diff options
Diffstat (limited to 'cpu/ixp/npe/include/IxSspAcc.h')
| -rw-r--r-- | cpu/ixp/npe/include/IxSspAcc.h | 1271 |
1 files changed, 1271 insertions, 0 deletions
diff --git a/cpu/ixp/npe/include/IxSspAcc.h b/cpu/ixp/npe/include/IxSspAcc.h new file mode 100644 index 0000000000..35e7abf06f --- /dev/null +++ b/cpu/ixp/npe/include/IxSspAcc.h @@ -0,0 +1,1271 @@ +/** + * @file IxSspAcc.h + * + * @brief Header file for the IXP400 SSP Serial Port Access (IxSspAcc) + * + * @version $Revision: 0.1 $ + * + * @par + * IXP400 SW Release version 2.0 + * + * -- Copyright Notice -- + * + * @par + * Copyright 2001-2005, Intel Corporation. + * All rights reserved. + * + * @par + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the name of the Intel Corporation nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * @par + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + * + * @par + * -- End of Copyright Notice -- + */ + +/** + * @defgroup IxSspAcc IXP400 SSP Serial Port Access (IxSspAcc) API + * + * @brief IXP400 SSP Serial Port Access Public API + * + * @{ + */ +#ifndef IXSSPACC_H +#define IXSSPACC_H + +#ifdef __ixp46X + +#include "IxOsal.h" + +/* + * Section for enum + */ +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccDataSize + * + * @brief The data sizes in bits that are supported by the protocol + */ +typedef enum +{ + DATA_SIZE_TOO_SMALL = 0x2, + DATA_SIZE_4 = 0x3, + DATA_SIZE_5, + DATA_SIZE_6, + DATA_SIZE_7, + DATA_SIZE_8, + DATA_SIZE_9, + DATA_SIZE_10, + DATA_SIZE_11, + DATA_SIZE_12, + DATA_SIZE_13, + DATA_SIZE_14, + DATA_SIZE_15, + DATA_SIZE_16, + DATA_SIZE_TOO_BIG +} IxSspAccDataSize; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccPortStatus + * + * @brief The status of the SSP port to be set to enable/disable + */ +typedef enum +{ + SSP_PORT_DISABLE = 0x0, + SSP_PORT_ENABLE, + INVALID_SSP_PORT_STATUS +} IxSspAccPortStatus; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccFrameFormat + * + * @brief The frame format that is to be used - SPI, SSP, or Microwire + */ +typedef enum +{ + SPI_FORMAT = 0x0, + SSP_FORMAT, + MICROWIRE_FORMAT, + INVALID_FORMAT +} IxSspAccFrameFormat; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccClkSource + * + * @brief The source to produce the SSP serial clock + */ +typedef enum +{ + ON_CHIP_CLK = 0x0, + EXTERNAL_CLK, + INVALID_CLK_SOURCE +} IxSspAccClkSource; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccSpiSclkPhase + * + * @brief The SPI SCLK Phase: + * 0 - SCLK is inactive one cycle at the start of a frame and 1/2 cycle at the + * end of a frame. + * 1 - SCLK is inactive 1/2 cycle at the start of a frame and one cycle at the + * end of a frame. + */ +typedef enum +{ + START_ONE_END_HALF = 0x0, + START_HALF_END_ONE, + INVALID_SPI_PHASE +} IxSspAccSpiSclkPhase; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccSpiSclkPolarity + * + * @brief The SPI SCLK Polarity can be set to either low or high. + */ +typedef enum +{ + SPI_POLARITY_LOW = 0x0, + SPI_POLARITY_HIGH, + INVALID_SPI_POLARITY +} IxSspAccSpiSclkPolarity; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccMicrowireCtlWord + * + * @brief The Microwire control word can be either 8 or 16 bit. + */ +typedef enum +{ + MICROWIRE_8_BIT = 0x0, + MICROWIRE_16_BIT, + INVALID_MICROWIRE_CTL_WORD +} IxSspAccMicrowireCtlWord; + +/** + * @ingroup IxSspAcc + * + * @enum IxSspAccFifoThreshold + * + * @brief The threshold in frames (each frame is defined by IxSspAccDataSize) + * that can be set for the FIFO to trigger a threshold exceed when + * checking with the ExceedThresholdCheck functions or an interrupt + * when it is enabled. + */ +typedef enum +{ + FIFO_TSHLD_1 = 0x0, + FIFO_TSHLD_2, + FIFO_TSHLD_3, + FIFO_TSHLD_4, + FIFO_TSHLD_5, + FIFO_TSHLD_6, + FIFO_TSHLD_7, + FIFO_TSHLD_8, + FIFO_TSHLD_9, + FIFO_TSHLD_10, + FIFO_TSHLD_11, + FIFO_TSHLD_12, + FIFO_TSHLD_13, + FIFO_TSHLD_14, + FIFO_TSHLD_15, + FIFO_TSHLD_16, + INVALID_FIFO_TSHLD +} IxSspAccFifoThreshold; + +/** + * @ingroup IxSspAcc + * + * @enum IX_SSP_STATUS + * + * @brief The statuses that can be returned in a SSP Serial Port Access + */ +typedef enum +{ + IX_SSP_SUCCESS = IX_SUCCESS, /**< Success status */ + IX_SSP_FAIL, /**< Fail status */ + IX_SSP_RX_FIFO_OVERRUN_HANDLER_MISSING, /**< + Rx FIFO Overrun handler is NULL. */ + IX_SSP_RX_FIFO_HANDLER_MISSING, /**< + Rx FIFO threshold hit or above handler is NULL + */ + IX_SSP_TX_FIFO_HANDLER_MISSING, /**< + Tx FIFO threshold hit or below handler is NULL + */ + IX_SSP_FIFO_NOT_EMPTY_FOR_SETTING_CTL_CMD, /**< + Tx FIFO not empty and therefore microwire + control command size setting is not allowed. */ + IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE, /**< + frame format selected is invalid. */ + IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE, /**< + data size selected is invalid. */ + IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE, /**< + source clock selected is invalid. */ + IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE, /**< + Tx FIFO threshold selected is invalid. */ + IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE, /**< + Rx FIFO threshold selected is invalid. */ + IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE, /**< + SPI phase selected is invalid. */ + IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE, /**< + SPI polarity selected is invalid. */ + IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE, /**< + Microwire control command selected is invalid + */ + IX_SSP_INT_UNBIND_FAIL, /**< Interrupt unbind fail to unbind SSP + interrupt */ + IX_SSP_INT_BIND_FAIL, /**< Interrupt bind fail during init */ + IX_SSP_RX_FIFO_NOT_EMPTY, /**< + Rx FIFO not empty while trying to change data + size. */ + IX_SSP_TX_FIFO_NOT_EMPTY, /**< + Rx FIFO not empty while trying to change data + size or microwire control command size. */ + IX_SSP_POLL_MODE_BLOCKING, /**< + poll mode selected blocks interrupt mode from + being selected. */ + IX_SSP_TX_FIFO_HIT_BELOW_THRESHOLD, /**< + Tx FIFO level hit or below threshold. */ + IX_SSP_TX_FIFO_EXCEED_THRESHOLD, /**< + Tx FIFO level exceeded threshold. */ + IX_SSP_RX_FIFO_HIT_ABOVE_THRESHOLD, /**< + Rx FIFO level hit or exceeded threshold. */ + IX_SSP_RX_FIFO_BELOW_THRESHOLD, /**< + Rx FIFO level below threshold. */ + IX_SSP_BUSY, /**< SSP is busy. */ + IX_SSP_IDLE, /**< SSP is idle. */ + IX_SSP_OVERRUN_OCCURRED, /**< + SSP has experienced an overrun. */ + IX_SSP_NO_OVERRUN, /**< + SSP did not experience an overrun. */ + IX_SSP_NOT_SUPORTED, /**< hardware does not support SSP */ + IX_SSP_NOT_INIT, /**< SSP Access not intialized */ + IX_SSP_NULL_POINTER /**< parameter passed in is NULL */ +} IX_SSP_STATUS; + +/** + * @ingroup IxSspAcc + * + * @brief SSP Rx FIFO Overrun handler + * + * This function is called for the client to handle Rx FIFO Overrun that occurs + * in the SSP hardware + */ +typedef void (*RxFIFOOverrunHandler)(void); + +/** + * @ingroup IxSspAcc + * + * @brief SSP Rx FIFO Threshold hit or above handler + * + * This function is called for the client to handle Rx FIFO threshold hit or + * or above that occurs in the SSP hardware + */ +typedef void (*RxFIFOThresholdHandler)(void); + +/** + * @ingroup IxSspAcc + * + * @brief SSP Tx FIFO Threshold hit or below handler + * + * This function is called for the client to handle Tx FIFO threshold hit or + * or below that occurs in the SSP hardware + */ +typedef void (*TxFIFOThresholdHandler)(void); + + +/* + * Section for struct + */ +/** + * @ingroup IxSspAcc + * + * @brief contains all the variables required to initialize the SSP serial port + * hardware. + * + * Structure to be