diff options
Diffstat (limited to 'board/mbx8xx/mbx8xx.c')
| -rw-r--r-- | board/mbx8xx/mbx8xx.c | 383 |
1 files changed, 0 insertions, 383 deletions
diff --git a/board/mbx8xx/mbx8xx.c b/board/mbx8xx/mbx8xx.c deleted file mode 100644 index 98c723f047..0000000000 --- a/board/mbx8xx/mbx8xx.c +++ /dev/null @@ -1,383 +0,0 @@ -/* - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * Board specific routines for the MBX - * - * - initialisation - * - interface to VPD data (mac address, clock speeds) - * - memory controller - * - serial io initialisation - * - ethernet io initialisation - * - * ----------------------------------------------------------------- - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <commproc.h> -#include <mpc8xx.h> -#include <net.h> -#include "dimm.h" -#include "vpd.h" -#include "csr.h" - -/* ------------------------------------------------------------------------- */ - -static const uint sdram_table_40[] = { - /* DRAM - single read. (offset 0 in upm RAM) - */ - 0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x30AF0C00, - 0xF1BF4805, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* DRAM - burst read. (offset 8 in upm RAM) - */ - 0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x03AF0C08, - 0x0CAF0C04, 0x03AF0C08, 0x0CAF0C04, 0x03AF0C08, - 0x0CAF0C04, 0x30AF0C00, 0xF3BF4805, 0xFFFFC005, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* DRAM - single write. (offset 18 in upm RAM) - */ - 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x33FF4804, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* DRAM - burst write. (offset 20 in upm RAM) - */ - 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C, - 0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C, - 0x0CFF0C00, 0x33FF4804, 0xFFFFC005, 0xFFFFC005, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* refresh (offset 30 in upm RAM) - */ - 0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004, - 0x3FFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* exception. (offset 3c in upm RAM) - */ - 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, -}; - -static const uint sdram_table_50[] = { - /* DRAM - single read. (offset 0 in upm RAM) - */ - 0xCFAFC004, 0x0FAFC404, 0x0CAF8C04, 0x10AF0C04, - 0xF0AF0C00, 0xF3BF4805, 0xFFFFC005, 0xFFFFC005, - - /* DRAM - burst read. (offset 8 in upm RAM) - */ - 0xCFAFC004, 0X0FAFC404, 0X0CAF8C04, 0X00AF0C04, - /* 0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C04, */ - 0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08, - 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08, 0X0CAF0C04, - /* 0X10AF0C04, 0XF0AFC000, 0XF3FF4805, 0XFFFFC005, */ - 0X10AF0C04, 0XF0AFC000, 0XF3BF4805, 0XFFFFC005, - - /* DRAM - single write. (offset 18 in upm RAM) - */ - 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x13FF4804, - 0xFFFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* DRAM - burst write. (offset 20 in upm RAM) - */ - 0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C, - 0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C, - 0x0CFF0C00, 0x13FF4804, 0xFFFFC004, 0xFFFFC005, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* refresh (offset 30 in upm RAM) - */ - 0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004, - 0x1FFFC004, 0xFFFFC004, 0xFFFFC005, 0xFFFFC005, - 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005, - - /* exception. (offset 3c in upm RAM) - */ - 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007, -}; - -/* ------------------------------------------------------------------------- */ - -#ifdef CONFIG_SYS_USE_OSCCLK -static unsigned int get_reffreq(void); -#endif -static unsigned int