diff options
Diffstat (limited to 'board/delta/nand.c')
| -rw-r--r-- | board/delta/nand.c | 306 |
1 files changed, 306 insertions, 0 deletions
diff --git a/board/delta/nand.c b/board/delta/nand.c new file mode 100644 index 0000000000..9caddba064 --- /dev/null +++ b/board/delta/nand.c @@ -0,0 +1,306 @@ +/* + * (C) Copyright 2006 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) +#ifdef CONFIG_NEW_NAND_CODE + +#include <nand.h> +#include <asm/arch/pxa-regs.h> + +/* + * hardware specific access to control-lines + * function borrowed from Linux 2.6 (drivers/mtd/nand/ppchameleonevb.c) + */ +static void delta_hwcontrol(struct mtd_info *mtdinfo, int cmd) +{ +#if 0 + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + + switch(cmd) { + case NAND_CTL_SETCLE: + MACRO_NAND_CTL_SETCLE((unsigned long)base); + break; + case NAND_CTL_CLRCLE: + MACRO_NAND_CTL_CLRCLE((unsigned long)base); + break; + case NAND_CTL_SETALE: + MACRO_NAND_CTL_SETALE((unsigned long)base); + break; + case NAND_CTL_CLRALE: + MACRO_NAND_CTL_CLRALE((unsigned long)base); + break; + case NAND_CTL_SETNCE: + MACRO_NAND_ENABLE_CE((unsigned long)base); + break; + case NAND_CTL_CLRNCE: + MACRO_NAND_DISABLE_CE((unsigned long)base); + break; + } +#endif +} + + +/* read device ready pin */ +static int delta_device_ready(struct mtd_info *mtdinfo) +{ + if(NDSR & NDSR_RDY) + return 1; + else + return 0; +#if 0 + struct nand_chip *this = mtdinfo->priv; + ulong rb_gpio_pin; + + /* use the base addr to find out which chip are we dealing with */ + switch((ulong) this->IO_ADDR_W) { + case CFG_NAND0_BASE: + rb_gpio_pin = CFG_NAND0_RDY; + break; + case CFG_NAND1_BASE: + rb_gpio_pin = CFG_NAND1_RDY; + break; + default: /* this should never happen */ + return 0; + break; + } + + if (in32(GPIO0_IR) & rb_gpio_pin) + return 1; +#endif + return 0; +} + +static u_char delta_read_byte(struct mtd_info *mtd) +{ +/* struct nand_chip *this = mtd->priv; */ + unsigned long tmp; + + /* wait for read request */ + while(1) { + if(NDSR & NDSR_RDDREQ) { + NDSR |= NDSR_RDDREQ; + break; + } + } + + tmp = NDDB; + printk("delta_read_byte: 0x%x.\n", tmp); + return (u_char) tmp; +} + +/* this is really monahans, not board specific ... */ +static void delta_cmdfunc(struct mtd_info *mtd, unsigned command, + int column, int page_addr) +{ + /* register struct nand_chip *this = mtd->priv; */ + unsigned long ndcb0=0, ndcb1=0, ndcb2=0; + uchar command2; + + /* Clear NDSR */ + NDSR = 0xFFF; + + /* apparently NDCR[NDRUN] needs to be set before writing to NDCBx */ + NDCR |= NDCR_ND_RUN; + + /* wait for write command request + * hmm, might be nice if this could time-out. mk@tbd + */ + while(1) { + if(NDSR & NDSR_WRCMDREQ) { + NDSR |= NDSR_WRCMDREQ; /* Ack */ + break; + } + } + + /* if command is a double byte cmd, we set bit double cmd bit 19 */ + command2 = (command>>8) & 0xFF; + ndcb0 = command | ((command2 ? 1 : 0) << 19); + + switch (command) { + case NAND_CMD_READID: + printk("delta_cmdfunc: NAND_CMD_READID.\n"); + ndcb0 |= ((3 << 21) | (2 << 16)); + break; + case NAND_CMD_PAGEPROG: + case NAND_CMD_ERASE1: + case NAND_CMD_ERASE2: + case NAND_CMD_SEQIN: + case NAND_CMD_STATUS: + return; + case NAND_CMD_RESET: + return; + default: + printk("delta_cmdfunc: error, unkown command issued.\n"); + return; + } + + NDCB0 = ndcb0; + NDCB1 = ndcb1; + NDCB2 = ndcb2; +} + +/* + * Board-specific NAND initialization. The following members of the + * argument are board-specific (per include/linux/mtd/nand_new.h): + * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device + * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device + * - hwcontrol: hardwarespecific function for accesing control-lines + * - dev_ready: hardwarespecific function for accesing device ready/busy line + * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must + * only be provided if a hardware ECC is available + * - eccmode: mode of ecc, see defines + * - chip_delay: chip dependent delay for transfering