diff options
Diffstat (limited to 'board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c')
| -rw-r--r-- | board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 107 |
1 files changed, 9 insertions, 98 deletions
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c index 6871916865..d3bc5c69d4 100644 --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c @@ -7,6 +7,7 @@ */ #include <common.h> +#include <debug_uart.h> #include <asm/io.h> #include <asm/arch/clk.h> #include <asm/arch/at91sam9g45_matrix.h> @@ -17,11 +18,6 @@ #include <lcd.h> #include <linux/mtd/nand.h> #include <atmel_lcdc.h> -#include <atmel_mci.h> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) -#include <net.h> -#endif -#include <netdev.h> DECLARE_GLOBAL_DATA_PTR; @@ -149,39 +145,6 @@ static void at91sam9m10g45ek_usb_hw_init(void) } #endif -#ifdef CONFIG_MACB -static void at91sam9m10g45ek_macb_hw_init(void) -{ - struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA; - - at91_periph_clk_enable(ATMEL_ID_EMAC); - - /* - * Disable pull-up on: - * RXDV (PA15) => PHY normal mode (not Test mode) - * ERX0 (PA12) => PHY ADDR0 - * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0 - * - * PHY has internal pull-down - */ - writel(pin_to_mask(AT91_PIN_PA15) | - pin_to_mask(AT91_PIN_PA12) | - pin_to_mask(AT91_PIN_PA13), - &pioa->pudr); - - at91_phy_reset(); - - /* Re-enable pull-up */ - writel(pin_to_mask(AT91_PIN_PA15) | - pin_to_mask(AT91_PIN_PA12) | - pin_to_mask(AT91_PIN_PA13), - &pioa->puer); - - /* And the pins. */ - at91_macb_hw_init(); -} -#endif - #ifdef CONFIG_LCD vidinfo_t panel_info = { @@ -280,20 +243,22 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif -#ifdef CONFIG_GENERIC_ATMEL_MCI -int board_mmc_init(bd_t *bis) +#ifdef CONFIG_DEBUG_UART_BOARD_INIT +void board_debug_uart_init(void) { - at91_mci_hw_init(); - - return atmel_mci_init((void *)ATMEL_BASE_MCI0); + at91_seriald_hw_init(); } #endif +#ifdef CONFIG_BOARD_EARLY_INIT_F int board_early_init_f(void) { - at91_seriald_hw_init(); +#ifdef CONFIG_DEBUG_UART + debug_uart_init(); +#endif return 0; } +#endif int board_init(void) { @@ -313,15 +278,6 @@ int board_init(void) #ifdef CONFIG_CMD_USB at91sam9m10g45ek_usb_hw_init(); #endif -#ifdef CONFIG_HAS_DATAFLASH - at91_spi0_hw_init(1 << 0); -#endif -#ifdef CONFIG_ATMEL_SPI - at91_spi0_hw_init(1 << 4); -#endif -#ifdef CONFIG_MACB - at91sam9m10g45ek_macb_hw_init(); -#endif #ifdef CONFIG_LCD at91sam9m10g45ek_lcd_hw_init(); #endif @@ -340,48 +296,3 @@ void reset_phy(void) { } #endif - -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_MACB - rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00); -#endif - return rc; -} - -/* SPI chip select control */ -#ifdef CONFIG_ATMEL_SPI -#include <spi.h> - -int spi_cs_is_valid(unsigned int bus, unsigned int cs) -{ - return bus == 0 && cs < 2; -} - -void spi_cs_activate(struct spi_slave *slave) -{ - switch(slave->cs) { - case 1: - at91_set_gpio_output(AT91_PIN_PB18, 0); - break; - case 0: - default: - at91_set_gpio_output(AT91_PIN_PB3, 0); - break; - } -} - -void spi_cs_deactivate(struct spi_slave *slave) -{ - switch(slave->cs) { - case 1: - at91_set_gpio_output(AT91_PIN_PB18, 1); - break; - case 0: - default: - at91_set_gpio_output(AT91_PIN_PB3, 1); - break; - } -} -#endif /* CONFIG_ATMEL_SPI */ |