diff options
Diffstat (limited to 'board/freescale/b4860qds/ddr.c')
-rw-r--r-- | board/freescale/b4860qds/ddr.c | 267 |
1 files changed, 0 insertions, 267 deletions
diff --git a/board/freescale/b4860qds/ddr.c b/board/freescale/b4860qds/ddr.c deleted file mode 100644 index d3aa349ddf..0000000000 --- a/board/freescale/b4860qds/ddr.c +++ /dev/null @@ -1,267 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* - * Copyright 2011-2012 Freescale Semiconductor, Inc. - */ - -#include <common.h> -#include <i2c.h> -#include <hwconfig.h> -#include <fsl_ddr.h> -#include <init.h> -#include <log.h> -#include <asm/mmu.h> -#include <fsl_ddr_sdram.h> -#include <fsl_ddr_dimm_params.h> -#include <asm/fsl_law.h> - -DECLARE_GLOBAL_DATA_PTR; - -dimm_params_t ddr_raw_timing = { - .n_ranks = 2, - .rank_density = 2147483648u, - .capacity = 4294967296u, - .primary_sdram_width = 64, - .ec_sdram_width = 8, - .registered_dimm = 0, - .mirrored_dimm = 1, - .n_row_addr = 15, - .n_col_addr = 10, - .n_banks_per_sdram_device = 8, - .edc_config = 2, /* ECC */ - .burst_lengths_bitmask = 0x0c, - - .tckmin_x_ps = 1071, - .caslat_x = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */ - .taa_ps = 13910, - .twr_ps = 15000, - .trcd_ps = 13910, - .trrd_ps = 6000, - .trp_ps = 13910, - .tras_ps = 34000, - .trc_ps = 48910, - .trfc_ps = 260000, - .twtr_ps = 7500, - .trtp_ps = 7500, - .refresh_rate_ps = 7800000, - .tfaw_ps = 35000, -}; - -int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, - unsigned int controller_number, - unsigned int dimm_number) -{ - const char dimm_model[] = "RAW timing DDR"; - - if ((controller_number == 0) && (dimm_number == 0)) { - memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); - memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); - memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); - } - - return 0; -} - -struct board_specific_parameters { - u32 n_ranks; - u32 datarate_mhz_high; - u32 clk_adjust; - u32 wrlvl_start; - u32 wrlvl_ctl_2; - u32 wrlvl_ctl_3; - u32 cpo; - u32 write_data_delay; - u32 force_2t; -}; - -/* - * This table contains all valid speeds we want to override with board - * specific parameters. datarate_mhz_high values need to be in ascending order - * for each n_ranks group. - */ -static const struct board_specific_parameters udimm0[] = { - /* - * memory controller 0 - * num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T - * ranks| mhz|adjst| start | ctl2 | ctl3 | |delay | - */ - {2, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, - {2, 1666, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, - {2, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, - {1, 1350, 4, 7, 0x09080807, 0x07060607, 0xff, 2, 0}, - {1, 1700, 4, 7, 0x09080806, 0x06050607, 0xff, 2, 0}, - {1, 1900, 3, 7, 0x08070706, 0x06040507, 0xff, 2, 0}, - {} -}; - -static const struct board_specific_parameters *udimms[] = { - udimm0, -}; - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; - ulong ddr_freq; - - if (ctrl_num > 2) { - printf("Not supported controller number %d\n", ctrl_num); - return; - } - if (!pdimm->n_ranks) - return; - - pbsp = udimms[0]; - - - /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr - * freqency and n_banks specified in board_specific_parameters table. - */ - ddr_freq = get_ddr_freq(0) / 1000000; - while (pbsp->datarate_mhz_high) { - if (pbsp->n_ranks == pdimm->n_ranks) { - if (ddr_freq <= pbsp->datarate_mhz_high) { - popts->cpo_override = pbsp->cpo; - popts->write_data_delay = - pbsp->write_data_delay; - popts->clk_adjust = pbsp->clk_adjust; - popts->wrlvl_start = pbsp->wrlvl_start; - popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; - popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; - popts->twot_en = pbsp->force_2t; - goto found; - } - pbsp_highest = pbsp; - } - pbsp++; - } - - if (pbsp_highest) { - printf("Error: board specific timing not found " - "for data rate %lu MT/s\n" - "Trying to use the highest speed (%u) parameters\n", - ddr_freq, pbsp_highest->datarate_mhz_high); - popts->cpo_override = pbsp_highest->cpo; - popts->write_data_delay = pbsp_highest->write_data_delay; - popts->clk_adjust = pbsp_highest->clk_adjust; - popts->wrlvl_start = pbsp_highest->wrlvl_start; - popts->twot_en = pbsp_highest->force_2t; - } else { - panic("DIMM is not supported by this board"); - } -found: - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; - /* - * Write leveling override - */ - popts->wrlvl_override = 1; - popts->wrlvl_sample = 0xf; - - /* - * Rtt and Rtt_WR override - */ - popts->rtt_override = 0; - - /* Enable ZQ calibration */ - popts->zq_en = 1; - - /* DHC_EN =1, ODT = 75 Ohm */ - popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); - popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); - - /* optimize cpo for erratum A-009942 */ - popts->cpo_sample = 0x3e; -} - -int dram_init(void) -{ - phys_size_t dram_size; - -#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL) - puts("Initializing....using SPD\n"); - dram_size = fsl_ddr_sdram(); -#else - dram_size = fsl_ddr_sdram_size(); -#endif - dram_size = setup_ddr_tlbs(dram_size / 0x100000); - dram_size *= 0x100000; - - gd->ram_size = dram_size; - - return 0; -} - -unsigned long long step_assign_addresses(fsl_ddr_info_t *pinfo, - unsigned int dbw_cap_adj[]) -{ - int i, j; - unsigned long long total_mem, current_mem_base, total_ctlr_mem; - unsigned long long rank_density, ctlr_density = 0; - - current_mem_base = 0ull; - total_mem = 0; - /* - * This board has soldered DDR chips. DDRC1 has two rank. - * DDRC2 has only one rank. - * Assigning DDRC2 to lower address and DDRC1 to higher address. - */ - if (pinfo->memctl_opts[0].memctl_interleaving) { - rank_density = pinfo->dimm_params[0][0].rank_density >> - dbw_cap_adj[0]; - ctlr_density = rank_density; - - debug("rank density is 0x%llx, ctlr density is 0x%llx\n", - rank_density, ctlr_density); - for (i = CONFIG_SYS_NUM_DDR_CTLRS - 1; i >= 0; i--) { - switch (pinfo->memctl_opts[i].memctl_interleaving_mode) { - case FSL_DDR_CACHE_LINE_INTERLEAVING: - case FSL_DDR_PAGE_INTERLEAVING: - case FSL_DDR_BANK_INTERLEAVING: - case FSL_DDR_SUPERBANK_INTERLEAVING: - total_ctlr_mem = 2 * ctlr_density; - break; - default: - panic("Unknown interleaving mode"); - } - pinfo->common_timing_params[i].base_address = - current_mem_base; - pinfo->common_timing_params[i].total_mem = - total_ctlr_mem; - total_mem = current_mem_base + total_ctlr_mem; - debug("ctrl %d base 0x%llx\n", i, current_mem_base); - debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); - } - } else { - /* - * Simple linear assignment if memory - * controllers are not interleaved. - */ - for (i = CONFIG_SYS_NUM_DDR_CTLRS - 1; i >= 0; i--) { - total_ctlr_mem = 0; - pinfo->common_timing_params[i].base_address = - current_mem_base; - for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { - /* Compute DIMM base addresses. */ - unsigned long long cap = - pinfo->dimm_params[i][j].capacity; - pinfo->dimm_params[i][j].base_address = - current_mem_base; - debug("ctrl %d dimm %d base 0x%llx\n", - i, j, current_mem_base); - current_mem_base += cap; - total_ctlr_mem += cap; - } - debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); - pinfo->common_timing_params[i].total_mem = - total_ctlr_mem; - total_mem += total_ctlr_mem; - } - } - debug("Total mem by %s is 0x%llx\n", __func__, total_mem); - - return total_mem; -} |