board_get_cpufreq(void); - -void mbx_init (void) -{ - volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immr->im_memctl; - ulong speed, plprcr, sccr; - ulong br0_32 = memctl->memc_br0 & 0x400; - - /* real-time clock status and control register */ - immr->im_sitk.sitk_rtcsck = KAPWR_KEY; - immr->im_sit.sit_rtcsc = 0x00C3; - - /* SIEL and SIMASK Registers (see MBX PRG 2-3) */ - immr->im_siu_conf.sc_simask = 0x00000000; - immr->im_siu_conf.sc_siel = 0xAAAA0000; - immr->im_siu_conf.sc_tesr = 0xFFFFFFFF; - - /* - * Prepare access to i2c bus. The MBX offers 3 devices on the i2c bus: - * 1. Vital Product Data (contains clock speeds, MAC address etc, see vpd.h) - * 2. RAM Specs (see dimm.h) - * 2. DIMM Specs (see dimm.h) - */ - vpd_init (); - - /* system clock and reset control register */ - immr->im_clkrstk.cark_sccrk = KAPWR_KEY; - sccr = immr->im_clkrst.car_sccr; - sccr &= SCCR_MASK; - sccr |= CONFIG_SYS_SCCR; - immr->im_clkrst.car_sccr = sccr; - - speed = board_get_cpufreq (); - -#if ((CONFIG_SYS_PLPRCR & PLPRCR_MF_MSK) != 0) - plprcr = CONFIG_SYS_PLPRCR; -#else - plprcr = immr->im_clkrst.car_plprcr; - plprcr &= PLPRCR_MF_MSK; /* isolate MF field */ - plprcr |= CONFIG_SYS_PLPRCR; /* reset control bits */ -#endif - -#ifdef CONFIG_SYS_USE_OSCCLK /* See doc/README.MBX ! */ - plprcr |= ((speed + get_reffreq() / 2) / refclock - 1) << 20; -#endif - - immr->im_clkrstk.cark_plprcrk = KAPWR_KEY; - immr->im_clkrst.car_plprcr = plprcr; - - /* - * preliminary setup of memory controller: - * - map Flash, otherwise configuration/status - * registers won't be accessible when read - * by board_init_f. - * - map NVRAM and configuation/status registers. - * - map pci registers. - * - DON'T map ram yet, this is done in initdram(). - */ - switch (speed / 1000000) { - case 40: - memctl->memc_br0 = 0xFE000000 | br0_32 | 1; - memctl->memc_or0 = 0xFF800930; - memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x920; - memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401; - break; - case 50: - memctl->memc_br0 = 0xFE000000 | br0_32 | 1; - memctl->memc_or0 = 0xFF800940; - memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x930; - memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401; - break; - default: - hang (); - break; - } -#ifdef CONFIG_USE_PCI - memctl->memc_or5 = CONFIG_SYS_PCIMEM_OR; - memctl->memc_br5 = CONFIG_SYS_PCIMEM_BASE | 0x001; - memctl->memc_or6 = CONFIG_SYS_PCIBRIDGE_OR; - memctl->memc_br6 = CONFIG_SYS_PCIBRIDGE_BASE | 0x001; -#endif - /* - * FIXME: I do not understand why I have to call this to - * initialise the control register here before booting from - * the PCMCIA card but if I do not the Linux kernel falls - * over in a big heap. If you can answer this question I - * would like to know about it. - */ - board_ether_init(); -} - -void board_serial_init (void) -{ - MBX_CSR1 &= ~(CSR1_COM1EN | CSR1_XCVRDIS); -} - -void board_ether_init (void) -{ - MBX_CSR1 &= ~(CSR1_EAEN | CSR1_ELEN); - MBX_CSR1 |= CSR1_ETEN | CSR1_TPEN | CSR1_FDDIS; -} - -static unsigned int board_get_cpufreq (void) -{ -#ifndef CONFIG_8xx_GCLK_FREQ - vpd_packet_t *packet; - ulong *p; - - packet = vpd_find_packet (VPD_PID_ICS); - p = (ulong *)packet->data; - return *p; -#else - return((unsigned int)CONFIG_8xx_GCLK_FREQ ); -#endif /* CONFIG_8xx_GCLK_FREQ */ -} - -#ifdef CONFIG_SYS_USE_OSCCLK -static unsigned int get_reffreq (void) -{ - vpd_packet_t *packet; - ulong *p; - - packet = vpd_find_packet (VPD_PID_RCS); - p = (ulong *)packet->data; - return *p; -} -#endif - -static void board_get_enetaddr(uchar *addr) -{ - int i; - vpd_packet_t *packet; - - packet = vpd_find_packet (VPD_PID_EA); - for (i = 0; i < 