sys_clk_freq(void)
+{
+	u8 index = get_sys_clk_index();
+	return sys_clk_array[index];
+}
+
+void setup_post_dividers(u32 const base, const struct dpll_params *params)
+{
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	/* Setup post-dividers */
+	if (params->m2 >= 0)
+		writel(params->m2, &dpll_regs->cm_div_m2_dpll);
+	if (params->m3 >= 0)
+		writel(params->m3, &dpll_regs->cm_div_m3_dpll);
+	if (params->m4_h11 >= 0)
+		writel(params->m4_h11, &dpll_regs->cm_div_m4_h11_dpll);
+	if (params->m5_h12 >= 0)
+		writel(params->m5_h12, &dpll_regs->cm_div_m5_h12_dpll);
+	if (params->m6_h13 >= 0)
+		writel(params->m6_h13, &dpll_regs->cm_div_m6_h13_dpll);
+	if (params->m7_h14 >= 0)
+		writel(params->m7_h14, &dpll_regs->cm_div_m7_h14_dpll);
+	if (params->h21 >= 0)
+		writel(params->h21, &dpll_regs->cm_div_h21_dpll);
+	if (params->h22 >= 0)
+		writel(params->h22, &dpll_regs->cm_div_h22_dpll);
+	if (params->h23 >= 0)
+		writel(params->h23, &dpll_regs->cm_div_h23_dpll);
+	if (params->h24 >= 0)
+		writel(params->h24, &dpll_regs->cm_div_h24_dpll);
+}
+
+static inline void do_bypass_dpll(u32 const base)
+{
+	struct dpll_regs *dpll_regs = (struct dpll_regs *)base;
+
+	clrsetbits_le32(&dpll_regs->cm_clkmode_dpll,
+			CM_CLKMODE_DPLL_DPLL_EN_MASK,
+			DPLL_EN_FAST_RELOCK_BYPASS <<
+			CM_CLKMODE_DPLL_EN_SHIFT);
+}
+
+static inline void wait_for_bypass(u32 const base)
+{
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	if (!wait_on_value(ST_DPLL_CLK_MASK, 0, &dpll_regs->cm_idlest_dpll,
+				LDELAY)) {
+		printf("Bypassing DPLL failed %x\n", base);
+	}
+}
+
+static inline void do_lock_dpll(u32 const base)
+{
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	clrsetbits_le32(&dpll_regs->cm_clkmode_dpll,
+		      CM_CLKMODE_DPLL_DPLL_EN_MASK,
+		      DPLL_EN_LOCK << CM_CLKMODE_DPLL_EN_SHIFT);
+}
+
+static inline void wait_for_lock(u32 const base)
+{
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	if (!wait_on_value(ST_DPLL_CLK_MASK, ST_DPLL_CLK_MASK,
+		&dpll_regs->cm_idlest_dpll, LDELAY)) {
+		printf("DPLL locking failed for %x\n", base);
+		hang();
+	}
+}
+
+inline u32 check_for_lock(u32 const base)
+{
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+	u32 lock = readl(&dpll_regs->cm_idlest_dpll) & ST_DPLL_CLK_MASK;
+
+	return lock;
+}
+
+const struct dpll_params *get_mpu_dpll_params(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->mpu[sysclk_ind];
+}
+
+const struct dpll_params *get_core_dpll_params(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->core[sysclk_ind];
+}
+
+const struct dpll_params *get_per_dpll_params(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->per[sysclk_ind];
+}
+
+const struct dpll_params *get_iva_dpll_params(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->iva[sysclk_ind];
+}
+
+const struct dpll_params *get_usb_dpll_params(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->usb[sysclk_ind];
+}
+
+const struct dpll_params *get_abe_dpll_params(struct dplls const *dpll_data)
+{
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+	u32 sysclk_ind = get_sys_clk_index();
+	return &dpll_data->abe[sysclk_ind];
+#else
+	return dpll_data->abe;
+#endif
+}
+
+static const struct dpll_params *get_ddr_dpll_params
+			(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+
+	if (!dpll_data->ddr)
+		return NULL;
+	return &dpll_data->ddr[sysclk_ind];
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static const struct dpll_params *get_gmac_dpll_params
+			(struct dplls const *dpll_data)
+{
+	u32 sysclk_ind = get_sys_clk_index();
+
+	if (!dpll_data->gmac)
+		return NULL;
+	return &dpll_data->gmac[sysclk_ind];
+}
+#endif
+
+static void do_setup_dpll(u32 const base, const struct dpll_params *params,
+				u8 lock, char *dpll)
+{
+	u32 temp, M, N;
+	struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
+
+	if (!params)
+		return;
+
+	temp = readl(&dpll_regs->cm_clksel_dpll);
+
+	if (check_for_lock(base)) {
+		/*
+		 * The Dpll has already been locked by rom code using CH.
