17 files changed, 305 insertions, 285 deletions

diff --git a/board/dhelectronics/dh_imx6/dh_imx6.c b/board/dhelectronics/dh_imx6/dh_imx6.c
index 33ce7e8ff1..b6f8b11a10 100644
--- a/board/dhelectronics/dh_imx6/dh_imx6.c
+++ b/board/dhelectronics/dh_imx6/dh_imx6.c
@@ -28,10 +28,7 @@
 #include <fsl_esdhc_imx.h>
 #include <fuse.h>
 #include <i2c_eeprom.h>
-#include <miiphy.h>
 #include <mmc.h>
-#include <net.h>
-#include <netdev.h>
 #include <usb.h>
 #include <usb/ehci-ci.h>
 
@@ -52,24 +49,6 @@ int overwrite_console(void)
 	return 1;
 }
 
-#ifdef CONFIG_FEC_MXC
-static void eth_phy_reset(void)
-{
-	/* Reset PHY */
-	gpio_direction_output(IMX_GPIO_NR(5, 0) , 0);
-	udelay(500);
-	gpio_set_value(IMX_GPIO_NR(5, 0), 1);
-
-	/* Enable VIO */
-	gpio_direction_output(IMX_GPIO_NR(1, 7) , 0);
-
-	/*
-	 * KSZ9021 PHY needs at least 10 mSec after PHY reset
-	 * is released to stabilize
-	 */
-	mdelay(10);
-}
-
 static int setup_fec_clock(void)
 {
 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
@@ -80,34 +59,6 @@ static int setup_fec_clock(void)
 	return enable_fec_anatop_clock(0, ENET_50MHZ);
 }
 
-int board_eth_init(bd_t *bis)
-{
-	uint32_t base = IMX_FEC_BASE;
-	struct mii_dev *bus = NULL;
-	struct phy_device *phydev = NULL;
-
-	gpio_request(IMX_GPIO_NR(5, 0), "PHY-reset");
-	gpio_request(IMX_GPIO_NR(1, 7), "VIO");
-
-	setup_fec_clock();
-
-	eth_phy_reset();
-
-	bus = fec_get_miibus(base, -1);
-	if (!bus)
-		return -EINVAL;
-
-	/* Scan PHY 0 */
-	phydev = phy_find_by_mask(bus, 0xf, PHY_INTERFACE_MODE_RGMII);
-	if (!phydev) {
-		printf("Ethernet PHY not found!\n");
-		return -EINVAL;
-	}
-
-	return fec_probe(bis, -1, base, bus, phydev);
-}
-#endif
-
 #ifdef CONFIG_USB_EHCI_MX6
 static void setup_usb(void)
 {
@@ -190,6 +141,8 @@ int board_init(void)
 
 	setup_dhcom_mac_from_fuse();
 
+	setup_fec_clock();
+
 	return 0;
 }
 
diff --git a/board/freescale/imx8mm_evk/imx8mm_evk.c b/board/freescale/imx8mm_evk/imx8mm_evk.c
index c5fd940eeb..53ebb949df 100644
--- a/board/freescale/imx8mm_evk/imx8mm_evk.c
+++ b/board/freescale/imx8mm_evk/imx8mm_evk.c
@@ -15,7 +15,11 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = PHYS_SDRAM_SIZE;
+	/* rom_pointer[1] contains the size of TEE occupies */
+	if (rom_pointer[1])
+		gd->ram_size = PHYS_SDRAM_SIZE - rom_pointer[1];
+	else
+		gd->ram_size = PHYS_SDRAM_SIZE;
 
 	return 0;
 }
diff --git a/board/freescale/imx8qxp_mek/spl.c b/board/freescale/imx8qxp_mek/spl.c
index cb4006eb2a..e4e4cbe716 100644
--- a/board/freescale/imx8qxp_mek/spl.c
+++ b/board/freescale/imx8qxp_mek/spl.c
@@ -12,9 +12,24 @@
 #include <dm/uclass-internal.h>
 #include <dm/device-internal.h>
 #include <dm/lists.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define GPIO_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			 (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			 (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			 (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define USDHC2_SD_PWR IMX_GPIO_NR(4, 19)
+static iomux_cfg_t usdhc2_sd_pwr[] = {
+	SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+};
+
 void spl_board_init(void)
 {
 	struct udevice *dev;
@@ -32,6 +47,9 @@ void spl_board_init(void)
 
 	timer_init();
 