data from array to + * read regs (tR) + * - options: various chip options. They can partly be set to inform + * nand_scan about special functionality. See the defines for further + * explanation + * Members with a "?" were not set in the merged testing-NAND branch, + * so they are not set here either. + */ +void board_nand_init(struct nand_chip *nand) +{ + unsigned long tCH, tCS, tWH, tWP, tRH, tRP, tRP_high, tR, tWHR, tAR; + + /* set up GPIO Control Registers */ + + /* turn on the NAND Controller Clock (104 MHz @ D0) */ + CKENA |= (CKENA_4_NAND | CKENA_9_SMC); + + /* NAND Timing Parameters (in ns) */ +#define NAND_TIMING_tCH 10 +#define NAND_TIMING_tCS 0 +#define NAND_TIMING_tWH 20 +#define NAND_TIMING_tWP 40 +#define NAND_TIMING_tRH 20 +#define NAND_TIMING_tRP 40 +#define NAND_TIMING_tR 11123 +#define NAND_TIMING_tWHR 110 +#define NAND_TIMING_tAR 10 + +/* Maximum values for NAND Interface Timing Registers in DFC clock + * periods */ +#define DFC_MAX_tCH 7 +#define DFC_MAX_tCS 7 +#define DFC_MAX_tWH 7 +#define DFC_MAX_tWP 7 +#define DFC_MAX_tRH 7 +#define DFC_MAX_tRP 15 +#define DFC_MAX_tR 65535 +#define DFC_MAX_tWHR 15 +#define DFC_MAX_tAR 15 + +#define DFC_CLOCK 104 /* DFC Clock is 104 MHz */ +#define DFC_CLK_PER_US DFC_CLOCK/1000 /* clock period in ns */ +#define MIN(x, y) ((x < y) ? x : y) + + + tCH = MIN(((unsigned long) (NAND_TIMING_tCH * DFC_CLK_PER_US) + 1), + DFC_MAX_tCH); + tCS = MIN(((unsigned long) (NAND_TIMING_tCS * DFC_CLK_PER_US) + 1), + DFC_MAX_tCS); + tWH = MIN(((unsigned long) (NAND_TIMING_tWH * DFC_CLK_PER_US) + 1), + DFC_MAX_tWH); + tWP = MIN(((unsigned long) (NAND_TIMING_tWP * DFC_CLK_PER_US) + 1), + DFC_MAX_tWP); + tRH = MIN(((unsigned long) (NAND_TIMING_tRH * DFC_CLK_PER_US) + 1), + DFC_MAX_tRH); + tRP = MIN(((unsigned long) (NAND_TIMING_tRP * DFC_CLK_PER_US) + 1), + DFC_MAX_tRP); + tR = MIN(((unsigned long) (NAND_TIMING_tR * DFC_CLK_PER_US) + 1), + DFC_MAX_tR); + tWHR = MIN(((unsigned long) (NAND_TIMING_tWHR * DFC_CLK_PER_US) + 1), + DFC_MAX_tWHR); + tAR = MIN(((unsigned long) (NAND_TIMING_tAR * DFC_CLK_PER_US) + 1), + DFC_MAX_tAR); + + + /* tRP value is split in the register */ + if(tRP & (1 << 4)) { + tRP_high = 1; + tRP &= ~(1 << 4); + } else { + tRP_high = 0; + } + + NDTR0CS0 = (tCH << 19) | + (tCS << 16) | + (tWH << 11) | + (tWP << 8) | + (tRP_high << 6) | + (tRH << 3) | + (tRP << 0); + + NDTR1CS0 = (tR << 16) | + (tWHR << 4) | + (tAR << 0); + + + + /* If it doesn't work (unlikely) think about: + * - ecc enable + * - chip select don't care + * - read id byte count + * + * Intentionally enabled by not setting bits: + * - dma (DMA_EN) + * - page size = 512 + * - cs don't care, see if we can enable later! + * - row address start position (after second cycle) + * - pages per block = 32 + */ + NDCR = (NDCR_ND_ARB_EN | /* enable bus arbiter */ + NDCR_SPARE_EN | /* use the spare area */ + NDCR_DWIDTH_C | /* 16bit DFC data bus width */ + NDCR_DWIDTH_M | /* 16 bit Flash device data bus width */ + (2 << 16) | /* read id count = 7 ???? mk@tbd */ + NDCE_RDYM | /* flash device ready ir masked */ + NDCE_CS0_PAGEDM | /* ND_nCSx page done ir masked */ + NDCE_CS1_PAGEDM | + NDCE_CS0_CMDDM | /* ND_CSx command done ir masked */ + NDCE_CS1_CMDDM | + NDCE_CS0_BBDM | /* ND_CSx bad block detect ir masked */ + NDCE_CS1_BBDM | + NDCE_DBERRM | /* double bit error ir masked */ + NDCE_SBERRM | /* single bit error ir masked */ + NDCE_WRDREQM | /* write data request ir masked */ + NDCE_RDDREQM | /* read data request ir masked */ + NDCE_WRCMDREQM); /* write command request ir masked */ + + + + nand->hwcontrol = delta_hwcontrol; + nand->dev_ready = delta_device_ready; + nand->eccmode = NAND_ECC_SOFT; + nand->chip_delay = NAND_DELAY_US; + nand->options = NAND_BUSWIDTH_16; + nand->read_byte = delta_read_byte; + nand->cmdfunc = delta_cmdfunc; + /* nand->options = NAND_SAMSUNG_LP_OPTIONS; */ +} + +#else +#error "U-Boot legacy NAND support not available for delta board." +#endif +#endif |