diff options
Diffstat (limited to 'board/ti/omap5_uevm/evm.c')
| -rw-r--r-- | board/ti/omap5_uevm/evm.c | 78 |
1 files changed, 10 insertions, 68 deletions
diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c index e35f319b46..319bb6aa64 100644 --- a/board/ti/omap5_uevm/evm.c +++ b/board/ti/omap5_uevm/evm.c @@ -12,6 +12,7 @@ #include <asm/arch/omap.h> #include <asm/arch/sys_proto.h> #include <asm/arch/mmc_host_def.h> +#include <serial.h> #include <tca642x.h> #include <usb.h> #include <linux/delay.h> @@ -149,39 +150,21 @@ int board_init(void) return 0; } -int board_eth_init(bd_t *bis) +#if defined(CONFIG_SPL_OS_BOOT) +int spl_start_uboot(void) { + /* break into full u-boot on 'c' */ + if (serial_tstc() && serial_getc() == 'c') + return 1; + return 0; } +#endif /* CONFIG_SPL_OS_BOOT */ -#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP) -static void enable_host_clocks(void) +int board_eth_init(bd_t *bis) { - int auxclk; - int hs_clk_ctrl_val = (OPTFCLKEN_HSIC60M_P3_CLK | - OPTFCLKEN_HSIC480M_P3_CLK | - OPTFCLKEN_HSIC60M_P2_CLK | - OPTFCLKEN_HSIC480M_P2_CLK | - OPTFCLKEN_UTMI_P3_CLK | OPTFCLKEN_UTMI_P2_CLK); - - /* Enable port 2 and 3 clocks*/ - setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, hs_clk_ctrl_val); - - /* Enable port 2 and 3 usb host ports tll clocks*/ - setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, - (OPTFCLKEN_USB_CH1_CLK_ENABLE | OPTFCLKEN_USB_CH2_CLK_ENABLE)); -#ifdef CONFIG_USB_XHCI_OMAP - /* Enable the USB OTG Super speed clocks */ - setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl, - (OPTFCLKEN_REFCLK960M | OTG_SS_CLKCTRL_MODULEMODE_HW)); -#endif - - auxclk = readl((*prcm)->scrm_auxclk1); - /* Request auxilary clock */ - auxclk |= AUXCLK_ENABLE_MASK; - writel(auxclk, (*prcm)->scrm_auxclk1); + return 0; } -#endif /** * @brief misc_init_r - Configure EVM board specific configurations @@ -223,45 +206,6 @@ int board_mmc_init(bd_t *bis) } #endif -#ifdef CONFIG_USB_EHCI_HCD -static struct omap_usbhs_board_data usbhs_bdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC, - .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC, -}; - -int ehci_hcd_init(int index, enum usb_init_type init, - struct ehci_hccr **hccr, struct ehci_hcor **hcor) -{ - int ret; - - enable_host_clocks(); - - ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor); - if (ret < 0) { - puts("Failed to initialize ehci\n"); - return ret; - } - - return 0; -} - -int ehci_hcd_stop(void) -{ - return omap_ehci_hcd_stop(); -} - -void usb_hub_reset_devices(struct usb_hub_device *hub, int port) -{ - /* The LAN9730 needs to be reset after the port power has been set. */ - if (port == 3) { - gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 0); - udelay(10); - gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 1); - } -} -#endif - #ifdef CONFIG_USB_XHCI_OMAP /** * @brief board_usb_init - Configure EVM board specific configurations @@ -276,8 +220,6 @@ int board_usb_init(int index, enum usb_init_type init) ret = palmas_enable_ss_ldo(); #endif - enable_host_clocks(); - return 0; } #endif |