+		 * Check if M,N are matching with Ideal nominal opp values.
+		 * If matches, skip the rest otherwise relock.
+		 */
+		M = (temp & CM_CLKSEL_DPLL_M_MASK) >> CM_CLKSEL_DPLL_M_SHIFT;
+		N = (temp & CM_CLKSEL_DPLL_N_MASK) >> CM_CLKSEL_DPLL_N_SHIFT;
+		if ((M != (params->m)) || (N != (params->n))) {
+			debug("\n %s Dpll locked, but not for ideal M = %d,"
+				"N = %d values, current values are M = %d,"
+				"N= %d" , dpll, params->m, params->n,
+				M, N);
+		} else {
+			/* Dpll locked with ideal values for nominal opps. */
+			debug("\n %s Dpll already locked with ideal"
+						"nominal opp values", dpll);
+
+			bypass_dpll(base);
+			goto setup_post_dividers;
+		}
+	}
+
+	bypass_dpll(base);
+
+	/* Set M & N */
+	temp &= ~CM_CLKSEL_DPLL_M_MASK;
+	temp |= (params->m << CM_CLKSEL_DPLL_M_SHIFT) & CM_CLKSEL_DPLL_M_MASK;
+
+	temp &= ~CM_CLKSEL_DPLL_N_MASK;
+	temp |= (params->n << CM_CLKSEL_DPLL_N_SHIFT) & CM_CLKSEL_DPLL_N_MASK;
+
+	writel(temp, &dpll_regs->cm_clksel_dpll);
+
+setup_post_dividers:
+	setup_post_dividers(base, params);
+
+	/* Lock */
+	if (lock)
+		do_lock_dpll(base);
+
+	/* Wait till the DPLL locks */
+	if (lock)
+		wait_for_lock(base);
+}
+
+u32 omap_ddr_clk(void)
+{
+	u32 ddr_clk, sys_clk_khz, omap_rev, divider;
+	const struct dpll_params *core_dpll_params;
+
+	omap_rev = omap_revision();
+	sys_clk_khz = get_sys_clk_freq() / 1000;
+
+	core_dpll_params = get_core_dpll_params(*dplls_data);
+
+	debug("sys_clk %d\n ", sys_clk_khz * 1000);
+
+	/* Find Core DPLL locked frequency first */
+	ddr_clk = sys_clk_khz * 2 * core_dpll_params->m /
+			(core_dpll_params->n + 1);
+
+	if (omap_rev < OMAP5430_ES1_0) {
+		/*
+		 * DDR frequency is PHY_ROOT_CLK/2
+		 * PHY_ROOT_CLK = Fdpll/2/M2
+		 */
+		divider = 4;
+	} else {
+		/*
+		 * DDR frequency is PHY_ROOT_CLK
+		 * PHY_ROOT_CLK = Fdpll/2/M2
+		 */
+		divider = 2;
+	}
+
+	ddr_clk = ddr_clk / divider / core_dpll_params->m2;
+	ddr_clk *= 1000;	/* convert to Hz */
+	debug("ddr_clk %d\n ", ddr_clk);
+
+	return ddr_clk;
+}
+
+/*
+ * Lock MPU dpll
+ *
+ * Resulting MPU frequencies:
+ * 4430 ES1.0	: 600 MHz
+ * 4430 ES2.x	: 792 MHz (OPP Turbo)
+ * 4460		: 920 MHz (OPP Turbo) - DCC disabled
+ */
+void configure_mpu_dpll(void)
+{
+	const struct dpll_params *params;
+	struct dpll_regs *mpu_dpll_regs;
+	u32 omap_rev;
+	omap_rev = omap_revision();
+
+	/*
+	 * DCC and clock divider settings for 4460.
