17 files changed, 343 insertions, 94 deletions

diff --git a/board/keymile/km_arm/fpga_config.c b/board/keymile/km_arm/fpga_config.c
index cbfc7d2175..51a3cfe647 100644
--- a/board/keymile/km_arm/fpga_config.c
+++ b/board/keymile/km_arm/fpga_config.c
@@ -189,6 +189,31 @@ int wait_for_fpga_config(void)
 	return 0;
 }
 
+#if defined(KM_PCIE_RESET_MPP7)
+
+#define KM_PEX_RST_GPIO_PIN	7
+int fpga_reset(void)
+{
+	if (!check_boco2()) {
+		/* we do not have BOCO2, this is not really used */
+		return 0;
+	}
+
+	printf("PCIe reset through GPIO7: ");
+	/* apply PCIe reset via GPIO */
+	kw_gpio_set_valid(KM_PEX_RST_GPIO_PIN, 1);
+	kw_gpio_direction_output(KM_PEX_RST_GPIO_PIN, 1);
+	kw_gpio_set_value(KM_PEX_RST_GPIO_PIN, 0);
+	udelay(1000*10);
+	kw_gpio_set_value(KM_PEX_RST_GPIO_PIN, 1);
+
+	printf(" done\n");
+
+	return 0;
+}
+
+#else
+
 #define PRST1		0x4
 #define PCIE_RST	0x10
 #define TRAFFIC_RST	0x04
@@ -219,6 +244,7 @@ int fpga_reset(void)
 
 	return 0;
 }
+#endif
 
 /* the FPGA was configured, we configure the BOCO2 so that the EEPROM
  * is available from the Bobcat SPI bus */
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index 5620737bf0..35402c800b 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -46,7 +46,11 @@ static const u32 kwmpp_config[] = {
 	MPP4_NF_IO6,
 	MPP5_NF_IO7,
 	MPP6_SYSRST_OUTn,
+#if defined(KM_PCIE_RESET_MPP7)
+	MPP7_GPO,
+#else
 	MPP7_PEX_RST_OUTn,
+#endif
 #if defined(CONFIG_SYS_I2C_SOFT)
 	MPP8_GPIO,		/* SDA */
 	MPP9_GPIO,		/* SCL */
@@ -102,7 +106,7 @@ static const u32 kwmpp_config[] = {
 /*
  * Wait for startup OK from mgcoge3ne
  */
-int startup_allowed(void)
+static int startup_allowed(void)
 {
 	unsigned char buf;
 
@@ -164,7 +168,6 @@ static int initialize_unit_leds(void)
 	return 0;
 }
 
-#if defined(CONFIG_BOOTCOUNT_LIMIT)
 static void set_bootcount_addr(void)
 {
 	uchar buf[32];
@@ -173,7 +176,6 @@ static void set_bootcount_addr(void)
 	sprintf((char *)buf, "0x%x", bootcountaddr);
 	setenv("bootcountaddr", (char *)buf);
 }
-#endif
 
 int misc_init_r(void)
 {
@@ -210,9 +212,7 @@ int misc_init_r(void)
 
 	initialize_unit_leds();
 	set_km_env();
-#if defined(CONFIG_BOOTCOUNT_LIMIT)
 	set_bootcount_addr();
-#endif
 	return 0;
 }
 
@@ -322,15 +322,15 @@ void reset_phy(void)
 		return;
 
 	/* RGMII clk transition on data stable */
-	if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, &reg))
+	if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, &reg))
 		printf("Error reading PHY spec ctrl reg\n");
-	if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
-		reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
+	if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
+			 reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
 		printf("Error writing PHY spec ctrl reg\n");
 
 	/* leds setup */
-	if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
-		PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
+	if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
+			 PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
 		printf("Error writing PHY LED reg\n");
 
 	/* reset the phy */
diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile
index 3e69ee2f15..c57ca08e14 100644
--- a/board/keymile/kmp204x/Makefile
+++ b/board/keymile/kmp204x/Makefile
@@ -8,5 +8,5 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-y	:= kmp204x.o ddr.o eth.o tlb.o pci.o law.o \
+obj-y	:= kmp204x.o ddr.o eth.o tlb.o pci.o law.o qrio.o \
 	../common/common.o ../common/ivm.o
diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c
index f02642aece..95a19cdb2c 100644
--- a/board/keymile/kmp204x/kmp204x.c
+++ b/board/keymile/kmp204x/kmp204x.c
@@ -33,12 +33,51 @@ int checkboard(void)
 	return 0;
 }
 