+	imx8_iomux_setup_multiple_pads(usdhc2_sd_pwr, ARRAY_SIZE(usdhc2_sd_pwr));
+	gpio_direction_output(USDHC2_SD_PWR, 0);
+
 	preloader_console_init();
 
 	puts("Normal Boot\n");
diff --git a/board/freescale/imxrt1020-evk/Kconfig b/board/freescale/imxrt1020-evk/Kconfig
new file mode 100644
index 0000000000..d00cbff094
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/Kconfig
@@ -0,0 +1,22 @@
+if TARGET_IMXRT1020_EVK
+
+config SYS_BOARD
+	string
+	default "imxrt1020-evk"
+
+config SYS_VENDOR
+	string
+	default "freescale"
+
+config SYS_SOC
+	string
+	default "imxrt1020"
+
+config SYS_CONFIG_NAME
+	string
+	default "imxrt1020-evk"
+
+config IMX_CONFIG
+	default "board/freescale/imxrt1020-evk/imximage.cfg"
+
+endif
diff --git a/board/freescale/imxrt1020-evk/MAINTAINERS b/board/freescale/imxrt1020-evk/MAINTAINERS
new file mode 100644
index 0000000000..05f017b2ba
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/MAINTAINERS
@@ -0,0 +1,6 @@
+IMXRT1020 EVALUATION KIT
+M:	Giulio Benetti <giulio.benetti@benettiengineering.com>
+S:	Maintained
+F:	board/freescale/imxrt1020-evk
+F:	include/configs/imxrt1020-evk.h
+F:	configs/imxrt1020-evk_defconfig
diff --git a/board/freescale/imxrt1020-evk/Makefile b/board/freescale/imxrt1020-evk/Makefile
new file mode 100644
index 0000000000..807dc7c35e
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2020
+# Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+
+obj-y	:= imxrt1020-evk.o
diff --git a/board/freescale/imxrt1020-evk/README b/board/freescale/imxrt1020-evk/README
new file mode 100644
index 0000000000..3da72fdad2
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/README
@@ -0,0 +1,31 @@
+How to use U-Boot on NXP i.MXRT1020 EVK
+-----------------------------------------------
+
+- Build U-Boot for i.MXRT1020 EVK:
+
+$ make mrproper
+$ make imxrt1020-evk_defconfig
+$ make
+
+This will generate the SPL image called SPL and the u-boot.img.
+
+- Flash the SPL image into the micro SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot.img image into the micro SD card:
+
+sudo dd if=u-boot.img of=/dev/sdb bs=1k seek=128; sync
+
+- Jumper settings:
+
+SW8: 0 1 1 0
+
+where 0 means bottom position and 1 means top position (from the
+switch label numbers reference).
+
+- Connect the USB cable between the EVK and the PC for the console.
+(The USB console connector is the one close the ethernet connector)
+
+- Insert the micro SD card in the board, power it up and U-Boot messages should
+come up.
diff --git a/board/freescale/imxrt1020-evk/imximage.cfg b/board/freescale/imxrt1020-evk/imximage.cfg
new file mode 100644
index 0000000000..9bcc2c1590
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/imximage.cfg
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2020
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+/* Set all FlexRAM as OCRAM(01b) */
+DATA 4 0x400AC044 0x00005555
+/* Use FLEXRAM_BANK_CFG to config FlexRAM */
+SET_BIT 4 0x400AC040 0x4
diff --git a/board/freescale/imxrt1020-evk/imxrt1020-evk.c b/board/freescale/imxrt1020-evk/imxrt1020-evk.c
new file mode 100644
index 0000000000..06ad524d5d
--- /dev/null
+++ b/board/freescale/imxrt1020-evk/imxrt1020-evk.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <ram.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/armv7m.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+#ifndef CONFIG_SUPPORT_SPL
+	int rv;
+	struct udevice *dev;
+
+	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
+	if (rv) {
+		debug("DRAM init failed: %d\n", rv);
+		return rv;
+	}
+
+#endif
+	return fdtdec_setup_mem_size_base();
+}
+
+int dram_init_banksize(void)
+{
+	return fdtdec_setup_memory_banksize();
+}
+
+#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	debug("SPL: booting kernel\n");
+	/* break into full u-boot on 'c' */
+	return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+int spl_dram_init(void)
+{
+	struct udevice *dev;
+	int rv;
+
+	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
+	if (rv)
+		debug("DRAM init failed: %d\n", rv);
+	return rv;
+}
+
+void spl_board_init(void)
+{
+	spl_dram_init();
+	preloader_console_init();
+	arch_cpu_init(); /* to configure mpu for sdram rw permissions */
+}
+
+u32 spl_boot_device(void)
+{
+	return BOOT_DEVICE_MMC1;
+}
+#endif
+
+u32 get_board_rev(void)
+{
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
+
+	return 0;
+}
diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
index 9cb5b14f13..07941fb156 100644
--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
@@ -196,56 +196,6 @@ int board_ehci_hcd_init(int port)
 #endif
 