+	 * DCC is required, if more than a certain frequency is required.
+	 * For, 4460 > 1GHZ.
+	 *     5430 > 1.4GHZ.
+	 */
+	if ((omap_rev >= OMAP4460_ES1_0) && (omap_rev < OMAP5430_ES1_0)) {
+		mpu_dpll_regs =
+			(struct dpll_regs *)((*prcm)->cm_clkmode_dpll_mpu);
+		bypass_dpll((*prcm)->cm_clkmode_dpll_mpu);
+		clrbits_le32((*prcm)->cm_mpu_mpu_clkctrl,
+			MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_MASK);
+		setbits_le32((*prcm)->cm_mpu_mpu_clkctrl,
+			MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_MASK);
+		clrbits_le32(&mpu_dpll_regs->cm_clksel_dpll,
+			CM_CLKSEL_DCC_EN_MASK);
+	}
+
+	params = get_mpu_dpll_params(*dplls_data);
+
+	do_setup_dpll((*prcm)->cm_clkmode_dpll_mpu, params, DPLL_LOCK, "mpu");
+	debug("MPU DPLL locked\n");
+}
+
+#if defined(CONFIG_USB_EHCI_OMAP) || defined(CONFIG_USB_XHCI_OMAP) || \
+	defined(CONFIG_USB_MUSB_OMAP2PLUS)
+static void setup_usb_dpll(void)
+{
+	const struct dpll_params *params;
+	u32 sys_clk_khz, sd_div, num, den;
+
+	sys_clk_khz = get_sys_clk_freq() / 1000;
+	/*
+	 * USB:
+	 * USB dpll is J-type. Need to set DPLL_SD_DIV for jitter correction
+	 * DPLL_SD_DIV = CEILING ([DPLL_MULT/(DPLL_DIV+1)]* CLKINP / 250)
+	 *      - where CLKINP is sys_clk in MHz
+	 * Use CLKINP in KHz and adjust the denominator accordingly so
+	 * that we have enough accuracy and at the same time no overflow
+	 */
+	params = get_usb_dpll_params(*dplls_data);
+	num = params->m * sys_clk_khz;
+	den = (params->n + 1) * 250 * 1000;
+	num += den - 1;
+	sd_div = num / den;
+	clrsetbits_le32((*prcm)->cm_clksel_dpll_usb,
+			CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK,
+			sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT);
+
+	/* Now setup the dpll with the regular function */
+	do_setup_dpll((*prcm)->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb");
+}
+#endif
+
+static void setup_dplls(void)
+{
+	u32 temp;
+	const struct dpll_params *params;
+	struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+
+	debug("setup_dplls\n");
+
+	/* CORE dpll */
+	params = get_core_dpll_params(*dplls_data);	/* default - safest */
+	/*
+	 * Do not lock the core DPLL now. Just set it up.
