diff options
Diffstat (limited to 'board/sunxi/board.c')
| -rw-r--r-- | board/sunxi/board.c | 50 |
1 files changed, 12 insertions, 38 deletions
diff --git a/board/sunxi/board.c b/board/sunxi/board.c index ed60e74808..afed6a31ca 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -31,7 +31,6 @@ #include <asm/arch/usb_phy.h> #include <asm/gpio.h> #include <asm/io.h> -#include <linux/usb/musb.h> #include <net.h> #if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD) @@ -294,21 +293,19 @@ int board_mmc_init(bd_t *bis) return -1; #endif -#if CONFIG_MMC_SUNXI_SLOT == 0 && CONFIG_MMC_SUNXI_SLOT_EXTRA == 2 +#if !defined(CONFIG_SPL_BUILD) && CONFIG_MMC_SUNXI_SLOT_EXTRA == 2 /* - * Both mmc0 and mmc2 are bootable, figure out where we're booting - * from. Try mmc0 first, just like the brom does. + * On systems with an emmc (mmc2), figure out if we are booting from + * the emmc and if we are make it "mmc dev 0" so that boot.scr, etc. + * are searched there first. Note we only do this for u-boot proper, + * not for the SPL, see spl_boot_device(). */ - if (mmc_getcd(mmc0) && mmc_init(mmc0) == 0 && - mmc0->block_dev.block_read(0, 16, 1, buf) == 1) { - buf[12] = 0; - if (strcmp(&buf[4], "eGON.BT0") == 0) - return 0; + if (!sunxi_mmc_has_egon_boot_signature(mmc0) && + sunxi_mmc_has_egon_boot_signature(mmc1)) { + /* Booting from emmc / mmc2, swap */ + mmc0->block_dev.dev = 1; + mmc1->block_dev.dev = 0; } - - /* no bootable card in mmc0, so we must be booting from mmc2, swap */ - mmc0->block_dev.dev = 1; - mmc1->block_dev.dev = 0; #endif return 0; @@ -451,28 +448,6 @@ void sunxi_board_init(void) } #endif -#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET) -extern const struct musb_platform_ops sunxi_musb_ops; - -static struct musb_hdrc_config musb_config = { - .multipoint = 1, - .dyn_fifo = 1, - .num_eps = 6, - .ram_bits = 11, -}; - -static struct musb_hdrc_platform_data musb_plat = { -#if defined(CONFIG_MUSB_HOST) - .mode = MUSB_HOST, -#else - .mode = MUSB_PERIPHERAL, -#endif - .config = &musb_config, - .power = 250, - .platform_ops = &sunxi_musb_ops, -}; -#endif - #ifdef CONFIG_USB_GADGET int g_dnl_board_usb_cable_connected(void) { @@ -535,9 +510,8 @@ int misc_init_r(void) if (ret) return ret; #endif -#if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET) - musb_register(&musb_plat, NULL, (void *)SUNXI_USB0_BASE); -#endif + sunxi_musb_board_init(); + return 0; } #endif |