summaryrefslogtreecommitdiff
path: root/board/amcc/bamboo/bamboo.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/amcc/bamboo/bamboo.c')
-rw-r--r--board/amcc/bamboo/bamboo.c1896
1 files changed, 0 insertions, 1896 deletions
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
deleted file mode 100644
index 9f642071cc..0000000000
--- a/board/amcc/bamboo/bamboo.c
+++ /dev/null
@@ -1,1896 +0,0 @@
-/*
- * (C) Copyright 2005-2007
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <asm/ppc4xx-gpio.h>
-#include <spd_sdram.h>
-#include <asm/ppc440.h>
-#include "bamboo.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void ext_bus_cntlr_init(void);
-void configure_ppc440ep_pins(void);
-int is_nand_selected(void);
-
-/*************************************************************************
- *
- * Bamboo has one bank onboard sdram (plus DIMM)
- *
- * Fixed memory is composed of :
- * MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266,
- * 13 row add bits, 10 column add bits (but 12 row used only).
- * ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266,
- * 12 row add bits, 10 column add bits.
- * Prepare a subset (only the used ones) of SPD data
- *
- * Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of
- * the corresponding bank is divided by 2 due to number of Row addresses
- * 12 in the ECC module
- *
- * Assumes: 64 MB, ECC, non-registered
- * PLB @ 133 MHz
- *
- ************************************************************************/
-const unsigned char cfg_simulate_spd_eeprom[128] = {
- 0x80, /* number of SPD bytes used: 128 */
- 0x08, /* total number bytes in SPD device = 256 */
- 0x07, /* DDR ram */
-#ifdef CONFIG_DDR_ECC
- 0x0C, /* num Row Addr: 12 */
-#else
- 0x0D, /* num Row Addr: 13 */
-#endif
- 0x09, /* numColAddr: 9 */
- 0x01, /* numBanks: 1 */
- 0x20, /* Module data width: 32 bits */
- 0x00, /* Module data width continued: +0 */
- 0x04, /* 2.5 Volt */
- 0x75, /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */
- 0x00, /* SDRAM Access from clock */
-#ifdef CONFIG_DDR_ECC
- 0x02, /* ECC ON : 02 OFF : 00 */
-#else
- 0x00, /* ECC ON : 02 OFF : 00 */
-#endif
- 0x82, /* refresh Rate Type: Normal (7.8us) + Self refresh */
- 0,
- 0,
- 0x01, /* wcsbc = 1 */
- 0,
- 0,
- 0x0C, /* casBit (2,2.5) */
- 0,
- 0,
- 0x00, /* not registered: 0 registered : 0x02*/
- 0,
- 0xA0, /* SDRAM Cycle Time (cas latency 2) = 10 ns */
- 0,
- 0x00, /* SDRAM Cycle Time (cas latency 1.5) = N.A */
- 0,
- 0x50, /* tRpNs = 20 ns */
- 0,
- 0x50, /* tRcdNs = 20 ns */
- 45, /* tRasNs */
-#ifdef CONFIG_DDR_ECC
- 0x08, /* bankSizeID: 32MB */
-#else
- 0x10, /* bankSizeID: 64MB */
-#endif
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0,
- 0
-};
-
-#if 0
-{ /* GPIO Alternate1 Alternate2 Alternate3 */
- {
- /* GPIO Core 0 */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_0 -> EBC_ADDR(7) DMA_REQ(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_1 -> EBC_ADDR(6) DMA_ACK(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_2 -> EBC_ADDR(5) DMA_EOT/TC(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_3 -> EBC_ADDR(4) DMA_REQ(3) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_4 -> EBC_ADDR(3) DMA_ACK(3) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_5 ................. */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_6 -> EBC_CS_N(1) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_7 -> EBC_CS_N(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_8 -> EBC_CS_N(3) */
- { GPIO0_BASE, GPIO_DIS, GPIO_ALT1 }, /* GPIO0_9 -> EBC_CS_N(4) */
- { GPIO0_BASE, GPIO_OUT, GPIO_ALT1 }, /* GPIO0_10 -> EBC_CS_N(5) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_11 -> EBC_BUS_ERR */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_12 -> ZII_p0Rxd(0) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_13 -> ZII_p0Rxd(1) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_14 -> ZII_p0Rxd(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_15 -> ZII_p0Rxd(3) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_16 -> ZII_p0Txd(0) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_17 -> ZII_p0Txd(1) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_18 -> ZII_p0Txd(2) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_19 -> ZII_p0Txd(3) */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_20 -> ZII_p0Rx_er */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_21 -> ZII_p0Rx_dv */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_22 -> ZII_p0RxCrs */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_23 -> ZII_p0Tx_er */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_24 -> ZII_p0Tx_en */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_25 -> ZII_p0Col */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_26 -> USB2D_RXVALID */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_27 -> EXT_EBC_REQ USB2D_RXERROR */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_28 -> USB2D_TXVALID */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_29 -> EBC_EXT_HDLA USB2D_PAD_SUSPNDM */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_30 -> EBC_EXT_ACK USB2D_XCVRSELECT */
- { GPIO0_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO0_31 -> EBC_EXR_BUSREQ USB2D_TERMSELECT */
- },
- {
- /* GPIO Core 1 */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_0 -> USB2D_OPMODE0 */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_1 -> USB2D_OPMODE1 */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_2 -> UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_3 -> UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_4 -> UART0_8PIN_CTS_N UART3_SIN */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_5 -> UART0_RTS_N */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_6 -> UART0_DTR_N UART1_SOUT */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_7 -> UART0_RI_N UART1_SIN */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_8 -> UIC_IRQ(0) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_9 -> UIC_IRQ(1) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_10 -> UIC_IRQ(2) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_11 -> UIC_IRQ(3) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_12 -> UIC_IRQ(4) DMA_ACK(1) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_13 -> UIC_IRQ(6) DMA_EOT/TC(1) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_14 -> UIC_IRQ(7) DMA_REQ(0) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_15 -> UIC_IRQ(8) DMA_ACK(0) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_16 -> UIC_IRQ(9) DMA_EOT/TC(0) */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_17 -> - */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_18 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_19 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_20 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_21 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_22 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_23 -> \ Can be unselected thru TraceSelect Bit */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_24 -> / in PowerPC440EP Chip */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_25 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_26 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_27 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_28 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_29 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_30 -> | */