+	 * Core DPLL will be locked after setting up EMIF
+	 * using the FREQ_UPDATE method(freq_update_core())
+	 */
+	if (emif_sdram_type(readl(&emif->emif_sdram_config)) ==
+	    EMIF_SDRAM_TYPE_LPDDR2)
+		do_setup_dpll((*prcm)->cm_clkmode_dpll_core, params,
+							DPLL_NO_LOCK, "core");
+	else
+		do_setup_dpll((*prcm)->cm_clkmode_dpll_core, params,
+							DPLL_LOCK, "core");
+	/* Set the ratios for CORE_CLK, L3_CLK, L4_CLK */
+	temp = (CLKSEL_CORE_X2_DIV_1 << CLKSEL_CORE_SHIFT) |
+	    (CLKSEL_L3_CORE_DIV_2 << CLKSEL_L3_SHIFT) |
+	    (CLKSEL_L4_L3_DIV_2 << CLKSEL_L4_SHIFT);
+	writel(temp, (*prcm)->cm_clksel_core);
+	debug("Core DPLL configured\n");
+
+	/* lock PER dpll */
+	params = get_per_dpll_params(*dplls_data);
+	do_setup_dpll((*prcm)->cm_clkmode_dpll_per,
+			params, DPLL_LOCK, "per");
+	debug("PER DPLL locked\n");
+
+	/* MPU dpll */
+	configure_mpu_dpll();
+
+#if defined(CONFIG_USB_EHCI_OMAP) || defined(CONFIG_USB_XHCI_OMAP) || \
+	defined(CONFIG_USB_MUSB_OMAP2PLUS)
+	setup_usb_dpll();
+#endif
+	params = get_ddr_dpll_params(*dplls_data);
+	do_setup_dpll((*prcm)->cm_clkmode_dpll_ddrphy,
+		      params, DPLL_LOCK, "ddr");
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+	params = get_gmac_dpll_params(*dplls_data);
+	do_setup_dpll((*prcm)->cm_clkmode_dpll_gmac, params,
+		      DPLL_LOCK, "gmac");
+#endif
+}
+
+u32 get_offset_code(u32 volt_offset, struct pmic_data *pmic)
+{
+	u32 offset_code;
+
+	volt_offset -= pmic->base_offset;
+
+	offset_code = (volt_offset + pmic->step - 1) / pmic->step;
+
+	/*
+	 * Offset codes 1-6 all give the base voltage in Palmas
+	 * Offset code 0 switches OFF the SMPS
+	 */
+	return offset_code + pmic->start_code;
+}
+
+void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
+{
+	u32 offset_code;
+	u32 offset = volt_mv;
+	int ret = 0;
+
+	if (!volt_mv)
+		return;
+
+	pmic->pmic_bus_init();
+	/* See if we can first get the GPIO if needed */
+	if (pmic->gpio_en)
+		ret = gpio_request(pmic->gpio, "PMIC_GPIO");
+
+	if (ret < 0) {
+		printf("%s: gpio %d request failed %d\n", __func__,
+							pmic->gpio, ret);
+		return;
+	}
+
+	/* Pull the GPIO low to select SET0 register, while we program SET1 */
+	if (pmic->gpio_en)
+		gpio_direction_output(pmic->gpio, 0);
+
+	/* convert to uV for better accuracy in the calculations */
+	offset *= 1000;
+
+	offset_code = get_offset_code(offset, pmic);
+
+	debug("do_scale_vcore: volt - %d offset_code - 0x%x\n", volt_mv,
+		offset_code);
+
+	if (pmic->pmic_write(pmic->i2c_slave_addr, vcore_reg, offset_code))
+		printf("Scaling voltage failed for 0x%x\n", vcore_reg);
+	if (pmic->gpio_en)
+		gpio_direction_output(pmic->gpio, 1);
+}
+
+static u32 optimize_vcore_voltage(struct volts const *v)
+{
+	u32 val;
+	if (!v->value)
+		return 0;
+	if (!v->efuse.reg)
+		return v->value;
+
+	switch (v->efuse.reg_bits) {
+	case 16:
+		val = readw(v->efuse.reg);
+		break;
+	case 32:
+		val = readl(v->efuse.reg);
+		break;
+	default:
+		printf("Error: efuse 0x%08x bits=%d unknown\n",
+		       v->efuse.reg, v->efuse.reg_bits);
+		return v->value;
+	}
+
+	if (!val) {
+		printf("Error: efuse 0x%08x bits=%d val=0, using %d\n",
+		       v->efuse.reg, v->efuse.reg_bits, v->value);
+		return v->value;
+	}
+
+	debug("%s:efuse 0x%08x bits=%d Vnom=%d, using efuse value %d\n",
+	      __func__, v->efuse.reg, v->efuse.reg_bits, v->value, val);
+	return val;
+}
+
+#ifdef CONFIG_IODELAY_RECALIBRATION
+void __weak recalibrate_iodelay(void)
+{
+}
+#endif
+
+/*
+ * Setup the voltages for the main SoC core power domains.
