diff options
Diffstat (limited to 'arch/blackfin/cpu/serial1.h')
| -rw-r--r-- | arch/blackfin/cpu/serial1.h | 348 |
1 files changed, 348 insertions, 0 deletions
diff --git a/arch/blackfin/cpu/serial1.h b/arch/blackfin/cpu/serial1.h new file mode 100644 index 0000000000..a20175bc7f --- /dev/null +++ b/arch/blackfin/cpu/serial1.h @@ -0,0 +1,348 @@ +/* + * serial.h - common serial defines for early debug and serial driver. + * any functions defined here must be always_inline since + * initcode cannot have function calls. + * + * Copyright (c) 2004-2011 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#ifndef __BFIN_CPU_SERIAL1_H__ +#define __BFIN_CPU_SERIAL1_H__ + +#include <asm/mach-common/bits/uart.h> + +#ifndef __ASSEMBLY__ + +#define MMR_UART(n) _PASTE_UART(n, UART, DLL) +#ifdef UART_DLL +# define UART0_DLL UART_DLL +# if CONFIG_UART_CONSOLE != 0 +# error CONFIG_UART_CONSOLE must be 0 on parts with only one UART +# endif +#endif +#define UART_BASE MMR_UART(CONFIG_UART_CONSOLE) + +#define LOB(x) ((x) & 0xFF) +#define HIB(x) (((x) >> 8) & 0xFF) + +/* + * All Blackfin system MMRs are padded to 32bits even if the register + * itself is only 16bits. So use a helper macro to streamline this. + */ +struct bfin_mmr_serial { +#if BFIN_UART_HW_VER == 2 + u16 dll; + u16 __pad_0; + u16 dlh; + u16 __pad_1; + u16 gctl; + u16 __pad_2; + u16 lcr; + u16 __pad_3; + u16 mcr; + u16 __pad_4; + u16 lsr; + u16 __pad_5; + u16 msr; + u16 __pad_6; + u16 scr; + u16 __pad_7; + u16 ier_set; + u16 __pad_8; + u16 ier_clear; + u16 __pad_9; + u16 thr; + u16 __pad_10; + u16 rbr; + u16 __pad_11; +#else + union { + u16 dll; + u16 thr; + const u16 rbr; + }; + const u16 __spad0; + union { + u16 dlh; + u16 ier; + }; + const u16 __spad1; + const u16 iir; + u16 __pad_0; + u16 lcr; + u16 __pad_1; + u16 mcr; + u16 __pad_2; + u16 lsr; + u16 __pad_3; + u16 msr; + u16 __pad_4; + u16 scr; + u16 __pad_5; + const u32 __spad2; + u16 gctl; + u16 __pad_6; +#endif +}; + +#define uart_lsr_t uint32_t +#define _lsr_read(p) bfin_read(&p->lsr) +#define _lsr_write(p, v) bfin_write(&p->lsr, v) + +#if BFIN_UART_HW_VER == 2 +# define ACCESS_LATCH() +# define ACCESS_PORT_IER() +#else +# define ACCESS_LATCH() bfin_write_or(&pUART->lcr, DLAB) +# define ACCESS_PORT_IER() bfin_write_and(&pUART->lcr, ~DLAB) +#endif + +__attribute__((always_inline)) +static inline void serial_early_do_mach_portmux(char port, int mux_mask, + int mux_func, int port_pin) +{ + switch (port) { +#if defined(__ADSPBF54x__) + case 'B': + bfin_write_PORTB_MUX((bfin_read_PORTB_MUX() & + ~mux_mask) | mux_func); + bfin_write_PORTB_FER(bfin_read_PORTB_FER() | port_pin); + break; + case 'E': + bfin_write_PORTE_MUX((bfin_read_PORTE_MUX() & + ~mux_mask) | mux_func); + bfin_write_PORTE_FER(bfin_read_PORTE_FER() | port_pin); + break; +#endif +#if defined(__ADSPBF50x__) || defined(__ADSPBF51x__) || defined(__ADSPBF52x__) + case 'F': + bfin_write_PORTF_MUX((bfin_read_PORTF_MUX() & + ~mux_mask) | mux_func); + bfin_write_PORTF_FER(bfin_read_PORTF_FER() | port_pin); + break; + case 'G': + bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & + ~mux_mask) | mux_func); + bfin_write_PORTG_FER(bfin_read_PORTG_FER() | port_pin); + break; + case 