- { GPIO1_BASE, GPIO_DIS, GPIO_SEL }, /* GPIO1_31 -> - */
- }
-};
-#endif
-
-/*----------------------------------------------------------------------------+
- | EBC Devices Characteristics
- | Peripheral Bank Access Parameters - EBC0_BnAP
- | Peripheral Bank Configuration Register - EBC0_BnCR
- +----------------------------------------------------------------------------*/
-/* Small Flash */
-#define EBC0_BNAP_SMALL_FLASH \
- EBC0_BNAP_BME_DISABLED | \
- EBC0_BNAP_TWT_ENCODE(6) | \
- EBC0_BNAP_CSN_ENCODE(0) | \
- EBC0_BNAP_OEN_ENCODE(1) | \
- EBC0_BNAP_WBN_ENCODE(1) | \
- EBC0_BNAP_WBF_ENCODE(3) | \
- EBC0_BNAP_TH_ENCODE(1) | \
- EBC0_BNAP_RE_ENABLED | \
- EBC0_BNAP_SOR_DELAYED | \
- EBC0_BNAP_BEM_WRITEONLY | \
- EBC0_BNAP_PEN_DISABLED
-
-#define EBC0_BNCR_SMALL_FLASH_CS0 \
- EBC0_BNCR_BAS_ENCODE(0xFFF00000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_8BIT
-
-#define EBC0_BNCR_SMALL_FLASH_CS4 \
- EBC0_BNCR_BAS_ENCODE(0x87F00000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_8BIT
-
-/* Large Flash or SRAM */
-#define EBC0_BNAP_LARGE_FLASH_OR_SRAM \
- EBC0_BNAP_BME_DISABLED | \
- EBC0_BNAP_TWT_ENCODE(8) | \
- EBC0_BNAP_CSN_ENCODE(0) | \
- EBC0_BNAP_OEN_ENCODE(1) | \
- EBC0_BNAP_WBN_ENCODE(1) | \
- EBC0_BNAP_WBF_ENCODE(1) | \
- EBC0_BNAP_TH_ENCODE(2) | \
- EBC0_BNAP_SOR_DELAYED | \
- EBC0_BNAP_BEM_RW | \
- EBC0_BNAP_PEN_DISABLED
-
-#define EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS0 \
- EBC0_BNCR_BAS_ENCODE(0xFF800000) | \
- EBC0_BNCR_BS_8MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_16BIT
-
-
-#define EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4 \
- EBC0_BNCR_BAS_ENCODE(0x87800000) | \
- EBC0_BNCR_BS_8MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_16BIT
-
-/* NVRAM - FPGA */
-#define EBC0_BNAP_NVRAM_FPGA \
- EBC0_BNAP_BME_DISABLED | \
- EBC0_BNAP_TWT_ENCODE(9) | \
- EBC0_BNAP_CSN_ENCODE(0) | \
- EBC0_BNAP_OEN_ENCODE(1) | \
- EBC0_BNAP_WBN_ENCODE(1) | \
- EBC0_BNAP_WBF_ENCODE(0) | \
- EBC0_BNAP_TH_ENCODE(2) | \
- EBC0_BNAP_RE_ENABLED | \
- EBC0_BNAP_SOR_DELAYED | \
- EBC0_BNAP_BEM_WRITEONLY | \
- EBC0_BNAP_PEN_DISABLED
-
-#define EBC0_BNCR_NVRAM_FPGA_CS5 \
- EBC0_BNCR_BAS_ENCODE(0x80000000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_8BIT
-
-/* Nand Flash */
-#define EBC0_BNAP_NAND_FLASH \
- EBC0_BNAP_BME_DISABLED | \
- EBC0_BNAP_TWT_ENCODE(3) | \
- EBC0_BNAP_CSN_ENCODE(0) | \
- EBC0_BNAP_OEN_ENCODE(0) | \
- EBC0_BNAP_WBN_ENCODE(0) | \
- EBC0_BNAP_WBF_ENCODE(0) | \
- EBC0_BNAP_TH_ENCODE(1) | \
- EBC0_BNAP_RE_ENABLED | \
- EBC0_BNAP_SOR_NOT_DELAYED | \
- EBC0_BNAP_BEM_RW | \
- EBC0_BNAP_PEN_DISABLED
-
-
-#define EBC0_BNCR_NAND_FLASH_CS0 0xB8400000
-
-/* NAND0 */
-#define EBC0_BNCR_NAND_FLASH_CS1 \
- EBC0_BNCR_BAS_ENCODE(0x90000000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_32BIT
-/* NAND1 - Bank2 */
-#define EBC0_BNCR_NAND_FLASH_CS2 \
- EBC0_BNCR_BAS_ENCODE(0x94000000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_32BIT
-
-/* NAND1 - Bank3 */
-#define EBC0_BNCR_NAND_FLASH_CS3 \
- EBC0_BNCR_BAS_ENCODE(0x94000000) | \
- EBC0_BNCR_BS_1MB | \
- EBC0_BNCR_BU_RW | \
- EBC0_BNCR_BW_32BIT
-
-int board_early_init_f(void)
-{
- ext_bus_cntlr_init();
-
- /*--------------------------------------------------------------------
- * Setup the interrupt controller polarities, triggers, etc.
- *-------------------------------------------------------------------*/
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
- mtdcr(UIC0ER, 0x00000000); /* disable all */
- mtdcr(UIC0CR, 0x00000009); /* ATI & UIC1 crit are critical */
- mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
- mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
- mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
-
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
- mtdcr(UIC1ER, 0x00000000); /* disable all */
- mtdcr(UIC1CR, 0x00000000); /* all non-critical */
- mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
- mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
- mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
-
- /*--------------------------------------------------------------------
- * Setup the GPIO pins
- *-------------------------------------------------------------------*/
- out32(GPIO0_OSRL, 0x00000400);
- out32(GPIO0_OSRH, 0x00000000);
- out32(GPIO0_TSRL, 0x00000400);
- out32(GPIO0_TSRH, 0x00000000);
- out32(GPIO0_ISR1L, 0x00000000);
- out32(GPIO0_ISR1H, 0x00000000);
- out32(GPIO0_ISR2L, 0x00000000);
- out32(GPIO0_ISR2H, 0x00000000);
- out32(GPIO0_ISR3L, 0x00000000);
- out32(GPIO0_ISR3H, 0x00000000);
-
- out32(GPIO1_OSRL, 0x0C380000);
- out32(GPIO1_OSRH, 0x00000000);
- out32(GPIO1_TSRL, 0x0C380000);
- out32(GPIO1_TSRH, 0x00000000);
- out32(GPIO1_ISR1L, 0x0FC30000);
- out32(GPIO1_ISR1H, 0x00000000);
- out32(GPIO1_ISR2L, 0x0C010000);
- out32(GPIO1_ISR2H, 0x00000000);
- out32(GPIO1_ISR3L, 0x01400000);
- out32(GPIO1_ISR3H, 0x00000000);
-
- configure_ppc440ep_pins();
-
- return 0;
-}
-
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- printf("Board: Bamboo - AMCC PPC440EP Evaluation Board");
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return (0);
-}
-
-
-int dram_init(void)
-{
- gd->ram_size = spd_sdram();
-
- return 0;
-}
-
-/*----------------------------------------------------------------------------+
- | is_powerpc440ep_pass1.
- +----------------------------------------------------------------------------*/
-int is_powerpc440ep_pass1(void)
-{
- unsigned long pvr;
-
- pvr = get_pvr();
-
- if (pvr == PVR_POWERPC_440EP_PASS1)
- return true;
- else if (pvr == PVR_POWERPC_440EP_PASS2)
- return false;
- else {
- printf("brdutil error 3\n");
- for (;;)
- ;
- }
-
- return false;
-}
-
-/*----------------------------------------------------------------------------+
- | is_nand_selected.
- +----------------------------------------------------------------------------*/
-int is_nand_selected(void)
-{
-#ifdef CONFIG_BAMBOO_NAND
- return true;
-#else
- return false;
-#endif
-}
-
-/*----------------------------------------------------------------------------+
- | config_on_ebc_cs4_is_small_flash => from EPLD
- +----------------------------------------------------------------------------*/
-unsigned char config_on_ebc_cs4_is_small_flash(void)
-{
- /* Not implemented yet => returns constant value */
- return true;
-}
-
-/*----------------------------------------------------------------------------+
- | Ext_bus_cntlr_init.
- | Initialize the external bus controller
- +----------------------------------------------------------------------------*/
-void ext_bus_cntlr_init(void)
-{
- unsigned long sdr0_pstrp0, sdr0_sdstp1;
- unsigned long bootstrap_settings, boot_selection, ebc_boot_size;
- int computed_boot_device = BOOT_DEVICE_UNKNOWN;
- unsigned long ebc0_cs0_bnap_value = 0, ebc0_cs0_bncr_value = 0;
- unsigned long ebc0_cs1_bnap_value = 0, ebc0_cs1_bncr_value = 0;
- unsigned long ebc0_cs2_bnap_value = 0, ebc0_cs2_bncr_value = 0;
- unsigned long ebc0_cs3_bnap_value = 0, ebc0_cs3_bncr_value = 0;
- unsigned long ebc0_cs4_bnap_value = 0, ebc0_cs4_bncr_value = 0;
-
-
- /*-------------------------------------------------------------------------+
- |
- | PART 1 : Initialize EBC Bank 5
- | ==============================
- | Bank5 is always associated to the NVRAM/EPLD.