+ * We start with the maximum voltages allowed here, as set in the corresponding
+ * vcores_data struct, and then scale (usually down) to the fused values that
+ * are retrieved from the SoC. The scaling happens only if the efuse.reg fields
+ * are initialised.
+ * Rail grouping is supported for the DRA7xx SoCs only, therefore the code is
+ * compiled conditionally. Note that the new code writes the scaled (or zeroed)
+ * values back to the vcores_data struct for eventual reuse. Zero values mean
+ * that the corresponding rails are not controlled separately, and are not sent
+ * to the PMIC.
+ */
+void scale_vcores(struct vcores_data const *vcores)
+{
+	int i;
+	struct volts *pv = (struct volts *)vcores;
+	struct volts *px;
+
+	for (i=0; i<(sizeof(struct vcores_data)/sizeof(struct volts)); i++) {
+		debug("%d -> ", pv->value);
+		if (pv->value) {
+			/* Handle non-empty members only */
+			pv->value = optimize_vcore_voltage(pv);
+     			px = (struct volts *)vcores;
+			while (px < pv) {
+				/*
+				 * Scan already handled non-empty members to see
+				 * if we have a group and find the max voltage,
+				 * which is set to the first occurance of the
+				 * particular SMPS; the other group voltages are
+				 * zeroed.
+				 */
+				if (px->value) {
+					if ((pv->pmic->i2c_slave_addr ==
+					     px->pmic->i2c_slave_addr) &&
+					    (pv->addr == px->addr)) {
+					    	/* Same PMIC, same SMPS */
+						if (pv->value > px->value)
+							px->value = pv->value;
+
+						pv->value = 0;
+					}
+		     		}
+				px++;
+			}
+		}
+	     	debug("%d\n", pv->value);
+		pv++;
+	}
+
+	debug("cor: %d\n", vcores->core.value);
+	do_scale_vcore(vcores->core.addr, vcores->core.value, vcores->core.pmic);
+	/*
+	 * IO delay recalibration should be done immediately after
+	 * adjusting AVS voltages for VDD_CORE_L.
+	 * Respective boards should call __recalibrate_iodelay()
+	 * with proper mux, virtual and manual mode configurations.
+	 */
+#ifdef CONFIG_IODELAY_RECALIBRATION
+	recalibrate_iodelay();
+#endif
+
+	debug("mpu: %d\n", vcores->mpu.value);
+	do_scale_vcore(vcores->mpu.addr, vcores->mpu.value, vcores->mpu.pmic);
+	/* Configure MPU ABB LDO after scale */
+	abb_setup(vcores->mpu.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_mpu_voltage_ctrl,
+		  (*prcm)->prm_abbldo_mpu_setup,
+		  (*prcm)->prm_abbldo_mpu_ctrl,
+		  (*prcm)->prm_irqstatus_mpu_2,
+		  vcores->mpu.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
+
+	debug("mm: %d\n", vcores->mm.value);
+	do_scale_vcore(vcores->mm.addr, vcores->mm.value, vcores->mm.pmic);
+	/* Configure MM ABB LDO after scale */
+	abb_setup(vcores->mm.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl,
+		  (*prcm)->prm_abbldo_mm_setup,
+		  (*prcm)->prm_abbldo_mm_ctrl,
+		  (*prcm)->prm_irqstatus_mpu,
+		  vcores->mm.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
+
+	debug("gpu: %d\n", vcores->gpu.value);
+	do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, vcores->gpu.pmic);
