diff options
Diffstat (limited to 'board/freescale/t102xqds')
| -rw-r--r-- | board/freescale/t102xqds/README | 30 | ||||
| -rw-r--r-- | board/freescale/t102xqds/eth_t102xqds.c | 2 |
2 files changed, 16 insertions, 16 deletions
diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README index bb0f2805dc..c00e3bafbe 100644 --- a/board/freescale/t102xqds/README +++ b/board/freescale/t102xqds/README @@ -172,16 +172,16 @@ Start Address End Address Description Size 128MB NOR Flash memory Map -------------------------- Start Address End Address Definition Max size -0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB -0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB +0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB +0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB 0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB 0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB 0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB 0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB 0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB 0xEC000000 0xEC01FFFF RCW (alt bank) 128KB -0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB -0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB +0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB +0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB 0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB 0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB 0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB @@ -221,11 +221,11 @@ Software configurations and board settings Switching between default bank0 and alternate bank4 on NOR flash To change boot source to vbank4: - via software: run command 'qixis_reset altbank' in u-boot. + via software: run command 'qixis_reset altbank' in U-Boot. via DIP-switch: set SW6[1:4] = '0100' To change boot source to vbank0: - via software: run command 'qixis_reset' in u-boot. + via software: run command 'qixis_reset' in U-Boot. via DIP-Switch: set SW6[1:4] = '0000' 2. NAND Boot: @@ -273,8 +273,8 @@ e) For SDXC: set adaptor=sdxc in hwconfig ------------------------------- PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM. SPL further initializes DDR using SPD and environment variables -and copy u-boot(768 KB) from NAND/SPI/SD device to DDR. -Finally SPL transers control to u-boot for futher booting. +and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR. +Finally SPL transers control to U-Boot for futher booting. SPL has following features: - Executes within 256K @@ -294,14 +294,14 @@ Run time view of SPL framework ------------------------------------------------- |STACK | 0xFFFD8000 (22KB) | ------------------------------------------------- -|U-boot SPL | 0xFFFD8000 (160KB) | +|U-Boot SPL | 0xFFFD8000 (160KB) | ------------------------------------------------- NAND Flash memory Map on T1024QDS ------------------------------------------------------------- Start End Definition Size -0x000000 0x0FFFFF u-boot 1MB -0x100000 0x15FFFF u-boot env 8KB +0x000000 0x0FFFFF U-Boot 1MB +0x100000 0x15FFFF U-Boot env 8KB 0x160000 0x17FFFF FMAN Ucode 128KB 0x180000 0x19FFFF QE Firmware 128KB @@ -309,8 +309,8 @@ Start End Definition Size SD Card memory Map on T1024QDS ---------------------------------------------------- Block #blocks Definition Size -0x008 2048 u-boot img 1MB -0x800 0016 u-boot env 8KB +0x008 2048 U-Boot img 1MB +0x800 0016 U-Boot env 8KB 0x820 0256 FMAN Ucode 128KB 0x920 0256 QE Firmware 128KB @@ -318,8 +318,8 @@ Block #blocks Definition Size SPI Flash memory Map on T1024QDS ---------------------------------------------------- Start End Definition Size -0x000000 0x0FFFFF u-boot img 1MB -0x100000 0x101FFF u-boot env 8KB +0x000000 0x0FFFFF U-Boot img 1MB +0x100000 0x101FFF U-Boot env 8KB 0x110000 0x12FFFF FMAN Ucode 128KB 0x130000 0x14FFFF QE Firmware 128KB diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c index ca54e2a4f0..19543c0738 100644 --- a/board/freescale/t102xqds/eth_t102xqds.c +++ b/board/freescale/t102xqds/eth_t102xqds.c @@ -310,7 +310,7 @@ int board_eth_init(bd_t *bis) case 0x95: case 0x99: /* - * XFI does not need a PHY to work, but to avoid U-boot use + * XFI does not need a PHY to work, but to avoid U-Boot use * default PHY address which is zero to a MAC when it found * a MAC has no PHY address, we give a PHY address to XFI * MAC, and should not use a real XAUI PHY address, since |