- | It has to be initialized prior to other banks settings computation since
- | some board registers values may be needed
- |
- +-------------------------------------------------------------------------*/
- /* NVRAM - FPGA */
- mtebc(PB5AP, EBC0_BNAP_NVRAM_FPGA);
- mtebc(PB5CR, EBC0_BNCR_NVRAM_FPGA_CS5);
-
- /*-------------------------------------------------------------------------+
- |
- | PART 2 : Determine which boot device was selected
- | =========================================
- |
- | Read Pin Strap Register in PPC440EP
- | In case of boot from IIC, read Serial Device Strap Register1
- |
- | Result can either be :
- | - Boot from EBC 8bits => SMALL FLASH
- | - Boot from EBC 16bits => Large Flash or SRAM
- | - Boot from NAND Flash
- | - Boot from PCI
- |
- +-------------------------------------------------------------------------*/
- /* Read Pin Strap Register in PPC440EP */
- mfsdr(SDR0_PINSTP, sdr0_pstrp0);
- bootstrap_settings = sdr0_pstrp0 & SDR0_PSTRP0_BOOTSTRAP_MASK;
-
- /*-------------------------------------------------------------------------+
- | PPC440EP Pass1
- +-------------------------------------------------------------------------*/
- if (is_powerpc440ep_pass1() == true) {
- switch(bootstrap_settings) {
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0:
- /* Default Strap Settings 0 : CPU 400 - PLB 133 - Boot EBC 8 bit 33MHz */
- /* Boot from Small Flash */
- computed_boot_device = BOOT_FROM_SMALL_FLASH;
- break;
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1:
- /* Default Strap Settings 1 : CPU 533 - PLB 133 - Boot PCI 66MHz */
- /* Boot from PCI */
- computed_boot_device = BOOT_FROM_PCI;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2:
- /* Default Strap Settings 2 : CPU 500 - PLB 100 - Boot NDFC16 66MHz */
- /* Boot from Nand Flash */
- computed_boot_device = BOOT_FROM_NAND_FLASH0;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS3:
- /* Default Strap Settings 3 : CPU 333 - PLB 133 - Boot EBC 8 bit 66MHz */
- /* Boot from Small Flash */
- computed_boot_device = BOOT_FROM_SMALL_FLASH;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN:
- case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
- /* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
- /* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
- boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
- ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
-
- switch(boot_selection) {
- case SDR0_SDSTP1_BOOT_SEL_EBC:
- switch(ebc_boot_size) {
- case SDR0_SDSTP1_EBC_ROM_BS_16BIT:
- computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
- break;
- case SDR0_SDSTP1_EBC_ROM_BS_8BIT:
- computed_boot_device = BOOT_FROM_SMALL_FLASH;
- break;
- }
- break;
-
- case SDR0_SDSTP1_BOOT_SEL_PCI:
- computed_boot_device = BOOT_FROM_PCI;
- break;
-
- case SDR0_SDSTP1_BOOT_SEL_NDFC:
- computed_boot_device = BOOT_FROM_NAND_FLASH0;
- break;
- }
- break;
- }
- }
-
- /*-------------------------------------------------------------------------+
- | PPC440EP Pass2
- +-------------------------------------------------------------------------*/
- else {
- switch(bootstrap_settings) {
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS0:
- /* Default Strap Settings 0 : CPU 400 - PLB 133 - Boot EBC 8 bit 33MHz */
- /* Boot from Small Flash */
- computed_boot_device = BOOT_FROM_SMALL_FLASH;
- break;
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS1:
- /* Default Strap Settings 1 : CPU 333 - PLB 133 - Boot PCI 66MHz */
- /* Boot from PCI */
- computed_boot_device = BOOT_FROM_PCI;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS2:
- /* Default Strap Settings 2 : CPU 400 - PLB 100 - Boot NDFC16 33MHz */
- /* Boot from Nand Flash */
- computed_boot_device = BOOT_FROM_NAND_FLASH0;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS3:
- /* Default Strap Settings 3 : CPU 400 - PLB 100 - Boot EBC 16 bit 33MHz */
- /* Boot from Large Flash or SRAM */
- computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS4:
- /* Default Strap Settings 4 : CPU 333 - PLB 133 - Boot EBC 16 bit 66MHz */
- /* Boot from Large Flash or SRAM */
- computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_SETTINGS6:
- /* Default Strap Settings 6 : CPU 400 - PLB 100 - Boot PCI 33MHz */
- /* Boot from PCI */
- computed_boot_device = BOOT_FROM_PCI;
- break;
-
- case SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN:
- case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
- /* Default Strap Settings 5-7 */
- /* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
- /* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
- boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
- ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
-
- switch(boot_selection) {
- case SDR0_SDSTP1_BOOT_SEL_EBC:
- switch(ebc_boot_size) {
- case SDR0_SDSTP1_EBC_ROM_BS_16BIT:
- computed_boot_device = BOOT_FROM_LARGE_FLASH_OR_SRAM;
- break;
- case SDR0_SDSTP1_EBC_ROM_BS_8BIT:
- computed_boot_device = BOOT_FROM_SMALL_FLASH;
- break;
- }
- break;
-
- case SDR0_SDSTP1_BOOT_SEL_PCI:
- computed_boot_device = BOOT_FROM_PCI;
- break;
-
- case SDR0_SDSTP1_BOOT_SEL_NDFC:
- computed_boot_device = BOOT_FROM_NAND_FLASH0;
- break;
- }
- break;
- }
- }
-
- /*-------------------------------------------------------------------------+
- |
- | PART 3 : Compute EBC settings depending on selected boot device
- | ====== ======================================================
- |
- | Resulting EBC init will be among following configurations :
- |
- | - Boot from EBC 8bits => boot from SMALL FLASH selected
- | EBC-CS0 = Small Flash
- | EBC-CS1,2,3 = NAND Flash or
- | Exp.Slot depending on Soft Config
- | EBC-CS4 = SRAM/Large Flash or
- | Large Flash/SRAM depending on jumpers
- | EBC-CS5 = NVRAM / EPLD
- |
- | - Boot from EBC 16bits => boot from Large Flash or SRAM selected
- | EBC-CS0 = SRAM/Large Flash or
- | Large Flash/SRAM depending on jumpers
- | EBC-CS1,2,3 = NAND Flash or
- | Exp.Slot depending on Software Configuration
- | EBC-CS4 = Small Flash
- | EBC-CS5 = NVRAM / EPLD
- |
- | - Boot from NAND Flash
- | EBC-CS0 = NAND Flash0
- | EBC-CS1,2,3 = NAND Flash1
- | EBC-CS4 = SRAM/Large Flash or
- | Large Flash/SRAM depending on jumpers
- | EBC-CS5 = NVRAM / EPLD
- |
- | - Boot from PCI
- | EBC-CS0 = ...