+	/* Configure GPU ABB LDO after scale */
+	abb_setup(vcores->gpu.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_gpu_voltage_ctrl,
+		  (*prcm)->prm_abbldo_gpu_setup,
+		  (*prcm)->prm_abbldo_gpu_ctrl,
+		  (*prcm)->prm_irqstatus_mpu,
+		  vcores->gpu.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
+	debug("eve: %d\n", vcores->eve.value);
+	do_scale_vcore(vcores->eve.addr, vcores->eve.value, vcores->eve.pmic);
+	/* Configure EVE ABB LDO after scale */
+	abb_setup(vcores->eve.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_eve_voltage_ctrl,
+		  (*prcm)->prm_abbldo_eve_setup,
+		  (*prcm)->prm_abbldo_eve_ctrl,
+		  (*prcm)->prm_irqstatus_mpu,
+		  vcores->eve.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
+	debug("iva: %d\n", vcores->iva.value);
+	do_scale_vcore(vcores->iva.addr, vcores->iva.value, vcores->iva.pmic);
+	/* Configure IVA ABB LDO after scale */
+	abb_setup(vcores->iva.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_iva_voltage_ctrl,
+		  (*prcm)->prm_abbldo_iva_setup,
+		  (*prcm)->prm_abbldo_iva_ctrl,
+		  (*prcm)->prm_irqstatus_mpu,
+		  vcores->iva.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
+}
+
+static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode)
+{
+	clrsetbits_le32(clkctrl_reg, CD_CLKCTRL_CLKTRCTRL_MASK,
+			enable_mode << CD_CLKCTRL_CLKTRCTRL_SHIFT);
+	debug("Enable clock domain - %x\n", clkctrl_reg);
+}
+
+static inline void disable_clock_domain(u32 const clkctrl_reg)
+{
+	clrsetbits_le32(clkctrl_reg, CD_CLKCTRL_CLKTRCTRL_MASK,
+			CD_CLKCTRL_CLKTRCTRL_SW_SLEEP <<
+			CD_CLKCTRL_CLKTRCTRL_SHIFT);
+	debug("Disable clock domain - %x\n", clkctrl_reg);
+}
+
+static inline void wait_for_clk_enable(u32 clkctrl_addr)
+{
+	u32 clkctrl, idlest = MODULE_CLKCTRL_IDLEST_DISABLED;
+	u32 bound = LDELAY;
+
+	while ((idlest == MODULE_CLKCTRL_IDLEST_DISABLED) ||
+		(idlest == MODULE_CLKCTRL_IDLEST_TRANSITIONING)) {
+
+		clkctrl = readl(clkctrl_addr);
+		idlest = (clkctrl & MODULE_CLKCTRL_IDLEST_MASK) >>
+			 MODULE_CLKCTRL_IDLEST_SHIFT;
+		if (--bound == 0) {
+			printf("Clock enable failed for 0x%x idlest 0x%x\n",
+				clkctrl_addr, clkctrl);
+			return;
+		}
+	}
+}
+
+static inline void enable_clock_module(u32 const clkctrl_addr, u32 enable_mode,
+				u32 wait_for_enable)
+{
+	clrsetbits_le32(clkctrl_addr, MODULE_CLKCTRL_MODULEMODE_MASK,
+			enable_mode << MODULE_CLKCTRL_MODULEMODE_SHIFT);
+	debug("Enable clock module - %x\n", clkctrl_addr);
+	if (wait_for_enable)
+		wait_for_clk_enable(clkctrl_addr);
+}
+
+static inline void wait_for_clk_disable(u32 clkctrl_addr)
+{
+	u32 clkctrl, idlest = MODULE_CLKCTRL_IDLEST_FULLY_FUNCTIONAL;
+	u32 bound = LDELAY;
+
+	while ((idlest != MODULE_CLKCTRL_IDLEST_DISABLED)) {
+		clkctrl = readl(clkctrl_addr);
+		idlest = (clkctrl & MODULE_CLKCTRL_IDLEST_MASK) >>
+			 MODULE_CLKCTRL_IDLEST_SHIFT;
+		if (--bound == 0) {
+			printf("Clock disable failed for 0x%x idlest 0x%x\n",
+			       clkctrl_addr, clkctrl);
+			return;
+		}
+	}
