diff options
Diffstat (limited to 'board/renesas/porter/porter.c')
| -rw-r--r-- | board/renesas/porter/porter.c | 228 |
1 files changed, 228 insertions, 0 deletions
diff --git a/board/renesas/porter/porter.c b/board/renesas/porter/porter.c new file mode 100644 index 0000000000..b5378defa8 --- /dev/null +++ b/board/renesas/porter/porter.c @@ -0,0 +1,228 @@ +/* + * board/renesas/porter/porter.c + * + * Copyright (C) 2015 Renesas Electronics Corporation + * Copyright (C) 2015 Cogent Embedded, Inc. + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#include <common.h> +#include <malloc.h> +#include <dm.h> +#include <dm/platform_data/serial_sh.h> +#include <asm/processor.h> +#include <asm/mach-types.h> +#include <asm/io.h> +#include <asm/errno.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/arch/rmobile.h> +#include <asm/arch/rcar-mstp.h> +#include <asm/arch/sh_sdhi.h> +#include <netdev.h> +#include <miiphy.h> +#include <i2c.h> +#include <div64.h> +#include "qos.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define CLK2MHZ(clk) (clk / 1000 / 1000) +void s_init(void) +{ + struct rcar_rwdt *rwdt = (struct rcar_rwdt *)RWDT_BASE; + struct rcar_swdt *swdt = (struct rcar_swdt *)SWDT_BASE; + u32 stc; + + /* Watchdog init */ + writel(0xA5A5A500, &rwdt->rwtcsra); + writel(0xA5A5A500, &swdt->swtcsra); + + /* CPU frequency setting. Set to 1.5GHz */ + stc = ((1500 / CLK2MHZ(CONFIG_SYS_CLK_FREQ)) - 1) << PLL0_STC_BIT; + clrsetbits_le32(PLL0CR, PLL0_STC_MASK, stc); + + /* QoS */ + qos_init(); +} + +#define TMU0_MSTP125 (1 << 25) +#define SDHI0_MSTP314 (1 << 14) +#define SDHI2_MSTP311 (1 << 11) +#define SCIF0_MSTP721 (1 << 21) +#define ETHER_MSTP813 (1 << 13) + +#define SD2CKCR 0xE615026C +#define SD_97500KHZ 0x7 + +int board_early_init_f(void) +{ + mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125); + + /* SCIF0 */ + mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721); + + /* ETHER */ + mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813); + + /* SDHI */ + mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314 | SDHI2_MSTP311); + + /* + * SD0 clock is set to 97.5MHz by default. + * Set SD2 to the 97.5MHz as well. + */ + writel(SD_97500KHZ, SD2CKCR); + + return 0; +} + +/* LSI pin pull-up control */ +#define PUPR5 0xe6060114 +#define PUPR5_ETH 0x3FFC0000 +#define PUPR5_ETH_MAGIC (1 << 27) +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + /* Init PFC controller */ + r8a7791_pinmux_init(); + + /* Ether Enable */ + gpio_request(GPIO_FN_ETH_CRS_DV, NULL); + gpio_request(GPIO_FN_ETH_RX_ER, NULL); + gpio_request(GPIO_FN_ETH_RXD0, NULL); + gpio_request(GPIO_FN_ETH_RXD1, NULL); + gpio_request(GPIO_FN_ETH_LINK, NULL); + gpio_request(GPIO_FN_ETH_REFCLK, NULL); + gpio_request(GPIO_FN_ETH_MDIO, NULL); + gpio_request(GPIO_FN_ETH_TXD1, NULL); + gpio_request(GPIO_FN_ETH_TX_EN, NULL); + gpio_request(GPIO_FN_ETH_TXD0, NULL); + gpio_request(GPIO_FN_ETH_MDC, NULL); + gpio_request(GPIO_FN_IRQ0, NULL); + + mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH & ~PUPR5_ETH_MAGIC); + gpio_request(GPIO_GP_5_22, NULL); /* PHY_RST */ + mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH_MAGIC); + + gpio_direction_output(GPIO_GP_5_22, 0); + mdelay(20); + gpio_set_value(GPIO_GP_5_22, 1); + udelay(1); + + return 0; +} + +#define CXR24 0xEE7003C0 /* MAC address high register */ +#define CXR25 0xEE7003C8 /* MAC address low register */ +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_SH_ETHER + int ret = -ENODEV; + u32 val; + unsigned char enetaddr[6]; + + ret = sh_eth_initialize(bis); + if (!eth_getenv_enetaddr("ethaddr", enetaddr)) + return ret; + + /* Set Mac address */ + val = enetaddr[0] << 24 | enetaddr[1] << 16 | + enetaddr[2] << 8 | enetaddr[3]; + writel(val, CXR24); + + val = enetaddr[4] << 8 | enetaddr[5]; + writel(val, CXR25); + + return ret; +#else + return 0; +#endif +} + +int board_mmc_init(bd_t *bis) +{ + int ret = -ENODEV; + +#ifdef CONFIG_SH_SDHI + gpio_request(GPIO_FN_SD0_DATA0, NULL); + gpio_request(GPIO_FN_SD0_DATA1, NULL); + gpio_request(GPIO_FN_SD0_DATA2, NULL); + gpio_request(GPIO_FN_SD0_DATA3, NULL); + gpio_request(GPIO_FN_SD0_CLK, NULL); + gpio_request(GPIO_FN_SD0_CMD, NULL); + gpio_request(GPIO_FN_SD0_CD, NULL); + gpio_request(GPIO_FN_SD2_DATA0, NULL); + gpio_request(GPIO_FN_SD2_DATA1, NULL); + gpio_request(GPIO_FN_SD2_DATA2, NULL); + gpio_request(GPIO_FN_SD2_DATA3, NULL); + gpio_request(GPIO_FN_SD2_CLK, NULL); + gpio_request(GPIO_FN_SD2_CMD, NULL); + gpio_request(GPIO_FN_SD2_CD, NULL); + + /* SDHI 0 */ + gpio_request(GPIO_GP_2_12, NULL); + gpio_direction_output(GPIO_GP_2_12, 1); /* 1: 3.3V, 0: 1.8V */ + + ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0, + SH_SDHI_QUIRK_16BIT_BUF); + if (ret) + return ret; + + /* SDHI 2 */ + gpio_request(GPIO_GP_2_26, NULL); + gpio_direction_output(GPIO_GP_2_26, 1); /* 1: 3.3V, 0: 1.8V */ + + ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 2, 0); +#endif + return ret; +} + +int dram_init(void) +{ + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + + return 0; +} + +/* porter has KSZ8041RNLI */ +#define PHY_CONTROL1 0x1E +#define PHY_LED_MODE 0xC0000 +#define PHY_LED_MODE_ACK 0x4000 +int board_phy_config(struct phy_device *phydev) +{ + int ret = phy_read(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1); + ret &= ~PHY_LED_MODE; + ret |= PHY_LED_MODE_ACK; + ret = phy_write(phydev, MDIO_DEVAD_NONE, PHY_CONTROL1, (u16)ret); + + return 0; +} + +const struct rmobile_sysinfo sysinfo = { + CONFIG_RMOBILE_BOARD_STRING +}; + +void reset_cpu(ulong addr) +{ + u8 val; + + i2c_set_bus_num(2); /* PowerIC connected to ch2 */ + i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1); + val |= 0x02; + i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1); +} + +static const struct sh_serial_platdata serial_platdata = { + .base = SCIF0_BASE, + .type = PORT_SCIF, + .clk = CONFIG_P_CLK_FREQ, +}; + +U_BOOT_DEVICE(porter_serials) = { + .name = "serial_sh", + .platdata = &serial_platdata, +}; |