- | EBC-CS1,2,3 = NAND Flash or
- | Exp.Slot depending on Software Configuration
- | EBC-CS4 = SRAM/Large Flash or
- | Large Flash/SRAM or
- | Small Flash depending on jumpers
- | EBC-CS5 = NVRAM / EPLD
- |
- +-------------------------------------------------------------------------*/
-
- switch(computed_boot_device) {
- /*------------------------------------------------------------------------- */
- case BOOT_FROM_SMALL_FLASH:
- /*------------------------------------------------------------------------- */
- ebc0_cs0_bnap_value = EBC0_BNAP_SMALL_FLASH;
- ebc0_cs0_bncr_value = EBC0_BNCR_SMALL_FLASH_CS0;
- if ((is_nand_selected()) == true) {
- /* NAND Flash */
- ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
- ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
- ebc0_cs2_bnap_value = EBC0_BNAP_NAND_FLASH;
- ebc0_cs2_bncr_value = EBC0_BNCR_NAND_FLASH_CS2;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- } else {
- /* Expansion Slot */
- ebc0_cs1_bnap_value = 0;
- ebc0_cs1_bncr_value = 0;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- }
- ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
- ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
-
- break;
-
- /*------------------------------------------------------------------------- */
- case BOOT_FROM_LARGE_FLASH_OR_SRAM:
- /*------------------------------------------------------------------------- */
- ebc0_cs0_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
- ebc0_cs0_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS0;
- if ((is_nand_selected()) == true) {
- /* NAND Flash */
- ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
- ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- } else {
- /* Expansion Slot */
- ebc0_cs1_bnap_value = 0;
- ebc0_cs1_bncr_value = 0;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- }
- ebc0_cs4_bnap_value = EBC0_BNAP_SMALL_FLASH;
- ebc0_cs4_bncr_value = EBC0_BNCR_SMALL_FLASH_CS4;
-
- break;
-
- /*------------------------------------------------------------------------- */
- case BOOT_FROM_NAND_FLASH0:
- /*------------------------------------------------------------------------- */
- ebc0_cs0_bnap_value = EBC0_BNAP_NAND_FLASH;
- ebc0_cs0_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
-
- ebc0_cs1_bnap_value = 0;
- ebc0_cs1_bncr_value = 0;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
-
- /* Large Flash or SRAM */
- ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
- ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
-
- break;
-
- /*------------------------------------------------------------------------- */
- case BOOT_FROM_PCI:
- /*------------------------------------------------------------------------- */
- ebc0_cs0_bnap_value = 0;
- ebc0_cs0_bncr_value = 0;
-
- if ((is_nand_selected()) == true) {
- /* NAND Flash */
- ebc0_cs1_bnap_value = EBC0_BNAP_NAND_FLASH;
- ebc0_cs1_bncr_value = EBC0_BNCR_NAND_FLASH_CS1;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- } else {
- /* Expansion Slot */
- ebc0_cs1_bnap_value = 0;
- ebc0_cs1_bncr_value = 0;
- ebc0_cs2_bnap_value = 0;
- ebc0_cs2_bncr_value = 0;
- ebc0_cs3_bnap_value = 0;
- ebc0_cs3_bncr_value = 0;
- }
-
- if ((config_on_ebc_cs4_is_small_flash()) == true) {
- /* Small Flash */
- ebc0_cs4_bnap_value = EBC0_BNAP_SMALL_FLASH;
- ebc0_cs4_bncr_value = EBC0_BNCR_SMALL_FLASH_CS4;
- } else {
- /* Large Flash or SRAM */
- ebc0_cs4_bnap_value = EBC0_BNAP_LARGE_FLASH_OR_SRAM;
- ebc0_cs4_bncr_value = EBC0_BNCR_LARGE_FLASH_OR_SRAM_CS4;
- }
-
- break;
-
- /*------------------------------------------------------------------------- */
- case BOOT_DEVICE_UNKNOWN:
- /*------------------------------------------------------------------------- */
- /* Error */
- break;
-
- }
-
-
- /*-------------------------------------------------------------------------+
- | Initialize EBC CONFIG
- +-------------------------------------------------------------------------*/
- mtdcr(EBC0_CFGADDR, EBC0_CFG);
- mtdcr(EBC0_CFGDATA, EBC0_CFG_EBTC_DRIVEN |
- EBC0_CFG_PTD_ENABLED |
- EBC0_CFG_RTC_2048PERCLK |
- EBC0_CFG_EMPL_LOW |
- EBC0_CFG_EMPH_LOW |
- EBC0_CFG_CSTC_DRIVEN |
- EBC0_CFG_BPF_ONEDW |
- EBC0_CFG_EMS_8BIT |
- EBC0_CFG_PME_DISABLED |
- EBC0_CFG_PMT_ENCODE(0) );
-
- /*-------------------------------------------------------------------------+
- | Initialize EBC Bank 0-4
- +-------------------------------------------------------------------------*/
- /* EBC Bank0 */
- mtebc(PB0AP, ebc0_cs0_bnap_value);
- mtebc(PB0CR, ebc0_cs0_bncr_value);
- /* EBC Bank1 */
- mtebc(PB1AP, ebc0_cs1_bnap_value);
- mtebc(PB1CR, ebc0_cs1_bncr_value);
- /* EBC Bank2 */
- mtebc(PB2AP, ebc0_cs2_bnap_value);
- mtebc(PB2CR, ebc0_cs2_bncr_value);
- /* EBC Bank3 */
- mtebc(PB3AP, ebc0_cs3_bnap_value);
- mtebc(PB3CR, ebc0_cs3_bncr_value);
- /* EBC Bank4 */
- mtebc(PB4AP, ebc0_cs4_bnap_value);
- mtebc(PB4CR, ebc0_cs4_bncr_value);
-
- return;
-}
-
-
-/*----------------------------------------------------------------------------+
- | get_uart_configuration.
- +----------------------------------------------------------------------------*/
-uart_config_nb_t get_uart_configuration(void)
-{
- return (L4);
-}
-
-/*----------------------------------------------------------------------------+
- | set_phy_configuration_through_fpga => to EPLD
- +----------------------------------------------------------------------------*/
-void set_phy_configuration_through_fpga(zmii_config_t config)
-{
-
- unsigned long fpga_selection_reg;
-
- fpga_selection_reg = in8(FPGA_SELECTION_1_REG) & ~FPGA_SEL_1_REG_PHY_MASK;
-
- switch(config)
- {
- case ZMII_CONFIGURATION_IS_MII:
- fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_MII;
- break;
- case ZMII_CONFIGURATION_IS_RMII:
- fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_RMII;
- break;
- case ZMII_CONFIGURATION_IS_SMII:
- fpga_selection_reg = fpga_selection_reg | FPGA_SEL_1_REG_SMII;
- break;
- case ZMII_CONFIGURATION_UNKNOWN:
- default:
- break;
- }
- out8(FPGA_SELECTION_1_REG,fpga_selection_reg);
-
-}
-
-/*----------------------------------------------------------------------------+
- | scp_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void scp_selection_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_IIC1_SCP_SEL_MASK;
- fpga_selection_2_reg |= FPGA_SEL2_REG_SEL_SCP;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | iic1_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void iic1_selection_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_IIC1_SCP_SEL_MASK;
- fpga_selection_2_reg |= FPGA_SEL2_REG_SEL_IIC1;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | dma_a_b_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void dma_a_b_selection_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) | FPGA_SEL2_REG_SEL_DMA_A_B;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | dma_a_b_unselect_in_fpga.
- +----------------------------------------------------------------------------*/
-void dma_a_b_unselect_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_SEL_DMA_A_B;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | dma_c_d_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void dma_c_d_selection_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) | FPGA_SEL2_REG_SEL_DMA_C_D;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | dma_c_d_unselect_in_fpga.
- +----------------------------------------------------------------------------*/
-void dma_c_d_unselect_in_fpga(void)
-{
- unsigned long fpga_selection_2_reg;
-
- fpga_selection_2_reg = in8(FPGA_SELECTION_2_REG) & ~FPGA_SEL2_REG_SEL_DMA_C_D;
- out8(FPGA_SELECTION_2_REG,fpga_selection_2_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | usb2_device_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void usb2_device_selection_in_fpga(void)
-{
- unsigned long fpga_selection_1_reg;
-
- fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) | FPGA_SEL_1_REG_USB2_DEV_SEL;
- out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | usb2_device_reset_through_fpga.
