summaryrefslogtreecommitdiff
path: root/board/samtec
diff options
context:
space:
mode:
Diffstat (limited to 'board/samtec')
-rw-r--r--board/samtec/vining_2000/Kconfig12
-rw-r--r--board/samtec/vining_2000/MAINTAINERS6
-rw-r--r--board/samtec/vining_2000/Makefile4
-rw-r--r--board/samtec/vining_2000/imximage.cfg131
-rw-r--r--board/samtec/vining_2000/vining_2000.c521
5 files changed, 0 insertions, 674 deletions
diff --git a/board/samtec/vining_2000/Kconfig b/board/samtec/vining_2000/Kconfig
deleted file mode 100644
index 3447c27fa4..0000000000
--- a/board/samtec/vining_2000/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_SAMTEC_VINING_2000
-
-config SYS_BOARD
- default "vining_2000"
-
-config SYS_VENDOR
- default "samtec"
-
-config SYS_CONFIG_NAME
- default "vining_2000"
-
-endif
diff --git a/board/samtec/vining_2000/MAINTAINERS b/board/samtec/vining_2000/MAINTAINERS
deleted file mode 100644
index 027e52736f..0000000000
--- a/board/samtec/vining_2000/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-VINING_2000 BOARD
-M: Ingo Schroeck <open-source@samtec.de>
-S: Maintained
-F: board/samtec/vining_2000/
-F: include/configs/vining_2000.h
-F: configs/vining_2000_defconfig
diff --git a/board/samtec/vining_2000/Makefile b/board/samtec/vining_2000/Makefile
deleted file mode 100644
index 9650da711d..0000000000
--- a/board/samtec/vining_2000/Makefile
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-# (C) Copyright 2016 samtec automotive software & electronics gmbh
-
-obj-y := vining_2000.o
diff --git a/board/samtec/vining_2000/imximage.cfg b/board/samtec/vining_2000/imximage.cfg
deleted file mode 100644
index 3e4fcad8ea..0000000000
--- a/board/samtec/vining_2000/imximage.cfg
+++ /dev/null
@@ -1,131 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2016 samtec automotive software & electronics gmbh
- */
-
-#define __ASSEMBLY__
-#include <config.h>
-
-/* image version */
-
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi/sd/nand/onenand, qspi/nor
- */
-
-BOOT_FROM sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-
-/* Enable all clocks */
-DATA 4 0x020c4068 0xffffffff
-DATA 4 0x020c406c 0xffffffff
-DATA 4 0x020c4070 0xffffffff
-DATA 4 0x020c4074 0xffffffff
-DATA 4 0x020c4078 0xffffffff
-DATA 4 0x020c407c 0xffffffff
-DATA 4 0x020c4080 0xffffffff
-DATA 4 0x020c4084 0xffffffff
-
-/* IOMUX - DDR IO Type */
-DATA 4 0x020e0618 0x000c0000
-DATA 4 0x020e05fc 0x00000000
-
-/* Clock */
-DATA 4 0x020e032c 0x00000030
-
-/* Address */
-DATA 4 0x020e0300 0x00000028
-DATA 4 0x020e02fc 0x00000028
-DATA 4 0x020e05f4 0x00000028
-
-/* Control */
-DATA 4 0x020e0340 0x00000028
-
-DATA 4 0x020e0320 0x00000000
-DATA 4 0x020e0310 0x00000028
-DATA 4 0x020e0314 0x00000028
-DATA 4 0x020e0614 0x00000028
-
-/* Data Strobe */
-DATA 4 0x020e05f8 0x00020000
-DATA 4 0x020e0330 0x00000028
-DATA 4 0x020e0334 0x00000028
-DATA 4 0x020e0338 0x00000028
-DATA 4 0x020e033c 0x00000028
-
-/* Data */
-DATA 4 0x020e0608 0x00020000
-DATA 4 0x020e060c 0x00000028
-DATA 4 0x020e0610 0x00000028
-DATA 4 0x020e061c 0x00000028
-DATA 4 0x020e0620 0x00000028
-DATA 4 0x020e02ec 0x00000028
-DATA 4 0x020e02f0 0x00000028
-DATA 4 0x020e02f4 0x00000028
-DATA 4 0x020e02f8 0x00000028
-
-/* Calibrations - ZQ */
-DATA 4 0x021b0800 0xa1390003
-
-/* Write leveling */
-DATA 4 0x021b080c 0x00290025
-DATA 4 0x021b0810 0x00210022
-
-/* DQS Read Gate */
-DATA 4 0x021b083c 0x4142013a
-DATA 4 0x021b0840 0x012e0123
-
-/* Read/Write Delay */
-DATA 4 0x021b0848 0x43474949
-DATA 4 0x021b0850 0x38383c38
-
-/* Read data bit delay */
-DATA 4 0x021b081c 0x33333333
-DATA 4 0x021b0820 0x33333333
-DATA 4 0x021b0824 0x33333333
-DATA 4 0x021b0828 0x33333333
-
-/* Complete calibration by forced measurement */
-DATA 4 0x021b08b8 0x00000800
-
-/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */
-DATA 4 0x021b0004 0x0002002d