 #ifdef CONFIG_FEC_MXC
-/*
- * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
- * be used for ENET1 or ENET2, cannot be used for both.
- */
-static iomux_v3_cfg_t const fec1_pads[] = {
-	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
-	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
-	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const fec2_pads[] = {
-	MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
-	MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
-
-	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
-	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-
-	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static void setup_iomux_fec(int fec_id)
-{
-	if (fec_id == 0)
-		imx_iomux_v3_setup_multiple_pads(fec1_pads,
-						 ARRAY_SIZE(fec1_pads));
-	else
-		imx_iomux_v3_setup_multiple_pads(fec2_pads,
-						 ARRAY_SIZE(fec2_pads));
-}
-
-int board_eth_init(bd_t *bis)
-{
-	setup_iomux_fec(CONFIG_FEC_ENET_DEV);
-
-	return fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
-				       CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
-}
-
 static int setup_fec(int fec_id)
 {
 	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
diff --git a/board/freescale/mx6ullevk/mx6ullevk.c b/board/freescale/mx6ullevk/mx6ullevk.c
index e1eddbff95..3f1ecce10f 100644
--- a/board/freescale/mx6ullevk/mx6ullevk.c
+++ b/board/freescale/mx6ullevk/mx6ullevk.c
@@ -19,6 +19,7 @@
 #include <fsl_esdhc_imx.h>
 #include <linux/sizes.h>
 #include <mmc.h>
+#include <miiphy.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -60,11 +61,57 @@ int board_early_init_f(void)
 	return 0;
 }
 
+#ifdef CONFIG_FEC_MXC
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	if (fec_id == 0) {
+		/*
+		 * Use 50MHz anatop loopback REF_CLK1 for ENET1,
+		 * clear gpr1[13], set gpr1[17].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+				IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+	} else {
+		/*
+		 * Use 50MHz anatop loopback REF_CLK2 for ENET2,
+		 * clear gpr1[14], set gpr1[18].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+				IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+	}
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
 int board_init(void)
 {
 	/* Address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+#ifdef	CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
 	return 0;
 }
 
diff --git a/board/k+p/kp_imx53/kp_imx53.c b/board/k+p/kp_imx53/kp_imx53.c
index 2f57310e27..eb5b67d1e6 100644
--- a/board/k+p/kp_imx53/kp_imx53.c
+++ b/board/k+p/kp_imx53/kp_imx53.c
@@ -48,7 +48,7 @@ static int power_init(void)
 	struct udevice *dev;
 	int ret;
 