- +----------------------------------------------------------------------------*/
-void usb2_device_reset_through_fpga(void)
-{
- /* Perform soft Reset pulse */
- unsigned long fpga_reset_reg;
- int i;
-
- fpga_reset_reg = in8(FPGA_RESET_REG);
- out8(FPGA_RESET_REG,fpga_reset_reg | FPGA_RESET_REG_RESET_USB20_DEV);
- for (i=0; i<500; i++)
- udelay(1000);
- out8(FPGA_RESET_REG,fpga_reset_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | usb2_host_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void usb2_host_selection_in_fpga(void)
-{
- unsigned long fpga_selection_1_reg;
-
- fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) | FPGA_SEL_1_REG_USB2_HOST_SEL;
- out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | ndfc_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void ndfc_selection_in_fpga(void)
-{
- unsigned long fpga_selection_1_reg;
-
- fpga_selection_1_reg = in8(FPGA_SELECTION_1_REG) &~FPGA_SEL_1_REG_NF_SELEC_MASK;
- fpga_selection_1_reg |= FPGA_SEL_1_REG_NF0_SEL_BY_NFCS1;
- fpga_selection_1_reg |= FPGA_SEL_1_REG_NF1_SEL_BY_NFCS2;
- out8(FPGA_SELECTION_1_REG,fpga_selection_1_reg);
-}
-
-/*----------------------------------------------------------------------------+
- | uart_selection_in_fpga.
- +----------------------------------------------------------------------------*/
-void uart_selection_in_fpga(uart_config_nb_t uart_config)
-{
- /* FPGA register */
- unsigned char fpga_selection_3_reg;
-
- /* Read FPGA Reagister */
- fpga_selection_3_reg = in8(FPGA_SELECTION_3_REG);
-
- switch (uart_config)
- {
- case L1:
- /* ----------------------------------------------------------------------- */
- /* L1 configuration: UART0 = 8 pins */
- /* ----------------------------------------------------------------------- */
- /* Configure FPGA */
- fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
- fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG1;
- out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
-
- break;
-
- case L2:
- /* ----------------------------------------------------------------------- */
- /* L2 configuration: UART0 = 4 pins */
- /* UART1 = 4 pins */
- /* ----------------------------------------------------------------------- */
- /* Configure FPGA */
- fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
- fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG2;
- out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
-
- break;
-
- case L3:
- /* ----------------------------------------------------------------------- */
- /* L3 configuration: UART0 = 4 pins */
- /* UART1 = 2 pins */
- /* UART2 = 2 pins */
- /* ----------------------------------------------------------------------- */
- /* Configure FPGA */
- fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
- fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG3;
- out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
- break;
-
- case L4:
- /* Configure FPGA */
- fpga_selection_3_reg = fpga_selection_3_reg & ~FPGA_SEL3_REG_SEL_UART_CONFIG_MASK;
- fpga_selection_3_reg = fpga_selection_3_reg | FPGA_SEL3_REG_SEL_UART_CONFIG4;
- out8(FPGA_SELECTION_3_REG, fpga_selection_3_reg);
-
- break;
-
- default:
- /* Unsupported UART configuration number */
- for (;;)
- ;
- break;
-
- }
-}
-
-
-/*----------------------------------------------------------------------------+
- | init_default_gpio
- +----------------------------------------------------------------------------*/
-void init_default_gpio(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- int i;
-
- /* Init GPIO0 */
- for(i=0; i<GPIO_MAX; i++)
- {
- gpio_tab[GPIO0][i].add = GPIO0_BASE;
- gpio_tab[GPIO0][i].in_out = GPIO_DIS;
- gpio_tab[GPIO0][i].alt_nb = GPIO_SEL;
- }
-
- /* Init GPIO1 */
- for(i=0; i<GPIO_MAX; i++)
- {
- gpio_tab[GPIO1][i].add = GPIO1_BASE;
- gpio_tab[GPIO1][i].in_out = GPIO_DIS;
- gpio_tab[GPIO1][i].alt_nb = GPIO_SEL;
- }
-
- /* EBC_CS_N(5) - GPIO0_10 */
- gpio_tab[GPIO0][10].in_out = GPIO_OUT;
- gpio_tab[GPIO0][10].alt_nb = GPIO_ALT1;
-
- /* EBC_CS_N(4) - GPIO0_9 */
- gpio_tab[GPIO0][9].in_out = GPIO_OUT;
- gpio_tab[GPIO0][9].alt_nb = GPIO_ALT1;
-}
-
-/*----------------------------------------------------------------------------+
- | update_uart_ios
- +------------------------------------------------------------------------------
- |
- | Set UART Configuration in PowerPC440EP
- |
- | +---------------------------------------------------------------------+
- | | Configuartion | Connector | Nb of pins | Pins | Associated |
- | | Number | Port Name | available | naming | CORE |
- | +-----------------+---------------+------------+--------+-------------+
- | | L1 | Port_A | 8 | UART | UART core 0 |
- | +-----------------+---------------+------------+--------+-------------+
- | | L2 | Port_A | 4 | UART1 | UART core 0 |
- | | (L2D) | Port_B | 4 | UART2 | UART core 1 |
- | +-----------------+---------------+------------+--------+-------------+
- | | L3 | Port_A | 4 | UART1 | UART core 0 |
- | | (L3D) | Port_B | 2 | UART2 | UART core 1 |
- | | | Port_C | 2 | UART3 | UART core 2 |
- | +-----------------+---------------+------------+--------+-------------+
- | | | Port_A | 2 | UART1 | UART core 0 |
- | | L4 | Port_B | 2 | UART2 | UART core 1 |
- | | (L4D) | Port_C | 2 | UART3 | UART core 2 |
- | | | Port_D | 2 | UART4 | UART core 3 |
- | +-----------------+---------------+------------+--------+-------------+
- |
- | Involved GPIOs
- |
- | +------------------------------------------------------------------------------+
- | | GPIO | Aternate 1 | I/O | Alternate 2 | I/O | Alternate 3 | I/O |
- | +---------+------------------+-----+-----------------+-----+-------------+-----+
- | | GPIO1_2 | UART0_DCD_N | I | UART1_DSR_CTS_N | I | UART2_SOUT | O |
- | | GPIO1_3 | UART0_8PIN_DSR_N | I | UART1_RTS_DTR_N | O | UART2_SIN | I |
- | | GPIO1_4 | UART0_8PIN_CTS_N | I | NA | NA | UART3_SIN | I |
- | | GPIO1_5 | UART0_RTS_N | O | NA | NA | UART3_SOUT | O |
- | | GPIO1_6 | UART0_DTR_N | O | UART1_SOUT | O | NA | NA |
- | | GPIO1_7 | UART0_RI_N | I | UART1_SIN | I | NA | NA |
- | +------------------------------------------------------------------------------+
- |
- |
- +----------------------------------------------------------------------------*/
-
-void update_uart_ios(uart_config_nb_t uart_config, gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- switch (uart_config)
- {
- case L1:
- /* ----------------------------------------------------------------------- */
- /* L1 configuration: UART0 = 8 pins */
- /* ----------------------------------------------------------------------- */
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO1][2].in_out = GPIO_IN;
- gpio_tab[GPIO1][2].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][3].in_out = GPIO_IN;
- gpio_tab[GPIO1][3].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][4].in_out = GPIO_IN;
- gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][5].in_out = GPIO_OUT;
- gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][6].in_out = GPIO_OUT;
- gpio_tab[GPIO1][6].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][7].in_out = GPIO_IN;
- gpio_tab[GPIO1][7].alt_nb = GPIO_ALT1;
-
- break;
-
- case L2:
- /* ----------------------------------------------------------------------- */
- /* L2 configuration: UART0 = 4 pins */
- /* UART1 = 4 pins */
- /* ----------------------------------------------------------------------- */
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO1][2].in_out = GPIO_IN;
- gpio_tab[GPIO1][2].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][3].in_out = GPIO_OUT;
- gpio_tab[GPIO1][3].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][4].in_out = GPIO_IN;
- gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][5].in_out = GPIO_OUT;
- gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][6].in_out = GPIO_OUT;
- gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][7].in_out = GPIO_IN;
- gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
-
- break;
-
- case L3:
- /* ----------------------------------------------------------------------- */
- /* L3 configuration: UART0 = 4 pins */
- /* UART1 = 2 pins */
- /* UART2 = 2 pins */
- /* ----------------------------------------------------------------------- */
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO1][2].in_out = GPIO_OUT;
- gpio_tab[GPIO1][2].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][3].in_out = GPIO_IN;
- gpio_tab[GPIO1][3].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][4].in_out = GPIO_IN;
- gpio_tab[GPIO1][4].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][5].in_out = GPIO_OUT;
- gpio_tab[GPIO1][5].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][6].in_out = GPIO_OUT;
- gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][7].in_out = GPIO_IN;
- gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
-
- break;
-
- case L4:
- /* ----------------------------------------------------------------------- */
- /* L4 configuration: UART0 = 2 pins */
- /* UART1 = 2 pins */
- /* UART2 = 2 pins */
- /* UART3 = 2 pins */
- /* ----------------------------------------------------------------------- */
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO1][2].in_out = GPIO_OUT;
- gpio_tab[GPIO1][2].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][3].in_out = GPIO_IN;
- gpio_tab[GPIO1][3].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][4].in_out = GPIO_IN;
- gpio_tab[GPIO1][4].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][5].in_out = GPIO_OUT;
- gpio_tab[GPIO1][5].alt_nb = GPIO_ALT3;
-
- gpio_tab[GPIO1][6].in_out = GPIO_OUT;
- gpio_tab[GPIO1][6].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][7].in_out = GPIO_IN;
- gpio_tab[GPIO1][7].alt_nb = GPIO_ALT2;
-
- break;
-
- default:
- /* Unsupported UART configuration number */
- printf("ERROR - Unsupported UART configuration number.\n\n");
- for (;;)
- ;
- break;
-
- }
-
- /* Set input Selection Register on Alt_Receive for UART Input Core */
- out32(GPIO1_IS1L, (in32(GPIO1_IS1L) | 0x0FC30000));
- out32(GPIO1_IS2L, (in32(GPIO1_IS2L) | 0x0C030000));
- out32(GPIO1_IS3L, (in32(GPIO1_IS3L) | 0x03C00000));
-}
-
-/*----------------------------------------------------------------------------+
- | update_ndfc_ios(void).