-DATA 4 0x021b0008 0x00333040
-DATA 4 0x021b000c 0x676b52f2
-DATA 4 0x021b0010 0x926e8b63
-DATA 4 0x021b0014 0x01ff00db
-DATA 4 0x021b0018 0x00011740
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b002c 0x000026d2
-DATA 4 0x021b0030 0x006b1023
-DATA 4 0x021b0040 0x0000005f
-DATA 4 0x021b0000 0x84190000
-
-/* Initialize MT41K256M16HA-125 - MR2 */
-DATA 4 0x021b001c 0x02008032
-/* MR3 */
-DATA 4 0x021b001c 0x00008033
-/* MR1 */
-DATA 4 0x021b001c 0x00048031
-/* MR0 */
-DATA 4 0x021b001c 0x15108030
-/* DDR device ZQ calibration */
-DATA 4 0x021b001c 0x04008040
-
-/* Final DDR setup, before operation start */
-DATA 4 0x021b0020 0x00007800
-DATA 4 0x021b0818 0x00022227
-DATA 4 0x021b001c 0x00000000
diff --git a/board/samtec/vining_2000/vining_2000.c b/board/samtec/vining_2000/vining_2000.c
deleted file mode 100644
index d82b3aeb31..0000000000
--- a/board/samtec/vining_2000/vining_2000.c
+++ /dev/null
@@ -1,521 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2016 samtec automotive software & electronics gmbh
- *
- * Author: Christoph Fritz <chf.fritz@googlemail.com>
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/io.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <linux/sizes.h>
-#include <common.h>
-#include <environment.h>
-#include <fsl_esdhc.h>
-#include <mmc.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <power/pmic.h>
-#include <power/pfuze100_pmic.h>
-#include <usb.h>
-#include <usb/ehci-ci.h>
-#include <pwm.h>
-#include <wait_bit.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PKE | \
- PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | \
- PAD_CTL_SRE_FAST)
-
-#define ENET_CLK_PAD_CTRL PAD_CTL_DSE_34ohm
-
-#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | \
- PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_HIGH | \
- PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_PKE | PAD_CTL_ODE | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm)
-
-#define USDHC_CLK_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST)
-
-#define USDHC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST)
-
-#define USDHC_RESET_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm)
-
-#define GPIO_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_PKE)
-
-int dram_init(void)
-{
- gd->ram_size = imx_ddr_size();
-
- return 0;
-}
-
-static iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
- MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
- MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_RESET_B__USDHC4_RESET_B | MUX_PAD_CTRL(USDHC_RESET_CTRL),
-};
-
-static iomux_v3_cfg_t const fec1_pads[] = {
- MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
- MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL) |
- MUX_MODE_SION,
- /* LAN8720 PHY Reset */
- MX6_PAD_RGMII1_TD3__GPIO5_IO_9 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const pwm_led_pads[] = {
- MX6_PAD_RGMII2_RD2__PWM2_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* green */
- MX6_PAD_RGMII2_TD2__PWM6_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* red */
- MX6_PAD_RGMII2_RD3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), /* blue */
-};
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-#define PHY_RESET IMX_GPIO_NR(5, 9)
-
-int board_eth_init(bd_t *bis)
-{
- struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
- int ret;
- unsigned char eth1addr[6];
-
- /* just to get secound mac address */
- imx_get_mac_from_fuse(1, eth1addr);
- if (!env_get("eth1addr") && is_valid_ethaddr(eth1addr))
- eth_env_set_enetaddr("eth1addr", eth1addr);
-
- imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-
- /*
- * Generate phy reference clock via pin IOMUX ENET_REF_CLK1/2 by erasing
- * ENET1/2_TX_CLK_DIR gpr1[14:13], so that reference clock is driven by
- * ref_enetpll0/1 and enable ENET1/2_TX_CLK output driver.