+}
+
+static inline void disable_clock_module(u32 const clkctrl_addr,
+					u32 wait_for_disable)
+{
+	clrsetbits_le32(clkctrl_addr, MODULE_CLKCTRL_MODULEMODE_MASK,
+			MODULE_CLKCTRL_MODULEMODE_SW_DISABLE <<
+			MODULE_CLKCTRL_MODULEMODE_SHIFT);
+	debug("Disable clock module - %x\n", clkctrl_addr);
+	if (wait_for_disable)
+		wait_for_clk_disable(clkctrl_addr);
+}
+
+void freq_update_core(void)
+{
+	u32 freq_config1 = 0;
+	const struct dpll_params *core_dpll_params;
+	u32 omap_rev = omap_revision();
+
+	core_dpll_params = get_core_dpll_params(*dplls_data);
+	/* Put EMIF clock domain in sw wakeup mode */
+	enable_clock_domain((*prcm)->cm_memif_clkstctrl,
+				CD_CLKCTRL_CLKTRCTRL_SW_WKUP);
+	wait_for_clk_enable((*prcm)->cm_memif_emif_1_clkctrl);
+	wait_for_clk_enable((*prcm)->cm_memif_emif_2_clkctrl);
+
+	freq_config1 = SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK |
+	    SHADOW_FREQ_CONFIG1_DLL_RESET_MASK;
+
+	freq_config1 |= (DPLL_EN_LOCK << SHADOW_FREQ_CONFIG1_DPLL_EN_SHIFT) &
+				SHADOW_FREQ_CONFIG1_DPLL_EN_MASK;
+
+	freq_config1 |= (core_dpll_params->m2 <<
+			SHADOW_FREQ_CONFIG1_M2_DIV_SHIFT) &
+			SHADOW_FREQ_CONFIG1_M2_DIV_MASK;
+
+	writel(freq_config1, (*prcm)->cm_shadow_freq_config1);
+	if (!wait_on_value(SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK, 0,
+			(u32 *) (*prcm)->cm_shadow_freq_config1, LDELAY)) {
+		puts("FREQ UPDATE procedure failed!!");
+		hang();
+	}
+
+	/*
+	 * Putting EMIF in HW_AUTO is seen to be causing issues with
+	 * EMIF clocks and the master DLL. Keep EMIF in SW_WKUP
+	 * in OMAP5430 ES1.0 silicon
+	 */
+	if (omap_rev != OMAP5430_ES1_0) {
+		/* Put EMIF clock domain back in hw auto mode */
+		enable_clock_domain((*prcm)->cm_memif_clkstctrl,
+					CD_CLKCTRL_CLKTRCTRL_HW_AUTO);
+		wait_for_clk_enable((*prcm)->cm_memif_emif_1_clkctrl);
+		wait_for_clk_enable((*prcm)->cm_memif_emif_2_clkctrl);
+	}
+}
+
+void bypass_dpll(u32 const base)
+{
+	do_bypass_dpll(base);
+	wait_for_bypass(base);
+}
+
+void lock_dpll(u32 const base)
+{
+	do_lock_dpll(base);
+	wait_for_lock(base);
+}
+
+static void setup_clocks_for_console(void)
+{
+	/* Do not add any spl_debug prints in this function */
+	clrsetbits_le32((*prcm)->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
+			CD_CLKCTRL_CLKTRCTRL_SW_WKUP <<
+			CD_CLKCTRL_CLKTRCTRL_SHIFT);
+
+	/* Enable all UARTs - console will be on one of them */
+	clrsetbits_le32((*prcm)->cm_l4per_uart1_clkctrl,
+			MODULE_CLKCTRL_MODULEMODE_MASK,
+			MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
+			MODULE_CLKCTRL_MODULEMODE_SHIFT);
+
+	clrsetbits_le32((*prcm)->cm_l4per_uart2_clkctrl,
+			MODULE_CLKCTRL_MODULEMODE_MASK,
+			MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
+			MODULE_CLKCTRL_MODULEMODE_SHIFT);
+
+	clrsetbits_le32((*prcm)->cm_l4per_uart3_clkctrl,
+			MODULE_CLKCTRL_MODULEMODE_MASK,
+			MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
+			MODULE_CLKCTRL_MODULEMODE_SHIFT);
+
+	clrsetbits_le32((*prcm)->cm_l4per_uart4_clkctrl,