- +----------------------------------------------------------------------------*/
-void update_ndfc_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO0][6].in_out = GPIO_OUT; /* EBC_CS_N(1) */
- gpio_tab[GPIO0][6].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][7].in_out = GPIO_OUT; /* EBC_CS_N(2) */
- gpio_tab[GPIO0][7].alt_nb = GPIO_ALT1;
-
-#if 0
- gpio_tab[GPIO0][7].in_out = GPIO_OUT; /* EBC_CS_N(3) */
- gpio_tab[GPIO0][7].alt_nb = GPIO_ALT1;
-#endif
-}
-
-/*----------------------------------------------------------------------------+
- | update_zii_ios(void).
- +----------------------------------------------------------------------------*/
-void update_zii_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- /* Update GPIO Configuration Table */
- gpio_tab[GPIO0][12].in_out = GPIO_IN; /* ZII_p0Rxd(0) */
- gpio_tab[GPIO0][12].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][13].in_out = GPIO_IN; /* ZII_p0Rxd(1) */
- gpio_tab[GPIO0][13].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][14].in_out = GPIO_IN; /* ZII_p0Rxd(2) */
- gpio_tab[GPIO0][14].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][15].in_out = GPIO_IN; /* ZII_p0Rxd(3) */
- gpio_tab[GPIO0][15].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][16].in_out = GPIO_OUT; /* ZII_p0Txd(0) */
- gpio_tab[GPIO0][16].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][17].in_out = GPIO_OUT; /* ZII_p0Txd(1) */
- gpio_tab[GPIO0][17].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][18].in_out = GPIO_OUT; /* ZII_p0Txd(2) */
- gpio_tab[GPIO0][18].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][19].in_out = GPIO_OUT; /* ZII_p0Txd(3) */
- gpio_tab[GPIO0][19].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][20].in_out = GPIO_IN; /* ZII_p0Rx_er */
- gpio_tab[GPIO0][20].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][21].in_out = GPIO_IN; /* ZII_p0Rx_dv */
- gpio_tab[GPIO0][21].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][22].in_out = GPIO_IN; /* ZII_p0Crs */
- gpio_tab[GPIO0][22].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][23].in_out = GPIO_OUT; /* ZII_p0Tx_er */
- gpio_tab[GPIO0][23].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][24].in_out = GPIO_OUT; /* ZII_p0Tx_en */
- gpio_tab[GPIO0][24].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][25].in_out = GPIO_IN; /* ZII_p0Col */
- gpio_tab[GPIO0][25].alt_nb = GPIO_ALT1;
-
-}
-
-/*----------------------------------------------------------------------------+
- | update_uic_0_3_irq_ios().
- +----------------------------------------------------------------------------*/
-void update_uic_0_3_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO1][8].in_out = GPIO_IN; /* UIC_IRQ(0) */
- gpio_tab[GPIO1][8].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][9].in_out = GPIO_IN; /* UIC_IRQ(1) */
- gpio_tab[GPIO1][9].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][10].in_out = GPIO_IN; /* UIC_IRQ(2) */
- gpio_tab[GPIO1][10].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][11].in_out = GPIO_IN; /* UIC_IRQ(3) */
- gpio_tab[GPIO1][11].alt_nb = GPIO_ALT1;
-}
-
-/*----------------------------------------------------------------------------+
- | update_uic_4_9_irq_ios().
- +----------------------------------------------------------------------------*/
-void update_uic_4_9_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO1][12].in_out = GPIO_IN; /* UIC_IRQ(4) */
- gpio_tab[GPIO1][12].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][13].in_out = GPIO_IN; /* UIC_IRQ(6) */
- gpio_tab[GPIO1][13].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][14].in_out = GPIO_IN; /* UIC_IRQ(7) */
- gpio_tab[GPIO1][14].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][15].in_out = GPIO_IN; /* UIC_IRQ(8) */
- gpio_tab[GPIO1][15].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][16].in_out = GPIO_IN; /* UIC_IRQ(9) */
- gpio_tab[GPIO1][16].alt_nb = GPIO_ALT1;
-}
-
-/*----------------------------------------------------------------------------+
- | update_dma_a_b_ios().
- +----------------------------------------------------------------------------*/
-void update_dma_a_b_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO1][12].in_out = GPIO_OUT; /* DMA_ACK(1) */
- gpio_tab[GPIO1][12].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][13].in_out = GPIO_BI; /* DMA_EOT/TC(1) */
- gpio_tab[GPIO1][13].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][14].in_out = GPIO_IN; /* DMA_REQ(0) */
- gpio_tab[GPIO1][14].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][15].in_out = GPIO_OUT; /* DMA_ACK(0) */
- gpio_tab[GPIO1][15].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][16].in_out = GPIO_BI; /* DMA_EOT/TC(0) */
- gpio_tab[GPIO1][16].alt_nb = GPIO_ALT2;
-}
-
-/*----------------------------------------------------------------------------+
- | update_dma_c_d_ios().
- +----------------------------------------------------------------------------*/
-void update_dma_c_d_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO0][0].in_out = GPIO_IN; /* DMA_REQ(2) */
- gpio_tab[GPIO0][0].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][1].in_out = GPIO_OUT; /* DMA_ACK(2) */
- gpio_tab[GPIO0][1].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][2].in_out = GPIO_BI; /* DMA_EOT/TC(2) */
- gpio_tab[GPIO0][2].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][3].in_out = GPIO_IN; /* DMA_REQ(3) */
- gpio_tab[GPIO0][3].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][4].in_out = GPIO_OUT; /* DMA_ACK(3) */
- gpio_tab[GPIO0][4].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][5].in_out = GPIO_BI; /* DMA_EOT/TC(3) */
- gpio_tab[GPIO0][5].alt_nb = GPIO_ALT2;
-
-}
-
-/*----------------------------------------------------------------------------+
- | update_ebc_master_ios().
