diff options
Diffstat (limited to 'board/CarMediaLab/flea3/flea3.c')
-rw-r--r-- | board/CarMediaLab/flea3/flea3.c | 124 |
1 files changed, 34 insertions, 90 deletions
diff --git a/board/CarMediaLab/flea3/flea3.c b/board/CarMediaLab/flea3/flea3.c index 2463077475..3cd4dc95fe 100644 --- a/board/CarMediaLab/flea3/flea3.c +++ b/board/CarMediaLab/flea3/flea3.c @@ -19,6 +19,9 @@ #include <asm/gpio.h> #include <asm/arch/sys_proto.h> #include <netdev.h> +#include <fdt_support.h> +#include <mtd_node.h> +#include <jffs2/load_kernel.h> #ifndef CONFIG_BOARD_EARLY_INIT_F #error "CONFIG_BOARD_EARLY_INIT_F must be set for this board" @@ -27,18 +30,6 @@ #define CCM_CCMR_CONFIG 0x003F4208 #define ESDCTL_DDR2_CONFIG 0x007FFC3F -#define ESDCTL_0x92220000 0x92220000 -#define ESDCTL_0xA2220000 0xA2220000 -#define ESDCTL_0xB2220000 0xB2220000 -#define ESDCTL_0x82228080 0x82228080 -#define ESDCTL_DDR2_EMR2 0x04000000 -#define ESDCTL_DDR2_EMR3 0x06000000 -#define ESDCTL_PRECHARGE 0x00000400 -#define ESDCTL_DDR2_EN_DLL 0x02000400 -#define ESDCTL_DDR2_RESET_DLL 0x00000333 -#define ESDCTL_DDR2_MR 0x00000233 -#define ESDCTL_DDR2_OCD_DEFAULT 0x02000780 -#define ESDCTL_DELAY_LINE5 0x00F49F00 static inline void dram_wait(unsigned int count) { @@ -58,83 +49,6 @@ int dram_init(void) return 0; } -static void board_setup_sdram_bank(u32 start_address) - -{ - struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR; - u32 *cfg_reg, *ctl_reg; - u32 val; - - switch (start_address) { - case CSD0_BASE_ADDR: - cfg_reg = &esdc->esdcfg0; - ctl_reg = &esdc->esdctl0; - break; - case CSD1_BASE_ADDR: - cfg_reg = &esdc->esdcfg1; - ctl_reg = &esdc->esdctl1; - break; - default: - return; - } - - /* Initialize MISC register for DDR2 */ - val = ESDC_MISC_RST | ESDC_MISC_MDDR_EN | ESDC_MISC_MDDR_DL_RST | - ESDC_MISC_DDR_EN | ESDC_MISC_DDR2_EN; - writel(val, &esdc->esdmisc); - val &= ~(ESDC_MISC_RST | ESDC_MISC_MDDR_DL_RST); - writel(val, &esdc->esdmisc); - - /* - * according to DDR2 specs, wait a while before - * the PRECHARGE_ALL command - */ - dram_wait(0x20000); - - /* Load DDR2 config and timing */ - writel(ESDCTL_DDR2_CONFIG, cfg_reg); - - /* Precharge ALL */ - writel(ESDCTL_0x92220000, - ctl_reg); - writel(0xda, start_address + ESDCTL_PRECHARGE); - - /* Load mode */ - writel(ESDCTL_0xB2220000, - ctl_reg); - writeb(0xda, start_address + ESDCTL_DDR2_EMR2); /* EMRS2 */ - writeb(0xda, start_address + ESDCTL_DDR2_EMR3); /* EMRS3 */ - writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */ - writeb(0xda, start_address + ESDCTL_DDR2_RESET_DLL); /* Reset DLL */ - - /* Precharge ALL */ - writel(ESDCTL_0x92220000, - ctl_reg); - writel(0xda, start_address + ESDCTL_PRECHARGE); - - /* Set mode auto refresh : at least two refresh are required */ - writel(ESDCTL_0xA2220000, - ctl_reg); - writel(0xda, start_address); - writel(0xda, start_address); - - writel(ESDCTL_0xB2220000, - ctl_reg); - writeb(0xda, start_address + ESDCTL_DDR2_MR); - writeb(0xda, start_address + ESDCTL_DDR2_OCD_DEFAULT); - - /* OCD mode exit */ - writeb(0xda, start_address + ESDCTL_DDR2_EN_DLL); /* Enable DLL */ - - /* Set normal mode */ - writel(ESDCTL_0x82228080, - ctl_reg); - - dram_wait(0x20000); - - /* Do not set delay lines, only for MDDR */ -} - static void board_setup_sdram(void) { struct esdc_regs *esdc = (struct esdc_regs *)ESDCTL_BASE_ADDR; @@ -143,7 +57,9 @@ static void board_setup_sdram(void) writel(0x2000, &esdc->esdctl0); writel(0x2000, &esdc->esdctl1); - board_setup_sdram_bank(CSD0_BASE_ADDR); + + mx3_setup_sdram_bank(CSD0_BASE_ADDR, ESDCTL_DDR2_CONFIG, + 13, 10, 2, 0x8080); } static void setup_iomux_uart3(void) @@ -206,6 +122,8 @@ static void setup_iomux_fec(void) MX35_PAD_FEC_TDATA2__FEC_TDATA_2, MX35_PAD_FEC_RDATA3__FEC_RDATA_3, MX35_PAD_FEC_TDATA3__FEC_TDATA_3, + /* GPIO used to power off ethernet */ + MX35_PAD_STXFS4__GPIO2_31, }; /* setup pins for FEC */ @@ -267,6 +185,11 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + /* Enable power for ethernet */ + gpio_direction_output(63, 0); + + udelay(2000); + return 0; } @@ -276,3 +199,24 @@ u32 get_board_rev(void) return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8; } + +/* + * called prior to booting kernel or by 'fdt boardsetup' command + * + */ +int ft_board_setup(void *blob, bd_t *bd) +{ + struct node_info nodes[] = { + { "physmap-flash.0", MTD_DEV_TYPE_NOR, }, /* NOR flash */ + { "mxc_nand", MTD_DEV_TYPE_NAND, }, /* NAND flash */ + }; + + if (getenv("fdt_noauto")) { + puts(" Skiping ft_board_setup (fdt_noauto defined)\n"); + return 0; + } + + fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes)); + + return 0; +} |