-/* TODO: implement the I2C deblocking function */
-int i2c_make_abort(void)
+/* I2C deblocking uses the algorithm defined in board/keymile/common/common.c
+ * 2 dedicated QRIO GPIOs externally pull the SCL and SDA lines
+ * For I2C only the low state is activly driven and high state is pulled-up
+ * by a resistor. Therefore the deblock GPIOs are used
+ *  -> as an active output to drive a low state
+ *  -> as an open-drain input to have a pulled-up high state
+ */
+
+/* QRIO GPIOs used for deblocking */
+#define DEBLOCK_PORT1	GPIO_A
+#define DEBLOCK_SCL1	20
+#define DEBLOCK_SDA1	21
+
+/* By default deblock GPIOs are floating */
+static void i2c_deblock_gpio_cfg(void)
+{
+	/* set I2C bus 1 deblocking GPIOs input, but 0 value for open drain */
+	qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SCL1);
+	qrio_gpio_direction_input(DEBLOCK_PORT1, DEBLOCK_SDA1);
+
+	qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, 0);
+	qrio_set_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, 0);
+}
+
+void set_sda(int state)
+{
+	qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1, state);
+}
+
+void set_scl(int state)
+{
+	qrio_set_opendrain_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1, state);
+}
+
+int get_sda(void)
+{
+	return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SDA1);
+}
+
+int get_scl(void)
 {
-	return 1;
+	return qrio_get_gpio(DEBLOCK_PORT1, DEBLOCK_SCL1);
 }
 
+
 #define ZL30158_RST	8
 #define ZL30343_RST	9
 
@@ -62,6 +101,7 @@ int board_early_init_f(void)
 
 int board_early_init_r(void)
 {
+	int ret = 0;
 	/* Flush d-cache and invalidate i-cache of any FLASH data */
 	flush_dcache();
 	invalidate_icache();
@@ -69,7 +109,11 @@ int board_early_init_r(void)
 	set_liodns();
 	setup_portals();
 
-	return 0;
+	ret = trigger_fpga_config();
+	if (ret)
+		printf("error triggering PCIe FPGA config\n");
+
+	return ret;
 }
 
 unsigned long get_board_sys_clk(unsigned long dummy)
@@ -77,80 +121,12 @@ unsigned long get_board_sys_clk(unsigned long dummy)
 	return 66666666;
 }
 
-#define WDMASK_OFF	0x16
-
-static void qrio_wdmask(u8 bit, bool wden)
-{
-	u16 wdmask;
-	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
-
-	wdmask = in_be16(qrio_base + WDMASK_OFF);
-
-	if (wden)
-		wdmask |= (1 << bit);
-	else
-		wdmask &= ~(1 << bit);
-
-	out_be16(qrio_base + WDMASK_OFF, wdmask);
-}
-
-#define PRST_OFF	0x1a
-
-void qrio_prst(u8 bit, bool en, bool wden)
-{
-	u16 prst;
-	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
-
-	qrio_wdmask(bit, wden);
-
-	prst = in_be16(qrio_base + PRST_OFF);
-
-	if (en)
-		prst &= ~(1 << bit);
-	else
-		prst |= (1 << bit);
-
-	out_be16(qrio_base + PRST_OFF, prst);
-}
-
-#define PRSTCFG_OFF	0x1c
-
-void qrio_prstcfg(u8 bit, u8 mode)
-{
-	u32 prstcfg;
-	u8 i;
-	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
-
-	prstcfg = in_be32(qrio_base + PRSTCFG_OFF);
-
-	for (i = 0; i < 2; i++) {
-		if (mode & (1<<i))
-			set_bit(2*bit+i, &prstcfg);
-		else
-			clear_bit(2*bit+i, &prstcfg);
-	}
-
-	out_be32(qrio_base + PRSTCFG_OFF, prstcfg);
-}
-
-
-#define BOOTCOUNT_OFF	0x12
-
-void bootcount_store(ulong counter)
+int misc_init_f(void)
 {
-	u8 val;
-	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
-
-	val = (counter <= 255) ? (u8)counter : 255;
-	out_8(qrio_base + BOOTCOUNT_OFF, val);
-}
+	/* configure QRIO pis for i2c deblocking */
+	i2c_deblock_gpio_cfg();
 
-ulong bootcount_load(void)
-{
-	u8 val;
-	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
-	val = in_8(qrio_base + BOOTCOUNT_OFF);
-	return val;
+	return 0;
 }
 
