diff options
Diffstat (limited to 'board/gateworks/gw_ventana/gw_ventana_spl.c')
| -rw-r--r-- | board/gateworks/gw_ventana/gw_ventana_spl.c | 419 |
1 files changed, 419 insertions, 0 deletions
diff --git a/board/gateworks/gw_ventana/gw_ventana_spl.c b/board/gateworks/gw_ventana/gw_ventana_spl.c new file mode 100644 index 0000000000..e943879303 --- /dev/null +++ b/board/gateworks/gw_ventana/gw_ventana_spl.c @@ -0,0 +1,419 @@ +/* + * Copyright (C) 2014 Gateworks Corporation + * Author: Tim Harvey <tharvey@gateworks.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/iomux.h> +#include <asm/arch/mx6-ddr.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/imx-common/boot_mode.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/mxc_i2c.h> +#include <spl.h> + +#include "ventana_eeprom.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */ +#define I2C_GSC 0 +#define GSC_EEPROM_ADDR 0x51 +#define GSC_EEPROM_DDR_SIZE 0x2B /* enum (512,1024,2048) MB */ +#define GSC_EEPROM_DDR_WIDTH 0x2D /* enum (32,64) bit */ +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ + PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE | PAD_CTL_SRE_FAST) +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +#define CONFIG_SYS_I2C_SPEED 100000 + +/* I2C1: GSC */ +static struct i2c_pads_info mx6q_i2c_pad_info0 = { + .scl = { + .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC, + .gpio_mode = MX6Q_PAD_EIM_D21__GPIO3_IO21 | PC, + .gp = IMX_GPIO_NR(3, 21) + }, + .sda = { + .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC, + .gpio_mode = MX6Q_PAD_EIM_D28__GPIO3_IO28 | PC, + .gp = IMX_GPIO_NR(3, 28) + } +}; +static struct i2c_pads_info mx6dl_i2c_pad_info0 = { + .scl = { + .i2c_mode = MX6DL_PAD_EIM_D21__I2C1_SCL | PC, + .gpio_mode = MX6DL_PAD_EIM_D21__GPIO3_IO21 | PC, + .gp = IMX_GPIO_NR(3, 21) + }, + .sda = { + .i2c_mode = MX6DL_PAD_EIM_D28__I2C1_SDA | PC, + .gpio_mode = MX6DL_PAD_EIM_D28__GPIO3_IO28 | PC, + .gp = IMX_GPIO_NR(3, 28) + } +}; + +static void i2c_setup_iomux(void) +{ + if (is_cpu_type(MXC_CPU_MX6Q)) + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info0); + else + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info0); +} + +/* configure MX6Q/DUAL mmdc DDR io registers */ +struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = { + /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ + .dram_sdclk_0 = 0x00020030, + .dram_sdclk_1 = 0x00020030, + .dram_cas = 0x00020030, + .dram_ras = 0x00020030, + .dram_reset = 0x00020030, + /* SDCKE[0:1]: 100k pull-up */ + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + /* SDBA2: pull-up disabled */ + .dram_sdba2 = 0x00000000, + /* SDODT[0:1]: 100k pull-up, 40 ohm */ + .dram_sdodt0 = 0x00003030, + .dram_sdodt1 = 0x00003030, + /* SDQS[0:7]: Differential input, 40 ohm */ + .dram_sdqs0 = 0x00000030, + .dram_sdqs1 = 0x00000030, + .dram_sdqs2 = 0x00000030, + .dram_sdqs3 = 0x00000030, + .dram_sdqs4 = 0x00000030, + .dram_sdqs5 = 0x00000030, + .dram_sdqs6 = 0x00000030, + .dram_sdqs7 = 0x00000030, + + /* DQM[0:7]: Differential input, 40 ohm */ + .dram_dqm0 = 0x00020030, + .dram_dqm1 = 0x00020030, + .dram_dqm2 = 0x00020030, + .dram_dqm3 = 0x00020030, + .dram_dqm4 = 0x00020030, + .dram_dqm5 = 0x00020030, + .dram_dqm6 = 0x00020030, + .dram_dqm7 = 0x00020030, +}; + +/* configure MX6Q/DUAL mmdc GRP io registers */ +struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = { + /* DDR3 */ + .grp_ddr_type = 0x000c0000, + .grp_ddrmode_ctl = 0x00020000, + /* disable DDR pullups */ + .grp_ddrpke = 0x00000000, + /* ADDR[00:16], SDBA[0:1]: 40 ohm */ + .grp_addds = 0x00000030, + /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ + .grp_ctlds = 0x00000030, + /* DATA[00:63]: Differential input, 40 ohm */ + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000030, + .grp_b1ds = 0x00000030, + .grp_b2ds = 0x00000030, + .grp_b3ds = 0x00000030, + .grp_b4ds = 0x00000030, + .grp_b5ds = 0x00000030, + .grp_b6ds = 0x00000030, + .grp_b7ds = 0x00000030, +}; + +/* configure MX6SOLO/DUALLITE mmdc DDR io registers */ +struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = { + /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */ + .dram_sdclk_0 = 0x00020030, + .dram_sdclk_1 = 0x00020030, + .dram_cas = 0x00020030, + .dram_ras = 0x00020030, + .dram_reset = 0x00020030, + /* SDCKE[0:1]: 100k pull-up */ + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + /* SDBA2: pull-up disabled */ + .dram_sdba2 = 0x00000000, + /* SDODT[0:1]: 100k pull-up, 40 ohm */ + .dram_sdodt0 = 0x00003030, + .dram_sdodt1 = 0x00003030, + /* SDQS[0:7]: Differential input, 40 ohm */ + .dram_sdqs0 = 0x00000030, + .dram_sdqs1 = 0x00000030, + .dram_sdqs2 = 0x00000030, + .dram_sdqs3 = 0x00000030, + .dram_sdqs4 = 0x00000030, + .dram_sdqs5 = 0x00000030, + .dram_sdqs6 = 0x00000030, + .dram_sdqs7 = 0x00000030, + + /* DQM[0:7]: Differential input, 40 ohm */ + .dram_dqm0 = 0x00020030, + .dram_dqm1 = 0x00020030, + .dram_dqm2 = 0x00020030, + .dram_dqm3 = 0x00020030, + .dram_dqm4 = 0x00020030, + .dram_dqm5 = 0x00020030, + .dram_dqm6 = 0x00020030, + .dram_dqm7 = 0x00020030, +}; + +/* configure MX6SOLO/DUALLITE mmdc GRP io registers */ +struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { + /* DDR3 */ + .grp_ddr_type = 0x000c0000, + /* SDQS[0:7]: Differential input, 40 ohm */ + .grp_ddrmode_ctl = 0x00020000, + /* disable DDR pullups */ + .grp_ddrpke = 0x00000000, + /* ADDR[00:16], SDBA[0:1]: 40 ohm */ + .grp_addds = 0x00000030, + /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */ + .grp_ctlds = 0x00000030, + /* DATA[00:63]: Differential input, 40 ohm */ + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000030, + .grp_b1ds = 0x00000030, + .grp_b2ds = 0x00000030, + .grp_b3ds = 0x00000030, + .grp_b4ds = 0x00000030, + .grp_b5ds = 0x00000030, + .grp_b6ds = 0x00000030, + .grp_b7ds = 0x00000030, +}; + +/* MT41K128M16JT-125 */ +static struct mx6_ddr3_cfg mt41k128m16jt_125 = { + .mem_speed = 1600, + .density = 2, + .width = 16, + .banks = 8, + .rowaddr = 14, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, +}; + +/* GW54xx specific calibration */ +static struct mx6_mmdc_calibration gw54xxq_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x00190018, + .p0_mpwldectrl1 = 0x0021001D, + .p1_mpwldectrl0 = 0x00160027, + .p1_mpwldectrl1 = 0x0012001E, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x43370346, + .p0_mpdgctrl1 = 0x032A0321, + .p1_mpdgctrl0 = 0x433A034D, + .p1_mpdgctrl1 = 0x032F0235, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x3C313539, + .p1_mprddlctl = 0x37333140, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x37393C38, + .p1_mpwrdlctl = 0x42334538, +}; + +/* GW53xx specific calibration */ +static struct mx6_mmdc_calibration gw53xxq_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x00160013, + .p0_mpwldectrl1 = 0x00090024, + .p1_mpwldectrl0 = 0x001F0018, + .p1_mpwldectrl1 = 0x000C001C, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x433A034C, + .p0_mpdgctrl1 = 0x0336032F, + .p1_mpdgctrl0 = 0x4343034A, + .p1_mpdgctrl1 = 0x03370222, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x3F343638, + .p1_mprddlctl = 0x38373442, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x343A3E39, + .p1_mpwrdlctl = 0x44344239, +}; +static struct mx6_mmdc_calibration gw53xxdl_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x003C003C, + .p0_mpwldectrl1 = 0x00330038, + .p1_mpwldectrl0 = 0x001F002A, + .p1_mpwldectrl1 = 0x0022003F, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x42410244, + .p0_mpdgctrl1 = 0x022D022D, + .p1_mpdgctrl0 = 0x4234023A, + .p1_mpdgctrl1 = 0x021C0228, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x484A4C4B, + .p1_mprddlctl = 0x4B4D4E4B, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x33342B32, + .p1_mpwrdlctl = 0x3933332B, +}; + +/* GW52xx