-	ret = pmic_get("mc34708", &dev);
+	ret = pmic_get("mc34708@8", &dev);
 	if (ret) {
 		printf("%s: mc34708 not found !\n", __func__);
 		return ret;
diff --git a/board/toradex/verdin-imx8mm/verdin-imx8mm.c b/board/toradex/verdin-imx8mm/verdin-imx8mm.c
index 16b9fa1ec1..cb9b4e3b0a 100644
--- a/board/toradex/verdin-imx8mm/verdin-imx8mm.c
+++ b/board/toradex/verdin-imx8mm/verdin-imx8mm.c
@@ -5,6 +5,7 @@
 
 #include <common.h>
 #include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
 #include <asm/io.h>
 #include <miiphy.h>
 #include <netdev.h>
@@ -13,7 +14,11 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+	/* rom_pointer[1] contains the size of TEE occupies */
+	if (rom_pointer[1])
+		gd->ram_size = PHYS_SDRAM_SIZE - rom_pointer[1];
+	else
+		gd->ram_size = PHYS_SDRAM_SIZE;
 
 	return 0;
 }
diff --git a/board/tqc/tqma6/Kconfig b/board/tqc/tqma6/Kconfig
index 6df4134286..084fdb5230 100644
--- a/board/tqc/tqma6/Kconfig
+++ b/board/tqc/tqma6/Kconfig
@@ -63,6 +63,17 @@ choice
 
 config MBA6
 	bool "TQMa6 on MBa6 Starterkit"
+	select DM_ETH
+	select USB
+	select DM_USB
+	select CMD_USB
+	select USB_STORAGE
+	select USB_HOST_ETHER
+	select USB_ETHER_SMSC95XX
+	select PHYLIB
+	select PHY_MICREL
+	select PHY_MICREL_KSZ90X1
+	select MXC_UART
 	help
 	  Select the MBa6 starterkit. This features a GigE Phy, USB, SD-Card
 	  etc.
@@ -74,6 +85,10 @@ config WRU4
 
 endchoice
 
+config SYS_TEXT_BASE
+	default 0x2fc00000 if TQMA6S
+	default 0x4fc00000 if TQMA6Q || TQMA6DL
+
 config IMX_CONFIG
 	default "board/tqc/tqma6/tqma6q.cfg" if TQMA6Q
 	default "board/tqc/tqma6/tqma6dl.cfg" if TQMA6DL
diff --git a/board/tqc/tqma6/tqma6.c b/board/tqc/tqma6/tqma6.c
index c8ddc2c1f8..675341abdd 100644
--- a/board/tqc/tqma6/tqma6.c
+++ b/board/tqc/tqma6/tqma6.c
@@ -60,6 +60,7 @@ int dram_init(void)
 
 static const uint16_t tqma6_emmc_dsr = 0x0100;
 
+#ifndef CONFIG_DM_MMC
 /* eMMC on USDHCI3 always present */
 static iomux_v3_cfg_t const tqma6_usdhc3_pads[] = {
 	NEW_PAD_CTRL(MX6_PAD_SD3_CLK__SD3_CLK,		USDHC_PAD_CTRL),
@@ -132,7 +133,9 @@ int board_mmc_init(bd_t *bis)
 
 	return 0;
 }
+#endif
 
+#ifndef CONFIG_DM_SPI
 static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = {
 	/* SS1 */
 	NEW_PAD_CTRL(MX6_PAD_EIM_D19__GPIO3_IO19, SPI_PAD_CTRL),
@@ -164,7 +167,9 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
 		(cs == CONFIG_SF_DEFAULT_CS)) ? TQMA6_SF_CS_GPIO : -1;
 }
 #endif
+#endif
 