 #define NUM_SRDS_BANKS	2
diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h
index b6ba672413..0267596e4e 100644
--- a/board/keymile/kmp204x/kmp204x.h
+++ b/board/keymile/kmp204x/kmp204x.h
@@ -5,6 +5,16 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
+/* QRIO GPIO ports */
+#define GPIO_A			0x40
+#define GPIO_B			0x60
+
+int qrio_get_gpio(u8 port_off, u8 gpio_nr);
+void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val);
+void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value);
+void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value);
+void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr);
+
 #define PRSTCFG_POWUP_UNIT_CORE_RST	0x0
 #define PRSTCFG_POWUP_UNIT_RST		0x1
 #define PRSTCFG_POWUP_RST		0x3
diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg
index f38dcf9c8c..9af8bd5b57 100644
--- a/board/keymile/kmp204x/pbi.cfg
+++ b/board/keymile/kmp204x/pbi.cfg
@@ -8,6 +8,16 @@
 #
 
 #PBI commands
+#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
+#Freescale's errarta sheet suggests it may be done with PBI
+09000010 00000000
+09000014 00000000
+09000018 81d00000
+09021008 0000f000
+09021028 0000f000
+09021048 0000f000
+09021068 0000f000
+09000018 00000000
 #Initialize CPC1 as 1MB SRAM
 09010000 00200400
 09138000 00000000
diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c
index ec20c8afb4..a484eb5749 100644
--- a/board/keymile/kmp204x/pci.c
+++ b/board/keymile/kmp204x/pci.c
@@ -14,18 +14,103 @@
 #include <libfdt.h>
 #include <fdt_support.h>
 #include <asm/fsl_serdes.h>
+#include <asm/errno.h>
 
 #include "kmp204x.h"
 
+#define PROM_SEL_L	11
+/* control the PROM_SEL_L signal*/
+static void toggle_fpga_eeprom_bus(bool cpu_own)
+{
+	qrio_gpio_direction_output(GPIO_A, PROM_SEL_L, !cpu_own);
+}
+
+#define CONF_SEL_L	10
+#define FPGA_PROG_L	19
+#define FPGA_DONE	18
+#define FPGA_INIT_L	17
+
+int trigger_fpga_config(void)
+{
+	int ret = 0, init_l;
+	/* approx 10ms */
+	u32 timeout = 10000;
+
+	/* make sure the FPGA_can access the EEPROM */
+	toggle_fpga_eeprom_bus(false);
+
+	/* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
+	qrio_gpio_direction_output(GPIO_A, CONF_SEL_L, 0);
+
+	/* trigger the config start */
+	qrio_gpio_direction_output(GPIO_A, FPGA_PROG_L, 0);
+
+	/* small delay for INIT_L line */
+	udelay(10);
+
+	/* wait for FPGA_INIT to be asserted */
+	do {
+		init_l = qrio_get_gpio(GPIO_A, FPGA_INIT_L);
+		if (timeout-- == 0) {
+			printf("FPGA_INIT timeout\n");
+			ret = -EFAULT;
+			break;
+		}
+		udelay(10);
+	} while (init_l);
+
+	/* deassert FPGA_PROG, config should start */
+	qrio_set_gpio(GPIO_A, FPGA_PROG_L, 1);
+
+	return ret;
+}
+
+/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
+static int wait_for_fpga_config(void)
+{
+	int ret = 0, done;
+	/* approx 5 s */
+	u32 timeout = 500000;
+
+	printf("PCIe FPGA config:");
+	do {
+		done = qrio_get_gpio(GPIO_A, FPGA_DONE);
+		if (timeout-- == 0) {
+			printf(" FPGA_DONE timeout\n");
+			ret = -EFAULT;
+			goto err_out;
+		}
+		udelay(10);
+	} while (!done);
+
+	printf(" done\n");
+
+err_out:
+	/* deactive CONF_SEL and give the CPU conf EEPROM access */
+	qrio_set_gpio(GPIO_A, CONF_SEL_L, 1);
+	toggle_fpga_eeprom_bus(true);
+
+	return ret;
+}
+
 #define PCIE_SW_RST	14
+#define PEXHC_SW_RST	13
 #define HOOPER_SW_RST	12
 