+			MODULE_CLKCTRL_MODULEMODE_MASK,
+			MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
+			MODULE_CLKCTRL_MODULEMODE_SHIFT);
+
+	clrsetbits_le32((*prcm)->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
+			CD_CLKCTRL_CLKTRCTRL_HW_AUTO <<
+			CD_CLKCTRL_CLKTRCTRL_SHIFT);
+}
+
+void do_enable_clocks(u32 const *clk_domains,
+			    u32 const *clk_modules_hw_auto,
+			    u32 const *clk_modules_explicit_en,
+			    u8 wait_for_enable)
+{
+	u32 i, max = 100;
+
+	/* Put the clock domains in SW_WKUP mode */
+	for (i = 0; (i < max) && clk_domains[i]; i++) {
+		enable_clock_domain(clk_domains[i],
+				    CD_CLKCTRL_CLKTRCTRL_SW_WKUP);
+	}
+
+	/* Clock modules that need to be put in HW_AUTO */
+	for (i = 0; (i < max) && clk_modules_hw_auto[i]; i++) {
+		enable_clock_module(clk_modules_hw_auto[i],
+				    MODULE_CLKCTRL_MODULEMODE_HW_AUTO,
+				    wait_for_enable);
+	};
+
+	/* Clock modules that need to be put in SW_EXPLICIT_EN mode */
+	for (i = 0; (i < max) && clk_modules_explicit_en[i]; i++) {
+		enable_clock_module(clk_modules_explicit_en[i],
+				    MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN,
+				    wait_for_enable);
+	};
+
+	/* Put the clock domains in HW_AUTO mode now */
+	for (i = 0; (i < max) && clk_domains[i]; i++) {
+		enable_clock_domain(clk_domains[i],
+				    CD_CLKCTRL_CLKTRCTRL_HW_AUTO);
+	}
+}
+
+void do_disable_clocks(u32 const *clk_domains,
+			    u32 const *clk_modules_disable,
+			    u8 wait_for_disable)
+{
+	u32 i, max = 100;
+
+
+	/* Clock modules that need to be put in SW_DISABLE */
+	for (i = 0; (i < max) && clk_modules_disable[i]; i++)
+		disable_clock_module(clk_modules_disable[i],
+				     wait_for_disable);
+
+	/* Put the clock domains in SW_SLEEP mode */
+	for (i = 0; (i < max) && clk_domains[i]; i++)
+		disable_clock_domain(clk_domains[i]);
+}
+
+/**
+ * setup_early_clocks() - Setup early clocks needed for SoC
+ *
+ * Setup clocks for console, SPL basic initialization clocks and initialize
+ * the timer. This is invoked prior prcm_init.
+ */
+void setup_early_clocks(void)
+{
+	switch (omap_hw_init_context()) {
+	case OMAP_INIT_CONTEXT_SPL:
+	case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
+	case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
+		setup_clocks_for_console();
+		enable_basic_clocks();
+		timer_init();
+		/* Fall through */
+	}
+}
+
+void prcm_init(void)
+{
+	switch (omap_hw_init_context()) {
+	case OMAP_INIT_CONTEXT_SPL:
+	case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
+	case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
+		scale_vcores(*omap_vcores);
+		setup_dplls();
+		setup_warmreset_time();
+		break;
+	default:
+		break;
+	}
+
+	if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context())
+		enable_basic_uboot_clocks();
+}
+
+void gpi2c_init(void)
+{
+	static int gpi2c = 1;
+
+	if (gpi2c) {
+		i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED,
+			 CONFIG_SYS_OMAP24_I2C_SLAVE);
+		gpi2c = 0;
+	}
+}