- +----------------------------------------------------------------------------*/
-void update_ebc_master_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO0][27].in_out = GPIO_IN; /* EXT_EBC_REQ */
- gpio_tab[GPIO0][27].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */
- gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][30].in_out = GPIO_OUT; /* EBC_EXT_ACK */
- gpio_tab[GPIO0][30].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO0][31].in_out = GPIO_OUT; /* EBC_EXR_BUSREQ */
- gpio_tab[GPIO0][31].alt_nb = GPIO_ALT1;
-}
-
-/*----------------------------------------------------------------------------+
- | update_usb2_device_ios().
- +----------------------------------------------------------------------------*/
-void update_usb2_device_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO0][26].in_out = GPIO_IN; /* USB2D_RXVALID */
- gpio_tab[GPIO0][26].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][27].in_out = GPIO_IN; /* USB2D_RXERROR */
- gpio_tab[GPIO0][27].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][28].in_out = GPIO_OUT; /* USB2D_TXVALID */
- gpio_tab[GPIO0][28].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* USB2D_PAD_SUSPNDM */
- gpio_tab[GPIO0][29].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][30].in_out = GPIO_OUT; /* USB2D_XCVRSELECT */
- gpio_tab[GPIO0][30].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO0][31].in_out = GPIO_OUT; /* USB2D_TERMSELECT */
- gpio_tab[GPIO0][31].alt_nb = GPIO_ALT2;
-
- gpio_tab[GPIO1][0].in_out = GPIO_OUT; /* USB2D_OPMODE0 */
- gpio_tab[GPIO1][0].alt_nb = GPIO_ALT1;
-
- gpio_tab[GPIO1][1].in_out = GPIO_OUT; /* USB2D_OPMODE1 */
- gpio_tab[GPIO1][1].alt_nb = GPIO_ALT1;
-
-}
-
-/*----------------------------------------------------------------------------+
- | update_pci_patch_ios().
- +----------------------------------------------------------------------------*/
-void update_pci_patch_ios(gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */
- gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1;
-}
-
-/*----------------------------------------------------------------------------+
- | set_chip_gpio_configuration(unsigned char gpio_core,
- | gpio_param_s (*gpio_tab)[GPIO_MAX])
- | Put the core impacted by clock modification and sharing in reset.
- | Config the select registers to resolve the sharing depending of the config.
- | Configure the GPIO registers.
- |
- +----------------------------------------------------------------------------*/
-void set_chip_gpio_configuration(unsigned char gpio_core, gpio_param_s (*gpio_tab)[GPIO_MAX])
-{
- unsigned char i=0, j=0, reg_offset = 0;
- unsigned long gpio_reg, gpio_core_add;
-
- /* GPIO config of the GPIOs 0 to 31 */
- for (i=0; i<GPIO_MAX; i++, j++)
- {
- if (i == GPIO_MAX/2)
- {
- reg_offset = 4;
- j = i-16;
- }
-
- gpio_core_add = gpio_tab[gpio_core][i].add;
-
- if ( (gpio_tab[gpio_core][i].in_out == GPIO_IN) ||
- (gpio_tab[gpio_core][i].in_out == GPIO_BI ))
- {
- switch (gpio_tab[gpio_core][i].alt_nb)
- {
- case GPIO_SEL:
- break;
-
- case GPIO_ALT1:
- gpio_reg = in32(GPIO_IS1(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS1(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT2:
- gpio_reg = in32(GPIO_IS2(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS2(gpio_core_add+reg_offset), gpio_reg);
- break;
-
- case GPIO_ALT3:
- gpio_reg = in32(GPIO_IS3(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_IN_SEL >> (j*2));
- out32(GPIO_IS3(gpio_core_add+reg_offset), gpio_reg);
- break;
- }
- }
- if ( (gpio_tab[gpio_core][i].in_out == GPIO_OUT) ||
- (gpio_tab[gpio_core][i].in_out == GPIO_BI ))
- {
-
- switch (gpio_tab[gpio_core][i].alt_nb)
- {
- case GPIO_SEL:
- break;
- case GPIO_ALT1:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT1_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
- case GPIO_ALT2:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT2_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
- case GPIO_ALT3:
- gpio_reg = in32(GPIO_OS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
- out32(GPIO_OS(gpio_core_add+reg_offset), gpio_reg);
- gpio_reg = in32(GPIO_TS(gpio_core_add+reg_offset)) & ~(GPIO_MASK >> (j*2));
- gpio_reg = gpio_reg | (GPIO_ALT3_SEL >> (j*2));
- out32(GPIO_TS(gpio_core_add+reg_offset), gpio_reg);
- break;
- }
- }
- }
-}
-
-/*----------------------------------------------------------------------------+
- | force_bup_core_selection.
- +----------------------------------------------------------------------------*/
-void force_bup_core_selection(core_selection_t *core_select_P, config_validity_t *config_val_P)
-{
- /* Pointer invalid */
- if (core_select_P == NULL)
- {
- printf("Configuration invalid pointer 1\n");
- for (;;)
- ;
- }
-
- /* L4 Selection */
- *(core_select_P+UART_CORE0) = CORE_SELECTED;
- *(core_select_P+UART_CORE1) = CORE_SELECTED;
- *(core_select_P+UART_CORE2) = CORE_SELECTED;
- *(core_select_P+UART_CORE3) = CORE_SELECTED;
-
- /* RMII Selection */
- *(core_select_P+RMII_SEL) = CORE_SELECTED;
-
- /* External Interrupt 0-9 selection */
- *(core_select_P+UIC_0_3) = CORE_SELECTED;
- *(core_select_P+UIC_4_9) = CORE_SELECTED;
-
- *(core_select_P+SCP_CORE) = CORE_SELECTED;
- *(core_select_P+DMA_CHANNEL_CD) = CORE_SELECTED;
- *(core_select_P+PACKET_REJ_FUNC_AVAIL) = CORE_SELECTED;
- *(core_select_P+USB1_DEVICE) = CORE_SELECTED;
-
- if (is_nand_selected()) {
- *(core_select_P+NAND_FLASH) = CORE_SELECTED;
- }
-
- *config_val_P = CONFIG_IS_VALID;
-
-}
-
-/*----------------------------------------------------------------------------+
- | configure_ppc440ep_pins.
