diff options
Diffstat (limited to 'doc/README.m5373evb')
| -rw-r--r-- | doc/README.m5373evb | 94 |
1 files changed, 47 insertions, 47 deletions
diff --git a/doc/README.m5373evb b/doc/README.m5373evb index 4f33b7dcf2..b2ef4a5f7c 100644 --- a/doc/README.m5373evb +++ b/doc/README.m5373evb @@ -187,68 +187,68 @@ flashsize = 0x00200000 flashoffset = 0x00000000 sramstart = 0x80000000 sramsize = 0x00008000 -mbar = 0xFC000000 -busfreq = 80 MHz +mbar = 0xFC000000 +busfreq = 80 MHz ethaddr = 00:E0:0C:BC:E5:60 ip_addr = 192.168.1.3 baudrate = 115200 bps -> -> help -? - alias for 'help' +? - alias for 'help' autoscr - run script from memory -base - print or set address offset -bdinfo - print Board Info structure -boot - boot default, i.e., run 'bootcmd' -bootd - boot default, i.e., run 'bootcmd' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory -bootm - boot application image from memory +bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol -bootvx - Boot vxWorks from an ELF image -cmp - memory compare +bootvx - Boot vxWorks from an ELF image +cmp - memory compare coninfo - print console devices and information -cp - memory copy -crc32 - checksum calculation -date - get/set/reset date & time -dcache - enable or disable data cache -echo - echo args to console -erase - erase FLASH memory -flinfo - print FLASH memory information -go - start application at address 'addr' -help - print online help -icache - enable or disable instruction cache -icrc32 - checksum calculation -iloop - infinite loop on address range -imd - i2c memory display -iminfo - print header information for application image -imls - list all images found in flash -imm - i2c memory modify (auto-incrementing) -imw - memory write (fill) -inm - memory modify (constant address) -iprobe - probe to discover valid I2C chip addresses +cp - memory copy +crc32 - checksum calculation +date - get/set/reset date & time +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +icache - enable or disable instruction cache +icrc32 - checksum calculation +iloop - infinite loop on address range +imd - i2c memory display +iminfo - print header information for application image +imls - list all images found in flash +imm - i2c memory modify (auto-incrementing) +imw - memory write (fill) +inm - memory modify (constant address) +iprobe - probe to discover valid I2C chip addresses itest - return true/false on integer compare -loadb - load binary file over serial line (kermit mode) -loads - load S-Record file over serial line -loady - load binary file over serial line (ymodem mode) -loop - infinite loop on address range +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range ls - list files in a directory (default /) -md - memory display -mii - MII utility commands -mm - memory modify (auto-incrementing) -mtest - simple RAM test -mw - memory write (fill) +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) nand - NAND sub-system nboot - boot from NAND device nfs - boot image via network using NFS protocol -nm - memory modify (constant address) +nm - memory modify (constant address) ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol -reset - Perform RESET of the CPU -run - run commands in an environment variable +reset - Perform RESET of the CPU +run - run commands in an environment variable saveenv - save environment variables to persistent storage -setenv - set environment variables -sleep - delay execution for some time +setenv - set environment variables +sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol version - print monitor version -> tftp 0x40800000 uImage @@ -256,16 +256,16 @@ Using FEC0 device TFTP from server 192.168.1.3; our IP address is 192.168.1.3 Filename 'uImage'. Load address: 0x40800000 Loading: ################################################################# - ################################################################# - ########## + ################################################################# + ########## done Bytes transferred = 2053270 (1f5496 hex) -> bootm 0x40800000 ## Booting image at 40800000 ... Image Name: Linux Kernel Image - Created: 2007-11-07 20:33:08 UTC + Created: 2007-11-07 20:33:08 UTC Image Type: M68K Linux Kernel Image (gzip compressed) - Data Size: 2053206 Bytes = 2 MB + Data Size: 2053206 Bytes = 2 MB Load Address: 40020000 Entry Point: 40020000 Verifying Checksum ... OK |