+#ifdef CONFIG_SYS_I2C
 static struct i2c_pads_info tqma6_i2c3_pads = {
 	/* I2C3: on board LM75, M24C64,  */
 	.scl = {
@@ -194,6 +199,7 @@ static void tqma6_setup_i2c(void)
 	if (ret)
 		printf("setup I2C3 failed: %d\n", ret);
 }
+#endif
 
 int board_early_init_f(void)
 {
@@ -205,8 +211,12 @@ int board_init(void)
 	/* address of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 
+#ifndef CONFIG_DM_SPI
 	tqma6_iomuxc_spi();
+#endif
+#ifdef CONFIG_SYS_I2C
 	tqma6_setup_i2c();
+#endif
 
 	tqma6_bb_board_init();
 
@@ -235,6 +245,7 @@ static const char *tqma6_get_boardname(void)
 	};
 }
 
+#ifdef CONFIG_POWER
 /* setup board specific PMIC */
 int power_init_board(void)
 {
@@ -251,6 +262,7 @@ int power_init_board(void)
 
 	return 0;
 }
+#endif
 
 int board_late_init(void)
 {
diff --git a/board/tqc/tqma6/tqma6_mba6.c b/board/tqc/tqma6/tqma6_mba6.c
index 154ea0e925..a5b7587737 100644
--- a/board/tqc/tqma6/tqma6_mba6.c
+++ b/board/tqc/tqma6/tqma6_mba6.c
@@ -68,13 +68,6 @@
 
 #endif
 
-#define ENET_RX_PAD_CTRL	(PAD_CTL_DSE_34ohm)
-#define ENET_TX_PAD_CTRL	(PAD_CTL_PUS_100K_UP | PAD_CTL_DSE_34ohm)
-#define ENET_CLK_PAD_CTRL	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_HIGH | \
-				 PAD_CTL_DSE_34ohm)
-#define ENET_MDIO_PAD_CTRL	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
-				 PAD_CTL_DSE_60ohm)
-
 /* disable on die termination for RGMII */
 #define IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM_DISABLE	0x00000000
 /* optimised drive strength for 1.0 .. 1.3 V signal on RGMII */
@@ -82,34 +75,6 @@
 /* optimised drive strength for 1.3 .. 2.5 V signal on RGMII */
 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V	0x000C0000
 
-#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 25)
-
-static iomux_v3_cfg_t const mba6_enet_pads[] = {
-	NEW_PAD_CTRL(MX6_PAD_ENET_MDIO__ENET_MDIO,	ENET_MDIO_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_ENET_MDC__ENET_MDC,	ENET_MDIO_PAD_CTRL),
-
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TXC__RGMII_TXC,	ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TD0__RGMII_TD0,	ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TD1__RGMII_TD1,	ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TD2__RGMII_TD2,	ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TD3__RGMII_TD3,	ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL,
-		     ENET_TX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_ENET_REF_CLK__ENET_TX_CLK,	ENET_CLK_PAD_CTRL),
-	/*
-	 * these pins are also used for config strapping by phy
-	 */
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RD0__RGMII_RD0,	ENET_RX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RD1__RGMII_RD1,	ENET_RX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RD2__RGMII_RD2,	ENET_RX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RD3__RGMII_RD3,	ENET_RX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RXC__RGMII_RXC,	ENET_RX_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL,
-		     ENET_RX_PAD_CTRL),
-	/* KSZ9031 PHY Reset */
-	NEW_PAD_CTRL(MX6_PAD_ENET_CRS_DV__GPIO1_IO25,	GPIO_OUT_PAD_CTRL),
-};
-
 static void mba6_setup_iomuxc_enet(void)
 {
 	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
@@ -121,22 +86,6 @@ static void mba6_setup_iomuxc_enet(void)
 		     (void *)IOMUX_SW_PAD_CTRL_GRP_RGMII_TERM);
 	__raw_writel(IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII_1P5V,
 		     (void *)IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII);
-
-	imx_iomux_v3_setup_multiple_pads(mba6_enet_pads,
-					 ARRAY_SIZE(mba6_enet_pads));
-
-	/* Reset PHY */
-	gpio_direction_output(ENET_PHY_RESET_GPIO , 0);
-	/* Need delay 10ms after power on according to KSZ9031 spec */
-	mdelay(10);
-	gpio_set_value(ENET_PHY_RESET_GPIO, 1);
-	/*
-	 * KSZ9031 manual: 100 usec wait time after reset before communication
-	 * over MDIO
-	 * BUGBUG: hardware has an RC const that needs > 10 msec from 0->1 on
-	 * reset before the phy sees a high level
-	 */
-	mdelay(15);
 }
 