6; i++) - addr[i] = packet->data[i]; -} - -int misc_init_r(void) -{ - uchar enetaddr[6]; - - if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { - board_get_enetaddr(enetaddr); - eth_setenv_enetaddr("ethaddr", enetaddr); - } - - return 0; -} - -/* - * Check Board Identity: - */ - -int checkboard (void) -{ - vpd_packet_t *packet; - int i; - const char *const fmt = - "\n *** Warning: Low Battery Status - %s Battery ***"; - - puts ("Board: "); - - packet = vpd_find_packet (VPD_PID_PID); - for (i = 0; i < packet->size; i++) { - serial_putc (packet->data[i]); - } - packet = vpd_find_packet (VPD_PID_MT); - for (i = 0; i < packet->size; i++) { - serial_putc (packet->data[i]); - } - serial_putc ('('); - packet = vpd_find_packet (VPD_PID_FAN); - for (i = 0; i < packet->size; i++) { - serial_putc (packet->data[i]); - } - serial_putc (')'); - - if (!(MBX_CSR2 & SR2_BATGD)) - printf (fmt, "On-Board"); - if (!(MBX_CSR2 & SR2_NVBATGD)) - printf (fmt, "NVRAM"); - - serial_putc ('\n'); - - return (0); -} - -/* ------------------------------------------------------------------------- */ - -static ulong get_ramsize (dimm_t * dimm) -{ - ulong size = 0; - - if (dimm->fmt == 1 || dimm->fmt == 2 || dimm->fmt == 3 - || dimm->fmt == 4) { - size = (1 << (dimm->n_row + dimm->n_col)) * dimm->n_banks * - ((dimm->data_w_hi << 8 | dimm->data_w_lo) / 8); - } - - return size; -} - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - unsigned long ram_sz = 0; - unsigned long dimm_sz = 0; - dimm_t vpd_dimm, vpd_dram; - unsigned int speed = board_get_cpufreq () / 1000000; - - if (vpd_read (0xa2, (uchar *) & vpd_dimm, sizeof (vpd_dimm), 0) > 0) { - dimm_sz = get_ramsize (&vpd_dimm); - } - if (vpd_read (0xa6, (uchar *) & vpd_dram, sizeof (vpd_dram), 0) > 0) { - ram_sz = get_ramsize (&vpd_dram); - } - - /* - * Only initialize memory controller when running from FLASH. - * When running from RAM, don't touch it. - */ - if ((ulong) initdram & 0xff000000) { - ulong dimm_bank; - ulong br0_32 = memctl->memc_br0 & 0x400; - - switch (speed) { - case 40: - upmconfig (UPMA, (uint *) sdram_table_40, - sizeof (sdram_table_40) / sizeof (uint)); - memctl->memc_mptpr = 0x0200; - memctl->memc_mamr = dimm_sz ? 0x06801000 : 0x13801000; - memctl->memc_or7 = 0xff800930; - memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1; - break; - case 50: - upmconfig (UPMA, (uint *) sdram_table_50, - sizeof (sdram_table_50) / sizeof (uint)); - memctl->memc_mptpr = 0x0200; - memctl->memc_mamr = dimm_sz ? 0x08801000 : 0x1880100; - memctl->memc_or7 = 0xff800940; - memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1; - break; - default: - hang (); - break; - } - - /* now map ram and dimm, largest one first */ - dimm_bank = dimm_sz / 2; - if (!dimm_sz) { - memctl->memc_or1 = ~(ram_sz - 1) | 0x400; - memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81; - memctl->memc_br2 = 0; - memctl->memc_br3 = 0; - } else if (ram_sz > dimm_bank) { - memctl->memc_or1 = ~(ram_sz - 1) | 0x400; - memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81; - memctl->memc_or2 = ~(dimm_bank - 1) | 0x400; - memctl->memc_br2 = (CONFIG_SYS_SDRAM_BASE + ram_sz) | 0x81; - memctl->memc_or3 = ~(dimm_bank - 1) | 0x400; - memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + ram_sz + dimm_bank) \ - | 0x81; - } else { - memctl->memc_or2 = ~(dimm_bank - 1) | 0x400; - memctl->memc_br2 = CONFIG_SYS_SDRAM_BASE | 0x81; - memctl->memc_or3 = ~(dimm_bank - 1) | 0x400; - memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + dimm_bank) | 0x81; - memctl->memc_or1 = ~(ram_sz - 1) | 0x400; - memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE + dimm_sz) | 0x81; - } - } - - return ram_sz + dimm_sz; -} |