 void pci_init_board(void)
 {
+	/* first wait for the PCIe FPGA to be configured
+	 * it has been triggered earlier in board_early_init_r */
+	int ret = wait_for_fpga_config();
+	if (ret)
+		printf("error finishing PCIe FPGA config\n");
+
 	qrio_prst(PCIE_SW_RST, false, false);
+	qrio_prst(PEXHC_SW_RST, false, false);
 	qrio_prst(HOOPER_SW_RST, false, false);
 	/* Hooper is not direcly PCIe capable */
 	mdelay(50);
+
 	fsl_pcie_init_board(0);
 }
 
diff --git a/board/keymile/kmp204x/qrio.c b/board/keymile/kmp204x/qrio.c
new file mode 100644
index 0000000000..49f9aa2546
--- /dev/null
+++ b/board/keymile/kmp204x/qrio.c
@@ -0,0 +1,146 @@
+/*
+ * (C) Copyright 2013 Keymile AG
+ * Valentin Longchamp <valentin.longchamp@keymile.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+
+#include "../common/common.h"
+#include "kmp204x.h"
+
+/* QRIO GPIO register offsets */
+#define DIRECT_OFF		0x18
+#define GPRT_OFF		0x1c
+
+int qrio_get_gpio(u8 port_off, u8 gpio_nr)
+{
+	u32 gprt;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	gprt = in_be32(qrio_base + port_off + GPRT_OFF);
+
+	return (gprt >> gpio_nr) & 1U;
+}
+
+void qrio_set_gpio(u8 port_off, u8 gpio_nr, bool value)
+{
+	u32 gprt, mask;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	mask = 1U << gpio_nr;
+
+	gprt = in_be32(qrio_base + port_off + GPRT_OFF);
+	if (value)
+		gprt |= mask;
+	else
+		gprt &= ~mask;
+
+	out_be32(qrio_base + port_off + GPRT_OFF, gprt);
+}
+
+void qrio_gpio_direction_output(u8 port_off, u8 gpio_nr, bool value)
+{
+	u32 direct, mask;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	mask = 1U << gpio_nr;
+
+	direct = in_be32(qrio_base + port_off + DIRECT_OFF);
+	direct |= mask;
+	out_be32(qrio_base + port_off + DIRECT_OFF, direct);
+
+	qrio_set_gpio(port_off, gpio_nr, value);
+}
+
+void qrio_gpio_direction_input(u8 port_off, u8 gpio_nr)
+{
+	u32 direct, mask;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	mask = 1U << gpio_nr;
+
+	direct = in_be32(qrio_base + port_off + DIRECT_OFF);
+	direct &= ~mask;
+	out_be32(qrio_base + port_off + DIRECT_OFF, direct);
+}
+
+void qrio_set_opendrain_gpio(u8 port_off, u8 gpio_nr, u8 val)
+{
+	u32 direct, mask;
+
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	mask = 1U << gpio_nr;
+
+	direct = in_be32(qrio_base + port_off + DIRECT_OFF);
+	if (val == 0)
+		/* set to output -> GPIO drives low */
+		direct |= mask;
+	else
+		/* set to input -> GPIO floating */
+		direct &= ~mask;
+
+	out_be32(qrio_base + port_off + DIRECT_OFF, direct);
+}
+
+#define WDMASK_OFF	0x16
+
+static void qrio_wdmask(u8 bit, bool wden)
+{
+	u16 wdmask;
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	wdmask = in_be16(qrio_base + WDMASK_OFF);
+
+	if (wden)
+		wdmask |= (1 << bit);
+	else
+		wdmask &= ~(1 << bit);
+
+	out_be16(qrio_base + WDMASK_OFF, wdmask);
+}
+
+#define PRST_OFF	0x1a
+
+void qrio_prst(u8 bit, bool en, bool wden)
+{
+	u16 prst;
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	qrio_wdmask(bit, wden);
+
+	prst = in_be16(qrio_base + PRST_OFF);
+
+	if (en)
+		prst &= ~(1 << bit);
+	else
+		prst |= (1 << bit);
+
+	out_be16(qrio_base + PRST_OFF, prst);
+}
+
+#define PRSTCFG_OFF	0x1c
+
+void qrio_prstcfg(u8 bit, u8 mode)
+{
+	u32 prstcfg;
+	u8 i;
+	void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE;
+
+	prstcfg = in_be32(qrio_base + PRSTCFG_OFF);
+
+	for (i = 0; i < 2; i++) {
+		if (mode & (1<<i))
+			set_bit(2*bit+i, &prstcfg);
+		else
+			clear_bit(2*bit+i, &prstcfg);
+	}
+
+	out_be32(qrio_base + PRSTCFG_OFF, prstcfg);
+}
diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg
index f2b7fe3d42..2d4c48cb9c 100644