 static iomux_v3_cfg_t const mba6_uart2_pads[] = {
@@ -150,91 +99,14 @@ static void mba6_setup_iomuxc_uart(void)
 					 ARRAY_SIZE(mba6_uart2_pads));
 }
 
-#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
-#define USDHC2_WP_GPIO	IMX_GPIO_NR(1, 2)
-
-int tqma6_bb_board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret = 0;
-
-	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
-		ret = !gpio_get_value(USDHC2_CD_GPIO);
-
-	return ret;
-}
-
-int tqma6_bb_board_mmc_getwp(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret = 0;
-
-	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
-		ret = gpio_get_value(USDHC2_WP_GPIO);
-
-	return ret;
-}
-
-static struct fsl_esdhc_cfg mba6_usdhc_cfg = {
-	.esdhc_base = USDHC2_BASE_ADDR,
-	.max_bus_width = 4,
-};
-
-static iomux_v3_cfg_t const mba6_usdhc2_pads[] = {
-	NEW_PAD_CTRL(MX6_PAD_SD2_CLK__SD2_CLK,		USDHC_CLK_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD2_CMD__SD2_CMD,		USDHC_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD2_DAT0__SD2_DATA0,	USDHC_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD2_DAT1__SD2_DATA1,	USDHC_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD2_DAT2__SD2_DATA2,	USDHC_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD2_DAT3__SD2_DATA3,	USDHC_PAD_CTRL),
-	/* CD */
-	NEW_PAD_CTRL(MX6_PAD_GPIO_4__GPIO1_IO04,	GPIO_IN_PAD_CTRL),
-	/* WP */
-	NEW_PAD_CTRL(MX6_PAD_GPIO_2__GPIO1_IO02,	GPIO_IN_PAD_CTRL),
-};
-
-int tqma6_bb_board_mmc_init(bd_t *bis)
-{
-	imx_iomux_v3_setup_multiple_pads(mba6_usdhc2_pads,
-					 ARRAY_SIZE(mba6_usdhc2_pads));
-	gpio_direction_input(USDHC2_CD_GPIO);
-	gpio_direction_input(USDHC2_WP_GPIO);
-
-	mba6_usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-	if (fsl_esdhc_initialize(bis, &mba6_usdhc_cfg))
-		puts("Warning: failed to initialize SD\n");
-
-	return 0;
-}
-
-static struct i2c_pads_info mba6_i2c1_pads = {
-/* I2C1: MBa6x */
-	.scl = {
-		.i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__I2C1_SCL,
-					 I2C_PAD_CTRL),
-		.gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT9__GPIO5_IO27,
-					  I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(5, 27)
-	},
-	.sda = {
-		.i2c_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__I2C1_SDA,
-					 I2C_PAD_CTRL),
-		.gpio_mode = NEW_PAD_CTRL(MX6_PAD_CSI0_DAT8__GPIO5_IO26,
-					  I2C_PAD_CTRL),
-		.gp = IMX_GPIO_NR(5, 26)
-	}
-};
-
-static void mba6_setup_i2c(void)
+int board_mmc_get_env_dev(int devno)
 {
-	int ret;
 	/*
-	 * use logical index for bus, e.g. I2C1 -> 0
-	 * warn on error
+	 * This assumes that the baseboard registered
+	 * the boot device first ...
+	 * Note: SDHC3 == idx2
 	 */
-	ret = setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mba6_i2c1_pads);
-	if (ret)
-		printf("setup I2C1 failed: %d\n", ret);
+	return (2 == devno) ? 0 : 1;
 }
 
