diff options
Diffstat (limited to 'doc/README.m5475evb')
| -rw-r--r-- | doc/README.m5475evb | 94 |
1 files changed, 47 insertions, 47 deletions
diff --git a/doc/README.m5475evb b/doc/README.m5475evb index cec4fd0434..37d1438785 100644 --- a/doc/README.m5475evb +++ b/doc/README.m5475evb @@ -106,8 +106,8 @@ CFG_I2C_SLAVE -- define for I2C slave address CFG_I2C_OFFSET -- define for I2C base address offset CFG_IMMR -- define for MBAR offset -CONFIG_PCI -- define for PCI support -CONFIG_PCI_PNP -- define for Plug n play support +CONFIG_PCI -- define for PCI support +CONFIG_PCI_PNP -- define for Plug n play support CONFIG_SKIPPCI_HOSTBRIDGE -- SKIP PCI Host bridge CFG_PCI_MEM_BUS -- PCI memory logical offset CFG_PCI_MEM_PHYS -- PCI memory physical offset @@ -143,7 +143,7 @@ CFG_SDRAM_BASE -- defines the DRAM Base 3. COMPILATION ============== 3.1 To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux - version) from codesourcery.com was used. Download it from: + version) from codesourcery.com was used. Download it from: http://www.codesourcery.com/gnu_toolchains/coldfire/download.html 3.2 Compilation @@ -206,68 +206,68 @@ flashsize = 0x01200000 flashoffset = 0x00000000 sramstart = 0xF2000000 sramsize = 0x00001000 -mbar = 0xF0000000 +mbar = 0xF0000000 busfreq = 133.333 MHz -pcifreq = 0 MHz +pcifreq = 0 MHz ethaddr = 00:E0:0C:BC:E5:60 eth1addr = 00:E0:0C:BC:E5:61 ip_addr = 192.162.1.2 baudrate = 115200 bps -> ? -? - alias for 'help' +? - alias for 'help' autoscr - run script from memory -base - print or set address offset -bdinfo - print Board Info structure -boot - boot default, i.e., run 'bootcmd' -bootd - boot default, i.e., run 'bootcmd' +base - print or set address offset +bdinfo - print Board Info structure +boot - boot default, i.e., run 'bootcmd' +bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory -bootm - boot application image from memory +bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol -bootvx - Boot vxWorks from an ELF image -cmp - memory compare +bootvx - Boot vxWorks from an ELF image +cmp - memory compare coninfo - print console devices and information -cp - memory copy -crc32 - checksum calculation -dcache - enable or disable data cache -echo - echo args to console -erase - erase FLASH memory -flinfo - print FLASH memory information -go - start application at address 'addr' -help - print online help -icache - enable or disable instruction cache -icrc32 - checksum calculation -iloop - infinite loop on address range -imd - i2c memory display -iminfo - print header information for application image -imls - list all images found in flash -imm - i2c memory modify (auto-incrementing) -imw - memory write (fill) -inm - memory modify (constant address) -iprobe - probe to discover valid I2C chip addresses +cp - memory copy +crc32 - checksum calculation +dcache - enable or disable data cache +echo - echo args to console +erase - erase FLASH memory +flinfo - print FLASH memory information +go - start application at address 'addr' +help - print online help +icache - enable or disable instruction cache +icrc32 - checksum calculation +iloop - infinite loop on address range +imd - i2c memory display +iminfo - print header information for application image +imls - list all images found in flash +imm - i2c memory modify (auto-incrementing) +imw - memory write (fill) +inm - memory modify (constant address) +iprobe - probe to discover valid I2C chip addresses itest - return true/false on integer compare -loadb - load binary file over serial line (kermit mode) -loads - load S-Record file over serial line -loady - load binary file over serial line (ymodem mode) -loop - infinite loop on address range -md - memory display -mii - MII utility commands -mm - memory modify (auto-incrementing) -mtest - simple RAM test -mw - memory write (fill) +loadb - load binary file over serial line (kermit mode) +loads - load S-Record file over serial line +loady - load binary file over serial line (ymodem mode) +loop - infinite loop on address range +md - memory display +mii - MII utility commands +mm - memory modify (auto-incrementing) +mtest - simple RAM test +mw - memory write (fill) nfs - boot image via network using NFS protocol -nm - memory modify (constant address) -pci - list and access PCI Configuration Space +nm - memory modify (constant address) +pci - list and access PCI Configuration Space ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol -reset - Perform RESET of the CPU -run - run commands in an environment variable +reset - Perform RESET of the CPU +run - run commands in an environment variable saveenv - save environment variables to persistent storage -setenv - set environment variables -sleep - delay execution for some time +setenv - set environment variables +sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol -usb - USB sub-system +usb - USB sub-system usbboot - boot from USB device version - print monitor version -> usb start |