- */
- clrsetbits_le32(&iomuxc_regs->gpr[1],
- IOMUX_GPR1_FEC1_CLOCK_MUX2_SEL_MASK |
- IOMUX_GPR1_FEC2_CLOCK_MUX2_SEL_MASK,
- IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK |
- IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
-
- ret = enable_fec_anatop_clock(0, ENET_50MHZ);
- if (ret)
- goto eth_fail;
-
- /* reset phy */
- gpio_direction_output(PHY_RESET, 0);
- mdelay(16);
- gpio_set_value(PHY_RESET, 1);
- mdelay(1);
-
- ret = fecmxc_initialize_multi(bis, 0, CONFIG_FEC_MXC_PHYADDR,
- IMX_FEC_BASE);
- if (ret)
- goto eth_fail;
-
- return ret;
-
-eth_fail:
- printf("FEC MXC: %s:failed (%i)\n", __func__, ret);
- gpio_set_value(PHY_RESET, 0);
- return ret;
-}
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-/* I2C1 for PMIC */
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
- .gp = IMX_GPIO_NR(1, 0),
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
- .gp = IMX_GPIO_NR(1, 1),
- },
-};
-
-static struct pmic *pfuze_init(unsigned char i2cbus)
-{
- struct pmic *p;
- int ret;
- u32 reg;
-
- ret = power_pfuze100_init(i2cbus);
- if (ret)
- return NULL;
-
- p = pmic_get("PFUZE100");
- ret = pmic_probe(p);
- if (ret)
- return NULL;
-
- pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
- printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
-
- /* Set SW1AB stanby volage to 0.975V */
- pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
- reg &= ~SW1x_STBY_MASK;
- reg |= SW1x_0_975V;
- pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
-
- /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
- reg &= ~SW1xCONF_DVSSPEED_MASK;
- reg |= SW1xCONF_DVSSPEED_4US;
- pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
-
- /* Set SW1C standby voltage to 0.975V */
- pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
- reg &= ~SW1x_STBY_MASK;
- reg |= SW1x_0_975V;
- pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
-
- /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
- pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
- reg &= ~SW1xCONF_DVSSPEED_MASK;
- reg |= SW1xCONF_DVSSPEED_4US;
- pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
-
- return p;
-}
-
-static int pfuze_mode_init(struct pmic *p, u32 mode)
-{
- unsigned char offset, i, switch_num;
- u32 id;
- int ret;
-
- pmic_reg_read(p, PFUZE100_DEVICEID, &id);
- id = id & 0xf;
-
- if (id == 0) {
- switch_num = 6;
- offset = PFUZE100_SW1CMODE;
- } else if (id == 1) {
- switch_num = 4;
- offset = PFUZE100_SW2MODE;
- } else {
- printf("Not supported, id=%d\n", id);
- return -EINVAL;
- }
-
- ret = pmic_reg_write(p, PFUZE100_SW1ABMODE, mode);
- if (ret < 0) {
- printf("Set SW1AB mode error!\n");
- return ret;
- }
-
- for (i = 0; i < switch_num - 1; i++) {
- ret = pmic_reg_write(p, offset + i * SWITCH_SIZE, mode);
- if (ret < 0) {
- printf("Set switch 0x%x mode error!\n",
- offset + i * SWITCH_SIZE);
- return ret;
- }
- }
-
- return ret;
-}
-
-int power_init_board(void)
-{
- struct pmic *p;
- int ret;
-
- p = pfuze_init(I2C_PMIC);
- if (!p)
- return -ENODEV;
-
- ret = pfuze_mode_init(p, APS_PFM);
- if (ret < 0)
- return ret;
-
- return 0;
-}
-
-#ifdef CONFIG_USB_EHCI_MX6
-static iomux_v3_cfg_t const usb_otg_pads[] = {
- /* OGT1 */
- MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* OTG2 */
- MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)
-};
-
-static void setup_iomux_usb(void)
-{
- imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
- ARRAY_SIZE(usb_otg_pads));
-}
-
-int board_usb_phy_mode(int port)
-{
- if (port == 1)