 int board_phy_config(struct phy_device *phydev)
@@ -284,37 +156,6 @@ int board_phy_config(struct phy_device *phydev)
 	return 0;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	uint32_t base = IMX_FEC_BASE;
-	struct mii_dev *bus = NULL;
-	struct phy_device *phydev = NULL;
-	int ret;
-
-	bus = fec_get_miibus(base, -1);
-	if (!bus)
-		return -EINVAL;
-	/* scan phy */
-	phydev = phy_find_by_mask(bus, (0xf << CONFIG_FEC_MXC_PHYADDR),
-					PHY_INTERFACE_MODE_RGMII);
-
-	if (!phydev) {
-		ret = -EINVAL;
-		goto free_bus;
-	}
-	ret  = fec_probe(bis, -1, base, bus, phydev);
-	if (ret)
-		goto free_phydev;
-
-	return 0;
-
-free_phydev:
-	free(phydev);
-free_bus:
-	free(bus);
-	return ret;
-}
-
 int tqma6_bb_board_early_init_f(void)
 {
 	mba6_setup_iomuxc_uart();
@@ -324,8 +165,6 @@ int tqma6_bb_board_early_init_f(void)
 
 int tqma6_bb_board_init(void)
 {
-	mba6_setup_i2c();
-	/* do it here - to have reset completed */
 	mba6_setup_iomuxc_enet();
 
 	return 0;
diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c
index 5725c5816c..fb2f3c1fd2 100644
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -369,7 +369,7 @@ int power_init_board(void)
 
 	reg = pmic_reg_read(dev, PFUZE100_DEVICEID);
 	if (reg < 0) {
-		printf("pmic_reg_read() ret %d\n", reg);
+		debug("pmic_reg_read() ret %d\n", reg);
 		return 0;
 	}
 	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
@@ -404,6 +404,7 @@ static const struct boot_mode board_boot_modes[] = {
 static bool is_revc1(void)
 {
 	SETUP_IOMUX_PADS(rev_detection_pad);
+	gpio_request(REV_DETECTION, "REV_DETECT");
 	gpio_direction_input(REV_DETECTION);
 
 	if (gpio_get_value(REV_DETECTION))
@@ -442,6 +443,14 @@ int board_late_init(void)
 		env_set("board_name", "B1");
 #endif
 	setup_iomux_enet();
+
+	if (is_revd1())
+		puts("Board: Wandboard rev D1\n");
+	else if (is_revc1())
+		puts("Board: Wandboard rev C1\n");
+	else
+		puts("Board: Wandboard rev B1\n");
+
 	return 0;
 }
 
@@ -466,31 +475,17 @@ int board_init(void)
 	return 0;
 }
 
-int checkboard(void)
-{
-	gpio_request(REV_DETECTION, "REV_DETECT");
-
-	if (is_revd1())
-		puts("Board: Wandboard rev D1\n");
-	else if (is_revc1())
-		puts("Board: Wandboard rev C1\n");
-	else
-		puts("Board: Wandboard rev B1\n");
-
-	return 0;
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
 	if (is_mx6dq()) {
-		if (!strcmp(name, "imx6q-wandboard-revb1"))
+		if (!strcmp(name, "imx6q-wandboard-revd1"))
 			return 0;
 	} else if (is_mx6dqp()) {
 		if (!strcmp(name, "imx6qp-wandboard-revd1"))
 			return 0;
 	} else if (is_mx6dl() || is_mx6solo()) {
-		if (!strcmp(name, "imx6dl-wandboard-revb1"))
+		if (!strcmp(name, "imx6dl-wandboard-revd1"))
 			return 0;
 	}