diff options
Diffstat (limited to 'board/sunxi/Kconfig')
| -rw-r--r-- | board/sunxi/Kconfig | 58 |
1 files changed, 58 insertions, 0 deletions
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 4a2158988f..9cf54e51ac 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -149,6 +149,16 @@ config SPL_FEL bool "SPL/FEL mode support" depends on SPL default n + help + This enables support for Fast Early Loader (FEL) mode. This + allows U-Boot to be loaded to the board over USB by the on-chip + boot rom. U-Boot should be sent in two parts: SPL first, with + 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with + 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option + shrinks the amount of SRAM available to SPL, so only enable it if + you need FEL. Note that enabling this option only allows FEL to be + used; it is still possible to boot U-Boot from boot media. U-Boot + SPL detects when it is being loaded using FEL. config UART0_PORT_F bool "UART0 on MicroSD breakout board" @@ -213,6 +223,14 @@ config USB0_VBUS_PIN Set the Vbus enable pin for usb0 (otg). This takes a string in the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. +config USB0_VBUS_DET + string "Vbus detect pin for usb0 (otg)" + depends on USB_MUSB_SUNXI + default "" + ---help--- + Set the Vbus detect pin for usb0 (otg). This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + config USB1_VBUS_PIN string "Vbus enable pin for usb1 (ehci0)" default "PH6" if MACH_SUN4I || MACH_SUN7I @@ -302,6 +320,14 @@ config VIDEO_LCD_POWER Set the power enable pin for the LCD panel. This takes a string in the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. +config VIDEO_LCD_RESET + string "LCD panel reset pin" + depends on VIDEO + default "" + ---help--- + Set the reset pin for the LCD panel. This takes a string in the format + understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + config VIDEO_LCD_BL_EN string "LCD panel backlight enable pin" depends on VIDEO @@ -326,6 +352,30 @@ config VIDEO_LCD_BL_PWM_ACTIVE_LOW ---help--- Set this if the backlight pwm output is active low. +config VIDEO_LCD_PANEL_I2C + bool "LCD panel needs to be configured via i2c" + depends on VIDEO + default m + ---help--- + Say y here if the LCD panel needs to be configured via i2c. This + will add a bitbang i2c controller using gpios to talk to the LCD. + +config VIDEO_LCD_PANEL_I2C_SDA + string "LCD panel i2c interface SDA pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG12" + ---help--- + Set the SDA pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + +config VIDEO_LCD_PANEL_I2C_SCL + string "LCD panel i2c interface SCL pin" + depends on VIDEO_LCD_PANEL_I2C + default "PG10" + ---help--- + Set the SCL pin for the LCD i2c interface. This takes a string in the + format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. + # Note only one of these may be selected at a time! But hidden choices are # not supported by Kconfig @@ -364,6 +414,14 @@ config VIDEO_LCD_PANEL_HITACHI_TX18D42VM ---help--- 7.85" 1024x768 Hitachi tx18d42vm LCD panel support +config VIDEO_LCD_TL059WV5C0 + bool "tl059wv5c0 LCD panel" + select VIDEO_LCD_PANEL_I2C + select VIDEO_LCD_IF_PARALLEL + ---help--- + 6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and + Aigo M60/M608/M606 tablets. + endchoice |