3 files changed, 1 insertions, 44 deletions
diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
index f1dca90eba..171bee9f28 100644
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ b/arch/powerpc/cpu/mpc8xx/Kconfig
@@ -16,9 +16,6 @@ config TARGET_ESTEEM192E
 config TARGET_HERMES
 	bool "Support hermes"
 
-config TARGET_ICU862
-	bool "Support ICU862"
-
 config TARGET_IP860
 	bool "Support IP860"
 
@@ -124,7 +121,6 @@ source "board/eltec/mhpc/Kconfig"
 source "board/emk/top860/Kconfig"
 source "board/esteem192e/Kconfig"
 source "board/hermes/Kconfig"
-source "board/icu862/Kconfig"
 source "board/ip860/Kconfig"
 source "board/ivm/Kconfig"
 source "board/kup/kup4k/Kconfig"
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index 90c7e61d83..b8dc14dd14 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -126,7 +126,6 @@ void cpu_init_f (volatile immap_t * immr)
 	 */
 
 #if defined(CONFIG_HERMES)	|| \
-    defined(CONFIG_ICU862)	|| \
     defined(CONFIG_IP860)	|| \
     defined(CONFIG_IVML24)	|| \
     defined(CONFIG_IVMS8)	|| \
diff --git a/arch/powerpc/cpu/mpc8xx/fec.c b/arch/powerpc/cpu/mpc8xx/fec.c
index d12b3df4a1..22b8ec752b 100644
--- a/arch/powerpc/cpu/mpc8xx/fec.c
+++ b/arch/powerpc/cpu/mpc8xx/fec.c
@@ -205,11 +205,7 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
 
 	j = 0;
 	while ((rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY) && (j<TOUT_LOOP)) {
-#if defined(CONFIG_ICU862)
-		udelay(10);
-#else
 		udelay(1);
-#endif
 		j++;
 	}
 	if (j>=TOUT_LOOP) {
@@ -424,7 +420,7 @@ static void fec_pin_init(int fecidx)
 
 #endif /* !CONFIG_RMII */
 
-#elif !defined(CONFIG_ICU862)
+#else
 		/*
 		 * Configure all of port D for MII.
 		 */
@@ -437,42 +433,8 @@ static void fec_pin_init(int fecidx)
 			immr->im_ioport.iop_pddir = 0x1c58;	/* Pre rev. D */
 		else
 			immr->im_ioport.iop_pddir = 0x1fff;	/* Rev. D and later */
-#else
-		/*
-		 * Configure port A for MII.
-		 */
-
-#if defined(CONFIG_ICU862) && defined(CONFIG_SYS_DISCOVER_PHY)
-
-		/*
-		 * On the ICU862 board the MII-MDC pin is routed to PD8 pin
-		 * * of CPU, so for this board we need to configure Utopia and
-		 * * enable PD8 to MII-MDC function
-		 */
-		immr->im_ioport.iop_pdpar |= 0x4080;
 #endif
 
-		/*
-		 * Has Utopia been configured?
-		 */
-		if (immr->im_ioport.iop_pdpar & (0x8000 >> 1)) {
-			/*
-			 * YES - Use MUXED mode for UTOPIA bus.
-			 * This frees Port A for use by MII (see 862UM table 41-6).
-			 */
-			immr->im_ioport.utmode &= ~0x80;
-		} else {
-			/*
-			 * NO - set SPLIT mode for UTOPIA bus.
-			 *
-			 * This doesn't really effect UTOPIA (which isn't
-			 * enabled anyway) but just tells the 862
-			 * to use port A for MII (see 862UM table 41-6).
-			 */
-			immr->im_ioport.utmode |= 0x80;
-		}
-#endif				/* !defined(CONFIG_ICU862) */
-
 #endif	/* CONFIG_ETHER_ON_FEC1 */
 	} else if (fecidx == 1) {