filled and used for calling initialization + */ +typedef struct +{ + IxSspAccFrameFormat FrameFormatSelected;/**<Select between SPI, SSP and + Microwire. */ + IxSspAccDataSize DataSizeSelected; /**<Select between 4 and 16. */ + IxSspAccClkSource ClkSourceSelected; /**<Select clock source to be + on-chip or external. */ + IxSspAccFifoThreshold TxFIFOThresholdSelected; + /**<Select Tx FIFO threshold + between 1 to 16. */ + IxSspAccFifoThreshold RxFIFOThresholdSelected; + /**<Select Rx FIFO threshold + between 1 to 16. */ + BOOL RxFIFOIntrEnable; /**<Enable/disable Rx FIFO + threshold interrupt. Disabling + this interrupt will require + the use of the polling function + RxFIFOExceedThresholdCheck. */ + BOOL TxFIFOIntrEnable; /**<Enable/disable Tx FIFO + threshold interrupt. Disabling + this interrupt will require + the use of the polling function + TxFIFOExceedThresholdCheck. */ + RxFIFOThresholdHandler RxFIFOThsldHdlr; /**<Pointer to function to handle + a Rx FIFO interrupt. */ + TxFIFOThresholdHandler TxFIFOThsldHdlr; /**<Pointer to function to handle + a Tx FIFO interrupt. */ + RxFIFOOverrunHandler RxFIFOOverrunHdlr; /**<Pointer to function to handle + a Rx FIFO overrun interrupt. */ + BOOL LoopbackEnable; /**<Select operation mode to be + normal or loopback mode. */ + IxSspAccSpiSclkPhase SpiSclkPhaseSelected; + /**<Select SPI SCLK phase to start + with one inactive cycle and end + with 1/2 inactive cycle or + start with 1/2 inactive cycle + and end with one inactive + cycle. (Only used in + SPI format). */ + IxSspAccSpiSclkPolarity SpiSclkPolaritySelected; + /**<Select SPI SCLK idle state + to be low or high. (Only used in + SPI format). */ + IxSspAccMicrowireCtlWord MicrowireCtlWordSelected; + /**<Select Microwire control + format to be 8 or 16-bit. (Only + used in Microwire format). */ + UINT8 SerialClkRateSelected; /**<Select between 0 (1.8432Mbps) + and 255 (7.2Kbps). The + formula used is Bit rate = + 3.6864x10^6 / + (2 x (SerialClkRateSelect + 1)) + */ +} IxSspInitVars; + +/** + * @ingroup IxSspAcc + * + * @brief contains counters of the SSP statistics + * + * Structure contains all values of counters and associated overflows. + */ +typedef struct +{ + UINT32 ixSspRcvCounter; /**<Total frames received. */ + UINT32 ixSspXmitCounter; /**<Total frames transmitted. */ + UINT32 ixSspOverflowCounter;/**<Total occurrences of overflow. */ +} IxSspAccStatsCounters; + + +/* + * Section for prototypes interface functions + */ + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccInit ( + IxSspInitVars *initVarsSelected); + * + * @brief Initializes the SSP Access module. + * + * @param "IxSspAccInitVars [in] *initVarsSelected" - struct containing required + * variables for initialization + * + * Global Data : + * - None. + * + * This API will initialize the SSP Serial Port hardware to the user specified + * configuration. Then it will enable the SSP Serial Port. + * *NOTE*: Once interrupt or polling mode is selected, the mode cannot be + * changed via the interrupt enable/disable function but the init needs to be + * called again to change it. + * + * @return + * - IX_SSP_SUCCESS - Successfully initialize and enable the SSP + * serial port. + * - IX_SSP_RX_FIFO_HANDLER_MISSING - interrupt mode is selected but RX FIFO + * handler pointer is NULL + * - IX_SSP_TX_FIFO_HANDLER_MISSING - interrupt mode is selected but TX FIFO + * handler pointer is NULL + * - IX_SSP_RX_FIFO_OVERRUN_HANDLER_MISSING - interrupt mode is selected but + * RX FIFO Overrun handler pointer is NULL + * - IX_SSP_RX_FIFO_NOT_EMPTY - Rx FIFO not empty, data size change is not + * allowed. + * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not + * allowed. + * - IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE - frame format selected is invalid + * - IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE - data size selected is invalid + * - IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE - clock source selected is invalid + * - IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE - Tx FIFO threshold level + * selected is invalid + * - IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE - Rx FIFO threshold level + * selected is invalid + * - IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE - SPI phase selected is invalid + * - IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE - SPI polarity selected is invalid + * - IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE - microwire control command + * size is invalid + * - IX_SSP_INT_UNBIND_FAIL - interrupt handler failed to unbind SSP interrupt + * - IX_SSP_INT_BIND_FAIL - interrupt handler failed to bind to SSP interrupt + * hardware trigger + * - IX_SSP_NOT_SUPORTED - hardware does not support SSP + * - IX_SSP_NULL_POINTER - parameter passed in is NULL + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccInit (IxSspInitVars *initVarsSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccUninit ( + void) + * + * @brief Un-initializes the SSP Serial Port Access component + * + * @param - None + * + * Global Data : + * - None. + * + * This API will disable the SSP Serial Port hardware. The client can call the + * init function again if they wish to enable the SSP. + * + * @return + * - IX_SSP_SUCCESS - successfully uninit SSP component + * - IX_SSP_INT_UNBIND_FAIL - interrupt handler failed to unbind SSP interrupt + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccUninit (void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccFIFODataSubmit ( + UINT16 *data, + UINT32 amtOfData) + * + * @brief Inserts data into the SSP Serial Port's FIFO + * + * @param "UINT16 [in] *data" - pointer to the location to transmit the data + * from + * "UINT32 [in] amtOfData" - number of data to be transmitted. + * + * Global Data : + * - None. + * + * This API will insert the amount of data specified by "amtOfData" from buffer + * pointed to by "data" into the FIFO to be transmitted by the hardware. + * + * @return + * - IX_SSP_SUCCESS - Data inserted successfully into FIFO + * - IX_SSP_FAIL - FIFO insufficient space + * - IX_SSP_NULL_POINTER - data pointer passed by client is NULL + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccFIFODataSubmit ( + UINT16* data, + UINT32 amtOfData); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccFIFODataReceive ( + UINT16 *data, + UINT32 amtOfData) + * + * @brief Extract data from the SSP Serial Port's FIFO + * + * @param "UINT16 [in] *data" - pointer to the location to receive the data into + * "UINT32 [in] amtOfData" - number of data to be received. + * + * Global Data : + * - None. + * + * This API will extract the amount of data specified by "amtOfData" from the + * FIFO already received by the hardware into the buffer pointed to by "data". + * + * @return + * - IX_SSP_SUCCESS - Data extracted successfully from FIFO + * - IX_SSP_FAIL - FIFO has no data + * - IX_SSP_NULL_POINTER - data pointer passed by client is NULL + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccFIFODataReceive ( + UINT16* data, + UINT32 amtOfData); + + +/** + * Polling Functions + */ + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccTxFIFOHitOrBelowThresholdCheck ( + void) + * + * @brief Check if the Tx FIFO threshold has been hit or fallen below. + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return whether the Tx FIFO threshold has been exceeded or not + * + * @return + * - IX_SSP_TX_FIFO_HIT_BELOW_THRESHOLD - Tx FIFO level hit or below threshold . + * - IX_SSP_TX_FIFO_EXCEED_THRESHOLD - Tx FIFO level exceeded threshold. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccTxFIFOHitOrBelowThresholdCheck ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOHitOrAboveThresholdCheck ( + void) + * + * @brief Check if the Rx FIFO threshold has been hit or exceeded. + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return whether the Rx FIFO level is below threshold or not + * + * @return + * - IX_SSP_RX_FIFO_HIT_ABOVE_THRESHOLD - Rx FIFO level hit or exceeded threshold + * - IX_SSP_RX_FIFO_BELOW_THRESHOLD - Rx FIFO level below threshold + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccRxFIFOHitOrAboveThresholdCheck ( + void); + + +/** + * Configuration functions + * + * NOTE: These configurations are not required to be called once init is called + * unless configurations need to be changed on the fly. + */ + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccSSPPortStatusSet ( + IxSspAccPortStatus portStatusSelected) + * + * @brief Enables/disables the SSP Serial Port hardware. + * + * @param "IxSspAccPortStatus [in] portStatusSelected" - Set the SSP port to + * enable or disable + * + * Global Data : + * - None. + * + * This API will enable/disable the SSP Serial Port hardware. + * NOTE: This function is called by init to enable the SSP after setting up the + * configurations and by uninit to disable the SSP. + * + * @return + * - IX_SSP_SUCCESS - Port status set with valid enum value + * - IX_SSP_FAIL - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccSSPPortStatusSet ( + IxSspAccPortStatus portStatusSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccFrameFormatSelect ( + IxSspAccFrameFormat frameFormatSelected) + * + * @brief Sets the frame format for the SSP Serial Port hardware + * + * @param "IxSspAccFrameFormat [in] frameFormatSelected" - The frame format of + * SPI, SSP or Microwire can be selected as the format + * + * Global Data : + * - None. + * + * This API will set the format for the transfers via user input. + * *NOTE*: The SSP hardware will be disabled to clear the FIFOs. Then its + * previous state (enabled/disabled) restored after changing the format. + * + * @return + * - IX_SSP_SUCCESS - frame format set with valid enum value + * - IX_SSP_INVALID_FRAME_FORMAT_ENUM_VALUE - invalid frame format value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccFrameFormatSelect ( + IxSspAccFrameFormat frameFormatSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccDataSizeSelect ( + IxSspAccDataSize dataSizeSelected) + * + * @brief Sets the data size for transfers + * + * @param "IxSspAccDataSize [in] dataSizeSelected" - The data size between 4 + * and 16 that can be selected for data transfers + * + * Global Data : + * - None. + * + * This API will set the data size for the transfers via user input. It will + * disallow the change of the data size if either of the Rx/Tx FIFO is not + * empty to prevent data loss. + * *NOTE*: The SSP port will be disabled if the FIFOs are found to be empty and + * if between the check and disabling of the SSP (which clears the + * FIFOs) data is received into the FIFO, it might be lost. + * *NOTE*: The FIFOs can be cleared by disabling the SSP Port if necessary to + * force the data size change. + * + * @return + * - IX_SSP_SUCCESS - data size set with valid enum value + * - IX_SSP_RX_FIFO_NOT_EMPTY - Rx FIFO not empty, data size change is not + * allowed. + * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not + * allowed. + * - IX_SSP_INVALID_DATA_SIZE_ENUM_VALUE - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccDataSizeSelect ( + IxSspAccDataSize dataSizeSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccClockSourceSelect( + IxSspAccClkSource clkSourceSelected) + * + * @brief Sets the clock source of the SSP Serial Port hardware + * + * @param "IxSspAccClkSource [in] clkSourceSelected" - The clock source from + * either external source on on-chip can be selected as the source + * + * Global Data : + * - None. + * + * This API will set the clock source for the transfers via user input. + * + * @return + * - IX_SSP_SUCCESS - clock source set with valid enum value + * - IX_SSP_INVALID_CLOCK_SOURCE_ENUM_VALUE - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccClockSourceSelect ( + IxSspAccClkSource clkSourceSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccSerialClockRateConfigure ( + UINT8 serialClockRateSelected) + * + * @brief Sets the on-chip Serial Clock Rate of the SSP Serial Port hardware. + * + * @param "UINT8 [in] serialClockRateSelected" - The serial clock rate that can + * be set is between 7.2Kbps and 1.8432Mbps. The formula used is + * Bit rate = 3.6864x10^6 / (2 x (SerialClockRateSelected + 1)) + * + * Global Data : + * - None. + * + * This API will set the serial clock rate for the transfers via user input. + * + * @return + * - IX_SSP_SUCCESS - Serial clock rate configured successfully + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccSerialClockRateConfigure ( + UINT8 serialClockRateSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOIntEnable ( + RxFIFOThresholdHandler rxFIFOIntrHandler) + * + * @brief Enables service request interrupt whenever the Rx FIFO hits its + * threshold + * + * @param "void [in] *rxFIFOIntrHandler(UINT32)" - function pointer to the + * interrupt handler for the Rx FIFO exceeded. + * + * Global Data : + * - None. + * + * This API will enable the service request interrupt for the Rx FIFO + * + * @return + * - IX_SSP_SUCCESS - Rx FIFO level interrupt enabled successfully + * - IX_SSP_RX_FIFO_HANDLER_MISSING - missing handler for Rx FIFO level interrupt + * - IX_SSP_POLL_MODE_BLOCKING - poll mode is selected at init, interrupt not + * allowed to be enabled. Use init to enable interrupt mode. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccRxFIFOIntEnable ( + RxFIFOThresholdHandler rxFIFOIntrHandler); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOIntDisable ( + void) + * + * @brief Disables service request interrupt of the Rx FIFO. + * + * @param - None + * + * Global Data : + * - None. + * + * This API will disable the service request interrupt of the Rx FIFO. + * + * @return + * - IX_SSP_SUCCESS - Rx FIFO Interrupt disabled successfully + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccRxFIFOIntDisable ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccTxFIFOIntEnable ( + TxFIFOThresholdHandler txFIFOIntrHandler) + * + * @brief Enables service request interrupt of the Tx FIFO. + * + * @param "void [in] *txFIFOIntrHandler(UINT32)" - function pointer to the + * interrupt handler for the Tx FIFO exceeded. + * + * Global Data : + * - None. + * + * This API will enable the service request interrupt of the Tx FIFO. + * + * @return + * - IX_SSP_SUCCESS - Tx FIFO level interrupt enabled successfully + * - IX_SSP_TX_FIFO_HANDLER_MISSING - missing handler for Tx FIFO level interrupt + * - IX_SSP_POLL_MODE_BLOCKING - poll mode is selected at init, interrupt not + * allowed to be enabled. Use init to enable interrupt mode. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccTxFIFOIntEnable ( + TxFIFOThresholdHandler txFIFOIntrHandler); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccTxFIFOIntDisable ( + void) + * + * @brief Disables service request interrupt of the Tx FIFO + * + * @param - None + * + * Global Data : + * - None. + * + * This API will disable the service request interrupt of the Tx FIFO + * + * @return + * - IX_SSP_SUCCESS - Tx FIFO Interrupt disabled successfuly. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccTxFIFOIntDisable ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccLoopbackEnable ( + BOOL loopbackEnable) + * + * @brief Enables/disables the loopback mode + * + * @param "BOOL [in] loopbackEnable" - True to enable and false to disable. + * + * Global Data : + * - None. + * + * This API will set the mode of operation to either loopback or normal mode + * according to the user input. + * + * @return + * - IX_SSP_SUCCESS - Loopback enabled successfully + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccLoopbackEnable ( + BOOL loopbackEnable); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccSpiSclkPolaritySet ( + IxSspAccSpiSclkPolarity spiSclkPolaritySelected) + * + * @brief Sets the SPI SCLK Polarity to Low or High + * + * @param - "IxSspAccSpiSclkPolarity [in] spiSclkPolaritySelected" - SPI SCLK + * polarity that can be selected to either high or low + * + * Global Data : + * - None. + * + * This API is only used for the SPI frame format and will set the SPI SCLK polarity + * to either low or high + * + * @return + * - IX_SSP_SUCCESS - SPI Sclk polarity set with valid enum value + * - IX_SSP_INVALID_SPI_POLARITY_ENUM_VALUE - invalid SPI polarity value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccSpiSclkPolaritySet ( + IxSspAccSpiSclkPolarity spiSclkPolaritySelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccSpiSclkPhaseSet ( + IxSspAccSpiSclkPhase spiSclkPhaseSelected) + * + * @brief Sets the SPI SCLK Phase + * + * @param "IxSspAccSpiSclkPhase [in] spiSclkPhaseSelected" - Phase of either + * the SCLK is inactive one cycle at the start of a frame and 1/2 + * cycle at the end of a frame, OR + * the SCLK is inactive 1/2 cycle at the start of a frame and one + * cycle at the end of a frame. + * + * Global Data : + * - IX_SSP_SUCCESS - SPI Sclk phase set with valid enum value + * - IX_SSP_INVALID_SPI_PHASE_ENUM_VALUE - invalid SPI phase value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * This API is only used for the SPI frame format and will set the SPI SCLK + * phase according to user input. + * + * @return + * - None + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccSpiSclkPhaseSet ( + IxSspAccSpiSclkPhase spiSclkPhaseSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccMicrowireControlWordSet ( + IxSspAccMicrowireCtlWord microwireCtlWordSelected) + * + * @brief Sets the Microwire control word to 8 or 16 bit format + * + * @param "IxSspAccMicrowireCtlWord [in] microwireCtlWordSelected" - Microwire + * control word format can be either 8 or 16 bit format + * + * Global Data : + * - None. + * + * This API is only used for the Microwire frame format and will set the + * control word to 8 or 16 bit format + * + * @return + * - IX_SSP_SUCCESS - Microwire Control Word set with valid enum value + * - IX_SSP_TX_FIFO_NOT_EMPTY - Tx FIFO not empty, data size change is not + * allowed. + * - IX_SSP_INVALID_MICROWIRE_CTL_CMD_ENUM_VALUE - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccMicrowireControlWordSet ( + IxSspAccMicrowireCtlWord microwireCtlWordSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccTxFIFOThresholdSet ( + IxSspAccFifoThreshold txFIFOThresholdSelected) + * + * @brief Sets the Tx FIFO Threshold. + * + * @param "IxSspAccFifoThreshold [in] txFIFOThresholdSelected" - Threshold that + * is set for a Tx FIFO service request to be triggered + * + * Global Data : + * - None. + * + * This API will set the threshold for a Tx FIFO threshold to be triggered + * + * @return + * - IX_SSP_SUCCESS - Tx FIFO Threshold set with valid enum value + * - IX_SSP_INVALID_TX_FIFO_THRESHOLD_ENUM_VALUE - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccTxFIFOThresholdSet ( + IxSspAccFifoThreshold txFIFOThresholdSelected); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOThresholdSet ( + IxSspAccFifoThreshold rxFIFOThresholdSelected) + * + * @brief Sets the Rx FIFO Threshold. + * + * @param "IxSspAccFifoThreshold [in] rxFIFOThresholdSelected" - Threshold that + * is set for a Tx FIFO service request to be triggered + * + * Global Data : + * - None. + * + * This API will will set the threshold for a Rx FIFO threshold to be triggered + * + * @return + * - IX_SSP_SUCCESS - Rx FIFO Threshold set with valid enum value + * - IX_SSP_INVALID_RX_FIFO_THRESHOLD_ENUM_VALUE - invalid enum value + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccRxFIFOThresholdSet ( + IxSspAccFifoThreshold rxFIFOThresholdSelected); + + +/** + * Debug functions + */ + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccStatsGet ( + IxSspAccStatsCounters *sspStats) + * + * @brief Returns the SSP Statistics through the pointer passed in + * + * @param "IxSspAccStatsCounters [in] *sspStats" - SSP statistics counter will + * be read and written to the location pointed by this pointer. + * + * Global Data : + * - None. + * + * This API will return the statistics counters of the SSP transfers. + * + * @return + * - IX_SSP_SUCCESS - Stats obtained into the pointer provided successfully + * - IX_SSP_FAIL - client provided pointer is NULL + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccStatsGet ( + IxSspAccStatsCounters *sspStats); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccStatsReset ( + void) + * + * @brief Resets the SSP Statistics + * + * @param - None + * + * Global Data : + * - None. + * + * This API will reset the SSP statistics counters. + * + * @return + * - None + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC void +ixSspAccStatsReset ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccShow ( + void) + * + * @brief Display SSP status registers and statistics counters. + * + * @param - None + * + * Global Data : + * - None. + * + * This API will display the status registers of the SSP and the statistics + * counters. + * + * @return + * - IX_SSP_SUCCESS - SSP show called successfully. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccShow ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccSSPBusyCheck ( + void) + * + * @brief Determine the state of the SSP serial port hardware. + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return the state of the SSP serial port hardware - busy or + * idle + * + * @return + * - IX_SSP_BUSY - SSP is busy + * - IX_SSP_IDLE - SSP is idle. + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccSSPBusyCheck ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccTxFIFOLevelGet ( + void) + * + * @brief Obtain the Tx FIFO's level + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return the level of the Tx FIFO + * + * @return + * - 0..16; 0 can also mean SSP not initialized and will need to be init. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC UINT8 +ixSspAccTxFIFOLevelGet ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOLevelGet ( + void) + * + * @brief Obtain the Rx FIFO's level + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return the level of the Rx FIFO + * + * @return + * - 0..16; 0 can also mean SSP not initialized and will need to be init. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC UINT8 +ixSspAccRxFIFOLevelGet ( + void); + +/** + * @ingroup IxSspAcc + * + * @fn ixSspAccRxFIFOOverrunCheck ( + void) + * + * @brief Check if the Rx FIFO has overrun its FIFOs + * + * @param - None + * + * Global Data : + * - None. + * + * This API will return whether the Rx FIFO has overrun its 16 FIFOs + * + * @return + * - IX_SSP_OVERRUN_OCCURRED - Rx FIFO overrun occurred + * - IX_SSP_NO_OVERRUN - Rx FIFO did not overrun + * - IX_SSP_NOT_INIT - SSP not initialized. SSP init needs to be called. + * + * @li Reentrant : yes + * @li ISR Callable : yes + * + */ +PUBLIC IX_SSP_STATUS +ixSspAccRxFIFOOverrunCheck ( + void); + +#endif /* __ixp46X */ +#endif /* IXSSPACC_H */ |