- +----------------------------------------------------------------------------*/
-void configure_ppc440ep_pins(void)
-{
- uart_config_nb_t uart_configuration;
- config_validity_t config_val = CONFIG_IS_INVALID;
-
- /* Create Core Selection Table */
- core_selection_t ppc440ep_core_selection[MAX_CORE_SELECT_NB] =
- {
- CORE_NOT_SELECTED, /* IIC_CORE, */
- CORE_NOT_SELECTED, /* SPC_CORE, */
- CORE_NOT_SELECTED, /* DMA_CHANNEL_AB, */
- CORE_NOT_SELECTED, /* UIC_4_9, */
- CORE_NOT_SELECTED, /* USB2_HOST, */
- CORE_NOT_SELECTED, /* DMA_CHANNEL_CD, */
- CORE_NOT_SELECTED, /* USB2_DEVICE, */
- CORE_NOT_SELECTED, /* PACKET_REJ_FUNC_AVAIL, */
- CORE_NOT_SELECTED, /* USB1_DEVICE, */
- CORE_NOT_SELECTED, /* EBC_MASTER, */
- CORE_NOT_SELECTED, /* NAND_FLASH, */
- CORE_NOT_SELECTED, /* UART_CORE0, */
- CORE_NOT_SELECTED, /* UART_CORE1, */
- CORE_NOT_SELECTED, /* UART_CORE2, */
- CORE_NOT_SELECTED, /* UART_CORE3, */
- CORE_NOT_SELECTED, /* MII_SEL, */
- CORE_NOT_SELECTED, /* RMII_SEL, */
- CORE_NOT_SELECTED, /* SMII_SEL, */
- CORE_NOT_SELECTED, /* PACKET_REJ_FUNC_EN */
- CORE_NOT_SELECTED, /* UIC_0_3 */
- CORE_NOT_SELECTED, /* USB1_HOST */
- CORE_NOT_SELECTED /* PCI_PATCH */
- };
-
- gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX];
-
- /* Table Default Initialisation + FPGA Access */
- init_default_gpio(gpio_tab);
- set_chip_gpio_configuration(GPIO0, gpio_tab);
- set_chip_gpio_configuration(GPIO1, gpio_tab);
-
- /* Update Table */
- force_bup_core_selection(ppc440ep_core_selection, &config_val);
-#if 0 /* test-only */
- /* If we are running PIBS 1, force known configuration */
- update_core_selection_table(ppc440ep_core_selection, &config_val);
-#endif
-
- /*----------------------------------------------------------------------------+
- | SDR + ios table update + fpga initialization
- +----------------------------------------------------------------------------*/
- unsigned long sdr0_pfc1 = 0;
- unsigned long sdr0_usb0 = 0;
- unsigned long sdr0_mfr = 0;
-
- /* PCI Always selected */
-
- /* I2C Selection */
- if (ppc440ep_core_selection[IIC_CORE] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_IIC1_SEL;
- iic1_selection_in_fpga();
- }
-
- /* SCP Selection */
- if (ppc440ep_core_selection[SCP_CORE] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SIS_MASK) | SDR0_PFC1_SIS_SCP_SEL;
- scp_selection_in_fpga();
- }
-
- /* UIC 0:3 Selection */
- if (ppc440ep_core_selection[UIC_0_3] == CORE_SELECTED)
- {
- update_uic_0_3_irq_ios(gpio_tab);
- dma_a_b_unselect_in_fpga();
- }
-
- /* UIC 4:9 Selection */
- if (ppc440ep_core_selection[UIC_4_9] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_UICIRQ5_SEL;
- update_uic_4_9_irq_ios(gpio_tab);
- }
-
- /* DMA AB Selection */
- if (ppc440ep_core_selection[DMA_CHANNEL_AB] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_DMAR_SEL;
- update_dma_a_b_ios(gpio_tab);
- dma_a_b_selection_in_fpga();
- }
-
- /* DMA CD Selection */
- if (ppc440ep_core_selection[DMA_CHANNEL_CD] == CORE_SELECTED)
- {
- update_dma_c_d_ios(gpio_tab);
- dma_c_d_selection_in_fpga();
- }
-
- /* EBC Master Selection */
- if (ppc440ep_core_selection[EBC_MASTER] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_ERE_MASK) | SDR0_PFC1_ERE_EXTR_SEL;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
- update_ebc_master_ios(gpio_tab);
- }
-
- /* PCI Patch Enable */
- if (ppc440ep_core_selection[PCI_PATCH] == CORE_SELECTED)
- {
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL;
- update_pci_patch_ios(gpio_tab);
- }
-
- /* USB2 Host Selection - Not Implemented in PowerPC 440EP Pass1 */
- if (ppc440ep_core_selection[USB2_HOST] == CORE_SELECTED)
- {
- /* Not Implemented in PowerPC 440EP Pass1-Pass2 */
- printf("Invalid configuration => USB2 Host selected\n");
- for (;;)
- ;
- /*usb2_host_selection_in_fpga(); */
- }
-
- /* USB2.0 Device Selection */
- if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)
- {
- update_usb2_device_ios(gpio_tab);
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
-
- mfsdr(SDR0_USB0, sdr0_usb0);
- sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
- sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB20D_DEVSEL;
- mtsdr(SDR0_USB0, sdr0_usb0);
-
- usb2_device_selection_in_fpga();
- }
-
- /* USB1.1 Device Selection */
- if (ppc440ep_core_selection[USB1_DEVICE] == CORE_SELECTED)
- {
- mfsdr(SDR0_USB0, sdr0_usb0);
- sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
- sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB11D_DEVSEL;
- mtsdr(SDR0_USB0, sdr0_usb0);
- }
-
- /* USB1.1 Host Selection */
- if (ppc440ep_core_selection[USB1_HOST] == CORE_SELECTED)
- {
- mfsdr(SDR0_USB0, sdr0_usb0);
- sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_LEEN_MASK;
- sdr0_usb0 = sdr0_usb0 | SDR0_USB0_LEEN_ENABLE;
- mtsdr(SDR0_USB0, sdr0_usb0);
- }
-
- /* NAND Flash Selection */
- if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED)
- {
- update_ndfc_ios(gpio_tab);
- mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
- SDR0_CUST0_NDFC_ENABLE |
- SDR0_CUST0_NDFC_BW_8_BIT |
- SDR0_CUST0_NDFC_ARE_MASK |
- SDR0_CUST0_CHIPSELGAT_EN1 |
- SDR0_CUST0_CHIPSELGAT_EN2);
- ndfc_selection_in_fpga();
- }
- else
- {
- /* Set Mux on EMAC */
- mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_EMAC_SEL);
- }
-
- /* MII Selection */
- if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
- {
- update_zii_ios(gpio_tab);
- mfsdr(SDR0_MFR, sdr0_mfr);
- sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
- mtsdr(SDR0_MFR, sdr0_mfr);
-
- set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_MII);
- }
-
- /* RMII Selection */
- if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
- {
- update_zii_ios(gpio_tab);
- mfsdr(SDR0_MFR, sdr0_mfr);
- sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
- mtsdr(SDR0_MFR, sdr0_mfr);
-
- set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_RMII);
- }
-
- /* SMII Selection */
- if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
- {
- update_zii_ios(gpio_tab);
- mfsdr(SDR0_MFR, sdr0_mfr);
- sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
- mtsdr(SDR0_MFR, sdr0_mfr);
-
- set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_SMII);
- }
-
- /* UART Selection */
- uart_configuration = get_uart_configuration();
- switch (uart_configuration)
- {
- case L1: /* L1 Selection */
- /* UART0 8 pins Only */
- /*sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U0ME_DSR_DTR; */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) |SDR0_PFC1_U0ME_CTS_RTS; /* Chip Pb */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_8PINS;
- break;
- case L2: /* L2 Selection */
- /* UART0 and UART1 4 pins */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
- break;
- case L3: /* L3 Selection */
- /* UART0 4 pins, UART1 and UART2 2 pins */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
- break;
- case L4: /* L4 Selection */
- /* UART0, UART1, UART2 and UART3 2 pins */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0ME_MASK) | SDR0_PFC1_U0ME_DSR_DTR;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U0IM_MASK) | SDR0_PFC1_U0IM_4PINS;
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR;
- break;
- }
- update_uart_ios(uart_configuration, gpio_tab);
-
- /* UART Selection in all cases */
- uart_selection_in_fpga(uart_configuration);
-
- /* Packet Reject Function Available */
- if (ppc440ep_core_selection[PACKET_REJ_FUNC_AVAIL] == CORE_SELECTED)
- {
- /* Set UPR Bit in SDR0_PFC1 Register */
- sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_ENABLE;
- }
-
- /* Packet Reject Function Enable */
- if (ppc440ep_core_selection[PACKET_REJ_FUNC_EN] == CORE_SELECTED)
- {
- mfsdr(SDR0_MFR, sdr0_mfr);
- sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_PKT_REJ_MASK) | SDR0_MFR_PKT_REJ_EN;
- mtsdr(SDR0_MFR, sdr0_mfr);
- }
-
- /* Perform effective access to hardware */
- mtsdr(SDR0_PFC1, sdr0_pfc1);
- set_chip_gpio_configuration(GPIO0, gpio_tab);
- set_chip_gpio_configuration(GPIO1, gpio_tab);
-
- /* USB2.0 Device Reset must be done after GPIO setting */
- if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED)
- usb2_device_reset_through_fpga();
-
-}