'H': + bfin_write_PORTH_MUX((bfin_read_PORTH_MUX() & + ~mux_mask) | mux_func); + bfin_write_PORTH_FER(bfin_read_PORTH_FER() | port_pin); + break; +#endif + default: + break; + } +} + +__attribute__((always_inline)) +static inline void serial_early_do_portmux(void) +{ +#if defined(__ADSPBF50x__) + switch (CONFIG_UART_CONSOLE) { + case 0: + serial_early_do_mach_portmux('G', PORT_x_MUX_7_MASK, + PORT_x_MUX_7_FUNC_1, PG12); /* TX: G; mux 7; func 1; PG12 */ + serial_early_do_mach_portmux('G', PORT_x_MUX_7_MASK, + PORT_x_MUX_7_FUNC_1, PG13); /* RX: G; mux 7; func 1; PG13 */ + break; + case 1: + serial_early_do_mach_portmux('F', PORT_x_MUX_3_MASK, + PORT_x_MUX_3_FUNC_1, PF7); /* TX: F; mux 3; func 1; PF6 */ + serial_early_do_mach_portmux('F', PORT_x_MUX_3_MASK, + PORT_x_MUX_3_FUNC_1, PF6); /* RX: F; mux 3; func 1; PF7 */ + break; + } +#elif defined(__ADSPBF51x__) + switch (CONFIG_UART_CONSOLE) { + case 0: + serial_early_do_mach_portmux('G', PORT_x_MUX_5_MASK, + PORT_x_MUX_5_FUNC_2, PG9); /* TX: G; mux 5; func 2; PG9 */ + serial_early_do_mach_portmux('G', PORT_x_MUX_5_MASK, + PORT_x_MUX_5_FUNC_2, PG10); /* RX: G; mux 5; func 2; PG10 */ + break; + case 1: + serial_early_do_mach_portmux('H', PORT_x_MUX_3_MASK, + PORT_x_MUX_3_FUNC_2, PH7); /* TX: H; mux 3; func 2; PH6 */ + serial_early_do_mach_portmux('H', PORT_x_MUX_3_MASK, + PORT_x_MUX_3_FUNC_2, PH6); /* RX: H; mux 3; func 2; PH7 */ + break; + } +#elif defined(__ADSPBF52x__) + switch (CONFIG_UART_CONSOLE) { + case 0: + serial_early_do_mach_portmux('G', PORT_x_MUX_2_MASK, + PORT_x_MUX_2_FUNC_3, PG7); /* TX: G; mux 2; func 3; PG7 */ + serial_early_do_mach_portmux('G', PORT_x_MUX_2_MASK, + PORT_x_MUX_2_FUNC_3, PG8); /* RX: G; mux 2; func 3; PG8 */ + break; + case 1: + serial_early_do_mach_portmux('F', PORT_x_MUX_5_MASK, + PORT_x_MUX_5_FUNC_3, PF14); /* TX: F; mux 5; func 3; PF14 */ + serial_early_do_mach_portmux('F', PORT_x_MUX_5_MASK, + PORT_x_MUX_5_FUNC_3, PF15); /* RX: F; mux 5; func 3; PF15 */ + break; + } +#elif defined(__ADSPBF537__) || defined(__ADSPBF536__) || defined(__ADSPBF534__) + const uint16_t func[] = { PFDE, PFTE, }; + bfin_write_PORT_MUX(bfin_read_PORT_MUX() & ~func[CONFIG_UART_CONSOLE]); + bfin_write_PORTF_FER(bfin_read_PORTF_FER() | + (1 << P_IDENT(P_UART(RX))) | + (1 << P_IDENT(P_UART(TX)))); +#elif defined(__ADSPBF54x__) + switch (CONFIG_UART_CONSOLE) { + case 0: + serial_early_do_mach_portmux('E', PORT_x_MUX_7_MASK, + PORT_x_MUX_7_FUNC_1, PE7); /* TX: E; mux 7; func 1; PE7 */ + serial_early_do_mach_portmux('E', PORT_x_MUX_8_MASK, + PORT_x_MUX_8_FUNC_1, PE8); /* RX: E; mux 8; func 1; PE8 */ + break; + case 1: + serial_early_do_mach_portmux('H', PORT_x_MUX_0_MASK, + PORT_x_MUX_0_FUNC_1, PH0); /* TX: H; mux 0; func 1; PH0 */ + serial_early_do_mach_portmux('H', PORT_x_MUX_1_MASK, + PORT_x_MUX_1_FUNC_1, PH1); /* RX: H; mux 1; func 1; PH1 */ + break; + case 2: + serial_early_do_mach_portmux('B', PORT_x_MUX_4_MASK, + PORT_x_MUX_4_FUNC_1, PB4); /* TX: B; mux 4; func 1; PB4 */ + serial_early_do_mach_portmux('B', PORT_x_MUX_5_MASK, + PORT_x_MUX_5_FUNC_1, PB5); /* RX: B; mux 5; func 1; PB5 */ + break; + case 3: + serial_early_do_mach_portmux('B', PORT_x_MUX_6_MASK, + PORT_x_MUX_6_FUNC_1, PB6); /* TX: B; mux 6; func 1; PB6 */ + serial_early_do_mach_portmux('B', PORT_x_MUX_7_MASK, + PORT_x_MUX_7_FUNC_1, PB7); /* RX: B; mux 7; func 1; PB7 */ + break; + } +#elif defined(__ADSPBF561__) + /* UART pins could be GPIO, but they aren't pin muxed. */ +#else +# if (P_UART(RX) & P_DEFINED) || (P_UART(TX) & P_DEFINED) +# error "missing portmux logic for UART" +# endif +#endif + SSYNC(); +} + +__attribute__((always_inline)) +static inline uint32_t uart_sclk(void) +{ +#if defined(BFIN_IN_INITCODE) || defined(CONFIG_DEBUG_EARLY_SERIAL) + /* We cannot use get_sclk() early on as it uses + * caches in external memory + */ + return CONFIG_CLKIN_HZ * CONFIG_VCO_MULT / CONFIG_SCLK_DIV; +#else + return get_sclk(); +#endif +} + +__attribute__((always_inline)) +static inline int uart_init(uint32_t uart_base) +{ + /* always enable UART -- avoids anomalies 05000309 and 05000350 */ + bfin_write(&pUART->gctl, UCEN); + + /* Set LCR to Word Lengh 8-bit word select */ + bfin_write(&pUART->lcr, WLS_8); + + SSYNC(); + + return 0; +} + +__attribute__((always_inline)) +static inline int serial_early_init(uint32_t uart_base) +{ + /* handle portmux crap on different Blackfins */ + serial_do_portmux(); + + return uart_init(uart_base); +} + +__attribute__((always_inline)) +static inline int serial_early_uninit(uint32_t uart_base) +{ + /* disable the UART by clearing UCEN */ + bfin_write(&pUART->gctl, 0); + + return 0; +} + +__attribute__((always_inline)) +static inline int serial_early_enabled(uint32_t uart_base) +{ + return bfin_read(&pUART->gctl) & UCEN; +} + +__attribute__((always_inline)) +static inline void serial_early_set_baud(uint32_t uart_base, uint32_t baud) +{ + /* Translate from baud into divisor in terms of SCLK. The + * weird multiplication is to make sure we over sample just + * a little rather than under sample the incoming signals. + */ + uint16_t divisor = (uart_sclk() + (baud * 8)) / (baud * 16) - + ANOMALY_05000230; + + /* Set DLAB in LCR to Access DLL and DLH */ + ACCESS_LATCH(); + SSYNC(); + + /* Program the divisor to get the baud rate we want */ + bfin_write(&pUART->dll, LOB(divisor)); + bfin_write(&pUART->dlh, HIB(divisor)); + SSYNC(); + + /* Clear DLAB in LCR to Access THR RBR IER */ + ACCESS_PORT_IER(); + SSYNC(); +} + +__attribute__((always_inline)) +static inline void serial_early_put_div(uint16_t divisor) +{ + uint32_t uart_base = UART_BASE; + + /* Set DLAB in LCR to Access DLL and DLH */ + ACCESS_LATCH(); + SSYNC(); + + /* Program the divisor to get the baud rate we want */ + bfin_write(&pUART->dll, LOB(divisor)); + bfin_write(&pUART->dlh, HIB(divisor)); + SSYNC(); + + /* Clear DLAB in LCR to Access THR RBR IER */ + ACCESS_PORT_IER(); + SSYNC(); +} + +__attribute__((always_inline)) +static inline uint16_t serial_early_get_div(void) +{ + uint32_t uart_base = UART_BASE; + + /* Set DLAB in LCR to Access DLL and DLH */ + ACCESS_LATCH(); + SSYNC(); + + uint8_t dll = bfin_read(&pUART->dll); + uint8_t dlh = bfin_read(&pUART->dlh); + uint16_t divisor = (dlh << 8) | dll; + + /* Clear DLAB in LCR to Access THR RBR IER */ + ACCESS_PORT_IER(); + SSYNC(); + + return divisor; +} + +#endif + +#endif |