--- a/board/keymile/kmp204x/rcw_kmp204x.cfg
+++ b/board/keymile/kmp204x/rcw_kmp204x.cfg
@@ -7,5 +7,5 @@ aa55aa55 010e0100
 #64 bytes RCW data
 14600000 00000000 28200000 00000000
 148E70CF CFC02000 58000000 41000000
-00000000 00000000 00000000 F4428002
+00000000 00000000 00000000 F0428002
 00000000 00000000 00000000 00000000
diff --git a/board/keymile/scripts/develop-arm.txt b/board/keymile/scripts/develop-arm.txt
index 922afea277..d3c974f1f9 100644
--- a/board/keymile/scripts/develop-arm.txt
+++ b/board/keymile/scripts/develop-arm.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=true
diff --git a/board/keymile/scripts/develop-common.txt b/board/keymile/scripts/develop-common.txt
index a6bb1b1d4a..a80812a5d0 100644
--- a/board/keymile/scripts/develop-common.txt
+++ b/board/keymile/scripts/develop-common.txt
@@ -3,6 +3,7 @@ bootcmd=run ${subbootcmds}
 configure=run set_uimage; km_setboardid && saveenv && reset
 subbootcmds=tftpfdt tftpkernel nfsargs add_default boot
 nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${toolchain}/${arch}
+tftpfdt=if run set_fdthigh || test ${arch} != arm; then tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb; else true; fi
 tftpkernel=tftpboot ${load_addr_r} ${hostname}/${uimage}
 toolchain=/opt/eldk
 rootfssize=0
diff --git a/board/keymile/scripts/develop-ppc_82xx.txt b/board/keymile/scripts/develop-ppc_82xx.txt
index 909f6a3cee..d3c974f1f9 100644
--- a/board/keymile/scripts/develop-ppc_82xx.txt
+++ b/board/keymile/scripts/develop-ppc_82xx.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb
diff --git a/board/keymile/scripts/develop-ppc_8xx.txt b/board/keymile/scripts/develop-ppc_8xx.txt
index 909f6a3cee..d3c974f1f9 100644
--- a/board/keymile/scripts/develop-ppc_8xx.txt
+++ b/board/keymile/scripts/develop-ppc_8xx.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/develop-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb
diff --git a/board/keymile/scripts/ramfs-arm.txt b/board/keymile/scripts/ramfs-arm.txt
index 79974f1b70..87e984e179 100644
--- a/board/keymile/scripts/ramfs-arm.txt
+++ b/board/keymile/scripts/ramfs-arm.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=true
diff --git a/board/keymile/scripts/ramfs-common.txt b/board/keymile/scripts/ramfs-common.txt
index 502c8631f4..d79ad2e21b 100644
--- a/board/keymile/scripts/ramfs-common.txt
+++ b/board/keymile/scripts/ramfs-common.txt
@@ -7,6 +7,7 @@ nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}
 configure=run set_uimage; km_setboardid && saveenv && reset
 rootfsfile=${hostname}/rootfsImage
 setrootfsaddr=setexpr value ${pnvramaddr} - ${rootfssize} && setenv rootfsaddr 0x${value}
+tftpfdt=if run set_fdthigh || test ${arch} != arm; then tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb; else true; fi
 tftpkernel=tftpboot ${load_addr_r} ${hostname}/${uimage}
 tftpramfs=tftpboot ${rootfsaddr} ${hostname}/rootfsImage
 set_uimage=printenv uimage || setenv uimage uImage
diff --git a/board/keymile/scripts/ramfs-ppc_82xx.txt b/board/keymile/scripts/ramfs-ppc_82xx.txt
index 970927a2fa..87e984e179 100644
--- a/board/keymile/scripts/ramfs-ppc_82xx.txt
+++ b/board/keymile/scripts/ramfs-ppc_82xx.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb
diff --git a/board/keymile/scripts/ramfs-ppc_8xx.txt b/board/keymile/scripts/ramfs-ppc_8xx.txt
index 970927a2fa..87e984e179 100644
--- a/board/keymile/scripts/ramfs-ppc_8xx.txt
+++ b/board/keymile/scripts/ramfs-ppc_8xx.txt
@@ -1,2 +1 @@
 setup_debug_env=tftpboot 0x200000 scripts/ramfs-common.txt && env import -t 0x200000 ${filesize} && run configure
-tftpfdt=tftpboot ${fdt_addr_r} ${hostname}/${hostname}.dtb