specific calibration */ +static struct mx6_mmdc_calibration gw52xxdl_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x0040003F, + .p0_mpwldectrl1 = 0x00370037, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x42420244, + .p0_mpdgctrl1 = 0x022F022F, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x49464B4A, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x32362C32, +}; + +/* GW51xx specific calibration */ +static struct mx6_mmdc_calibration gw51xxq_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x00150016, + .p0_mpwldectrl1 = 0x001F0017, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x433D034D, + .p0_mpdgctrl1 = 0x033D032F, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x3F313639, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x33393F36, +}; + +static struct mx6_mmdc_calibration gw51xxdl_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x003D003F, + .p0_mpwldectrl1 = 0x002F0038, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x423A023A, + .p0_mpdgctrl1 = 0x022A0228, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x48494C4C, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x34352D31, +}; + +static void spl_dram_init(int width, int size, int board_model) +{ + struct mx6_ddr3_cfg *mem = &mt41k128m16jt_125; + struct mx6_mmdc_calibration *calib; + struct mx6_ddr_sysinfo sysinfo = { + /* width of data bus:0=16,1=32,2=64 */ + .dsize = width/32, + /* config for full 4GB range so that get_mem_size() works */ + .cs_density = 32, /* 32Gb per CS */ + /* single chip select */ + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */ +#ifdef RTT_NOM_120OHM + .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */ +#else + .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */ +#endif + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + }; + + /* + * MMDC Calibration requires the following data: + * mx6_mmdc_calibration - board-specific calibration (routing delays) + * mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc) + * mx6_ddr_cfg - chip specific timing/layout details + */ + switch (board_model) { + default: + case GW51xx: + if (is_cpu_type(MXC_CPU_MX6Q)) + calib = &gw51xxq_mmdc_calib; + else + calib = &gw51xxdl_mmdc_calib; + break; + case GW52xx: + calib = &gw52xxdl_mmdc_calib; + break; + case GW53xx: + if (is_cpu_type(MXC_CPU_MX6Q)) + calib = &gw53xxq_mmdc_calib; + else + calib = &gw53xxdl_mmdc_calib; + break; + case GW54xx: + calib = &gw54xxq_mmdc_calib; + break; + } + + if (is_cpu_type(MXC_CPU_MX6Q)) + mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs, + &mx6dq_grp_ioregs); + else + mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs, + &mx6sdl_grp_ioregs); + mx6_dram_cfg(&sysinfo, calib, mem); +} + +/* + * called from C runtime startup code (arch/arm/lib/crt0.S:_main) + * - we have a stack and a place to store GD, both in SRAM + * - no variable global data is available + */ +void board_init_f(ulong dummy) +{ + struct ventana_board_info ventana_info; + int board_model; + + /* + * Zero out global data: + * - this shoudl be done by crt0.S + * - failure to zero it will cause i2c_setup to fail + */ + memset((void *)gd, 0, sizeof(struct global_data)); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + /* iomux and setup of i2c */ + board_early_init_f(); + i2c_setup_iomux(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* read/validate EEPROM info to determine board model and SDRAM cfg */ + board_model = read_eeprom(I2C_GSC, &ventana_info); + + /* provide some some default: 32bit 128MB */ + if (GW_UNKNOWN == board_model) { + ventana_info.sdram_width = 2; + ventana_info.sdram_size = 3; + } + + /* configure MMDC for SDRAM width/size and per-model calibration */ + spl_dram_init(8 << ventana_info.sdram_width, + 16 << ventana_info.sdram_size, + board_model); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +void reset_cpu(ulong addr) +{ +} |