- return USB_INIT_HOST;
- else
- return usb_phy_mode(port);
-}
-#endif
-
-#ifdef CONFIG_PWM_IMX
-static int set_pwm_leds(void)
-{
- int ret;
-
- imx_iomux_v3_setup_multiple_pads(pwm_led_pads,
- ARRAY_SIZE(pwm_led_pads));
- /* enable backlight PWM 2, green LED */
- ret = pwm_init(1, 0, 0);
- if (ret)
- goto error;
- /* duty cycle 200ns, period: 8000ns */
- ret = pwm_config(1, 200, 8000);
- if (ret)
- goto error;
- ret = pwm_enable(1);
- if (ret)
- goto error;
-
- /* enable backlight PWM 1, blue LED */
- ret = pwm_init(0, 0, 0);
- if (ret)
- goto error;
- /* duty cycle 200ns, period: 8000ns */
- ret = pwm_config(0, 200, 8000);
- if (ret)
- goto error;
- ret = pwm_enable(0);
- if (ret)
- goto error;
-
- /* enable backlight PWM 6, red LED */
- ret = pwm_init(5, 0, 0);
- if (ret)
- goto error;
- /* duty cycle 200ns, period: 8000ns */
- ret = pwm_config(5, 200, 8000);
- if (ret)
- goto error;
- ret = pwm_enable(5);
-
-error:
- return ret;
-}
-#else
-static int set_pwm_leds(void)
-{
- return 0;
-}
-#endif
-
-#define ADCx_HC0 0x00
-#define ADCx_HS 0x08
-#define ADCx_HS_C0 BIT(0)
-#define ADCx_R0 0x0c
-#define ADCx_CFG 0x14
-#define ADCx_CFG_SWMODE 0x308
-#define ADCx_GC 0x18
-#define ADCx_GC_CAL BIT(7)
-
-static int read_adc(u32 *val)
-{
- int ret;
- void __iomem *b = map_physmem(ADC1_BASE_ADDR, 0x100, MAP_NOCACHE);
-
- /* use software mode */
- writel(ADCx_CFG_SWMODE, b + ADCx_CFG);
-
- /* start auto calibration */
- setbits_le32(b + ADCx_GC, ADCx_GC_CAL);
- ret = wait_for_bit_le32(b + ADCx_GC, ADCx_GC_CAL, ADCx_GC_CAL, 10, 0);
- if (ret)
- goto adc_exit;
-
- /* start conversion */
- writel(0, b + ADCx_HC0);
-
- /* wait for conversion */
- ret = wait_for_bit_le32(b + ADCx_HS, ADCx_HS_C0, ADCx_HS_C0, 10, 0);
- if (ret)
- goto adc_exit;
-
- /* read result */
- *val = readl(b + ADCx_R0);
-
-adc_exit:
- if (ret)
- printf("ADC failure (ret=%i)\n", ret);
- unmap_physmem(b, MAP_NOCACHE);
- return ret;
-}
-
-#define VAL_UPPER 2498
-#define VAL_LOWER 1550
-
-static int set_pin_state(void)
-{
- u32 val;
- int ret;
-
- ret = read_adc(&val);
- if (ret)
- return ret;
-
- if (val >= VAL_UPPER)
- env_set("pin_state", "connected");
- else if (val < VAL_UPPER && val > VAL_LOWER)
- env_set("pin_state", "open");
- else
- env_set("pin_state", "button");
-
- return ret;
-}
-
-int board_late_init(void)
-{
- int ret;
-
- ret = set_pwm_leds();
- if (ret)
- return ret;
-
- ret = set_pin_state();
-
- return ret;
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
- setup_iomux_usb();
-
- return 0;
-}
-
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC4_BASE_ADDR, 0, 8},
- {USDHC2_BASE_ADDR, 0, 4},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
- if (cfg->esdhc_base == USDHC4_BASE_ADDR)
- return 1;
- if (cfg->esdhc_base == USDHC2_BASE_ADDR)
- return !gpio_get_value(USDHC2_CD_GPIO);
-
- return -EINVAL;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int ret;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 USDHC4
- * mmc1 USDHC2
- */
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
- if (ret) {
- printf("Warning: failed to initialize USDHC4\n");
- return ret;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
- if (ret) {
- printf("Warning: failed to initialize USDHC2\n");
- return ret;
- }
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_SYS_I2C_MXC
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
-#endif
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: VIN|ING 2000\n");
-
- return 0;
-}
generated by cgit (git 2.34.1) at 2024-12-28 11:27:52 +0000