diff options
Diffstat (limited to 'board/logicpd/zoom2/zoom2_serial.c')
| -rw-r--r-- | board/logicpd/zoom2/zoom2_serial.c | 130 |
1 files changed, 130 insertions, 0 deletions
diff --git a/board/logicpd/zoom2/zoom2_serial.c b/board/logicpd/zoom2/zoom2_serial.c new file mode 100644 index 0000000000..a3d777dfad --- /dev/null +++ b/board/logicpd/zoom2/zoom2_serial.c @@ -0,0 +1,130 @@ +/* + * Copyright (c) 2009 Wind River Systems, Inc. + * Tom Rix <Tom.Rix@windriver.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * This file was adapted from cpu/mpc5xxx/serial.c + * + */ + +#include <common.h> +#include <serial.h> +#include <ns16550.h> +#include <asm/arch/cpu.h> +#include "zoom2_serial.h" + +int quad_init_dev (unsigned long base) +{ + /* + * The Quad UART is on the debug board. + * Check if the debug board is attached before using the UART + */ + if (zoom2_debug_board_connected ()) { + NS16550_t com_port = (NS16550_t) base; + int baud_divisor = CONFIG_SYS_NS16550_CLK / 16 / + CONFIG_BAUDRATE; + + /* + * Zoom2 has a board specific initialization of its UART. + * This generic initialization has been copied from + * drivers/serial/ns16550.c. The macros have been expanded. + * + * Do the following instead of + * + * NS16550_init (com_port, clock_divisor); + */ + com_port->ier = 0x00; + + /* + * On Zoom2 board Set pre-scalar to 1 + * CLKSEL is GND => MCR[7] is 1 => preslr is 4 + * So change the prescl to 1 + */ + com_port->lcr = 0xBF; + com_port->fcr |= 0x10; + com_port->mcr &= 0x7F; + + /* This is generic ns16550.c setup */ + com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1; + com_port->dll = 0; + com_port->dlm = 0; + com_port->lcr = UART_LCR_8N1; + com_port->mcr = UART_MCR_DTR | UART_MCR_RTS; + com_port->fcr = UART_FCR_FIFO_EN | UART_FCR_RXSR | + UART_FCR_TXSR; + com_port->lcr = UART_LCR_BKSE | UART_LCR_8N1; + com_port->dll = baud_divisor & 0xff; + com_port->dlm = (baud_divisor >> 8) & 0xff; + com_port->lcr = UART_LCR_8N1; + } + /* + * We have to lie here, otherwise the board init code will hang + * on the check + */ + return 0; +} + +void quad_putc_dev (unsigned long base, const char c) +{ + if (zoom2_debug_board_connected ()) { + + if (c == '\n') + quad_putc_dev (base, '\r'); + + NS16550_putc ((NS16550_t) base, c); + } +} + +void quad_puts_dev (unsigned long base, const char *s) +{ + if (zoom2_debug_board_connected ()) { + while ((s != NULL) && (*s != '\0')) + quad_putc_dev (base, *s++); + } +} + +int quad_getc_dev (unsigned long base) +{ + if (zoom2_debug_board_connected ()) + return NS16550_getc ((NS16550_t) base); + else + return 0; +} + +int quad_tstc_dev (unsigned long base) +{ + if (zoom2_debug_board_connected ()) + return NS16550_tstc ((NS16550_t) base); + else + return 0; +} + +void quad_setbrg_dev (unsigned long base) +{ + if (zoom2_debug_board_connected ()) { + + int clock_divisor = CONFIG_SYS_NS16550_CLK / 16 / + CONFIG_BAUDRATE; + + NS16550_reinit ((NS16550_t) base, clock_divisor); + } +} + +QUAD_INIT (0) +QUAD_INIT (1) +QUAD_INIT (2) +QUAD_INIT (3) |