diff options
Diffstat (limited to 'arch/mips/cpu/mips64/start.S')
| -rw-r--r-- | arch/mips/cpu/mips64/start.S | 264 |
1 files changed, 0 insertions, 264 deletions
diff --git a/arch/mips/cpu/mips64/start.S b/arch/mips/cpu/mips64/start.S deleted file mode 100644 index 6ff714e8ed..0000000000 --- a/arch/mips/cpu/mips64/start.S +++ /dev/null @@ -1,264 +0,0 @@ -/* - * Startup Code for MIPS64 CPU-core - * - * Copyright (c) 2003 Wolfgang Denk <wd@denx.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <asm-offsets.h> -#include <config.h> -#include <asm/regdef.h> -#include <asm/mipsregs.h> - -#ifndef CONFIG_SYS_MIPS_CACHE_MODE -#define CONFIG_SYS_MIPS_CACHE_MODE CONF_CM_CACHABLE_NONCOHERENT -#endif - -#ifdef CONFIG_SYS_LITTLE_ENDIAN -#define MIPS64_R_INFO(ssym, r_type3, r_type2, r_type) \ - (((r_type) << 24) | ((r_type2) << 16) | ((r_type3) << 8) | (ssym)) -#else -#define MIPS64_R_INFO(ssym, r_type3, r_type2, r_type) \ - ((r_type) | ((r_type2) << 8) | ((r_type3) << 16) | (ssym) << 24) -#endif - - /* - * For the moment disable interrupts, mark the kernel mode and - * set ST0_KX so that the CPU does not spit fire when using - * 64-bit addresses. - */ - .macro setup_c0_status set clr - .set push - mfc0 t0, CP0_STATUS - or t0, ST0_CU0 | \set | 0x1f | \clr - xor t0, 0x1f | \clr - mtc0 t0, CP0_STATUS - .set noreorder - sll zero, 3 # ehb - .set pop - .endm - - .set noreorder - - .globl _start - .text -_start: - /* U-boot entry point */ - b reset - nop - - .org 0x200 - /* TLB refill, 32 bit task */ -1: b 1b - nop - - .org 0x280 - /* XTLB refill, 64 bit task */ -1: b 1b - nop - - .org 0x300 - /* Cache error exception */ -1: b 1b - nop - - .org 0x380 - /* General exception */ -1: b 1b - nop - - .org 0x400 - /* Catch interrupt exceptions */ -1: b 1b - nop - - .org 0x480 - /* EJTAG debug exception */ -1: b 1b - nop - - .align 4 -reset: - - /* Clear watch registers */ - dmtc0 zero, CP0_WATCHLO - dmtc0 zero, CP0_WATCHHI - - /* WP(Watch Pending), SW0/1 should be cleared */ - mtc0 zero, CP0_CAUSE - - setup_c0_status ST0_KX 0 - - /* Init Timer */ - mtc0 zero, CP0_COUNT - mtc0 zero, CP0_COMPARE - -#ifndef CONFIG_SKIP_LOWLEVEL_INIT - /* CONFIG0 register */ - dli t0, CONF_CM_UNCACHED - mtc0 t0, CP0_CONFIG -#endif - - /* - * Initialize $gp, force 8 byte alignment of bal instruction to forbid - * the compiler to put nop's between bal and _gp. This is required to - * keep _gp and ra aligned to 8 byte. - */ - .align 3 - bal 1f - nop - .dword _gp -1: - ld gp, 0(ra) - -#ifndef CONFIG_SKIP_LOWLEVEL_INIT - /* Initialize any external memory */ - dla t9, lowlevel_init - jalr t9 - nop - - /* Initialize caches... */ - dla t9, mips_cache_reset - jalr t9 - nop - - /* ... and enable them */ - dli t0, CONFIG_SYS_MIPS_CACHE_MODE - mtc0 t0, CP0_CONFIG -#endif - - /* Set up temporary stack */ - dli sp, CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_INIT_SP_OFFSET - move fp, sp - - dla t9, board_init_f - jr t9 - move ra, zero - -/* - * void relocate_code (addr_sp, gd, addr_moni) - * - * This "function" does not return, instead it continues in RAM - * after relocating the monitor code. - * - * a0 = addr_sp - * a1 = gd - * a2 = destination address - */ - .globl relocate_code - .ent relocate_code -relocate_code: - move sp, a0 # set new stack pointer - move fp, sp - - move s0, a1 # save gd in s0 - move s2, a2 # save destination address in s2 - - dli t0, CONFIG_SYS_MONITOR_BASE - dsub s1, s2, t0 # s1 <-- relocation offset - - dla t3, in_ram - ld t2, -24(t3) # t2 <-- __image_copy_end - move t1, a2 - - dadd gp, s1 # adjust gp - - /* - * t0 = source address - * t1 = target address - * t2 = source end address - */ -1: - lw t3, 0(t0) - sw t3, 0(t1) - daddu t0, 4 - blt t0, t2, 1b - daddu t1, 4 - - /* If caches were enabled, we would have to flush them here. */ - dsub a1, t1, s2 # a1 <-- size - dla t9, flush_cache - jalr t9 - move a0, s2 # a0 <-- destination address - - /* Jump to where we've relocated ourselves */ - daddi t0, s2, in_ram - _start - jr t0 - nop - - .dword __rel_dyn_end - .dword __rel_dyn_start - .dword __image_copy_end - .dword _GLOBAL_OFFSET_TABLE_ - .dword num_got_entries - -in_ram: - /* - * Now we want to update GOT. - * - * GOT[0] is reserved. GOT[1] is also reserved for the dynamic object - * generated by GNU ld. Skip these reserved entries from relocation. - */ - ld t3, -8(t0) # t3 <-- num_got_entries - ld t8, -16(t0) # t8 <-- _GLOBAL_OFFSET_TABLE_ - dadd t8, s1 # t8 now holds relocated _G_O_T_ - daddi t8, t8, 16 # skipping first two entries - dli t2, 2 -1: - ld t1, 0(t8) - beqz t1, 2f - dadd t1, s1 - sd t1, 0(t8) -2: - daddi t2, 1 - blt t2, t3, 1b - daddi t8, 8 - - /* Update dynamic relocations */ - ld t1, -32(t0) # t1 <-- __rel_dyn_start - ld t2, -40(t0) # t2 <-- __rel_dyn_end - - b 2f # skip first reserved entry - daddi t1, 16 - -1: - lw t8, -4(t1) # t8 <-- relocation info - - dli t3, MIPS64_R_INFO(0x00, 0x00, 0x12, 0x03) - bne t8, t3, 2f # skip non R_MIPS_REL32 entries - nop - - ld t3, -16(t1) # t3 <-- location to fix up in FLASH - - ld t8, 0(t3) # t8 <-- original pointer - dadd t8, s1 # t8 <-- adjusted pointer - - dadd t3, s1 # t3 <-- location to fix up in RAM - sd t8, 0(t3) - -2: - blt t1, t2, 1b - daddi t1, 16 # each rel.dyn entry is 16 bytes - - /* - * Clear BSS - * - * GOT is now relocated. Thus __bss_start and __bss_end can be - * accessed directly via $gp. - */ - dla t1, __bss_start # t1 <-- __bss_start - dla t2, __bss_end # t2 <-- __bss_end - -1: - sd zero, 0(t1) - blt t1, t2, 1b - daddi t1, 8 - - move a0, s0 # a0 <-- gd - move a1, s2 - dla t9, board_init_r - jr t9 - move ra, zero - - .end relocate_code |